Caséta Wireless In-Wall Switch SPEC (369831)

Caséta Wireless In-Wall Switch SPEC (369831)
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 1 10.28/15
Caséta® Wireless In-Wall Switch
The CasétaR Wireless In-Wall Switch provides
switching of multiple load types and, when paired
with PicoR remote controls, allows wireless control
from anywhere in the space.
The CasétaR Wireless In-Wall Switch uses LutronR
patented Clear ConnectR RF Technology which
enables wireless communication with PicoR remote
controls and the LutronR Smart Bridge and Smart
Bridge PRO.
Caséta® Wireless
In-Wall Switch
Feature
Works with PicoR remote controls
Works with the LutronR App (via a Smart Bridge or Smart Bridge PRO)*
LutronR patented Clear ConnectR RF Technology works through walls
and floors
Includes Front Accessible Service Switch (FASST) for safe lamp replacement
Works with LutronR Radio Powr SavrT Occupancy and Vacancy Sensors in
standalone applications (sensors do not work with Smart Bridge or Smart
Bridge PRO)
Dual voltage (120 V~ and 277 V~)
Simple two-wire installation (no neutral wire required)
Pico® Remote Control
Lutron® Smart Bridge
and Smart Bridge PRO
PD-5WS-DV
PD-6ANS
√
√
√
√
√
√
√
√
√
√
√
√
√
Installation requires neutral wire
May need LUT-MLC for load compatibility
Switching capacity
Best load type compatibility (no LUT-MLC required)
Low minimum load requirement
√
5A
6A
√
√
* The Lutron® App is required for setup and use with the Smart Bridge and Smart Bridge PRO. The Lutron® App is compatible with iOS® devices version 6.0 or
later and AndroidTM devices 4.0 or later.
iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. Android is a trademark of Google Inc.
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
1
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 2 10.28/15
Load Type and Capacity
Model Number
Description Voltage
PD-5WS-DV-XX1, 2 Two-wire
switch
Incandescent / 120 V~
Halogen
Incandescent / 277 V~
Halogen
120 V~
MLV
277 V~
MLV
General
120 V~
Purpose Fan
120 / 277 V~ LED
120 / 277 V~ Fluorescent
120 V~
ELV
277 V~
ELV
Incandescent / Halogen
MLV
Neutral-wire 120 V~
switch
PD-6ANS-XX 2, 5
Load Type
Minimum Load
Not Ganged
Maximum Load 4
End of Gang
Middle of Gang
25 W
600 W
450 W
350 W
25 W
1350 W
1100 W
800 W
25 W
25 W
600 VA /475 W
450 VA / 350 W 350 VA / 275 W
1350 VA /1075 W 1100 VA / 875 W 800 VA / 625 W
0.4 A
3A
3A
3A
Use LUT-MLC3
Use LUT-MLC3
Use LUT-MLC3
Use LUT-MLC3
5A
5A
600 W
1350 W
4A
4A
450 W
1100 W
3A
3A
350 W
800 W
10 W
720 W
720 W
600 W
10 W
720 VA
720 VA
600 VA
Fan
0.1 A
3.6 A
3.6 A
3.6 A
LED
Fluorescent
ELV
1 bulb
1 ballast
10 W
6A
6A
720 VA
6A
6A
720 VA
5A
5A
600 VA
1
No Neutral Required.
“XX” in the model number represents color/finish code.
3 To ensure proper operation of the switch with LED, fluorescent, and ELV loads, a LUT-MLC may be required, especially at lower wattages. If the status LED
on the switch is flashing or solid red in color, a LUT-MLC must be installed. To guarantee best performance, installing a LUT-MLC with these load types
regardless of wattage is recommended. Rarely, some load types may still flicker or glow in the off state even with the LUT-MLC installed, in which case a
different load may be required.
4 See “Ganging and Derating” section.
5 Neutral required.
2
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
2
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 3 10.28/15
Specifications
•
•
•
•
•
•
Regulatory Approvals
cULus Listed
NOM Certified
FCC Approved. Complies with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules
Industry Canada Certified
IFTEL Certified
NEMA 410
Power
Operating voltage:
• PD-5WS-DV: 120 / 277 V~ 50 / 60 Hz
• PD-6ANS: 120 V~ 50 / 60 Hz
Key Design Features
• Tested to withstand electrostatic discharge without
damage or memory loss, in accordance with
IEC 61000-4-2.
• Tested to withstand surge voltages without damage
or loss of operation, in accordance with IEEE
C62.41-1991 Recommended Practice on Surge
Voltages in Low-Voltage AC Power Circuits.
• Switches always operate locally and do not require
system control.
• Power failure memory: should power be interrupted,
the control will return to its previously set level prior
to the interruption when power is restored.
• Uses conventional 3-way wiring.
• Uses LutronR ClaroR wallplates or designer-style
wallplates from other manufacturers. Wallplates are
sold separately.
•LutronR ClaroR wallplates snap on with no visible
means of attachment.
• Requires a 1-gang U.S. wallbox. 31⁄2 in (89 mm)
depth recommended, 21⁄4 in (57 mm) depth
minimum.
• Green status LED.
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
System Communications and Capacity
• The CasétaR Wireless In-Wall Switch communicates
with PicoR remote controls and the LutronR Smart
Bridge/Smart Bridge PRO through radio frequency
(RF).
•The CasétaR Wireless In-Wall Switch communicates
with LutronR Radio Powr SavrT Occupancy and
Vacancy Sensors in a standalone application.
Sensors do not work with Smart Bridge or Smart
Bridge PRO.
• The CasétaR Wireless In-Wall Switch must be located
within 60 ft (18 m) line‑of‑sight or 30 ft (9 m) through
walls, of PicoR remote controls and LutronR Smart
Bridge devices.
Device limits
•PicoR remote controls and Radio Powr SavrT
occupancy sensors: up to 10 devices (total) may be
paired to each CasétaR Wireless In‑Wall Switch (with
no Smart Bridge installed)
• Smart Bridge or Smart Bridge PRO system: up to
50 total wireless devices (CasétaR Wireless dimmers/
switches, PicoR remote controls) are supported per
system. Smart Bridge or Smart Bridge PRO counts
as one device.
Environment
• Ambient operating temperature: 32 °F to 104 °F
(0 °C to 40 °C), 0% – 90% humidity, non-condensing.
Indoor use only.
Page
3
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 4 10.28/15
Operation
Status LED
Indicates load status; glows softly as night light when load is off
On
Off
FASSTM
Front Accessible Service Switch
FASSTM — Front Accessible Service Switch
Important Notice: To service load, remove power by pulling
out the FASSTM as far as possible. To restore power after
servicing load, push the FASSTM back in completely.
Mounting
Switch Mounting Screws
Adapter Mounting Screws
Wallbox
Switch
Wallplate Adapter
Wallplate
Wallplate Adapter / Wallplate purchased separately
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
4
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 5 10.28/15
Dimensions
Front View
Side View
411⁄16 in
(119 mm)
215⁄16 in
(75 mm)
5/16 in
(8 mm)
11⁄8 in
(30 mm)
Ganging and Derating
When ganging with other switches in the same wallbox, derating is required. See “Load Type and Capacity” chart.
Do not remove outside fins on ends of ganged switches
Each switch has
inside fins removed
®
Job Name:
Job Number:
Middle of ganged switches has
all fins removed
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
5
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 6 10.28/15
Wiring Diagrams
Single Location Installation
PD-5WS-DV
Blue 1
Line/Hot
PD-5WS-DV
Black
Black
Green
120 / 277 V~ 50/60 Hz
Load
LUT-MLC 2
Ground
Neutral
PD-6ANS
Blue 1
Line/Hot
PD-6ANS
Black
120 V~ 50/60 Hz
White
Red 3
Green
Load
Ground
Neutral
1
When using controls without a mechanical 3-way switch, cap the blue terminal. Do not connect the blue wire to any other wiring or to ground.
A LUT-MLC ensures proper function when LED, fluorescent, or ELV loads are used. Install the LUT-MLC inside a load fixture or in a separate junction box
within the circuit.
3 The red wire must be connected to the load and the black wire must be connected to Line/Hot. The switch will not work if the wires are reversed.
2
(continued on next page…)
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
6
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 7 10.28/15
Wiring Diagrams (continued)
3-Way Installation
Option 1: With mechanical switch
PD-5WS-DV
Blue
Brass
Brass
Mechanical
Switch 1, 3
Line/Hot
Black
Black
PD-5WS-DV 1
Black
Jumper wire
120 / 277 V~ 50/60 Hz
Green
Ground
Load
LUT-MLC 2
Ground
Neutral
PD-6ANS (Load-side)
Blue
Brass
Brass
Mechanical
Switch 1, 3
Line/Hot
Black
Black
120 V~ 50/60 Hz
PD-6ANS 1
Red 4
Jumper wire
Ground
White
Green
Load
Ground
Neutral
PD-6ANS (Line-side)
Blue
Black
Line/Hot
PD-6ANS 1
Red 4
Brass
Brass
Mechanical
Switch 1, 3
Black
120 V~ 50/60 Hz
White
Green
Jumper wire
Load
Ground
Ground
Neutral
1
Location of Caséta® Wireless In-Wall Switch and mechanical switch may be reversed.
A LUT-MLC ensures proper function when LED, fluorescent, or ELV loads are used. Install the LUT-MLC inside a load fixture or in a separate junction box within the circuit.
3 A second location requires rewiring.
4 The red wire must be connected to the load and the black wire must be connected to Line/Hot. The switch will not work if the wires are reversed.
2
(continued on next page…)
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
7
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 8 10.28/15
Wiring Diagrams (continued)
3-Way Installation
Option 2: With Pico® remote controls (PJ2-2B-xx) and wallbox mounting adapters (PICO-WBX-ADAPT)
PD-5WS-DV
Black
Pico®
Remote
Control and
Wallbox
Mounting
Adapter 3
Line/Hot
Black
Blue1
Travelers
PD-5WS-DV
Black
Green
120 / 277 V~ 50/60 Hz
Load
LUT-MLC 2
Ground
Neutral
PD-6ANS
Black
Pico®
Remote
Control and
Wallbox
Mounting
Adapter 3
Line/Hot
Black
Blue1
Travelers
PD-6ANS
White
120 V~ 50/60 Hz
Red4
Green
Load
Ground
Neutral
1
When using controls without mechanical 3-way switch, cap the blue terminal. Do not connect the blue wire to any other wiring or to ground.
A LUT-MLC ensures proper function when LED, fluorescent, or ELV loads are used. Install the LUT-MLC inside a load fixture or in a separate junction box
within the circuit.
3 A second location requires rewiring.
4 The red wire must be connected to the load and the black wire must be connected to Line/Hot. The switch will not work if the wires are reversed.
2
(continued on next page…)
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
8
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 9 10.28/15
Wiring Diagrams (continued)
Multi-location Installation (for installations where 3 or more switches control the load)
With Pico® remote controls (PJ2-2B-xx) and wallbox mounting adapters (PICO-WBX-ADAPT)
PD-5WS-DV
Black
Pico®
Remote
Control and
Wallbox
Mounting
Adapter 3
Line/Hot
Black
Travelers
Pico®
Remote
Control and
Wallbox
Mounting
Adapter 3
Blue1
Travelers
PD-5WS-DV
Black
Green
120 / 277 V~ 50/60 Hz
Load
LUT-MLC 2
Ground
Neutral
PD-6ANS
Black
Pico®
Remote
Control and
Wallbox
Mounting
Adapter 3
Line/Hot
Black
Travelers
Pico®
Remote
Control and
Wallbox
Mounting
Adapter 3
PD-6ANS
White
120 V~ 50/60 Hz
Blue1
Travelers
Red 4
Green
Load
Ground
Neutral
1
When using controls without mechanical 3-way switch, cap the blue terminal. Do not connect the blue wire to any other wiring or to ground.
A LUT-MLC ensures proper function when LED, fluorescent, or ELV loads are used. Install the LUT-MLC inside a load fixture or in a separate junction box
within the circuit.
3 Each location requires rewiring.
4 The red wire must be connected to the load and the black wire must be connected to Line/Hot. The switch will not work if the wires are reversed.
2
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
9
Caséta® Wireless
PD-5WS-DV, PD-6ANS
In-Wall Switch
369831c 10 10.28/15
Colors and Finishes
Gloss Finishes
White
WH
Black
BL
Ivory
IV
Light Almond
LA
ue to printing limitations, colors and finishes shown
D
cannot be guaranteed to perfectly match actual
product colors.
®
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising