advertisement
FA-G41A
PICMG 1.0 with Intel
®
G41 support LGA775 Intel
®
Core2
TM
Quad CPU Card With VGA, DDR3,
Dual PCIe GbE, SATA II, COM, USB 2.0 and Audio
User's Manual (V1.0)
健昇科技股份有限公司
JS AUTOMATION CORP.
新北市汐止區中興路 100 號 6 樓
6F., No.100, Zhongxing Rd.,
Xizhi Dist., New Taipei City, Taiwan
TEL：+886-2-2647-6936
FAX：+886-2-2647-6940 http://www.automation.com.tw http://www.automation-js.com/
E-mail：[email protected]
Contents
1
1. Forward
Thank you for your selection of FA-G41A cpu card.
Any comment is welcome, please visit our website: www.automation.com.tw for the up to date information.
2
2. Features
PCIMG 1.0
RoHS compliant
LGA775 CPU socket
Supports two DDR3 DIMMs
Two Gigabit Ethernet connectors
Four SATA connectors
High Definition audio to connect to an optional audio kit
3
3. Specifications
Form Factor : PCIMG 1.0
CPU Supported : Socket LGA775 Intel ®
Core™2 Duo/Quad/Extreme, Celeron Front Side Bus
(FSB) : 800/1066/1333 MHz
Front Side Bus (FSB) : 800/1066/1333 MHz
Northbridge Chipset : Intel ®
G41
Integrated Graphics : GA DVI (FA-G41A-DVI only)
Memory : Two DDR3 modules up to 2 GB each (4 GB total)
Southbridge Chipset : Intel ®
ICH7
BIOS : AMI BIOS
Digital I/O : 8-bit, 4-bit input/4-bit output
Ethernet Controllers : Dual Realtek RTL8111CP
Super I/O Controller : iTE IT8718F
Watchdog Timer : Software programmable supports 1~255 sec. system reset
Audio Connectors : One internal audio connector
Keyboard/Mouse : One external PS/2, one internal pin header
Serial Ports : Two RS-232 COM connectors
USB 2.0/1.1 ports : Six internal via pin header One external
Floppy Disk Drives : One floppy disk drive (FDD) connector
IDE : One IDE connector
Serial ATA : Four independent SATA channels with 3.0 Gb/s data transfer rates
Environmental and Power Specifications
Power Supply : ATX power supported
Power Consumption : 5 V @ 7.13 A 12 V @ 0.27 A 5VBS @ 0.11 A Vcore @ 3.02 A
3D Mark2001SE with Intel
®
Core™2 Duo E8500 3.16GHz and two 2GB DDR3 modules
Operating temperature : 0ºC ~ 60ºC( 32°F ~ 140°F), requires cooler and silicone heat sink paste
Humidity : 5% ~ 95% (non-condensing)
Physical Specifications
Dimensions : 338 mm x 122 mm
Weight GW : 1100 g
4
4. Dimensions
5
5. Jumper and Connector Locations
5.1 FA-G41A Layout
6
5.2 Peripheral Interface Connectors
Connector Type
ATX Power Control Connector 3-pin wafer (1x3)
Audio Kit Connector
Battery Connector
CPU Fan Connector
CPU Power Input Connector
DVI Connector
10-pin header
2-pin wafer (1x2)
4-pin header
4-pin connector
26-pin header
Digital I/O Connector
Floppy Disk Connector
Front Panel Connector
Infrared Interface Connector
Keyboard Connector
Memory Slot
IDE Connector
Parallel Port Connector
10-pin header
34-pin header
14-pin header
5-pin header (1x5)
5-pin header (1x5)
DIMM slot
40-pin box header
26-pin box header
SATA Drive Connectors
Serial Port Connector
SPI Flash Connector
USB Connectors
7-pin SATA drive connectors
10-pin box header
8-pin header
8-pin header
5.3 External Interface Panel Connectors
Connector Type
Keyboard/Mouse Connector PS/2
LAN Connector RJ-45
USB Connector
VGA Connector
Label
KB_MS1
LAN1, LAN2
USB port USB_C1
15-pin Female VGA1
Label
ATXCTL1
J_AUDIO1
BAT1
CPU_FAN1
CPU12V1
DVI1
DIO1
FDD1
F_PANEL1
IR1
KB1
DIMM1, DIMM2
PIDE1
LPT1
SATA1, SATA2, SATA3,
SATA4
COM1, COM2
JSPI1
USB1
7
6. Connector and Jumper setting
6.1 Peripheral Interface Connectors
6.1.1 ATX Power Control Connector
(ATXCTL1 : 3-pin wafer (1x3))
The connector is for enabling an ATX power supply. When connected to the power supply, the power can be turned on and off with the front panel switch.
Pin Description
1
2
3
GND
ATX_ON
5VSB
6.1.2 Audio Kit Connector
(J_AUDIO1: 10-pin header)
This connector connects to an external audio kit.
Pin Description
1
3
5
7
9
ACZ_SYNC
ACZ_SDOUT
ACZ_SDIN
ACZ_VCC
ACZ_12 V
Pin
2
4
6
8
10
Description
ACZ_BITCLK
ACZ_PCBEEP
ACZ_RST#
ACZ_GND
ACZ_ GND
6.1.3 Battery Connector
(BAT1: 2-pin wafer (1x2))
This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.
Pin Description
1
2
Battery+
Ground
8
6.1.4 CPU Fan Connector
(CPU_FAN1: 4-pin header)
The fan connector attaches to a CPU cooling fan.
Pin Description
1 GND
2 +12 V
3 Rotation signal
4 Control
6.1.5 CPU Power Input Connector
(CPU12V1: 4-pin connector)
The CPU power input connector provides power to the CPU.
Pin Description
1
2
GND
GND
3
4
+12 V
+12 V
6.1.6 DVI Connector
(DVI1: 26-pin header)
The DVI connector connects to a monitor that supports DVI video input.
Pin Description
7
8
9
10
11
12
13
1
2
3
4
5
6
Data 2
Data 2+
GND
N/C
N/C
DDC Clock
DDC Data
N/C
Data 1
Data 1+
GND
N/C
N/C
Pin
20
21
22
23
24
25
26
14
15
16
17
18
19
9
Description
VCC
GND
Hot Plug Detect
Data0
Data 0+
GND
N/C
N/C
GND
Clock+
Clock
GND
6.1.7 Digital I/O Connector
(DIO1: 10-pin header)
The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input.
Pin Description Pin Description
1
3
5
7
9
GND
Output 3
Output 1
Input 3
Input 1
2
4
6
8
10
VCC
Output 2
Output 0
Input 2
Input 0
6.1.8 Floppy Disk Connector
(FDD1: 34-pin header)
The floppy disk connector is connected to a floppy disk drive.
Pin Description Pin
21
23
25
27
29
31
33
1
3
5
7
9
11
13
15
17
19
GND
GND
GND
GND
GND
GND
GND
GND
GND
N/C
GND
GND
GND
GND
GND
GND
GND
Description
22
24
26
28
30
32
34
2
4
REDUCE WRITE
N/C
6 N/C
8 INDEX#
10 MOTOR ENABLE A#
12 DRIVE SELECT B#
14 DRIVE SELECT A#
16 MOTOR ENABLE B#
18
20
DIRECTION#
STEP#
WRITE DATA#
WRITE GATE#
TRACK 0#
WRITE PROTECT#
READ DATA#
SIDE 1 SELECT#
DISK CHANGE#
10
6.1.9 Front Panel Connector
(F_PANEL1: 14-pin header)
The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.
Pin Description Pin Description
1
3
5 GROUND 6
7 Power button+ 8
9 Power button- 10
11
13
+5 V
N/C
+5 V
HDD LED
2
4
+5 V
N/C
N/C
Speaker
N/C
12 Reset
14 GROUND
6.1.10 Infrared Interface Connector
(IR1: 5-pin header (1x5))
The infrared connector attaches to an infrared receiver for use with remote controls.
Pin Description
1
2
VCC
NC
3
4
5
IR-RX
GND
IR-TX
6.1.11 Keyboard Connector
(KB1: 5-pin header (1x5))
The keyboard connector can be used to install a PS/2 keyboard.
Pin Description
1 KEYBOARD CLOCK
2
3
4
5
KEYBOARD DATA
N/C
GROUND
VCC
11
6.1.12 Memory Slot
(DIMM1, DIMM2 : DIMM slot)
The DIMM slots are for DIMM memory modules.
6.1.13 IDE Connector
(PIDE1: 40-pin box header)
Connects to IDE hard drives and optical drives.
Pin
13
15
17
19
21
1
3
5
7
9
11
23
25
27
29
31
33
35
37
39
Description
RESET#
DATA 7
DATA 6
DATA 5
DATA 4
DATA 3
DATA 2
DATA 1
DATA 0
GROUND
IDE DRQ
IOW#
IOR#
IDE CHRDY
IDE DACK
INTERRUPT
SA1
SA0
HDC CS0#
HDD ACTIVE#
Pin
14
16
18
20
22
2
4
6
8
10
12
24
26
28
30
32
34
36
38
40
Description
GROUND
DATA 8
DATA 9
DATA 10
DATA 11
DATA 12
DATA 13
DATA 14
DATA 15
N/C
GROUND
GROUND
GROUND
BALE—DEFAULT
GROUND
N/C
PDIAG#
SA2
HDC CS1#
GROUND
12
6.1.14 Parallel Port Connector
(LPT1: 26-pin box header)
The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.
Pin
5
6
7
8
1
2
3
4
9
10
11
12
13
Description Pin Description
STROBE#
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7 22
ACKNOWLEDGE# 23
BUSY 24
PAPER EMPTY
PRINTER SELECT
25
18
19
20
21
14
15
16
AUTO FORM FEED#
ERROR#
INITIALIZE#
17 PRINTER SELECT LN#
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
6.1.15 SATA Drive Connectors
(SATA1, SATA2, SATA3, SATA4 : 7-pin SATA drive connectors)
The SATA drive connectors can be connected to SATA drives.
Pin Description
1
2
3
4
5
6
7
8
GND
TX+
TX
GND
RX
RX+
GND
N/C
13
6.1.16 Serial Port Connector
(COM1, COM2: 10-pin box header)
This connector provides RS-232 communications.
Pin Description
1 Data Carrier Detect (DCD1)
2 Receive Data (RXD1)
3 Transmit Data (TXD1)
4 Data Terminal Ready (DTR1)
5 Ground (GND1)
6 Data Set Ready (DSR1)
7 Request To Send (RTS1)
8 Clear To Send (CTS1)
9 Ring Indicator (RI1)
10 NC
6.1.17 SPI Flash Connector
(JSPI1: 8-pin header)
The 8-pin SPI Flash connector is used to flash the BIOS.
Pin Description Pin Description
1
3
5
7
VCC
CS#
SO
NC
2
4
6
8
GND
CLOCK
SI
NC
6.1.18 USB Connectors
(USB12, USB34, USB56: 8-pin header)
The USB connectors connect to USB devices. Each pin header provides two USB ports.
Pin Description Pin Description
1
3
5
7
VCC
DATA1
DATA1+
GND
2
4
6
8
GND
DATA+
DATA
VCC
14
6.2 External Interface Connector
6.2.1 Keyboard/Mouse Connector
(KBMS1 : PS/2)
The keyboard and mouse connector is a standard PS/2 connector.
Pin Description
1 KEYBOARD DATA
2 MOUSE DATA
3 GROUND
4 VCC
5 KEYBOARD CLOCK
6 MOUSE CLOCK
6.2.2 LAN Connectors
(LAN1, LAN2: RJ-45)
The LAN connector connects to a local network.
Pin Description Pin Description
1
2
3
4
MDIA3
MDIA3+
MDIA2
MDIA1
5
6
7
8
MDIA1+
MDIA+
MDIA0
MDIA0+
15
6.2.3 USB Connector
(USB_C1: USB port)
The USB connector can be connected to a USB device..
Pin Description Pin Description
1
3
VCC
DATA+
2
4
DATA
GROUND
6.2.4 VGA Connector
(VGA1 : 15-pin Female)
The VGA connector connects to a monitor that accepts a standard VGA input.
Pin Description Pin Description
1
9
11
13
15
3
5
7
RED
BLUE
GND
GND
VCC
NC
HSYNC
DDCCLK
2
4
6
8
10
12
14
GREEN
NC
GND
GND
GND
DDC DAT
VSYNC
16
7. Ordering information
PRODUCT DESCRIPTIONS
JD50FAG41A PICMG 1.0 with Intel
®
G41 support LGA775 Intel
®
Core2
TM
Quad CPU
Card With VGA, DDR3, Dual PCIe GbE, SATA II, COM, USB 2.0 and
Audio
17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement