cd micro system - Product Care Product Care

CD MICRO SYSTEM
Instruction Manual
Model Number: GSMIC2001
Please read these instructions carefully and keep for future reference
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
WARNING
1. WARNING：Please refer to the information on the bottom of the product for electrical and safety information
before installing or operating the apparatus.
2. WARNING：To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The
apparatus should not be exposed to dripping or splashing and objects filled with liquids, such as vases, should
not be placed on the apparatus.
3. WARNING: The mains plug is used as a disconnect device, the disconnect device should remain readily operable.
4.
Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam of laser.
5.
Correct Disposal of this product. This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
6. No naked flame sources, such as lighted candles, should be placed on the apparatus.
7. Use of the apparatus in moderate climates only.
8. The rating and marking information are located on the bottom of the unit.
9. The mains plug of the unit should not be obstructed and should be easily accessed during intended use.
10. To completely disconnect the power input, the mains plug of the apparatus should be disconnected from the
mains.
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
1
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
LIGHTNING FLASH WITH ARROWHEAD SYMBOL -
EXCLAMATION POINT - within an equilateral triangle,
within an equilateral triangle, is intended to alert the
is used to indicate that a specific component shall be
user to the presence of uninsulated dangerous
replaced only by the component specified in that
voltage within the products enclosure that may be of
documentation for safety reason.
sufficient magnitude to constitude a risk of electric
shock to persons.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
This label is attached to the product to inform the apparatus
contains a laser component.
WARNING LABEL INFORMING OF RADIATION This label is placed inside the unit, to warn that the equipment
contains a laser radiating laser rays according to the limit of laser
product of class 1.
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
2
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundry tub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on a bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to a power supply only of the type described in the
operating instructions or as marked on the appliance.
9. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them.
10. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into the
enclosure through openings.
11. ESD WARNING – If the display does not function properly or there is no reaction to the operation of controls, this
may be due to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few minutes.
12. SERVICING - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
13. SERVICING - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconnect the AC cord. Then turn the power back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
3
LOCATION OF CONTROL
1.) LCD DISPLAY
2.) POWER INDICATOR
3.) FM ST. INDICATOR
4.) VOLUME CONTROL
5.) REPEAT
6.) SKIP 7.) SKIP +
8.) BAND SELECTOR
9.) TUNING CONTROL
10.) PROGRAM
11.) PLAY / PAUSE
12.) STOP
13.) FUNCTION SELECTOR
14.) AUX IN
15.) FM ANTENNA
16.) POWER ON / OFF
1
2
3
4
5
10
6
11
7
12
8
13
14
9
17.) SPEAKER JACKS ( L / R )
18.) TIME SET
19.) HOUR
20.) MINUTE
21.) AC POWER CORD
15
18
16
19
20
17
21
POWER SOURCE
AC POWER
You can power your appliance by plugging the AC power cord into a wall AC power outlet. Check
that the rated voltage of your appliance matches your local voltage.
Make sure that the AC power cord is fully inserted into the wall AC power outlet.
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
4
RADIO OPERATION
SETTING UP YOUR SYSTEM
1. Connect the speaker plugs from the speakers into the L/R speaker jacks located on the back of the
system.
2. Fully extend the FM aerial wire.
3. Connect the mains plug to a suitable 13 Amp mains socket.
4. Switch ON the system using the Power ON/OFF switch located at the back of the system.
5. Slide the function selector switch on the front of the system from Stand-by to either Radio or CD
mode.
GENERAL OPERATION
1. Ensure you have Switched ON the System using the Power ON/OFF switch located at the back of
the system.
2. Set the “FUNCTION” selector to “RADIO” mode.
3. Select the desired band by using the “BAND” selector.
4. Adjust the radio frequency to your desired station by using the “TUNING” control.
5. Adjust the “VOLUME” control to the desired level.
FM / FM-STEREO RECEPTION
- Set the “BAND” selector to FM mode for MONO reception.
- Set the “BAND” selector to FM ST. mode for FM STEREO reception. The Stereo indicator light up
to show FM ST. mode.
FOR BETTER RECEPTION
FM - This appliance has a FM antenna located at the rear cabinet. This wire is completely unraveled
and extended for better reception.
AM - This appliance is equipped with a built - in directional ferrite AM antenna. Rotate the appliance
to get better reception.
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
5
CD OPERATION
GENERAL OPERATION
PLAY / PAUSE
SKIP +
, SKIP -
STOP
Press to start playing CD disc.
Press again to pause CD playback temporarily.
Press again to resume playback.
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the desired point
on the sound track.
Press to stop all CD operation.
PLAYBACK
1. Ensure you have Switched ON the System using the Power ON/OFF switch located at the back of
the system.
2. Set the “FUNCTION” selector to “CD” mode.
3. Open the CD door and place a CD disc with the label facing up in the CD compartment.
4. Gently push the disc on to the centre holder until it clips into place.
5. Close the CD door.
6. Focus search is performed if a disc is inside. The total number of tracks will be read and displayed
on the display.
7. Press the “PLAY / PAUSE” button to start playing the CD.
8. Adjust the “VOLUME” control to the desired level.
9. Press the “PLAY / PAUSE” button again when you want to pause playback.
10. Press the “STOP” button when finished.
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
6
CD OPERATION
PROGRAM
Up to 20 tracks can be programmed for disc playback in any order.
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button.
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed. Press the “PLAY / PAUSE” button to play the
disc in the order you have programmed and the program indicator flashes.
6. Press the “STOP” button once to terminate programmed playback and the program indicator
will turn off.
7. Press the “PROGRAM”, and “PLAY/PAUSE” button to resume programmed playback.
8. Turn the function selector to “OFF” position to clear the programmed memory.
REPEAT
Press the “REPEAT” button before or during CD playback,
each press switches the mode function as follows:
1 - REPEAT 1
2 - REPEAT ALL
3 - NORMAL PLAYBACK
REP
REP
ALL
REPEAT 1
REPEAT
ALL
NORMAL
PLAYBACK
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
7
OTHER FEATURES
CLOCK SETTING
1. Press and hold the “TIME SET” button. (Do not release the “TIME SET” button during time setting).
2. Press the “HOUR” button to set the hour.
3. Press the “MINUTE” button to set the minutes.
4. Release all button to confirm setting. Confirmed setting will be displayed on the display.
Please note you will need to reset the clock if you unplug the system from the mains socket or switch it
off using the ON/OFF switch located at the back of the system.
AUX IN
1. Ensure you have Switched ON the System using the Power ON/OFF switch located at the back of
the system.
2. Use a 3.5mm Male-to-Male Stereo cable to connect any external audio device with a 3.5mm.
Headphone or Line-Out jack to the AUX IN jack on the front panel of the stereo. The system will
automatically switch to the Aux mode.
3. Start playback on the external audio device.
4. Adjust the volume on the audio device (do not set the volume too high to avoid distortion). You may
also adjust the volume on the micro system.
5. Use the controls provided by the external audio device to control the playback function.
SPECIFICATIONS
Supply Voltage:…………..220V – 240V ~ 50Hz
Frequency range……….. 87.5-108MHz (FM)
540-1600kHz (AM)
Net Weight:………………..2.6 kg
Power Consumption : 12.5 Watts
Power Output per Channel: 2 Watts (RMS)
Total Power Output : 2 x 2 Watts(RMS)
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
8
Guarantee
This product is guaranteed for 12 months from the date of original purchase.
If any defect arises due to faulty materials or workmanship, the unit will, either
be repaired, replaced or refunded at our discretion.
The following conditions apply:
● The product must be returned to the retailer with original proof of
purchase.
● The product must be installed and used in accordance with the
instructions contained in this user instruction guide.
● It must be used only for domestic purposes.
● It does not cover wear and tear, damage, misuse or consumable parts.
● The supplier has no responsibility for incidental or consequential loss or
damage.
● Valid in the UK & Eire only.
● Valid only if purchased from the SDHS Group
Postal Address:
Shop Direct Group
L70 1AB
Box MPRC8
For Customer Services & Spare Parts
please call 01204 664 084
Opening times: Monday – Friday
9am until 5pm
Revision 1
This symbol is known as the 'Crossed-out wheelie bin Symbol'. When this symbol is
marked on a product/batteries, it means that the product/batteries should not be disposed
of with your general household waste. Only discard electrical/electronic/battery items in
separate collection schemes, which cater for the recovery and recycling of materials
contained within. Your co-operation is vital to make sure the success of these schemes
and foR the protection of the environment. For your nearest disposal facility, visit
www.recycle-more.co.uk or ask in store for details.
We reserve the right due to possible changes to design to alter the instruction manual
without prior notice.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project