TS3 Install Guide

TS3 Install Guide
Transducer_Switch_Install_531870-1_C.qxp:530511-2_A - TrollingMotor_IG_prfC.qxd
8/4/14
5:41 PM
Page 4
4
531870-1_C
Transducer Switch
5. Powering Off
It is important to make sure all accessories (switches, control heads, etc.) are
powered off in order to avoid possibly draining the battery. To make sure your
Transducer Switch is disengaged, follow the steps below.
If your Transducer Switch is connected to the fuse panel:
1. Power off your boat to disengage the switch.
If your Transducer Switch is connected to a battery switch:
1. Turn the dial of the battery switch to the OFF position.
If your Transducer Switch is connected directly to a battery:
1. Power off your boat.
2. Remove the Transducer Switch wires from the battery.
Contact Humminbird
Web site
E-mail
Telephone
Direct Shipping
humminbird.com
service@humminbird.com
1-800-633-1468
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING! This device should not be used as a navigational aid to prevent
collision, grounding, boat damage, or personal injury. When the boat is moving,
water depth may change too quickly to allow time for you to react. Always operate
the boat at very slow speeds if you suspect shallow water or submerged objects.
WARNING! Disassembly and repair of this electronic unit should only be
performed by authorized service personnel. Any modification of the serial number
or attempt to repair the original equipment or accessories by unauthorized
individuals will void the warranty.
WARNING! This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Johnson
Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating
in compliance with known and applicable environmental regulations, and a good
neighbor in the communities where we make or sell our products.
WEEE Directive: EU Directive 2002/96/EC “Waste of Electrical and Electronic
Equipment Directive (WEEE)” impacts most distributors, sellers, and
manufacturers of consumer electronics in the European Union. The WEEE
Directive requires the producer of consumer electronics to take responsibility for
the management of waste from their products to achieve environmentally
responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed and
intended as fixed or temporary installation in transportation vehicles such as
automobiles, aircraft, and boats. In some European Union member states,
these vehicles are considered outside of the scope of the Directive, and EEE
for those applications can be considered excluded from the WEEE Directive
requirement.
This symbol (WEEE wheelie bin) on product indicates the product
must not be disposed of with other household refuse. It must be
disposed of and collected for recycling and recovery of waste EEE.
Johnson Outdoors Marine Electronics, Inc. will mark all EEE products
in accordance with the WEEE Directive. It is our goal to comply in the
collection, treatment, recovery, and environmentally sound disposal of those
products; however, these requirements do vary within European Union
member states. For more information about where you should dispose of your
waste equipment for recycling and recovery and/or your European Union
member state requirements, please contact your dealer or distributor from
which your product was purchased.
1
Overview
Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read
these instructions carefully in order to get the full benefit from your Humminbird® accessory.
Transducer Switch
The Transducer Switch comes with all the necessary hardware to allow you to connect your control head to two
transducers. The transducers may be the same type of transducer with different mounting locations, or you can
maximize your unit’s performance by using two different transducers. The switch is intended for installation on the
console, and will work well on almost any boat.
Customer Service: If you find that any items are missing from your installation kit, visit our Web site at
humminbird.com or call Customer Service at 1-800-633-1468.
Supplies: In addition to the hardware supplied with your Transducer Switch, you will need a hand drill with various
size bits, a Phillips screwdriver, an adjustable wrench, and a 3 amp fuse.
Installation
Perform the procedures in the following sections to install the Transducer Switch on your boat. Before installing the
Transducer Switch, gather all the parts you will need, and make sure that the planned location of the Transducer
Switch will allow you to connect the two transducers to your control head.
1. Locating the Transducer Switch Mounting Position
Mounting the Switch
There are two ways to find the mounting location, as follows:
Switch Panel: If your console already contains a switch panel with an available slot, slide the Transducer Switch into
the designated slot until it snaps into place. Proceed to procedure two.
boat
console
In-Dash: If your console does not have a switch panel or a pre-made mounting location, you will need to create one
yourself.
To manually create a mounting location:
switch
1. Locate a suitable, flat area of the dash to mount the Transducer Switch. The switch requires a depth of at least
1.5 inches (38.1 millimeters). Make sure that it will be positioned near your control head on the console of the
boat, within reach of the cables for both transducers. Also, make sure you have access behind the panel in order
to attach the cables.
2. Tape the template (included) over the desired in-dash mounting location.
3. At a location inside the dotted line on the template, drill a hole large enough to insert the blade of the
reciprocating saw. Carefully begin cutting toward the dotted line, then follow the dotted line around the
template. Remove the template when finished.
4. Insert the end of the switch through the hole until it snaps securely in place.
2. Connecting the Transducers and the Control Head to the Switch
To connect your Transducer Switch to your control head, you may have to remove the control head from the Quick
Disconnect Mounting Bracket and temporarily disassemble the connector holder.
NOTE: Your connector holder hardware may be different than the illustration, depending on your Humminbird model. See
your control head installation guide for details.
CAUTION! Do NOT mount the cables where the connectors could be submerged in water or flooded. If cables are installed
in a splash-prone area, it may be helpful to apply dielectric grease to the inside of the connectors to prevent corrosion.
Dielectric grease can be purchased separately from a general hardware or automotive store.
© 2014 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
531870-1_C
Transducer Switch
CAUTION! Do not cut or shorten the transducer cables, and try not to damage the cable insulation. Route the cable as far
as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference. If the cable is
too short, extension cables are available to extend the transducer cable up to a total of 50 feet. For assistance, contact
Customer Service.
Transducer_Switch_Install_531870-1_C.qxp:530511-2_A - TrollingMotor_IG_prfC.qxd
8/4/14
5:41 PM
Page 2
2
531870-1_C
Transducer Switch
531870-1_C
Transducer Switch
3. Connecting the Power Cable
To connect the transducers to the Transducer Switch:
1. Access your transducer cables and insert each transducer cable connector into a Transducer Switch connector
until you hear it click into place. Refer to the illustration for guidance.
Connecting to a Fuse Panel
Connect the Transducer Switch power cable to the boat’s fuse panel (usually located near the console). If you must
connect to a battery, connect to a battery switch (not included).
Transducer Switch Configuration
1a. If a fuse terminal is available, use crimp-on type electrical connectors (not included) that match the terminal on
the fuse panel. Attach the black wire to ground (-), and the red wire to positive (+) 12 VDC power. Install a 3 amp
fuse (not included) for protection of the unit. Humminbird is not responsible for over-voltage or over-current
failures.
control head
transducer switch
3
or...
1b. If you need to wire the control head to a battery, obtain and install an inline fuse holder, a 3 amp fuse (not
included) for the protection of the unit, and a battery switch (not included). Install the battery switch using the
instructions provided with it.
connector holder
Connecting the Connector Clips
to the Transducer Switch
NOTE: If you are unable to obtain a battery switch and are forced to connect the power cable directly to the battery, be
aware that this may cause a slow loss of power over time. See procedure five, Powering Off.
NOTE: Humminbird is not responsible for over-voltage or over-current failures. The control head must have adequate
protection through the proper selection and installation of a 3 amp fuse.
route connector to the unit
switch
2. Secure the installation with cable ties (optional).
Your Transducer Switch is now ready for operation.
connector clips
4. Switching Transducers
Perform the following procedures to alternate between the transducers connected to your Transducer Switch.
Changing Transducers
in the Menu System
To activate a transducer:
standard transducer
second transducer
1. Press the Transducer Switch to select the desired transducer.
Inserting the Cable Connector
NOTE: Use caution while sliding the transducer connectors into the Transducer Switch connectors. The slots for the
connectors are keyed to prevent reversed installation, so do not force the connectors together. See your control head
installation guide for additional information.
3. In any view, press the MENU key twice to open the Main Menu.
4. Press the RIGHT or LEFT Cursor keys to highlight the Sonar menu tab.
To connect the connector clips to the Transducer Switch:
5. Press the DOWN Cursor key to select Transducer Select.
1. From the back side of the panel, plug the two connector clips from the switch assembly into the two outlets of
the Transducer Switch.
NOTE: This feature may appear as either Transducer Select or Connected Transducer, depending on your model.
NOTE: Connecting the connector clips to the Transducer Switch does not require a specific order; either connector will work
with either outlet.
6. Press the RIGHT or LEFT Cursor keys to select a transducer.
To connect the control head to the Transducer Switch:
Sonar Menu
1. Remove the connector holder from your control head.
2. Insert the Transducer Switch cable connector into the T2 slot (transducer slot) of the connector holder.
NOTE: The slots are keyed to prevent reversed installation, so be careful not to force the connector into the holder. See your
control head installation guide for additional information.
700 Series™ with Ethernet NOTE: If you are installing the Speed Sensor accessory (optional), insert the Sonar/Speed
Y-Cable connector into the T2 slot on the connector holder. Then, connect the transducer connector and speed sensor
connector to the corresponding connectors on the Y-Cable. The Y-Cable requires a separate purchase. Contact Customer
Service for details.
2. Turn on your control head.
connector holder
transducer switch
cable connector
Transducer_Switch_Install_531870-1_C.qxp:530511-2_A - TrollingMotor_IG_prfC.qxd
8/4/14
5:41 PM
Page 2
2
531870-1_C
Transducer Switch
531870-1_C
Transducer Switch
3. Connecting the Power Cable
To connect the transducers to the Transducer Switch:
1. Access your transducer cables and insert each transducer cable connector into a Transducer Switch connector
until you hear it click into place. Refer to the illustration for guidance.
Connecting to a Fuse Panel
Connect the Transducer Switch power cable to the boat’s fuse panel (usually located near the console). If you must
connect to a battery, connect to a battery switch (not included).
Transducer Switch Configuration
1a. If a fuse terminal is available, use crimp-on type electrical connectors (not included) that match the terminal on
the fuse panel. Attach the black wire to ground (-), and the red wire to positive (+) 12 VDC power. Install a 3 amp
fuse (not included) for protection of the unit. Humminbird is not responsible for over-voltage or over-current
failures.
control head
transducer switch
3
or...
1b. If you need to wire the control head to a battery, obtain and install an inline fuse holder, a 3 amp fuse (not
included) for the protection of the unit, and a battery switch (not included). Install the battery switch using the
instructions provided with it.
connector holder
Connecting the Connector Clips
to the Transducer Switch
NOTE: If you are unable to obtain a battery switch and are forced to connect the power cable directly to the battery, be
aware that this may cause a slow loss of power over time. See procedure five, Powering Off.
NOTE: Humminbird is not responsible for over-voltage or over-current failures. The control head must have adequate
protection through the proper selection and installation of a 3 amp fuse.
route connector to the unit
switch
2. Secure the installation with cable ties (optional).
Your Transducer Switch is now ready for operation.
connector clips
4. Switching Transducers
Perform the following procedures to alternate between the transducers connected to your Transducer Switch.
Changing Transducers
in the Menu System
To activate a transducer:
standard transducer
second transducer
1. Press the Transducer Switch to select the desired transducer.
Inserting the Cable Connector
NOTE: Use caution while sliding the transducer connectors into the Transducer Switch connectors. The slots for the
connectors are keyed to prevent reversed installation, so do not force the connectors together. See your control head
installation guide for additional information.
3. In any view, press the MENU key twice to open the Main Menu.
4. Press the RIGHT or LEFT Cursor keys to highlight the Sonar menu tab.
To connect the connector clips to the Transducer Switch:
5. Press the DOWN Cursor key to select Transducer Select.
1. From the back side of the panel, plug the two connector clips from the switch assembly into the two outlets of
the Transducer Switch.
NOTE: This feature may appear as either Transducer Select or Connected Transducer, depending on your model.
NOTE: Connecting the connector clips to the Transducer Switch does not require a specific order; either connector will work
with either outlet.
6. Press the RIGHT or LEFT Cursor keys to select a transducer.
To connect the control head to the Transducer Switch:
Sonar Menu
1. Remove the connector holder from your control head.
2. Insert the Transducer Switch cable connector into the T2 slot (transducer slot) of the connector holder.
NOTE: The slots are keyed to prevent reversed installation, so be careful not to force the connector into the holder. See your
control head installation guide for additional information.
700 Series™ with Ethernet NOTE: If you are installing the Speed Sensor accessory (optional), insert the Sonar/Speed
Y-Cable connector into the T2 slot on the connector holder. Then, connect the transducer connector and speed sensor
connector to the corresponding connectors on the Y-Cable. The Y-Cable requires a separate purchase. Contact Customer
Service for details.
2. Turn on your control head.
connector holder
transducer switch
cable connector
Transducer_Switch_Install_531870-1_C.qxp:530511-2_A - TrollingMotor_IG_prfC.qxd
8/4/14
5:41 PM
Page 4
4
531870-1_C
Transducer Switch
5. Powering Off
It is important to make sure all accessories (switches, control heads, etc.) are
powered off in order to avoid possibly draining the battery. To make sure your
Transducer Switch is disengaged, follow the steps below.
If your Transducer Switch is connected to the fuse panel:
1. Power off your boat to disengage the switch.
If your Transducer Switch is connected to a battery switch:
1. Turn the dial of the battery switch to the OFF position.
If your Transducer Switch is connected directly to a battery:
1. Power off your boat.
2. Remove the Transducer Switch wires from the battery.
Contact Humminbird
Web site
E-mail
Telephone
Direct Shipping
humminbird.com
service@humminbird.com
1-800-633-1468
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING! This device should not be used as a navigational aid to prevent
collision, grounding, boat damage, or personal injury. When the boat is moving,
water depth may change too quickly to allow time for you to react. Always operate
the boat at very slow speeds if you suspect shallow water or submerged objects.
WARNING! Disassembly and repair of this electronic unit should only be
performed by authorized service personnel. Any modification of the serial number
or attempt to repair the original equipment or accessories by unauthorized
individuals will void the warranty.
WARNING! This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Johnson
Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating
in compliance with known and applicable environmental regulations, and a good
neighbor in the communities where we make or sell our products.
WEEE Directive: EU Directive 2002/96/EC “Waste of Electrical and Electronic
Equipment Directive (WEEE)” impacts most distributors, sellers, and
manufacturers of consumer electronics in the European Union. The WEEE
Directive requires the producer of consumer electronics to take responsibility for
the management of waste from their products to achieve environmentally
responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed and
intended as fixed or temporary installation in transportation vehicles such as
automobiles, aircraft, and boats. In some European Union member states,
these vehicles are considered outside of the scope of the Directive, and EEE
for those applications can be considered excluded from the WEEE Directive
requirement.
This symbol (WEEE wheelie bin) on product indicates the product
must not be disposed of with other household refuse. It must be
disposed of and collected for recycling and recovery of waste EEE.
Johnson Outdoors Marine Electronics, Inc. will mark all EEE products
in accordance with the WEEE Directive. It is our goal to comply in the
collection, treatment, recovery, and environmentally sound disposal of those
products; however, these requirements do vary within European Union
member states. For more information about where you should dispose of your
waste equipment for recycling and recovery and/or your European Union
member state requirements, please contact your dealer or distributor from
which your product was purchased.
1
Overview
Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read
these instructions carefully in order to get the full benefit from your Humminbird® accessory.
Transducer Switch
The Transducer Switch comes with all the necessary hardware to allow you to connect your control head to two
transducers. The transducers may be the same type of transducer with different mounting locations, or you can
maximize your unit’s performance by using two different transducers. The switch is intended for installation on the
console, and will work well on almost any boat.
Customer Service: If you find that any items are missing from your installation kit, visit our Web site at
humminbird.com or call Customer Service at 1-800-633-1468.
Supplies: In addition to the hardware supplied with your Transducer Switch, you will need a hand drill with various
size bits, a Phillips screwdriver, an adjustable wrench, and a 3 amp fuse.
Installation
Perform the procedures in the following sections to install the Transducer Switch on your boat. Before installing the
Transducer Switch, gather all the parts you will need, and make sure that the planned location of the Transducer
Switch will allow you to connect the two transducers to your control head.
1. Locating the Transducer Switch Mounting Position
Mounting the Switch
There are two ways to find the mounting location, as follows:
Switch Panel: If your console already contains a switch panel with an available slot, slide the Transducer Switch into
the designated slot until it snaps into place. Proceed to procedure two.
boat
console
In-Dash: If your console does not have a switch panel or a pre-made mounting location, you will need to create one
yourself.
To manually create a mounting location:
switch
1. Locate a suitable, flat area of the dash to mount the Transducer Switch. The switch requires a depth of at least
1.5 inches (38.1 millimeters). Make sure that it will be positioned near your control head on the console of the
boat, within reach of the cables for both transducers. Also, make sure you have access behind the panel in order
to attach the cables.
2. Tape the template (included) over the desired in-dash mounting location.
3. At a location inside the dotted line on the template, drill a hole large enough to insert the blade of the
reciprocating saw. Carefully begin cutting toward the dotted line, then follow the dotted line around the
template. Remove the template when finished.
4. Insert the end of the switch through the hole until it snaps securely in place.
2. Connecting the Transducers and the Control Head to the Switch
To connect your Transducer Switch to your control head, you may have to remove the control head from the Quick
Disconnect Mounting Bracket and temporarily disassemble the connector holder.
NOTE: Your connector holder hardware may be different than the illustration, depending on your Humminbird model. See
your control head installation guide for details.
CAUTION! Do NOT mount the cables where the connectors could be submerged in water or flooded. If cables are installed
in a splash-prone area, it may be helpful to apply dielectric grease to the inside of the connectors to prevent corrosion.
Dielectric grease can be purchased separately from a general hardware or automotive store.
© 2014 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
531870-1_C
Transducer Switch
CAUTION! Do not cut or shorten the transducer cables, and try not to damage the cable insulation. Route the cable as far
as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference. If the cable is
too short, extension cables are available to extend the transducer cable up to a total of 50 feet. For assistance, contact
Customer Service.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising