Supermicro CSE-743I-R760B, CSE-743S1-R760B, CSE-743S1-R760 Datasheet

Supermicro CSE-743I-R760B, CSE-743S1-R760B, CSE-743S1-R760 Datasheet
SC743 CHASSIS
USER'S GUIDE
1.1b
SC743 Chassis User’s Guide
The information in this User’s Guide has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates. Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGE ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.
Revision : 1.1b
Release Date: Jan. 3, 2006
Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.
Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.
Copyright © 2006 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
1-2
Chapter 1: Safety Information and Technical Specifications
Table of Contents
Chapter I: Safety Information and Technical Specifications .......... 1-4
1-1. Electrical Safety Guidelines ............................................................. 1-4
1-2. General Safety Guidelines ............................................................... 1-5
1-3. ESD Safety Guidelines ....................................................................... 1-6
1-4. Operation Safety Guidelines .......................................................... 1-6
1-5. Product Compliance Information ................................................. 1-8
1-6. The SC743 Series: Packing List and Specifications ............. 1-9
1-7. The SC743 Series: Packing List, Specifications & Back Panels
......................................................................................................................... 1-10
Chapter 2: Chassis Description and Installation Procedures ........ 2-1
2-1. Chassis Description ........................................................................... 2-1
A. Contents of the Accessory Kit ............................................................... 2-1
B. Chassis Front View and the Front Control Panel ................................ 2-2
C. Chassis Rear View and the Back Panel .............................................. 2-4
2-2. Chassis Installation ........................................................................... 2-6
A. Important Safety Guidelines ..................................................................... 2-6
B. Tools Needed .............................................................................................. 2-6
C. Accessing the SCA Drive Tray and Installing a Hard Drive .............. 2-7
D. Removing the Top Cover of the Chassis ............................................... 2-8
E. Accessing the Front Chassis Fans ........................................................ 2-9
F. Accessing the Power Supply ................................................................ 2-12
G. Installing the Motherboard ...................................................................... 2-13
H. Accessing the Interior between the Back Panel and the Mid-plane ......
......................................................................................................................... 2-15
I. Installing the PCI cards ............................................................................. 2-16
J. Installing 5.25" or 3.5" Devices ............................................................. 2-17
K. Installing the Air Shroud ........................................................................ 2-20
L. Installing the Chassis Rails ................................................................... 2-21
Addendum A: Installing the CSE-M34T Mobile Rack ....................... A-1
Addendum B: Installing the CSE-M35S/T1 Mobile Rack ................. B-1
1-3
SC743 Chassis User’s Guide
Chapter 1-Safety Information and Technical
Specifications
1-1 Electrical Safety Guidelines
!
Warning: To avoid electrical shock,
cords as follows:
check the power
Checking the Power Cords
zUse the exact type of power cords as required.
zBe sure to use power cord(s) that came with safety certifications.
zThe power cord(s) must be compliant with the AC voltage requirements in your
region.
zThe power cord plug cap must have an electrical current rating that is at least
125% of the electrical current rating of this product.
zThe power cord plug cap that plugs into the AC receptacle on the power
supply must be an IEC 320, sheet C13, type female connector.
zBe sure to disconnect the power supply before accessing the SC743 or its
components.
zPlug the Power cord(s) into a socket that is properly grounded before
turning on the power.
!
Warning: Follow the guidelines below to avoid possible
damage to the system or injury to yourself:
General Electrical Safety Guidelines
z Be aware of the locations of the power switches on the chassis and in the
room, so you can disconnect the power supply if an accident occurs.
z Take extra precautionary measures when working with high voltage
components. It is not recommended to work alone.
z Before removing or installing main system components, be sure to
disconnect the power first. Turn off the system before you disconnect
the power supply.
Use only one hand when working with powered-on electrical equipment to
avoid possible electrical shock.
1-4
Chapter 1: Safety Information and Technical Specifications
Use rubber mats specifically designed as electrical insulators when working
with computer systems.
The power supply or power cord must include a grounding plug and must
be plugged into grounded outlets.
Motherboard Battery: CAUTION -Make sure not to install the onboard battery
upside down to avoid possible explosion. Make sure that the positive side
is facing up on the motherboard. This battery must be replaced only with
the same or an equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
CD-ROM Laser: CAUTION - Do not open the enclosures of power supplies
or CD ROM to avoid injury.
1-2 General Safety Guidelines
!
Warning!!
Follow the guidelines below to avoid
possible damage to the system or injury to yourself:
Keep the area around the SC743 clean and free of clutter.
To avoid injuries to your back, be sure to use your leg muscles, keep your
back straight, and bend your knees, when lifting the system.
After removing the components or chassis covers from the system, place
them on a table for safeguard.
Avoid wearing loose clothing to preventing it from coming into contact with
electrical circuits or being pulled into a cooling fan.
The handles are for sliding the chassis in and out of the
racks only. Do not carry the chassis by the handles.
1-5
SC743 Chassis User’s Guide
1-3 ESD Safety Guidelines
!
Electric Static Discharge (ESD) can damage electronic components. To prevent damage to your system board, it is
important to handle it very carefully. The following measures are
generally sufficient to protect your equipment from ESD.
Use a grounded wrist strap designed to prevent static discharge.
Keep all components and printed circuit boards (PCBs) in their antistatic
bags until ready for use.
Touch a grounded metal object before removing the board from the antistatic bag.
Do not let components or PCBs come into contact with your clothing, which may
retain a charge even if you are wearing a wrist strap.
Touch a grounded metal object before removing the board from the antistatic
bag.
Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in
use.
For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting
fasteners and the motherboard.
1-4 Operation Safety Guidelines
Warning: For proper cooling, make sure to install all
chassis covers before turning on the system. If this rule is
not strictly followed, warranty may become void. Do not open
the casing of a power supply. Power supplies can only be
accessed and serviced by a qualified technician of the manufacturer.
!
1-6
Chapter 1: Safety Information and Technical Specifications
STOP
To avoid personal injury and property damage, please carefully
follow all the safety steps listed below:
Before accessing the chassis:
1. Turn off all peripheral devices connected to the SC743.
2. Press the power button to power off the system.
3. Unplug all power cords from the system or the wall outlets.
4. Disconnect all the cables and label the cables for easy identification.
5. Use a grounded wrist strap designed to prevent static discharge when
handling components.
Removing the chassis covers:
After completing the above steps, you can remove the covers and install
components/peripheral devices into the chassis as described in Chapter 2.
1. Unlock and remove the screws and fasteners to remove the cover or
components.
2. Save all the screws and fasteners for later use. (If necessary, label these
screws or fasteners for easy identification.)
3. Follow the instruction given in Chapter 2 to remove the chassis covers.
Reinstalling the chassis covers:
To maintain proper system cooling and airflow, do not operate the system
without installing all chassis covers back to the chassis. To reinstall the chassis
covers, please follow the steps listed below:
1. Make sure that all components and devices are securely fastened
on the chassis and there are no loose parts/screws inside the chassis.
2. Make sure that all cables are properly connected to the connectors and ports.
3. Use the original screws or fasteners to install the covers to the chassis.
4. Be sure to lock to the chassis or the system to prevent unauthorized access.
5. For proper cooling, enclose the chassis with covers before operating the
system.
1-7
SC743 Chassis User’s Guide
Before installing the chassis into a rack:
1. Make sure that the rack is securely anchored onto an unmovable surface or
structure before installing the chassis into the rack.
2. Unplug the power cord(s) of the rack before installing the chassis into the
rack.
3. Make sure that the system is adequately supported. Make sure that all the
components are securely fastened to the chassis to prevent components
falling off from the chassis.
4. Be sure to install an AC Power Disconnect for the entire rack assembly and
this Power Disconnect must be clearly marked.
5. The rack assembly shall be properly grounded to avoid electrical shock.
6. The rack assembly must provide sufficient airflow to the chassis for proper
cooling.
1-5 Product Compliance Information
The SC743 Chassis is compliant with the following safety standards/
requirements:
Product Safety
*Canada/USA--UL60 950-CSA60 950
*European Union--EN 60 950
*International--IEC 60 950
Electromagnetic Compatibility (EMC)-Emissions
*European Union--EN55022: 1994
*International--CISPR 22
*USA--Title 47 CFR, Part 15
Electromagnetic Compatibility-Immunity
*European Union--EN55024: 1998
*International--CISPR 24
Power Line Harmonics/Voltage Flicker
*European Union--EN61000-3-2/EN61000-3-3
*International--IEC61000-3-2
1-6 An important note to the user
All images and layouts shown in this manual were based upon the latest
chassis Revision available at the time of publishing. The chassis you’ve
received may or may not look exactly the same as the ones shown in this
manual.
1-8
Chapter 1: Safety Information and Technical Specifications
1-6A Packing List and Chassis Specifications for
the SC743S1/743i Series--Revision A
A1. The SC743S1/743i-R760(B) chassis contains the following:
Component
SCA 1” Drive Tray (*SC743S1 only)
IDE Drive Carriage (*SC743i only)
80mm Hot- Swap Chassis Fan
80mm Rear Chassis Fan (Hot Swap)
760 W Triple Redundant (2+1) Power
Supply
8-port SCSI Single-channel w/SAF-TE Back
plane (*SC743S1 only )
Fan Shroud
SCSI Cable (”9”) (*SC743S1 only )
Quantity
8
2
4
2
1
Part Number
CSE- PT17 (B)
CSE- PT31 (B)
FAN-0072
Fan-0073
PWS-0050
1
CSE-SCA-743S1
1
1
CSE- PT54
CBL-033-U320
A2. The SC743S1/743i-650(B) chassis contains the following:
Component
SCA 1” Drive Tray (*SC743S1 only)
IDE Drive Carriage (*SC743i only)
80mm Hot- Swap Chassis Fan
80mm Rear Chassis Fan (Hot Swap)
650W Power Supply
8-port SCSI Single-channel w/SAF-TE Back
plane (*SC743S1 only )
Fan Shroud
SCSI Cable (”9”) (*SC743S1 only )
Quantity
8
2
4
2
1
1
Part Number
CSE- PT17 (B)
CSE- PT31 (B)
FAN-0072
Fan-0073
PWS-0056
CSE-SCA-743S1
1
1
CSE- PT54
CBL-033-U320
A3. The SC743S1/743i-645(B) chassis contains the following:
Component
SCA 1” Drive Tray (*SC743S1 only)
IDE Drive Carriage (*SC743i only)
80mm Hot- Swap Chassis Fan
645W Power Supply
8-port SCSI Single-channel w/SAF-TE
Backplane (*SC743S1)
Fan Shroud
SCSI Cable (”9”) (SC743S1)
Quantity
8
2
4
1
1
Part Number
CSE- PT17 (B)
CSE- PT31 (B)
FAN-0074
PWS-0060
CSE-SCA-743S1
1
1
CSE- PT54
CBL-033-U320
B. The SC743S1/743i Accessory Box contains:
Component
AC Power Cords (*SC743S1/743i-R760(B) only)
AC Power Cord (*SC743S1/743i-650,645 only)
Motherboard Screws and Standoffs
HDD Screws
(*Note: Please refer to Page 1-13
tions.)
1-9
Qty
3
1
1 set
1 set
for the Power Supply Specifica-
SC743 Chassis User’s Guide
1-6B Packing List and Chassis Specifications for
the SC743S1/743i/SC743S2 Series--Revision B
A1. The SC743S1/743i/SC743S2-R760(B) chassis contains:
Component
SCA 1” Drive Tray (*SC743S1 only)
IDE Driv e Carri age (*SC743i onl y)
80mm Hot-Swap Chassis Fan
80mm Rear Chassis Fan (Hot Swap)
760 W Triple Redundant (2+1) Power
Supply
8-port SCSI Single-channel w/SAF-TE Back
plane (*SC743S1 onl y)
Fan Shroud (Rev. B)
SCSI Cable (”9”) (*SC743S1 onl y)
Quantity
8
2
4
2
1
Part Number
CSE-PT17 (B)
CSE-PT31 (B)
FAN-0072
Fan-0081
PWS-0050
1
CSE-SCA-743S1
1
1
CSE-PT54
CBL-033-U320
A2. The SC743S1/743i/SC743S2-650(B) chassis contains:
Component
SCA 1” Drive Tray (*SC743S1 only)
IDE Driv e Carri age (*SC743i onl y)
80mm Hot-Swap Chassis Fan
80mm Rear Chassis Fan (Hot Swap)
650W Power Supply
8-port SCSI Single-channel w/SAF-TE Back
plane (*SC743S1 onl y)
Fan Shroud (Rev. B)
SCSI Cable (”9”) (*SC743S1 onl y)
Quantity
8
2
4
2
1
1
Part Number
CSE-PT17 (B)
CSE-PT31 (B)
FAN-0072
Fan-0081
PWS-0056
CSE-SCA-743S1
1
1
CSE-PT54
CBL-033-U320
A3. The SC743S1/743i-645(B) chassis contains the following:
Component
SCA 1” Drive Tray (*SC743S1 only)
IDE Driv e Carri age (*SC743i onl y)
80mm Hot-Swap Chassis Fan
645W Power Supply
8-port SCSI Single-channel w/SAF-TE
Backplane (*SC743S1)
Fan Shroud (Rev. B)
SCSI Cable (”9”) (SC743S1)
Quantity
8
2
4
1
1
Part Number
CSE-PT17 (B)
CSE-PT31 (B)
FAN-0074
PWS-0060
CSE-SCA-743S1
1
1
CSE-PT54
CBL-033-U320
B. The SC743S1/743i/SC743S2 Accessory Box contains:
Component
AC Power Cords (*SC743S1/743i-R760(B) only)
AC Power Cord (*SC743S1/743i-650,645 only)
Motherboard Screws and Standoffs
HDD Screws
Qty
3
1
1 set
1 set
(*Note: Please refer to Page 1-13 for the Power Supply Specifications.)
1-10
Chapter 1: Safety Information and Technical Specifications
1-7A Packing List, Chassis Specifications and Back
Panels for the SC743T Series--Revision A
A1. The SC743T-760 (B) chassis contains the following:
Component
SCA 1” Drive Trays
80mm Hot- Swap Chassis Fan
80mm Hot-Swap Rear Chassis Fan
760W Triple Redundant (2+1) Power
8-port SATA Backplane
Fan Shroud
Qty
8
4
2
1
1
1
Part Number
CSEPT17(B)
FAN-0072
FAN-0073
PWS-0050
CSE-SATA-743
CSE- PT54
A2. The SC743T-650(B) chassis contains the following:
Component
SCA 1” Drive Trays
80mm Hot- Swap Chassis Fan
80mm Hot-Swap Rear Chassis Fan
650W Power Supply
8-port SATA Backplane
Fan Shroud
Qty
8
4
2
1
1
1
Part Number
CSEPT17(B)
FAN-0072
FAN-0073
PWS-0056
CSE-SATA-743
CSE- PT54
A3. The SC743T-645(B) chassis contains the following:
Component
SCA 1” Drive Trays
80mm Hot- Swap Chassis Fan
645W Power Supply
8-port SATA Backplane
Fan Shroud
Qty
8
4
1
1
1
Part Number
CSEPT17(B)
FAN-0074
PWS-0060
CSE-SATA-743
CSE- PT54
B. The SC743 Accessory Box contains:
Qty
3
1
1 set
1 set
4
1
Component
AC Power Cords (*SC743T-R760 (B) only)
AC Power Cord (*SC743T-650,645 only)
Motherboard Screws and Standoffs
HDD Screws
SATA Cable (CBL-0044)
SATA LED Cable (CBL-0077)
(*Note: Please refer to Page 1-13
tions.)
for the Power Supply Specifica-
1-11
SC743 Chassis User’s Guide
1-7B Packing List, Chassis Specifications and Back
Panels for the SC743T Series--Revision B
A1. The SC743T-760 (B) chassis contains the following:
Component
SCA 1” Drive Trays
80mm Hot-Swap Chassis Fan
80mm Hot-Swap Rear Chassis Fan
760W Triple Redundant (2+1) Power
8-port SATA Backplane
Fan Shroud (Rev. B)
Qty
8
4
2
1
1
1
Part Number
CSEPT17(B)
FAN-0072
FAN-0081
PWS-0050
CSE-SATA-743
CSE-PT54
A2. The SC743T-650(B) chassis contains the following:
Component
SCA 1” Drive Trays
80mm Hot-Swap Chassis Fan
80mm Hot-Swap Rear Chassis Fan
650W Power Supply
8-port SATA Backplane
Fan Shroud (Rev. B)
Qty
8
4
2
1
1
1
Part Number
CSEPT17(B)
FAN-0072
FAN-0081
PWS-0056
CSE-SATA-743
CSE-PT54
A3. The SC743T-645(B) chassis contains the following:
Component
SCA 1” Drive Trays
80mm Hot-Swap Chassis Fan
645W Power Supply
8-port SATA Backplane
Fan Shroud (Rev. B)
Qty
8
4
1
1
1
Part Number
CSEPT17(B)
FAN-0074
PWS-0060
CSE-SATA-743
CSE-PT54
B. The SC743 Accessory Box contains:
Component
AC Power Cords (*SC743T-R760 (B) only)
AC Power Cord (*SC743T-650,645 only)
Motherboard Screws and Standoffs
HDD Screws
SATA Cable (CBL-0044)
SATA LED Cable (CBL-0077)
(*Note: Please refer to the next page
cations.)
1-12
Qty
3
1
1 set
1 set
4
1
for the Power Supply Specifi-
Chapter 1: Safety Information and Technical Specifications
C. SC743 Power Supply Specifications
Power supply spec
SC743 series
Mfr. model #
Mfr. part #
Rated AC input voltage
Rated input frequency
Rated input current
SP762-TS(3xSP382-TS Models)
PWS-0050
100-240V AC
50-60 Hz
14A (115V)
8A (230V)
760W
4350 BUTs/Hr
Rated output power
Maximum rated BTU
Nominal DC output
+3.3V
+5V
+12V
-12V
+5V Standby
36A
36A
50A combined
1A
3.5A
(*Note: When connecting the 760W Power Supply to the Drive Backplane,
be sure to connect the power supply to the connectors labelled "PD", "PE"
and "PH" (with yellow/green stripes), and then, to the connector labelled
"PJ", colored in yellow/blue stripes.)
1-13
SC743 Chassis User’s Guide
D. SCSI 743 Back Panel (*SC743S1/SC743S2 Only)
D-1 Jumper Settings and Pin Definitions
Jumper
Default Setting
Note
JP19
Open
Buzzer Reset (*Note Below)
(*Note: Press the button on the front panel once to disable the
buzzer. If the buzzer has been disabled, please be sure to press the
button once again to re-enable the buzzer.)
D-2 Jumper Setting Locations
S UPER
R
SCA743S1
REV 1.00
DOORLOCK
1
1
RESET
A
1
+
1
+
+
+
+
+
+
+
JP19: BUZZER ENABLE
ON: ENABLE
OFF: DISABLE
+
+
+
+
GND
GND
+5V
+12V
GND
GND
D3: BUZZER
F
IPMB
IC
+
+
+
+5V
1
A.
B.
C.
D.
E/F
+
+
2
+
+12V
IN
1
1
+
ENABLE
E
D
C
B
Jumper 19
SCSI Connector
IPMB
I2C
12V PWR Connectors
Note1: By default, we connect four chassis fans to the drive backpanel.
Note2: When connecting the 760W Power Supply to the Drive Backplane, be
sure to connect the power supply to the connectors labelled "PD", "PE" and
"PH" (with yellow/green stripes), and then, to the connector labelled "PJ",
colored in yellow/blue stripes.
1-14
Chapter 1: Safety Information and Technical Specifications
D-3 SCSI (Super) GEM Driver Installation (*for Windows OS)
(*Note: This driver is not necessary for other Operating Systems. If
you have two SCA backplanes, you will need to install the driver
twice.)
The driver is located on the Super Micro motherboard driver CD or is
available for download from our FTP site: ftp://ftp.supermicro.com/driver/
Qlogic/
Follow the procedure below to install this driver to your system.
Installing
the driver:
1)
2)
3)
4)
5)
6)
Right click on “My Computer” and choose “Property”.
Select “Hardware” tab and click on “Device Manager”.
Open “Other Devices” or wherever “GEM318” is on.
Right click on this device and choose “Property”.
Click on “Driver” tab and choose “Update Driver”.
Click “Next” 2 times, uncheck both “Floppy disk drives” and “CD-ROM
drives”. Then, select the item- “Specify a location,” and choose
“Next”.
7) Click on “Browse” and choose D drive or wherever Supermicro Setup
CD is in.
8) Choose “Qlogic” folder and click on “Open”.
9) System will automatically detect GEM318 and install the drive from this
point on.
or,
1) Right click the "My Computer" icon on your desktop and choose
Properties.
2) Click on the Hardware tab and click on "Device Manager" to bring up
the list of system devices.
3) You may see one or two yellow question marks (?) that read QLogic
GEM354 or GEM318 SCSI Processor Device. Right click on these, and
choose to uninstall. If two such question marks are present, uninstall
both.
4) Click on Action tab and choose "Scan for Hardware Changes". The
Hardware Wizard program should start up. Click "Next".
5) At the first prompt, choose “Display a list of known device drivers for
the device so that I can choose a specific driver” and click "Next".
6) Choose “Other Devices” and click Next.
7) Choose “Have Disk”, and specify your floppy drive location in the
options box. Then, click "Next".
8) Highlight “Enclosure Services Device” and click "Next".
9) Ignore the warning prompt by clicking "Yes".
1-15
SC743 Chassis User’s Guide
E. SATA743 Back Panel (*SC 743T Only)
E-1 Jumpers and Default Settings
Jumper
Description
Default
JP18
Buzzer Reset
Open
*JP25
Overheat Temperature 50o C
1-2 (*Note 1)
*JP26
Common Act In and Act #0~#7 In
Open (*Note 2)
(*Note1: Test if the buzzer is beeping to see if the OH temperature is >=50o C
(*Note2: Test to see if all 8 Activity. LEDs, 8 HDDs, and CBL-0077 are working
properly.)
E-2 Connectors/Jumpers Pin Definitions
(*Note: Please refer to Diagram 1 on the next
page for Jumpers/Connectors locations.)
A1/A2. JP10/JP13: 4-Pin Power
Connectors
(*Refer to Table 1 on the right for pin
definitions.)
B. JP26: HDD Activity
(Refer to Table 2 on the right for pin
definitions.)
Table 1
4-pin PWR Connector
(JP10/JP13)
Pins # Definition
1
+12V
2 & 3 Ground
4
+5V
Table 2
HDD Activity Pin Definitions
(JP26)
Pin Number Definition Pin Number Definition
1
ACT0
6
ACT4
2
ACT1
7
ACT5
3
ACT2
8
ACT6
4
ACT3
9
ACT7
5
COM_ACT
10
Ground
Table 3
OH Temperature
(JP25)
Pins # Definition
Open
450C
1&2
500C
550C
2&3
C. JP25: Overheat Temperatures
(Refer to Table 3 on the right for pin
definitions.)
D. JP35: GEM424 Reset
E. JP18: Buzzer Reset
E-3 LED Indicators
LED Indicators
D5, D6, D7, D8, D19, D20, D23,
D26: SATA Slots (#0-#7 Fail)
D12, D13, D14, D15, D18, D21,
D22, D27: SATA Slots (#0-#7
Activity)
LED#
D5
D12
D6
D13
D7
D14
D8
D15
1-16
Function
FAIL0
ACT0
FAIL1
ACT1
FAIL2
ACT2
FAIL3
ACT3
LED#
D19
D18
D20
D21
D23
D22
D26
D25
Function
FAIL4
ACT4
FAIL5
ACT5
FAIL6
ACT6
FAIL7
ACT7
Chapter 1: Safety Information and Technical Specifications
E-4 Jumpers/Headers Locations
Diagram1: Jumpers and Connectors Locations
SATA743 REV. 1.01
1
MM1
JP18
1
C
M7
MT2
E
H5
JP35
JP25
MT1
H6
H12
D
+12V
GND GND +5V
J2
SATA0
J1
SATA1
SATA7
SATA6
JP13
A1
J3
SATA5
SATA4
SATA3
SATA2
SATA1
SATA0
SATA3
SATA5
SATA8
SATA7
JP10
J4
J9
SATA2
J11
J13
SATA4
J15
A2
+12V
GND GND +5V
+
H2
+
B
MT3
D5
Pin7
Pin8
Pin9
Pin10
Pin2
Pin3
Pin4
Pin5
Pin6
Pin1
Pin4
GND +5V
Pin3
Pin2
Pin1
GND
D12
B
A
+12V
D13
D6
D14
D7
D15
D8
D18
D19
D20
D21
D23
D22
D25
D26
JP26
A1/A2:JP1 0/JP13:
PWR Connectors
B:JP26: HDD ACT
1-17
SC743 Chassis User’s Guide
Notes
1-18
Chapter 2: Chassis Description and Installation Instructions
Chapter 2: Chassis Description and Installation
Procedures
2-1 Chassis Description
A. Contents of the Accessory Kit:
The following items are included in the Accessory Kit:
M/B
HDD
B
A
B. Flat head 6-32 x 5 mm [0.197]
A. Pan head w/ lock
6-32 x 4.5 mm [0.177]
DRIVE
B
D
B. Flat head 6-32 x 5 mm [0.197]
E
E. Round head M3 x 5 mm [0.197]
D. Pan head 6-32 x 5 mm [0.197]
RAIL
F
F.
G
I
H. Flat head M5 x 12 mm [0.472]
Flat head M4 x 4 mm [0.157]
I.
G. Round head M4 x 4 mm [0.157]
M/B STANDOFF
J
J.
H
M/B standoff, 6-32 to 6-32
2-1
Washer for M5
SC743 Chassis User’s Guide
B. Chassis Front View and the Front Control Panel
Chassis Front Panel
M
K
L
Front Panel I/O Device Definitions
K.
L.
M.
Hot-Swappable Drive Trays (8)
Floppy Drive Bay
5.25 Drive Trays (2)
Front LED
A
B
C
D
E
F
LED Button Definitions
A.
Power Button
B.
System Reset
C.
Power Indicator
D.
HDD Activity Indicator
E/F. LAN Indicators
H.
Power Failure Indicator
I./J
USB Ports
2-2
G
H
I
J
Chapter 2: Chassis Description and Installation Instructions
LED Button Descriptions
LED Button
Power
Color
Green
HDD Activity
Green
LAN Indicators
Green
Overheat/Fan Fail
Red
System Alert/
Power Failure
Red
Condition
On
Off
Blink
Off
On
Blink
Off
On
Blink
Off
On
Off
2-3
Description
System On
System Off
HDD Activity
No Activity
Linked
LAN Activity
Disconnected
System Overheat
Fan Fail
System Normal
1 or more PWR modules
failure
System Normal
SC743 Chassis User’s Guide
C. Chassis Rear View and the Back Panel
C
A
B
D
SC743 Chassis-Rev. A Rear View
Back Panel Devices
A.
B.
C.
D.
Power Supply Module
Back Panel I/O Ports
Rear System Fans
Full-size PCI Expansion Slots
C
A
B
D
SC743 Chassis-Rev. B Rear View
2-4
Chapter 2: Chassis Description and Installation Instructions
*I/O Back Panel
K
E
F
G
H
I
J
Back Panel I/O Port Definitions
E.
Keyboard & Mouse
F.
G.
H.
I.
J.
K.
USB Ports
COM/Video Ports
LAN1 & LAN2
Audio (Line-In: top, Line-out: bottom)
Microphone
Parallel Port
(*Note: The actual I/O Configuration of your system might be different
from the one shown above.)
Power Module LED Descriptions
Power Module
LED
Color Condition
Green
Amber
Off
2-5
Description
Power Supply DC On
Power Supply Standby
No AC Power to the system
SC743 Chassis User’s Guide
2-2 Chassis Installation
A. Important Safety Guidelines
STOP
This product shall only be accessed, assembled and serviced
by technically qualified personnel or technicians.
To avoid personal injury and property damage, please read all the information
provided in Chapter 1, and carefully follow all the Safety Guidelines listed before
accessing or servicing the SC743 or its components. For your convenience, some
Safety Steps are also listed below:
Safety Steps
Before accessing the chassis:
1. Turn off all peripheral devices and turn off the power supply connected to the
SC743.
2. Unplug all power cords from the system or the wall outlets.
3. Disconnect all the cables and label the cables for easy identification.
4. Use a grounded wrist strap designed to prevent static discharge when handling
components.
Removing the chassis covers:
After completing the above steps, you can remove the chassis covers and install
components and devices into the chassis as described in this chapter.
1. Unlock and remove the screws and fasteners to remove the cover or components.
2. Save all the screws and fasteners for later use. (If necessary, label these screws
or fasteners for easy identification.)
3. Follow the instructions given in this chapter to remove the chassis covers.
B. Tools needed
1.
2.
Phillips Screw Driver
Antistatic Strap (recommended)
2-6
Chapter 2: Chassis Description and Installation Instructions
C. Accessing the Hot-Swappable Drive Tray and Installing a
Hard Drive Disk
To install the Hot-Swappable drive into the chassis, you need to first remove the
Hot-Swappable drive tray from the chassis.
Procedures
1. Unlock and open the drive tray door as shown below:
2. Press the release tab located on the drive tray door to release the drive tray
from its locking position.
3. Pull the drive tray door downward and pull the Hot-Swappable drive tray out
from the chassis..
(*Note: The orientation of the
picture shown below is for
Rack Mount only.)
3
2a
2
2b
1
4. Mount a hard drive in the drive tray and make sure that all the screws
are securely fastened as shown below.
or
2-7
SC743 Chassis User’s Guide
D. Removing the Side Cover of the SC743 Chassis
Before installing any components, replacing chassis fans or accessing the
motherboard, you will first need to remove the side cover.
Procedures
1. Press the release tab to unlock the side cover.
2
1b
1a
2. Once the release tab pops open, push the cover toward the rear side and slide
it out from the chassis as shown above:
2-8
Chapter 2: Chassis Description and Installation Instructions
E-1. Accessing the Middle chassis fans
Before installing the motherboard in the chassis or accessing the motherboard,
you will need to remove the front/rear chassis fans, the air shroud from the
chassis and install the standoffs on the chassis.
Procedures
1. Press the release tab located on the left side of the middle chassis fan (when
facing the front side of the fan) to the right side to unlock the chassis fan.
2
1
2. While pressing the release tab, pull the fan module from the chassis.
(*Note: When installing the fan module into the chassis, be sure to push the fan
module into the fan module slot until you hear the click. *The click sound indicates that the fan module is securely locked in the chassis.)
2-9
SC743 Chassis User’s Guide
E-2. Removing the Air Shroud
Before installing the motherboard into the chassis, you will need to remove the
air shroud first.
Procedures
1. Press the release tab located on the back side of the middle chassis bracket
as shown below until you hear the click.
SC743 Chassis-Rev. A
1
2
3
SC743 Chassis-Rev. B
1
2
3
2. Press the release tab on the back side of the rear chassis fan to loosen it as
shown above.
3. Once the release tab is loosened, pull the air shroud from the chassis.
(*Note: When installing the air shroud into the chassis, be sure to align the air
shroud against the guide rails and gently push the air shroud into the chassis
until you hear the click. The click sound indicates that the air shroud is securely
locked in the chassis.)
2-10
Chapter 2: Chassis Description and Installation Instructions
E-3. Accessing the Rear Chassis Fans
Procedures
1. Locate the release tab on the top of the rear chassis fan as shown below.
Push the release tab down to unlock the rear chassis fan.
1
2
2. Once the rear chassis fan is unlocked, you can remove the fan from the
chassis as shown above.
(*Note: When installing the fan module into the chassis, be sure to push the fan
module into the fan module slot until you hear the click. *The click sound indicates that the fan module is securely locked in the chassis.)
2-11
SC743 Chassis User’s Guide
F. Accessing the 760W Triple Redundant Power Supply
(*Caution: Unplug the Power Cord before removing the Power
Supply!!)
Procedures
1. Locate the release tab on the left side of the power supply.
2. Push the release tab to the right to release the power supply from its locking
position as shown below:
1
2
3. Once the power supply module is released from its locking position, remove
it from the chassis.
3
Warning: Do not open the casing of a power supply.
Power supplies can only be accessed and serviced by a
qualified technician from the manufacturer.
2-12
Chapter 2: Chassis Description and Installation Instructions
G. Installing the Motherboard
Be sure to disconnect the power supply before accessing or installing the motherboard in the chassis. To install the motherboard, first, you will need to identify
the locations of the processor(s), mounting holes, retention brackets, and then,
install the correct type of standoffs, and heatsink retention brackets under the CPU
or on the motherboard before installing the motherboard into the chassis. (Refer
to Chapter 1 for Safety Guidelines.)
Procedures
1. Lay the chassis on a flat surface. Locate the mounting holes on the chassis
and install standoffs through the holes on the chassis.
SC743 Chassis-Rev. A
1
SC743 Chassis-Rev. B
1
2. Follow the standard procedures to install the I/O shield in the chassis. (*Note:
Install heatsink retention brackets if needed. Refer to your shipping package
for retention brackets and installation guides if any.)
(**Note: the motherboard shown above is for reference only!! The motherboard is not included in the SC743 shipping package.)
2-13
SC743 Chassis User’s Guide
SC743 Chassis-Rev. A
4
3
A
SC743 Chassis-Rev. B
4
3
A
3. Secure the motherboard to the chassis with Type A(6-32) screws as shown
above. (*Please refer to Page 2-1 Motherboard kit for the Type A screw.)
4. Secure the CPU heatsink mechanism to the motherboard.
(**Note: the CPUs and Heatsinks shown above are for reference only!! The
motherboard is not included in the SC743 shipping package.)
Warning: For proper cooling, please make sure that the air shroud and
all the chassis covers are installed before you operate the system. Out
-of -warranty damage can occur if this rule is not strictly followed.
Please refer to the next page for Air Shroud Installation.
2-14
Chapter 2: Chassis Description and Installation Instructions
H. Access to the Interior between the Back Panel and the MidPlane
For easy access to the interior between the Back Panel and the Mid-plane,
please follow the instructions below before installing components or cables
into this area.
Procedures
1. Remove the two screws as shown in the picture below.
2. Remove the three screws on the bottom of the bracket between the Back
Panel and the Mid-plane.
3. Use a screw driver to gently press the release tabs to unlock the Mid-plane.
4. Pull the Mid-plane forward (about 35 0) as shown in the picture; then, you will
be able to easily access the interior between the Back Panel and the Midplane.
SC743 Chassis-Rev. A
1
4
SC743 Chassis-Rev. B
1
4
2-15
SC743 Chassis User’s Guide
I. Accessing the PCI Slot Brackets to Install PCI Cards
After you've installed the motherboard into the chassis, you are ready to
install add-on cards, such as PCI cards into the chassis. Before installing PCI
cards, please follow the instructions below to access the PCI slot brackets.
Procedures
1. Locate the release tab on the top of PCI slot bracket.
AAa
2. Gently apply pressure at the middle of the release tab to unlock the PCI Slot
bracket as shown below:
3. Once the PCI slot bracket is unlocked, pull the release tab upward, and
remove the PCI slot bracket from the chassis.
4. Once the PCI slot bracket is removed from the chassis, you can install the
PCI Cards or other add-on cards into the PCI slot bracket.
5. Gently push the PCI slot bracket (with the PCI card or the add-on card
installed) into to the PCI slot and, then, push the middle of the blue button until
you hear the click as shown above. (*The click sound indicates that the PCI
bracket is securely locked into the chassis.)
2-16
Chapter 2: Chassis Description and Installation Instructions
J. Accessing the Storage Module to Install 5.25" Devices, 3.5" Devices
or Mobile Racks
(Notes;
1. The storage module can accommodate up to three 5.25" devices such as
CD drives, IDE drives, DVD, tape drives and floppy drives as shown on this
page. You can use any combination of 5.25" devices (up to 3 drives) in this
module.
2. The storage module can also accommodate up to five 3.5" devices. To
configure the module for the use of 3.5" devices, you need to rotate the module
90 degrees as shown on the next page.
3. You can also simply rotate the storage module 90 degrees and install the
storage module back to the chassis in order to use the SC743 as a tower.
4. You can also install Supermicro's Mobile Rack CSE-M34T or Mobile Rack
CSE- M35S/T1 into the SC743 chassis. To do so, you need to simply remove
the storage module and replace it with a Mobile Rack. For Mobile Rack Information or Installation Instructions, please refer to Addendum A, and Addendum B.)
2-17
SC743 Chassis User’s Guide
Procedures
1. Push the buttons on the top cover to unlock it. Once it is unlocked, push the
top cover out of the chassis.
2. Remove the screw from each chassis foot.
3. Use a flat head screw driver to gently pry the chassis foot out of the chassis.
SC743 Chassis-Rev. A
1
2
3
2
SC743 Chassis-Rev. B
1
2
3
2
2-18
Chapter 2: Chassis Description and Installation Instructions
SC743 Chassis-Rev. A
4
5
4. Locate the release tab on top of the storage module as shown below. Press
the release tab to unlock the storage module.
5. Once the storage module is unlocked, push the module out of the chassis.
SC743 Chassis-Rev. B
4
2-19
SC743 Chassis User’s Guide
To configure the storage module for 5.25" devices
3. Remove the 5.25" drive trays from the storage module, and then, remove the
screws and drive tray brackets from the drive trays.
4. Install 5.25" devices into the storage module. Then, install the module back
to the chassis. Make sure that module is securely locked into the chassis.
To configure the storage module to support 3.5" devices or Mobile Racks
3. Remove the storage module from its housing, and then, remove the screws
and module brackets from the storage module.
4. Install 3.5" devices into the storage module. Securely attach the module
brackets to the storage module. (If a mobile rack is used, attach the brackets to
the mobile rack.)
5. Then, install the storage module (or the mobile rack) back to the chassis.
Make sure that module is securely locked into the chassis.
2-20
Chapter 2: Chassis Description and Installation Instructions
K. Installing the Air Shroud
!
Warning: For proper cooling, please be sure to install the air shroud
and all the chassis covers before you operate the system.
Procedures
1. Locate the three guide rails on the reverse side of front fan panel as shown
below.
2. Align the air shroud with the guide rails and gently push the air shroud into the
chassis until both rear release tab and the front release tab are seated properly
and you hear the click.
SC743 Chassis-Rev. A
1
2a
2b
2a
2b
SC743 Chassis-Rev. B
2-21
SC743 Chassis User’s Guide
L. Installing the Chassis Rails
Please make sure that the chassis covers and chassis rails are installed on the
chassis before you install the chassis into the rack.
To avoid personal injury and property damage, please carefully
follow all the safety steps listed below:
Before installing the Chassis rails:
1. Enclose the chassis with chassis covers.
2. Unplug the AC power cord(s).
3. Remove all external devices and connectors.
Procedures to install inner rails on the chassis
1. Locate a pair of inner rails and two sets of screws (6 screws-each set) that are
included in the shipping package, and align the inner rails against the top and the
bottom of the chassis as shown below:
2. Install the inner rails onto the chassis by tightening the screws provided. Make
sure that the rails are flush against the edge of the chassis.
!
Warning!!
Follow the guidelines below to avoid possible
damage to the system or injury to yourself:
* The handles are for sliding the chassis in and out of the racks only. Do not
carry the chassis by the handles.
* Keep the area around the SC743 clean and free of clutter.
* To avoid injuries to your back, be sure to use your leg muscles, keep your back
straight, and bend your knees when lifting the system.
* After removing the components or chassis covers from the system, place them on
a table for safeguard.
* Avoid wearing loose clothing to preventing it from coming into contact with electrical
circuits or being pulled into a cooling fan.
2-22
Chapter 2: Chassis Description and Installation Instructions
Procedures to Install the Outer Rails
1. Locate two pairs of outer rails--each pair of outer e rails consist of one middle
rail, one end bracket and one end rail as shown below:
Middle Rail
End Rail
End Bracket
2. Insert the end bracket and the end rail into the middle rail and secure the
outer rail assembly with screws.
3. Install a set of outer rail assembly to one side of the racks, and install another
set of outer rail assembly onto another side of the racks.
4. Insert the inner rails, which are attached to the SC743 chassis, into the
openings of the outer rail assemblies, and gently push the chassis into the
racks. Make sure that the chassis is properly and securely installed in the racks.
Outer Rail
Assemblies
SC743
Chassis
Inner Rails
2-23
SC743 Chassis User’s Guide
Notes
2-24
Addendum A:
Installing the CSE-M34S/CSE-M34T
Mobile Rack
SC743 Chassis User's Guide
Table of Contents
1. Packaging List .................................................................................................... 3
2. Technical Specifications ................................................................................... 3
3. Jumper Settings ................................................................................................. 4
4. Hardware Installation Procedures ................................................................ 6
5. SCSI(Super) GEM Drive Installation Instructions for Windows OS .......... 8
A-2
Addendum A: Installing Mobile Rack-CSE M34S/T
CSE-M34S/CSE-M34T
Supermicro’s CSE-M34S/CSE-M34T Mobile Rack Series offers the cutting
edge technology with greater flexibility. The CSE-M34T supports four Serial
ATA hot-swap hard drives that yield an unparalleled storage capacity without compromising productivity by eliminating possible system downtime. The
CSE-M34S also accommodates four SCSI SCA 320/160 hard drives which
provide configuration flexibility and maximum data integrity.
1. Packing List
Please check to see if you have received all the items listed below:
*CSE-M34S/CSE-M34T Mobile Rack
*90mm-Exhaust Fan
*Screws:
Six (6) counts of 6-32 hex washer head screws
Eight (8) counts of M3 washer head screws
Eighteen (18 )counts of Pan head screws
*Drive Carrier Four (4)CSE-PT10 (-beige only)
(*For the CSE-M34T only)
*Serial ATA Backplane (CSESATA-M34)
*Four (4) Serial ATA Cables (CBL-0044)
*Serial ATA LED cable (CBL-0057)
(*For the CSE-M34S only)
*SCSI Backplane (CSESCA-002)
*SCSI cable (CBL-027-U320)
2. Technical Specifications
Occupancy
Capacity
Cooling
Subsystem
System
Monitoring
Three (3) 5.25" Drive Bays
Four (4) 1" SCA Ultra320/160 Hard Drives with
SAF-TE built-in (*CSE-M34S only)
Four (4) 1" Host Receptacle Connectors, SATA
hot-swap hard drives (*CSE-M34Tonly)
One (1) 90mm Exhaust Fan
Fan Fail Detection LED and Alarm
Overheat LED indication
Built-in Termination (*CSE-M34S only)
Dimension
(WxHxD)
147mm x 129mm x 230mm
(5.8 in x 5.0 in x 9.1 in)
Weight
Gross: 6.8lb (3.4 kg)
Chassis supported:
SC743
A-3
SC743 Chassis User's Guide
3. Jumper Settings
A. Jumper Settings for the CSE-M34S (SCSI):
Jumper
Description
Setting
JP14
Delay Start
Closed: Enable,
JP18
Buzzer Reset
Closed: Enable,
JP25
Overheat Temperature
Open: Disable (*Default)
Open: Disable (*Default)
Open: 50oC
1-2: 55oC (*Default)
2-3: 60oC
JP21
SCSI Termination
Closed: Enable (*Default),
JP24
SCSI ID Selection
1-2: SCSI IDs:0,1,2,3,4 (*Default)
Open: Disable
2-3: SCSI IDs:9,10,11,12,13
Jumper Locations
JP24
JP14 JP25
JP21
JP18
A-4
Addendum A: Installing Mobile Rack-CSE M34S/T
B. Jumper Settings for the CSE-M34T (SATA):
Jumper
Description
Setting
JP18
Buzzer Reset
JP25
Overheat Temperature
Closed: Enable,
Open: Disable (*Default)
Open: 45OC
1-2: 50OC (*Default)
2-3: 55OC
JP28
Fan Sense
JP26
Common Act#1-Act#4
JP27
Common Act In-Act#1
JP29
Common Act In-Act#2
JP30
Common Act In-Act#3
JP31
Common Act In-Act#4
JP32
Common Act Out
1-2: Enabled (if a fan is not present,
the alarm will sound) (*Default),
2-3: Disabled
Connect this header to CBL-0057
(SATA LED Cable)
Closed: Enable,
Open: Disable (*Default)
Closed: Enable,
Open: Disable (*Default)
Closed: Enable,
Open: Disable (*Default)
Closed: Enable,
Open: Disable (*Default)
Closed: Enable,
Open: Disable (*Default)
Jumper Locations
JP25
JP18
Channel #1
Channel #2
Channel #3
Channel #4
JP28
Activity LEDsPin Definitions
Act. LED 1
Act. LED 2
Act. LED 3
Act. LED 4
JP26
Channel 1
Channel 2
Channel 3
Channel 4
A-5
ACT1
JP26
ACT2
ACT3
ACT4
COM
Key
SC743 Chassis User's Guide
4. Hardware Installation Procedures
(*Notes: For the CSE-M34S: 1. SCSI IDs are assigned automatically by the
backplane. Do not set IDs manually on the drives. See the previous section
for SCSI ID jumper settings. 2. SCSI termination is enabled by default on the
SCSI backplane. 3. To install the CSE-M34 Mobile Rack into the SC743
chassis, please refer to Chapter 2 Section J on Page 2-17 to 2-19 for
installation instructions.)
A. Accessing Hot Swap Drives:
1. Push the release button and pull up the handle to release the
drive tray as shown below on the left:
2. Pull out drive trays as shown below on the right:
Pull up the
drive trays
Pull up the
handle
Push the release button
3. Mount a drive in a carrier and secure it with screws as shown
below:
Mount a drive
into a carrier
Secure the drive
with screws
A-6
Addendum A: Installing Mobile Rack-CSE M34S/T
B. Accessing the Drive Backplane:
1. Remove the two screws as shown below:
Remove the
screws
The CSE-M34T (SATA) Model
The CSE-M34S(SCSI) Model
2. Pull out the rear fan bracket as shown below:
Pull out the rear
fan bracket
The CSE-M34S(SCSI) Model
The CSE-M34T(SATA) Model
3. Remove the six backplane screws and access the backplane as
shown below:
Remove the screws
A-7
Access the backplane
SC743 Chassis User's Guide
5. SCSI (Super) GEM Driver Installation Instructions for
Windows OS
Please refer to the following instructions to install
Driver for the Windows OS systems.
the SCSI GEM
(*Note: This driver is not necessary for other Operating Systems. If you
have two SCA backplanes, you will need to install the driver twice.)
The driver is located on the Super Micro motherboard driver CD or is available
for download from our ftp site: ftp://ftp.supermicro.com/driver/Qlogic/
Follow the procedure below to install this driver to your system.
Installing the driver:
1) Right click on “My Computer” and choose “Property”.
2) Select “Hardware” tab and click on “Device Manager”.
3) Open “Other Devices” or wherever “GEM318” is on.
4) Right click on this device and choose “Property”.
5) Click on “Driver” tab and choose “Update Driver”.
6) Click “Next” 2 times, uncheck both “Floppy disk drives” and “CD-ROM
drives”. Then, select the item- “Specify a location,” and choose “Next”.
7) Click on “Browse” and choose D drive or wherever Supermicro Setup CD
is in.
8) Choose “Qlogic” folder and click on “Open”.
9) System will automatically detect GEM318 and install the drive from this
point on.
or,
1) Right click the "My Computer" icon on your desktop and choose Properties.
2) Click on the Hardware tab and click on "Device Manager" to bring up the
list of system devices.
3) You may see one or two yellow question marks (?) that read QLogic
GEM354 or GEM318 SCSI Processor Device. Right click on these, and
choose to uninstall. If two such question marks are present, uninstall both.
4) Click on Action tab and choose "Scan for Hardware Changes". The
Hardware Wizard program should start up. Click "Next".
5) At the first prompt, choose “Display a list of known device drivers for the
device so that I can choose a specific driver” and click "Next".
6) Choose “Other Devices” and click Next.
7) Choose “Have Disk”, and specify your floppy drive location in the options
box. Then, click "Next".
8) Highlight “Enclosure Services Device” and click "Next".
9) Ignore the warning prompt by clicking "Yes".
A-8
Addendum B
Installing the CSE-M35S/CSEM35T1
Mobile Rack
SC743 Chassis User's Guide
Table of Contents
1.
Packaging List ...................................................................................................... 3
2.
Technical Specifications .................................................................................... 4
3.
Jumper Settings ................................................................................................... 5
4.
Installation Procedures ..................................................................................... 7
B-2
Addendum B: Installing Mobile Rack-CSE M35S/T1
CSE-M35S/CSE-M35T1
Supermicro’s CSE-M35S/CSE-M35T1 Mobile Rack Series offers the cutting
edge technology with greater flexibility. The CSE-M35T1 supports five Serial ATA hot-swappable hard drives that yield a unparalleled storage capacity without compromising productivity by eliminating possible system downtime. The CSE-M35S also accommodates five SCSI SCA 320/160 Hard
drives which provide configuration flexibility and maximum data integrity.
1. Packing List
Please check to see if you have received all the items listed below:
*CSE-M35S/CSE-M35T1 Mobile Rack
*90mm-Exhaust Fan (Fan-0057)
*Screws:
Thirteen (13) counts of Flat Head Screws
Twenty-four (24) counts of Round Head Screws
Seven (7) counts of Round Head Screws with Lock-Washer
*Drive Carrier Five (5)CSE-PT17/CSE-PT17(B)(-black)
(*For the CSE-M35T1 only)
*Serial ATA Backplane (CSE-SATAM35)
*Five (5) Serial ATA Cables (CBL-0044)
*Serial ATA LED cable (CBL-0057)
(*For the CSE-M35S only)
*SCSI Backplane (CSE-SCAM743)
*SCSI cable (CBL-027-U320)
B-3
SC743 Chassis User's Guide
2. Technical Specifications
Occupancy
Capacity
Cooling
Subsystem
System
Monitoring
Dimension
(WxHxD)
Weight
Three (3) 5.25" Drive Bays
Five (5) 1" SCA Ultra320/160 Hard Drives with SAF-TE
built-in (*CSE-M35S only)
Five (5) 1" Host Receptacle Connectors, SATA hot-swap
hard drives (*CSE-M35T-1 only)
One (1) 9cm Exhaust Fan
Fan Fail Detection LED and Alarm
Overheat LED indication
Drive Fail Alarm and Indication (*CSE-M35S only)
Built-in Termination (*CSE-M35S only)
146mm x 129mm x 245mm
(5.7 in x 5.0 in x 9.6 in)
Net: 5.9lb (2.9 kg), Gross: 7.5lb (3.7 kg)
Chassis supported:
SC743
B-4
Addendum B: Installing Mobile Rack-CSE M35S/T1
3. Jumper Settings
A. Jumper Settings for the CSE-M35S (SCSI):
Jumper
JP18
Description
Buzzer Reset
JP21
SCSI Termination
JP24
SCSI ID Selection
JP29
GEM 318 IDs
JP30
Fan Sense
Setting
Closed: Enable,
Open: Disable (*Default)
Closed: Enable (*Default),
Open: Disable
1-2: SCSI Ids: 0,1,2,3,4 (*Default),
2-3: SCSI Ids: 9,10,11,12,13
1-2: ID6 (*Default),
2-3: ID8
Pins 1-2: Enable (*Default) (If a fan
is not present, the alarm will
sound.),
Pins 2-3: Disable
Location of Jumpers
JP30
JP21
Pin 1
Pin 1
Pin 1
Pin 1
JP29
Pin 1
JP18
JP24
B-5
SC743 Chassis User's Guide
B. Jumper Settings for the CSE-M35T1 (SATA):
Jumper
Description
Setting
JP18
Buzzer Reset
JP25
Overheat Temperature
Closed: Enable,
Open: Disable (*Default)
Open: 45OC
1-2: 50OC (*Default),
2-3: 55OC
JP26
Act#1-Act#5
Connect this header to CBL-0057
(SATA LED Cable)
JP28:
Fan Sense
1-2: Enabled (if a fan is not present,
the alarm will sound) (*Default)
2-3: Disabled
Location of Jumpers
Pin 1
Pin 1
Channel #1
Channel #5
Channel #2
Channel #4
JP26
COM
ACT8
ACT4
ACT7
ACT3
ACT6
ACT2
ACT5
ACT1
Channel #3
Activity LEDsPin Definitions
Act. LED 1
Act. LED 2
Act. LED 3
Act. LED 4
Act. LED 5
JP18
FAN
JP28
JP25
Key
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
B-6
Addendum B: Installing Mobile Rack-CSE M35S/T1
4. Installation Procedures
(*Note:
For the CSE-M35S:
1. SCSI IDs are assigned automatically by the backplane. Do not set IDs
manually on the drives. See the previous section for SCSI ID jumper settings.
2. SCSI termination is enabled by default on the SCSI backplane.
3. To install the CSE-M35 Mobile Rack into the SC743 chassis, please
refer to Chapter 2 Section J on Page 2-17 to 2-19 for installation instructions.
A. Accessing Hot Swap Drives:
1. Push the release button located beside the drive LEDs (as
shown below:)
B-7
SC743 Chassis User's Guide
2. Swing the handle outward and pull out the unit (as shown below:)
3. Mount a drive in a carrier (as shown below:)
B-8
Addendum B: Installing Mobile Rack-CSE M35S/T1
B. Accessing the Exhaust Fan:
1. Push the tabs located on both sides of the unit (as shown below:)
2. Pull out the fan (as shown below:)
(*Note: For the SC-743 Chassis, the CSE-M35 Rear Exhaust Fan
should not be used. Instead, the hot-swap 120mm Chassis Fans
included with the SC-743 Chassis should be connected to the Backplane of the CSE-M35S/CSE-M35T1 Mobile Rack.)
B-9
SC743 Chassis User's Guide
C. Accessing the Drive Backplane:
1. Unscrew the screw located on the side of the unit (as
below:)
2. Pull out the Rear Bracket (as shown below:)
3. Access the Backplane (as shown below:)
B-10
shown
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement