Child Restraint
Secure Kid™
Child Restraint
Owner’s Manual
Keep for future use
Child Restraint System
Exclusive RightFit Belt Path
Child Requirements
Harness Use
10 to 29.4 kg
(22 to 65 lbs)
71 to 127 cm
(28 to 50 in.)
Booster Use
18 to 49.8 kg
(40 to 110 lbs)
110 to 145 cm
(43.3 to 57 in.)
Para instrucciones en Español,
llamar al: 1-800-233-5921
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2014 Evenflo Company, Inc.
25700307
11/14
More children are killed every year as passengers in
car crashes than by any other type of injury.
To reduce the risk of SERIOUS INJURY or DEATH, read
this owner’s manual and your vehicle owner’s manual
before installing and using this child restraint. Using a
child restraint makes a big difference. By properly using
this child restraint and following these instructions (and
the instructions that accompany your vehicle), you will
greatly reduce the risk of serious injury or death to the
child from a crash. Do not be misled by the commonly
used term “safety seat”; no restraint system can prevent
all injuries in all crashes. Many properly restrained
adults and children are injured in motor vehicle crashes,
including relatively minor crashes. A properly used child
restraint is the best way to minimize injuries to the child
and to increase the chances for the child’s survival in
most crashes.
U.S. REGULATORY NOTICE
This child restraint meets all applicable requirements of
Federal Motor Vehicle Safety Standard 213.
CANADIAN REGULATORY NOTICE
(Model numbers ending in “C.”)
This child restraint meets all applicable requirements of
Canadian Motor Vehicle Safety Standards CMVSS 213
and 213.2.
• No restraint can guarantee absolute protection from
injury in every crash.
• This child restraint is designed for use by children in
forward-facing and booster modes.
To use this child restraint properly, children MUST
meet weight/size specifications as follows:
For 5-pt Harness Use
• The child weighs 10 – 29.4 kg (22 – 65 lbs)
• The child is 71 – 127 cm (28 – 50 in.) AND
the tops of their ears are at (or below) the child
restraint headrest.
• Child is one year old or older.
For Booster Use
• The child weighs 18 – 49.8 kg (40 – 110 lbs)
• The child is 110 – 145 cm (43.3 – 57 in.) tall
AND the tops of their ears are below the child
restraint headrest.
• Child is four years old or older.
Table of Contents
Important Information
Warnings .................................................................. 2
Safe Practices ........................................................... 7
Recall Information for U.S. Customers ....................... 8
Public Notice for Canadian Customers ..................... 8
Motor Vehicle / Aircraft Usage .................................. 8
LATCH Information .................................................. 9
Care and Cleaning ................................................... 9
Visual Glossary ....................................................... 10
Using the Internal 5-pt Harness
Installation Checklist .............................................. 13
Installation with Lower Anchor Connectors ............ 14
Which Type of Lower Anchor Connector is on Your
Child Restraint? ................................................... 15
Installation with Lower Anchor Hooks ..................... 15
Installation with SureLatch Connectors ................... 18
Installation with Quick Connectors ......................... 22
Installation with Vehicle Seat Belt ........................... 25
Securing the Child ................................................. 28
Removing the Child ............................................... 30
Positioning the Harness Strap ................................. 31
Positioning the Crotch Strap .................................. 33
Using a Booster Seat
When to Put Your Child in a Booster Seat ............... 34
Booster Installation Checklist .................................. 37
Converting into a Booster Seat ............................... 38
General Information
Leveling the Booster Seat ........................................ 42
Booster Seat Belt Routing .........................................42
Using the SureLatch Connectors ............................ 43
Using the Quick Connectors ................................... 43
Using the Latch Hook Connectors ........................... 43
Using the TruTether Adjuster .................................. 44
Adjusting the Headrest ........................................... 45
Removing Seat Pad ................................................ 45
Removing Headrest Pad ......................................... 45
Securing Your Child Restraint in Aircraft .................. 46
Installing Child Restraint in Aircraft .......................... 47
Replacement Parts .................................................. 48
Limited Warranty .................................................... 50
1
Symbol Legend
Airbag Symbol – Alerts you to important
information about airbag safety.
LATCH Symbol – Alerts you to important
information about LATCH safety.
Tether Anchor Symbol – Alerts you to
important information about tether anchor safety.
WARNING
Air Bag Warnings
• DO NOT use this restraint in the front seat of a vehicle
equipped with an air bag. Air bags may cause serious
injury or death to children 12 years of age and under.
If your vehicle has an air bag, refer to your vehicle
owner’s manual for child restraint installation.
• If the rear seat of your vehicle is equipped with side
air bags, refer to the following information for proper
usage.
Vehicles built prior to the 2002 model year:
DO NOT use this restraint in a vehicle seating position
equipped with a side air bag unless authorized by the
vehicle manufacturer.
Model year 2002 and newer vehicles:
Refer to your vehicle owner’s manual before placing
this restraint in a seating position equipped with a side
air bag.
• DO NOT place any objects between the restraint and
the side air bag, as an expanding air bag may cause
the items to strike the child.
The back seat is the safest place for
children 12 and under.
2
WARNING
General Warnings
• Failure to follow installation instructions can result in
the child striking the vehicle’s interior during a sudden
stop or crash. Serious injury or death may result.
These instructions and the instructions in your vehicle
owner’s manual must be followed carefully. If there is a
conflict between the two, the vehicle owner’s manual
regarding child restraint installation must be followed.
• NEVER leave child unattended.
• DO NOT use child restraint if it is damaged, broken, or
missing parts.
• DO NOT use this restraint if it has been involved in a
crash. It must be replaced.
• NEVER use this child restraint without the headrest
installed.
• NEVER use this child restraint rear-facing.
Location Warnings
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• According to statistics, children are safer when properly
restrained in a rear seating position than in the front
seating position. Generally, the center rear position is
safest and should be used if available.
• Some child restraints do not fit all vehicles or all seating
locations. There are many thousands of combinations
of vehicle makes, models, child restraint configurations,
seat belt designs, and seat cushion shapes.
The easiest way to determine whether the child
restraint is suitable for a particular seating position is
to check for a tight installation. If the child restraint
can not be properly installed, DO NOT use the child
restraint. Consult vehicle owner’s manual, try a different
seating location or call Evenflo.
• ONLY use this child restraint on forward-facing
vehicle seats. DO NOT use this restraint with vehicle
seats that face the rear or side.
• ONLY use this child restraint on vehicle seats with
backs that lock into place.
3
WARNING
Forward-facing Position Warnings
• If the child weighs more than 29.4 kg (65 lbs) or their
shoulders are above the highest harness level, you
MUST use this child restraint as a booster (p. 34).
• Adjust, or remove, the vehicle headrest, in the seat
where the child restraint is to be fastened, so that
the back of the child restraint rests against the vehicle
seat back.
• The headrest on the vehicle seat in front of the child
should be put in its lowest position. The vehicle seat
back that the child faces must be fully padded and
free of any hard objects.
Seat Belt Warnings
For 5-point Harness Use Only
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) forward or side-to-side at the vehicle
belt path. Serious injury or death may result from poor
installation. If you can not tightly secure the child
restraint, try again or move it to another location.
For Both 5-point Harness and Booster Use
• DO NOT use this child restraint in a vehicle with
door-mounted seat belts.
• DO NOT use this child restraint in a vehicle with seat
belts that automatically move along the vehicle frame
when the door is opened. These seat belts will not
hold a child restraint properly.
• DO NOT use this child restraint in a vehicle equipped
with lap belts that only lock during a sudden stop or
crash (emergency locking retractor – ELR). You must
use a seating location with a locking seat belt. Check
your vehicle owner’s manual to see if you have lap
belts with ELRs.
• If the vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect the child
in a crash.
• DO NOT allow the seat belt release button to touch
the child restraint. Accidental contact may cause the
seat belt to release. If necessary, turn the seat belt
release button away from the child restraint or move
the child restraint to a different location.
• Failure to adjust the harness or vehicle seat belts
snugly around the child may result in the child
striking the vehicle’s interior during a sudden stop
or crash. Serious injury or death may occur.
4
WARNING
Seat Belt Warnings
For Booster Use Only
• When using this booster seat, NEVER use a lap belt only.
You MUST use vehicle seat belts that have a
lap/shoulder combination.
• The shoulder belt MUST be threaded through the
shoulder belt guide (p. 36).
• DO NOT use this booster seat if the child’s ears are
above the back of the booster seat headrest.
• The shoulder belt MUST NOT cross the child’s neck
or fall off the child’s shoulder. If you can not adjust
the shoulder belt to properly lay midway between
the child’s shoulder and neck AND at or above the
shoulder, try another seating location or do not use
the booster seat.
LATCH Warnings
For 5-point Harness Use Only
• Do not use the lower anchors of the child restraint
anchorage system (LATCH system) to attach this child
restraint when restraining a child weighing more than
22.6 kg (50 lbs) with the internal harnesses of the
child restraint.
• This LATCH system is intended to be used ONLY as
described in these instructions. Serious injury or death
may result from misuse.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the
child restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• NEVER attach two lower anchor connectors to one
vehicle lower anchor bar.
• NEVER use the vehicle seat belts when using the lower
anchor connector assembly. Using both together can
cause slack in a sudden stop or crash.
• When not in use, the lower anchor connector
assembly should be securely stored on child restraint.
Keep out of reach of children.
5
WARNING
LATCH Warnings – cont.
For 5-point Harness Use Only
• ALWAYS be sure that the lower anchor connectors are
attached to the vehicle lower anchor bars by pulling
hard on the lower anchor connectors. If they are not
attached, the lower anchor connector assembly will
not secure your child restraint. Serious injury or death
may result.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at the
belt path on the child restraint. Serious injury or death
may result from poor installation. If you cannot tightly
secure the child restraint, try again or move it to
another location.
Tether Strap Warnings
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess or unused tether strap and secure with
a rubber band. Attach the tether hooks to the storage
clips when not in use (p. 11). This will keep an unused
tether from hitting someone during a crash.
Additional Warnings
• In hot or sunny weather, ALWAYS check the areas of
the child restraint that may contact your child (e.g.,
buckle, buckle tongues, etc.) for hot areas before
placing him/her into the child restraint. The child
could be burned. Cover the child restraint with a light
colored blanket when you leave the vehicle.
• This child restraint must be securely fastened to the
vehicle, even when unoccupied, using the vehicle
seat belts or lower anchor connectors. An unsecured
child restraint may injure someone if a crash occurs.
• DO NOT use the cup holders to store cans or hard
cups. Only for use with soft cups (such as styrofoam
or paper).
• DO NOT place any cups that contain hot liquids in the
cup holders.
• DO NOT attach additional padding, toys, or other
devices not made by Evenflo or described in these
instructions for the child restraint. Items not tested
with the child restraint could injure the child.
6
WARNING
Additional pads or pillows may interfere with the
function of the harness system, or cause breathing
problems if the child’s head falls forward, increasing
the risk of serious injury or death.
• Failure to follow installation instructions could result
in serious injury or death. These instructions and the
instructions in your vehicle owner’s manual must
be followed carefully. If there is a conflict between
the two, the vehicle owner’s manual regarding child
restraint installation must be followed.
• In cold weather, DO NOT dress the child in bulky
clothing like snowsuits if the child is riding in a child
restraint. Bulky coats/snowsuits make it difficult to
tighten the harness to the child, which may allow the
child to be ejected from the restraint during a crash.
If necessary, place a blanket over the harnessed child
without interfering with the child restraint harness
system.
Safe Practices
• Everyone rides buckled up or the vehicle does
not go. Make no exceptions for adults or children.
If someone unbuckles, stop the vehicle. Being firm
and consistent from the start will mean fewer discipline
problems as children get older. An unrestrained person
can be thrown into and injure other passengers.
• NEVER try to tend to a crying baby’s needs while
driving. NEVER take a baby out of a child restraint for
comforting while the vehicle is moving.
• DO NOT allow a child in a vehicle to have objects
such as lollipops or ice cream on a stick. The object
can injure the child if the vehicle swerves or hits a
bump.
• DO NOT feed an infant who is riding in a child
restraint.
• Put sharp or heavy items in the trunk. Anything loose
can be deadly in a crash.
7
Recall Information for U.S. Customers
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a
recall. Send your name, address, the restraint’s
model number, and manufacturing date to Evenflo
Company, Inc., 1801 Commerce Dr., Piqua, OH
45356 or call 1-800-233-5921. You may also register
on-line at:
www.evenflo.com/registercarseat
• For recall information, call the U.S. Government’s
Vehicle Safety Hotline at 1-888-327-4236
(TTY:1-800-424-9153), or go to:
www.NHTSA.gov
Public Notice for Canadian Customers
• To register your child restraint, return your registration
card, call 1-937-773-3971, or register on-line at:
www.evenflo.com/registercarseatcanada
• For recall information, call Transport Canada at
1-800-333-0510 (1-613-993-9851 in Ottawa region)
or Evenflo at 1-937-773-3971.
Motor Vehicle/Aircraft Usage
When used with the 5-point harness system and
properly installed pursuant to these instructions,
this restraint is certified for use only in
passenger and multi-purpose
passenger motor vehicles,
Check with
buses, and trucks equipped
your airline before
departure to make sure
with Type I or II seat belts and
this restraint meets
in aircraft.
TIP!
LATCH Information
“LATCH” (Lower Anchors and Tethers for CHildren) is a
system for attaching the child restraint to your vehicle
seat. It can be used in place of the seat belts in vehicles
with LATCH anchors. Refer to your vehicle owner’s
manual for the locations of LATCH anchors. Note: Your
vehicle owner’s manual may refer to this system as
”ISOFIX” or “Universal Anchorage System (UAS).”
Care and Cleaning
• DO NOT lubricate or immerse the LATCH connectors,
the buckle, or any part of this child restraint.
• Plastic and metal parts may be wiped clean with
mild soap and water and dried with a soft cloth.
Do not use abrasive cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and
water. Allow harness to air dry. DO NOT immerse
buckle in water.
• Machine wash the seat pad separately in cold water,
delicate cycle, and tumble dry 10 – 15 minutes on
low heat.
• NEVER use child restraint without the seat pad.
TIP!
To help protect the
vehicle upholstery, place a
towel beneath and behind
the child restraint.
their requirements.
When used without the
5-point harness system (in booster
mode) and properly installed pursuant to these
instructions, this restraint is certified for use only in
passenger and multi-purpose passenger motor vehicles,
buses, and trucks equipped with Type II seat belts. In
booster mode, this restraint is NOT certified for aircraft
use. A belt-positioning booster requires the use of a lap/
shoulder belt system, which is not available on aircraft.
Refer to pages 46 to 47 for instructions on installing your
child restraint in aircraft.
8
Manufactured in Fabriqué en
(year-month-day) (anné-mois-jour)
Name / Nom
Model / Modéle
Made in / Fabriqué en
Expires on/Expire le
For future reference, record the model number of your child
restraint AND the date of manufacture below.
Model Number:
Date of Manufacture:
9
Visual Glossary
Visual Glossary
Your vehicle components may be significantly different than
pictured. Consult your owner’s manual to help you identify your
vehicle components.
Rear
Headrests
Fold-down Armrest
Consult your vehicle’s
owners manual.
Front
Headrests
10
Back Seat
Belt Buckles
NO coloque el asiento infantil orientado
hacia atrás en el asiento delantero con
bolsa de aire.
Puede causar MUERTE o LESIONES GRAVES.
El asiento trasero es el lugar más seguro para
los niños de 12 años de edad y menores.
A
IR
B
A
G
Center Lap
Belt
Back Seat
Belt
Retractor
Lap/
Shoulder
Belt
IMPORTANT
Vehicle Lower
Anchor Bars
Seat Crease
Front Seat
Retractor
IMPORTANT: If your vehicle has side air bags, please refer to the
warnings on page 2.
Consult your vehicle
owner’s manual to determine
proper placement of child restraint
in your vehicle and familiarize
yourself with your vehicle’s
components.
Headrest
Headrest
Shoulder Belt
Guide
Model Number &
Date of Manufacture
Chest Clip
Cup Holder*
Lower Belt
Path Guide*
Lower Belt
Path Guide*
Cup Holder*
Harness
Release
Button
* Not available on all models.
10
(Shown fastened to
storage clip)
Tether Strap
Adjuster
SureLatch
Connector*
Tether Strap
Adjuster
Upper Belt Path
LATCH Guide
Harness
Adjust Strap
Tether Strap and Hook
(Push Button Release)
OR
Instructions
Buckle
5-pt Harness
Straps
4
30
20
120
Tether Anchors
Forward-facing
ONLY
Front Seat Lap
and Shoulder Belts
Splitter Plate
(Lever Release)
SureLatch
Connector*
Upper Belt Path
LATCH Guide
* Not available on all models.
11
Using the Internal
5-pt Harness
Installation Checklist
1. Secure child restraint to the vehicle seat.
Weight: 10 – 29.4 kg (22 – 65 lbs)
Height: 71 – 127 cm (28 – 50 in.)
AND the tops of the child’s ears are at,
or below, the child restraint headrest.
Age: At least one year old
IMPORTANT
Evenflo strongly recommends using the top
anchorage (tether) strap when using this seat
with the internal harness. Using the tether strap
will improve the stability of the child restraint
and may reduce the risk of injury.
Tether Strap
the child restraint is securely installed with one
of the following methods through the upper
belt path:
• *LATCH Hooks (p. 15)
• *SureLatch Connectors (shown at left) (p. 18)
• *Quick Connectors (p. 22)
• Vehicle Seat Belt (p. 25)
aIf the child weighs MORE than 22.6 kg
(50 lbs), the child restraint is securely installed
with the VEHICLE SEAT BELT ONLY (not LATCH)
through the upper belt path (p. 25).
aTether strap is attached and tightened (p. 17, 21,
24, or 27).
Using with the 5-pt Harness
aLocking clip is installed, if necessary (p. 26).
aIf the child weighs 22.6 kg (50 lbs) or LESS,
Child Requirements
2. Place the child in the child restraint.
aThe child’s back and bottom are flat against the
The 5-pt Harness
straps are at, or
slightly above, the
child’s shoulders.
back and bottom surfaces of the child restraint.
aThe tops of the child’s ears MUST be at, or below,
the top of the child restraint headrest.
3. Make necessary adjustments.
aCrotch strap is properly positioned (p. 33).
4. Fasten both buckle tongues. Refer to page 28.
5. Tighten Harness - Position and connect
chest clip.
aHarness straps are snug against the child’s
shoulders, with no slack (p. 29).
aChest clip MUST be at armpit level (p. 29).
6. Check your work.
aTo properly protect the child, the child restraint
SureLatch Connector
WARNING
12
If the child weighs more than 29.4 kg (65 lbs) or
their shoulders are above the highest harness level,
you MUST use this child restraint as a Booster.
MUST NOT move more than 25 mm (1 inch)
from side-to-side or from front-to-back at the
upper belt path.
*To determine which LATCH connector is on your child
restraint, go to page 15.
13
LATCH is a system for attaching the child restraint to your
vehicle seat. It is to be used in place of your vehicle’s seat
belts and can be used in vehicles with LATCH anchors. Your
vehicle owner’s manual may refer to this system as ISOFIX,
Universal Anchorage System (UAS), or Lower Universal
Anchorage System.
DO NOT install by this
method for a child weighing
more than 22.6 kg (50 lb).
Which Type of Lower Anchor Connector
is on Your Child Restraint?
In order to properly install your child restraint with the
LATCH system, you must first know which type of LATCH
connectors are present on your child restraint.
• If your child restraint has LATCH Hook Connectors,
begin installation by referring to “Installation with LATCH
Hook Connectors,” below.
• If your child restraint has SureLatch Connectors, begin
installation by referring to page 18, “Installation with
SureLatch Connectors.”
• If your child restraint has the Quick Connectors, begin
installation by referring to page 22, “Installation with
Quick Connectors.”
Lower Anchor
Hooks
SureLatch™
Connector
Quick
Connector™
Using with the 5-pt Harness
Installation with Lower Anchor
Connectors
WARNING
• ONLY use for securing child restraint to lower anchor bars.
• ALWAYS read and follow exactly the instructions which
accompany your vehicle and child restraint.
• NEVER attach two hooks to one vehicle lower anchor bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the Lower Anchor Connector
Assembly.
• This Lower Anchor Connector Assembly is intended to be
used ONLY as described in these instructions.
Serious injury or death may result from misuse.
• ALWAYS be sure that the Lower Anchor Connector hook is
fully engaged onto the Vehicle Lower Anchor Bar by pulling
hard on the Lower Anchor Connector strap. If it is not
totally engaged, the Lower Anchor Connector Assembly
will not secure your child restraint. Serious injury or death
may result.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly, with all slack
removed, in storage area on the back of the seat. Roll or
fold excess lower anchor connector strap and secure with a
rubber band to prevent serious injury to vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow your
vehicle owner’s manual.
14
Installation with Lower Anchor Hooks
IMPORTANT:
• Some vehicle manufacturers have lower maximum
weight ratings for LATCH anchors. Consult your vehicle
owner’s manual, or call the vehicle manufacturer, to
confirm the limits on your vehicle’s LATCH anchors.
• If you are using the vehicle seat belt to secure the child
restraint, DO NOT use the Lower Anchor Hooks.
• Install this child restraint with the vehicle seat belt
(NOT Lower Anchor Hooks) if the child weighs more
than 22.6 kg (50 lbs).
1. Disconnect Tether
Hook and Lower
Anchor Hooks
from the back of
the child restraint.
15
Installation with Lower Anchor Hooks
Upper
Belt Path
Tether Strap
4. Secure the child
restraint.
Using your full weight,
push the child restraint
firmly into the vehicle
seat while pulling up
on the LATCH strap to
tighten.
IMPORTANT: To properly protect the child, the child
restraint MUST NOT move more than 25 mm (1 inch) from
side-to-side or from front-to-back at the upper belt path.
If you cannot tightly secure the child restraint, try again or
move it to another location.
2. Place the child restraint in position.
Set child restraint on vehicle seat in forward-facing
position, as shown. Lay the tether strap over the
back of the vehicle seat.
Near Side
Using with the 5-pt Harness
Installation with Lower Anchor Hooks
Far side
5. Connect and tighten tether strap.
Lower Anchor Bar
Lower Anchor Bar
3. Attach Lower Anchor Hooks.
Attach a LATCH Hook Connector onto each seat
anchor.
IMPORTANT: Make sure both LATCH connectors are facing
upward and the harness straps are not twisted.
Connect the tether hook to the anchor behind
the vehicle seat, as shown.
Pull the strap and tighten the tether securely.
IMPORTANT: If your tether strap is too short to reach from
your child restraint to your vehicle tether anchor, you will need
a Tether Extender. Please call ParentLink at 1-800-233-5921
(U.S.) or 1-937-773-3971 (Canada), or 01-800-706-12-00
(Mexico).
Notice
Your child restraint is equipped with one of two types of
tether adjusters: standard (shown above) or the TruTether
(shown below). If your child restraint is equipped with the
TruTether adjuster, refer to page 44 for information about
proper tightening.
TruTether Adjuster
Tightness Indicator
Display
16
17
IMPORTANT:
• Some vehicle manufacturers have lower maximum
weight ratings for LATCH anchors. Consult your vehicle
owner’s manual, or call the vehicle manufacturer, to
confirm the limits on your vehicle’s LATCH anchors.
• If you are using the vehicle seat belt to secure the child
restraint, DO NOT use the SureLatch Connectors.
• Install this child restraint with the vehicle seat belt
(NOT SureLatch connectors) if the child weighs more
than 22.6 kg (50 lbs).
1. Disconnect Tether
Hook from the back
of the child restraint.
Installation with SureLatch Connectors
Near Side
Far Side
Upper
Belt Path
Upper
Belt Path
Lower Anchor Bar
Lower Anchor Bar
3. Attach SureLatch Connectors.
With the SureLatch harness through the upper belt
path, as shown above, push each SureLatch connector
onto each seat anchor.
Note: You may need to vary the angle of the SureLatch
connectors, as shown above, to attach to the anchor.
Using with the 5-pt Harness
Installation with SureLatch Connectors
Strap
Tether Strap
2. Place the child
restraint in position.
Set child restraint on
vehicle seat, as shown.
Lay the Tether Strap over
the back of the vehicle
seat.
18
IMPORTANT: Position the
SureLatch connectors so they
are facing upward, sitting
above the LATCH guide, as
shown, and the straps are
not twisted.
LATCH
Guide
19
Installation with SureLatch Connectors
Installation with SureLatch Connectors
Upper
Belt Path
Using your full weight,
push the child restraint
firmly into the vehicle
seat, as shown, to set it
in place.
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 25 mm (1 inch) from sideto-side or from front-to-back at the upper belt path.
If you can not tightly secure the child restraint, try again,
move it to another location, or install with vehicle seat belt.
LATCH
Guide
Make sure that each SureLatch
connector is above the LATCH
guide, as shown.
5. Connect and tighten
Tether Strap.
Connect the Tether Hook
to the anchor behind
the vehicle seat, as
shown. (Please consult
your vehicle owner’s
manual, as tether anchor
locations may vary.)
Pull the strap and tighten
the Tether securely.
IMPORTANT: If your tether strap is too short to reach from
your child restraint to your vehicle tether anchor, you will need
a Tether Extender. Please call ParentLink at 1-800-233-5921
(U.S.) or 1-937-773-3971 (Canada), or 01-800-706-12-00
(Mexico).
Using with the 5-pt Harness
4. Secure the child
restraint.
Notice
Your child restraint is equipped with one of two types of
tether adjusters: standard (shown above) or the TruTether
(shown below). If your child restraint is equipped with the
TruTether adjuster, refer to page 44 for information about
proper tightening.
TruTether Adjuster
Tightness Indicator
Display
20
21
IMPORTANT:
• Some vehicle manufacturers have lower maximum
weight ratings for LATCH anchors. Consult your vehicle
owner’s manual, or call the vehicle manufacturer, to
confirm the limits on your vehicle’s LATCH anchors.
• If you are using the vehicle seat belt to secure the child
restraint, DO NOT use the Quick Connectors.
• Install this child restraint with the vehicle seat belt
(NOT Quick connectors) if the child weighs more than
22.6 kg (50 lbs).
1. Disconnect Tether
Hook from the back
of the child restraint.
Installation with Quick Connectors
Near Side
Far side
Upper
Belt Path
Upper
Belt Path
Lower Anchor Bar
Lower Anchor Bar
3. Attach Quick Connectors.
With the Quick Connector harness through the upper
belt path, as shown above, push a Quick Connector
onto the Lower Anchor Bar on each side of the child
restraint.
Note: You may need to vary the angle of the Quick
Connectors, as shown above, to attach to the anchor.
IMPORTANT: Make sure both LATCH Quick
Connectors are facing upward, above the LATCH
guide, as shown, and the straps are not twisted.
Correct
Tether
Strap
Using with the 5-pt Harness
Installation with Quick Connectors
Incorrect
2. Place the child
restraint in position.
Set child restraint on
vehicle seat, as shown.
Lay the Tether Strap over
the back of the vehicle
seat.
4. Secure the child
restraint.
Upper
Belt Path
Using your full weight,
push the child restraint
firmly into the vehicle seat
while pulling up on the
Quick Connector Strap to
tighten.
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 25 mm (1 inch) from side-toside or from front-to-back at the upper belt path. If you
can not tightly secure the child restraint, try again, move it
to another location, or install with vehicle seat belt.
22
23
Installation with Quick Connectors
Connect the Tether Hook
to the anchor behind
the vehicle seat, as
shown. (Please consult
your vehicle owner’s
manual, as tether anchor
locations may vary.)
Pull the strap and tighten
the Tether securely.
IMPORTANT: If your tether strap is too short to reach from
your child restraint to your vehicle tether anchor, you will need
a Tether Extender. Please call ParentLink at 1-800-233-5921
(U.S.) or 1-937-773-3971 (Canada), or 01-800-706-12-00
(Mexico).
Notice
Your child restraint is equipped with one of two types of
tether adjuster: standard (shown above) or the TruTether
(shown below). If your child restraint is equipped with the
TruTether adjuster, refer to page 44 for information about
proper tightening.
IMPORTANT:
• Before installing this child restraint with the vehicle
seat belt, you MUST make sure the Lower Anchor Hooks,
SureLatch or Quick Connectors are attached to the
storage D-rings on the seat pad.
• When using the vehicle seat belt to secure the child
restraint, DO NOT use the Lower Anchors. Using both
together can cause slack in a sudden stop of crash.
• Check your vehicle owner’s manual to determine how to
lock your seat belt for child restraint installation. The seat
belt must be locked to properly secure the child restraint.
1. Disconnect Tether
Hook from the
back of the child
restraint.
Using with the 5-pt Harness
5. Connect and tighten
Tether Strap.
Installation with Vehicle Seat Belt
2. Place the child
restraint in
position.
Tether
Strap
Set child restraint on
vehicle seat, as shown.
Lay the Tether Strap over
the back of the vehicle
seat.
3. Route seat belt
through upper
belt path.
TruTether Adjuster
Tightness Indicator
Display
Route the seat belt buckle
tongue through the upper
belt path, as shown.
Upper
Belt Path
4. Buckle seat belt.
24
25
Installation with Vehicle Seat Belt
7. Ensure child
restraint is secure.
5. Remove all slack
from the seat belt.
Using your full weight,
push the child restraint
firmly into the vehicle
seat while tightening
the seat belt to remove
excess slack.
Locking Clip
installed properly
6. Install Locking Clip
(not included), if
necessary.
If your vehicle was built
prior to model year
1996, and has a lap/shoulder belt that is equipped
with an emergency locking
13 mm
retractor (ELR) AND sliding
(0.5 inch)
latch plate, you MUST use
a Locking Clip. Check your
vehicle owner’s manual to
identify which vehicle belt
system is in your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Consult your vehicle owner’s manual before
installing a locking clip.
If your vehicle requires a Locking Clip, please call
ParentLink at 1-800-233-5921 (U.S.) or 1-937-773-3971
(Canada), or 01-800-706-12-00 (Mexico) to obtain a
Locking Clip and instructions on how to install and use
it. to obtain a Locking Clip and instructions on how to
install and use it.
WARNING
• Remove Locking Clip from vehicle seat belt when not
used with a child restraint, or the vehicle seat belt will not
properly restrain an adult or child. Serious injury could
occur.
• DO NOT use a Locking Clip in booster mode.
26
Hold the child restraint
near the upper belt path,
as shown, and try to
move it in all directions.
Upper Belt
Path
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 25 mm (1 inch) from side-toside or from front-to-back at the upper belt path. If you
can not tightly secure the child restraint, try again or move
it to another location.
Using with the 5-pt Harness
Installation with Vehicle Seat Belt
8. Connect and tighten
Tether Strap.
Connect the Tether Hook
to the anchor behind
the vehicle seat, as
shown. (Please consult
your vehicle owner’s
manual, as tether anchor
locations may vary.)
Pull the strap and tighten
the Tether securely.
IMPORTANT: If your tether strap is too short to reach from
your child restraint to your vehicle tether anchor, you will need
a Tether Extender. Please call ParentLink at 1-800-233-5921
(U.S.) or 1-937-773-3971 (Canada), or 01-800-706-12-00
(Mexico).
Notice
Your child restraint is equipped with one of two types of
tether adjusters: standard (shown above) or the TruTether
(shown below). If your child restraint is equipped with the
TruTether adjuster, refer to page 44 for information about
proper tightening.
TruTether Adjuster
Tightness Indicator
Display
27
Securing the Child
Securing the Child
Press the harness release
button on the front of
the seat while pulling
the harness straps.
Snap the two halves of
the chest clip together,
as shown, and slide to
armpit level.
2. Position harness
straps.
Unfasten chest clip and
place the child in the
child restraint.
Bring each harness strap
over the child’s shoulders.
Using with the 5-pt Harness
4. Fasten and adjust
chest clip.
1. Loosen harness.
IMPORTANT: The child’s back and bottom should be flat
against the restraint. If there is a gap, the child will not be
comfortable.
3. Buckle the harness.
Insert both buckle
tongues into the buckle.
Note: Pull up on the
harness straps to ensure
that the buckle tongues
are fastened securely.
28
5. Tighten harness.
Pull the harness adjuster strap to tighten the harness.
Note: Check the harness straps near the shoulders for
slack. You should NOT be able to pinch the harness
(see illustration). Adjust as needed.
IMPORTANT: A snug strap should not allow any slack.
It lies in a relatively straight line without sagging. It does
not press on the child’s flesh or push the child’s body into
an unnatural position.
29
Positioning the Harness Strap
1. Loosen harness
straps.
Press the harness release
button on the front of the
seat while pulling the
harness strap outward
behind the fastened
chest clip.
1. Loosen harness
straps.
Press the harness release
button on the front of
the seat while pulling the
harness straps.
2. Disconnect chest clip.
Push the release button
and pull the chest clip
apart.
Using with the 5-pt Harness
Removing the Child
2. Remove both
harness straps from
the splitter plate.
3. Unbuckle harness.
Press the red button on
the buckle and release
both buckle tongues.
You may now remove
the child.
30
31
Positioning the Harness Strap
Positioning the Crotch Strap
IMPORTANT: You MUST place the crotch strap in the front
slot if your child weighs 18 kg (40 lbs) or more.
3. Move harness strap.
Remove both harness straps from the slots and feed
them into the new slot, as shown.
Pull the harness strap to the back of the child
restraint.
Note: Straps must be positioned at the child’s
shoulder level or slightly above.
IMPORTANT: When inserting harness straps through the
slots in the seat pad, make sure you route them correctly
through their corresponding slots in the seat shell.
4. Attach harness
straps to splitter
plate.
Attach the loop at the
end of each harness strap
onto the splitter plate.
1. Remove crotch
strap.
Loosen the harness
straps and move them
out of the way.
Push the anchor up
through the slot to
the top of the seat.
Using with the 5-pt Harness
As your child grows, you will need to change the crotch
strap position so that it is in the slot closest to your child.
The crotch strap should ALWAYS be as close as possible
to, but NEVER under, the child’s bottom.
2. Insert crotch strap
into new slot.
Insert the crotch strap
anchor into the slot
that is the closest to
the child AND the
most comfortable for
the child.
Pull the crotch strap to
make sure it is secure.
IMPORTANT: Make sure
both harness straps are
installed completely on the
splitter plate, as shown.
32
33
Booster seats raise the child up and help to position the
vehicle lap and shoulder belt correctly. When the child is
properly restrained in a booster seat, their risk of injury
in all types of crashes is reduced, as the lap and shoulder
belt provides excellent restraint of both the upper and lower
torso.
It is important for the child to sit properly within the
vehicle seat belts. When the vehicle seat belt is buckled,
the lap belt should be low on the hips, just touching the
thighs, and the shoulder belt should lie across the middle of
the shoulder. If the child leans out or moves the belt behind
the back or places it under the arm, it will not provide the
intended restraint.
There are a number of things to consider when deciding
whether the child is ready to sit in a booster seat,
including: the weight and height rating on their current
child seat, the child’s own weight and height, their
maturity, and the seating positions available in your vehicle.
How is a booster seat used?
Using a booster seat is very similar to buckling yourself into
the vehicle:
• Read the instruction manuals for both the booster
seat and the vehicle before you start.
• Put the booster in the back seat in a location with
a lap and shoulder belt. Never use a booster
with only a lap belt, as this could cause serious
injuries.
• After the child is in the booster, pull the lap and shoulder
belt across him/her and buckle it.
• Check that the shoulder belt lies across the middle of the
shoulder and that the lap belt is low on the hips, just
touching the thighs.
34
How can you tell if your child is ready to transition
to a booster seat?
You should consider using a booster seat if the following
conditions apply:
• The child is mature enough to sit in the booster seat and
not put the belts under their arm or behind their back.
• The child is approaching the weight or height limit of the
child restraint they are currently using.
• If you have a vehicle that does not have a tether anchorage but has lap/shoulder belts available in the back seat,
a booster seat may provide better protection than an
internal harness seat without the tether.
The shoulder belt MUST
pass through shoulder belt
guide and under the headrest.
The shoulder belt
MUST cross midway
between child’s
shoulder and neck.
The lap belt is
stretched low and
snug across the
child’s hips and
routed under the
lap belt guides.
This line MUST be level
to the ground (Canadian
Models Only).
Using as a Booster Seat
When to Put Your Child
in a Booster Seat
35
Using as a Booster Seat
Child Requirements
Booster Installation Checklist
1. Convert child restraint to booster seat.
Weight: 18 – 49.8 kg (40 – 110 lbs)
Height: 110 – 145 cm (43.3 – 57 in.)
tall AND the tops of the child’s ears are
at, or below, the child restraint headrest.
Age: At least four years old
See “Converting into a Booster Seat,” p. 38.
2. Secure booster seat to the vehicle seat.
aMake sure the bottom and back of the booster seat
The shoulder belt MUST
pass through shoulder
belt guide and under the
headrest.
The shoulder belt
MUST cross midway
between child’s
shoulder and neck.
The lap belt is
stretched low and
snug across the
child’s hips and
routed under the
lap belt guides.
are touching vehicle seat and back.
aLevel the booster seat (Canadian models only),
p. 42.
3. Place the child in the booster seat.
Make sure the child’s back and bottom are flat against
the back and bottom surfaces of the booster seat.
4. Adjust headrest for proper shoulder
belt fit.
The top of the child’s ears are at, or below, the child
restraint headrest and the shoulder belt MUST cross
midway between the child’s shoulder and neck,
as shown at left.
5. Secure child and booster seat to vehicle
seat.
✔Stretch the lap/shoulder belt across the child and
fasten the buckle. Make certain the shoulder belt is
threaded through the shoulder belt guide on the
headrest.
✔Confirm belt routing p. 42.
This line MUST be level
to the ground (Canadian
Models Only).
IMPORTANT
Always secure the booster seat with the LATCH
connectors or vehicle seat belt when not occupied.
An unsecured booster seat can fly into and
injure other occupants in the event of a crash.
36
WARNING
• The shoulder belt MUST NOT cross the child’s neck
or fall off the child’s shoulder. If you can not adjust
the shoulder belt to properly lay midway between
the child’s shoulder and neck AND at or above the
shoulder, try another seating location, or do not use
the booster seat.
Using as a Booster Seat
6. Check your work.
37
Converting into a Booster Seat
1. Loosen harness.
Press the harness release
button while pulling
outward on the harness
straps, as shown.
Disconnect the chest clip.
Converting into a Booster Seat
4. Route the harness
straps through
adjustment slots,
then attach to
splitter plate.
IMPORTANT: Make sure
both harness straps are
installed completely on the
splitter plate.
3. Disconnect all
J-clips and all
retaining strips,
then remove the
seat pad.
38
5. Tuck the chest clip
and buckle tongues
into the recesses on
either side of the
seat shell.
Using as a Booster Seat
2. Remove both
harness straps from
the splitter plate
and pull them
through to the
front of the seat.
39
Converting into a Booster Seat
Converting into a Booster Seat
6. Remove the crotch
strap.
Locate the crotch strap
anchor on the bottom.
Turn the anchor sideways
and push it through the
seat shell to remove, as
shown.
7. Install the seat pad.
Your child restraint is now in Booster Mode and ready
for a child who weighs 18 – 49.8 kg (40 – 110 lbs), is
110 – 145 cm (43.3 – 57 in.) tall, is at least four years
old, and whose ears are below the top of the child
restraint headrest.
Pull the anchor through
the seat and adjust so it
lies flat, as shown.
40
Note: to convert the seat back into 5-point harness
mode, reverse these steps.
Using as a Booster Seat
Insert the crotch strap
anchor back into the
opening from the
bottom of the child
restraint.
41
General Information
Using the SureLatch Connectors
To remove the SureLatch
Connector from a LATCH
anchor or a storage D-ring,
press the red Release Button.
Leveling the Booster Seat
Canadian Models Only
Release Button
Level Line
Towel/Small Blanket
If the level line is not
parallel to the ground,
before fastening child to
the vehicle seat, place
a tightly rolled towel/
small blanket beneath
the bottom rear of the
booster seat, as shown.
Booster Seat Belt Routing
Canadian models:
Only the lap belt must pass under the
guide & fasten into the buckle.
US models:
When used with a child that weighs
18 - 29.4 kg (40 - 65 lbs) both
the lap belt and the shoulder
belt must pass under the guide
& fasten into the buckle.
Using the Quick Connectors
Release Strap
To remove the Quick Connector from a LATCH anchor or
a storage D-ring, pull the red Release Strap.
Using the Latch Hook Connectors
Tab
To remove the Latch Hook
Connector from a LATCH
anchor or a storage D-ring,
press the tab and twist,
then remove the hook.
When used with a child that
weighs 29.4 - 49.6 kg
(65 - 110 lbs) only the lap belt
must pass under the guide & fasten into the buckle.
42
43
Using the TruTether Adjuster
Not available on all models.
Tether straps equipped with the TruTether adjuster attach
to vehicle tether anchor brackets exactly the same as Tether
Straps with standard tether adjusters. TruTether adjusters, however, are equipped with a Tightness Indicator that
shows, at a glance, whether the Tether Strap is properly
tightened. When the Tightness Indicator Display is “green,”
the Tether Strap is tight enough.
TruTether Adjuster
Adjusting the Headrest
To adjust, press the lock
release button, as shown,
while sliding the headrest
up or down to the desired
position.
IMPORTANT: When the
headrest is in one of the four
locking positions, the locking
button will pop into its original position.
Lock Release Button
Removing Seat Pad
Tightness Indicator
Display
J-clips
Connect the Tether Hook to the anchor behind the vehicle
seat, as shown. Pull the strap until you see green in the
tightness indicator display. Once it has turned green, you
have removed all slack and the Tether Strap is adequately
tightened. Be sure to check it periodically to make sure the
indicator is still green. If no green is showing, pull the strap
until it is.
Retaining Strips
(on some models)
1. Disconnect the harness straps from the splitter plate.
2. Disconnect all J-clips and all retaining strips.
Remove the seat pad.
Removing Headrest Pad
J-clips
Disconnect all J-clips
and remove the
headrest pad.
44
45
Securing Your Child Restraint in Aircraft
The Federal Aviation Administration (FAA) recommends
that you secure your child for air travel in an appropriate child restraint based on your child’s weight and size.
Turbulence can happen with little or no warning. When
turbulence occurs, the safest place for your child is
in a properly installed child restraint, not in an
adult’s lap or on the aircraft seat with its seat
belt. Keeping your child in a child restraint during the
flight will help ensure your family arrives safely at your
destination.
The FAA recommends that a child weighing:
• more than 18 kg (40 lbs) use an aircraft seat belt;
• less than 9 kg (20 lbs) use a rear-facing child restraint;
and
• from 9 to 18 kg (20 to 40 lbs) use a forward-facing
child restraint.
Please note that these FAA recommendations
may vary from those applicable to the use of
your child restraint in a motor vehicle.
Installing Child Restraint in Aircraft
Belt Path
Opening
Aircraft
Seat Belt
2. Route aircraft seat belt through belt path.
Route the aircraft seat belt through the belt path
opening in the back of the child restraint and
continue through the opening on the opposite side
of the child restraint.
Note: Lift the restraint’s seat pad away for easier access.
IMPORTANT
You must use the internal harness when installing the
child restraint in aircraft.
Installing Child Restraint in Aircraft
IMPORTANT: Before installing the child restraint, make
sure the aircraft seat is in a fully upright position.
3. Fasten the aircraft seat belt, then remove
all slack from the belt.
Aircraft
Seat Belt
1. Place the child restraint in position.
Place the child restraint on the aircraft seat
forward-facing, as shown above.
46
The aircraft seat belt must be as tight as possible. Route
the excess aircraft seat belt strap back through the belt
path opening. Using your full weight, push the child
restraint firmly onto the aircraft seat while pulling on the
excess seat belt strap to tighten.
Note: Because of the fixed length of aircraft seat belts, the
belt buckle could be behind the child’s back after tightening
the belt. For your child’s comfort, Evenflo recommends
cushioning the child’s back by placing a small pillow or
folded-up blanket, or a folded-up jacket, over the belt buckle.
Check your work: Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in all
directions. If you can move the restraint more than 25 mm
(1 inch) from side-to-side or front to back at the belt
path, the aircraft seat belt is not tight enough, and you
MUST install again until the seat belt is tight.
47
Replacement Parts
Proper Disposal of This Child Restraint
Not available on all models.
You can order replacement parts on-line at www.evenflo.com
or contact Evenflo. When you contact us, please have the product
model number and date of manufacture (found on the back of
the child restraint).
Locking Clip:
(Not included with
child restraint),
see page 26.
Cup Holder/Armrest
Headrest
Pad
At the end of this child restraint’s useful life, Evenflo
encourages you to dispose of it properly. Most of the
components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding,
you may dispose of it in the landfill.
Note: Evenflo uses recycled materials in the
manufacturing process whenever possible but never
for components that are critical for safety.
To prevent injury due to hidden damage, lost
instructions, outdated technology, etc., discontinue use of
this restraint after the expiration date on the label or if it
has been involved in a crash.
Chest Clip
Tether Extender
(Not included with
child restraint)
Manufactured in Fabriqué en
(year-month-day) (anné-mois-jour)
Name / Nom
Model / Modéle
Made in / Fabriqué en
Expires on/Expire le
Seat Pad
Harness System
Head Foam
LATCH Harness with
Hook Connectors
Or
After thoroughly reading and
following these instructions,
store them in the slots on either
side of the child restraint.
Or
LATCH Harness with
SureLatch Connectors
48
LATCH Harness with
Quick Connectors
49
Limited Warranty
For a period of 90 days from the original purchase of
this Product, Evenflo warrants to the original end user
(“Purchaser”) this Product (including any accessories)
against defects in material or workmanship. Evenflo’s
sole obligation under this express limited warranty shall
be, at Evenflo’s option, to repair or replace any Product
that is determined to be defective by Evenflo and
determined to be covered by this warranty.
Repair or replacement as provided under this warranty
is the exclusive remedy of the Purchaser. Proof of
purchase in the form of a receipted invoice or bill of
sale evidencing that the Product is within the warranty
period must be presented to obtain warranty service.
This express limited warranty is extended by Evenflo
ONLY to the original Purchaser of the Product and is not
assignable or transferable to subsequent purchasers or
end users of the Product. For warranty service, contact
Evenflo’s ParentLink Consumer Resource Center at
www.evenflo.com.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON
THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO
SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES
OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED
WARRANTY ON THIS PRODUCT, OR ANY WARRANTY
IMPLIED BY OPERATION OF LAW. OTHER THAN THE
EXPRESS LIMITED WARRANTY SET FORTH ABOVE, THERE
ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS
PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER
EXPRESS REPRESENTATION OF ANY KIND IS HEREBY
DISCLAIMED.
50
• www.evenflo.com
• USA: 1-800-233-5921, 8 AM to 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
INSTRUCTIONS
Store these instructions in
the slots on either side of
the child restraint.
www.evenflo.com
USA: 1-800-233-5921, 8 AM to 5 PM E.T.
Canada: 1-937-773-3971
México: 01-800-706-12-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising