GE Intelligent Platforms
GE
Intelligent Platforms
CT12
High Performance Dual Core 6U CPCI Single Board Computer
Features
• IPMI 2.0 PICMG 2.9
• Intel Core™ i7 and Core™ i5 processors
- Dual core, up to 2.53 GHz
- Integrated memory interface, 1066 MHz
• Watchdog, temperature sensors
• Single slot 6U CPCI form factor
• Optional -40° C to +75° C operating
temperature range
®
• PICMG® compliant
• Up to 8 Gbyte DDR3 SDRAM (dual
channel) with ECC in main memory
(soldered components)
• OS support: standard distribution Linux®
and Windows®
For telecom applications, the CT12 is
equipped with IPMI 2.0 functionality.
• Optional conformal coating
• Customization on request
• Up to 16 Gbyte NAND Flash (soldered)
• BIOS backup Flash
• User EEPROM
• Optional onboard SATA HDD
• Optional one or two PMC or XMC sites
• Front I/O:
- Two Gigabit Ethernet ports
- VGA
- One USB
- One COM 3
• Rear I/O:
- Two Gigabit Ethernet ports
- VGA 1
- DVI 1 and 2
- Three SATA interfaces
- COM 1 and 2 ports
- Four USB ports
- GPIOs
- PMC/XMC I/O signals
The BIOS Flash is optionally backed with a
second Flash device in order to recover the
BIOS in the event the primary BIOS is corrupted. The Flash device is large enough to
optionally host additional pre-boot applications, for example Built-In Test (BIT).
The CT12 is a single slot 6U CompactPCI
SBC with an Intel® Core™ i7 plus QM57
peripheral controller hub. The assembly is
fully compliant to the PICMG® specifications.
®
The CT12 is able to host one Dual Core processor with a core clock of up to 2.53 GHz.
The assembly is ready to accept higher
performance processor variants when introduced by Intel.
Four banks of DDR3 SDRAM components
are provided on the CT12 for a maximum
of 8 GBytes of main memory with ECC. The
module also hosts up to 16 GByte soldered
NAND Flash through an IDE interface and
may be provisioned with higher Flash
capacities when required for specific applications. The onboard NAND Flash is an
ideal storage media to keep application
specific data.
Supported operating systems for the CT12
include Linux® and Microsoft® Windows® as
well as VxWorks®.
The CT12 is also available in an extended
operating temperature version (-40° C to
+75° C). The upper limit of the temperature
range depends on the selected processor
version and the optional population with
PMC, XMC mezzanines or a SATA hard drive.
The CT12 is designed for use in a broad
range of applications such as telecom/
communications, industrial control and
automation, test, and measurement systems, as well as server blade applications.
This, combined with a customer specific
assembly service, provides optimized price
and performance levels.
Please contact GE Intelligent Platforms for
a current list of processors and OS versions
supported on the CT12.
CT12 High Performance Dual Core 6U CPCI Single Board Computer
CT12 Safety and Reliability Benefits
Soldered processor and memory
Increased immunity against shock and
vibration
Soldered NAND Flash drive
Higher immunity against shock and
vibration compared to CompactFlash
BIOS Backup Flash
Fast recovery when BIOS upgrade got
corrupted
Optional Built-In Test routines for platform
integrity tests
HW Write Protect
Protects onboard code and data against
unauthorized write access
Specifications
Processor - μFCBGA, Low Power Design
• Scalable embedded processing power
• 32 nm process
• Intel Core i7 processor, up to 2.53 GHz
• Cache up to 4 MB, full speed
• Dual core version
• Low power processor versions
• Intel Hyper-Threading technology (two threads
per core)
• Intel Turbo Boost support
• Two PCI Express x8 ports
• FDI and DMI interface to I/O Controller hub
• Contact GE Intelligent Platforms for current
processor versions
Processor Speed
GHz
MB i7-610E
L2
Memory
MHz
2.53
4
1066
i7-620LE
2.00
4
1066
i7-620UE
1.06
4
800
CompactPCI
• PICMG 2.0 R3.0 compliant CPCI local bus standard
• 64-bit PCI for up to 8 slots (33 MHz) or 5 slots (66 MHz)
• Supports both system Host and Peripheral Mode in
a single assembly
• 2 mm pin and socket connectors (IEC-1076-4-101)
I/O Controller Hub
• FDI and DMI interface to processor
• Supplies I/O interfaces/functions to front and rear
• 8 PCI Express ports
• Choice of four display channels
Main Memory Array
• Dual channel DDR3 SDRAM array: 4 banks soldered
memory components
• 144-bit wide with error correction (ECC)
• Configurable capacity: 1 GByte to 8 GBytes
Flash ROM Memory
• Up to 16 GBytes NAND Flash
• Accessed by processor through IDE
• Soldered down for high reliability
• Wear leveling
Front Dual Gigabit Ethernet
• Twin Intel 82574L PCI Express Ethernet controllers
• 10/100/1000BaseT auto-negotiation
• Ordering option
LED
• Front panel ACPI system Status indicator LED (red/
amber/green)
• CompactPCI Hot swap (blue) on front panel
Rear Dual Gigabit Ethernet
• Twin Intel 82574L PCI Express Ethernet controllers
• 10/100/1000BaseT auto-negotiation
• Compliant to PICMG 2.16
Hot-Swap - compliant to PICMG 2.1
• Peripheral mode: full CompactPCI Hot Swap
• System Host mode: CompactPCI ENUM# event
support through ACPI or legacy driver
Onboard Hard Disk or SSD Drive
• Optional internal 2.5” SATA hard disk or 2.5” SATA Solid
State Drive (SSD)
• Usage of SSD is recommended for high shock and
vibration immunity as well as extended temperature
applications
Front and Rear I/O (Transition Module CTM20)
Function
PMC/XMC Extension Slots
• Optional as PMC or XMC extension slots
• Optional one or two extension slots
• Extension slot 1: PMC (64-bit PCI, up to 133 in PCI-X
mode) or XMC with PCI Express x8 (Gen2, 2.5 Gbit/s)
• Extension slot 2: PMC (64-bit PCI, up to 133 in
PCI-X mode) or XMC with PCI Express x8
(Gen2, 2.5 Gbit/s)
• Extension slot 2 is not available in case a 2.5” storage
device is installed
• PCI signaling is 3.3V, 5V tolerant
Serial I/O
• Two async. 16550 compatible full duplex
serial channels
• High-speed transfer up to 115.2 kbaud with
16 byte FIFOs
• User selectable RS-232/422/485 interfaces at rear
• COM3 RS-232 available at front via Har-Link®
connector
Video/Graphics Interface
• Intel integrated 3D graphics controller
• One VGA port at front via Har-Link connector
• One VGA port plus two DVI-D ports at rear I/O
• Any two ports can be used for dual display operation
• Fully compliant support for OpenGL™ for all Windows
operating systems and Linux
General Purpose I/O
• 13 GPIO (input or output) pins
• Software configurable
• Hardware Write Protection of programmable devices
USB Ports
• One USB 2.0 connector on the front
• Four USB 2.0 channels on rear
Keyboard and Mouse
• Via USB
• Legacy PS/2 controller emulation
Real-time Clock
• RTC 146818 compatible
• Li-battery
FrontRear
VGA 1
VGA 2
•
DVI 1 & 2
•
COM 1 •
•
COM 2 •
USB 0-3
•
USB 4
•
Ethernet 1,2
•
Ethernet 3,4 •
SATA 2
•1 SATA 3-5
•
GPIO
•
LEDs •
•
PMC 1 / XMC 1 I/O
•
•
PMC 2 / XMC 2 I/O •
•
•
•
Reset 1
•
If Flash ROM option is not used
BIOS Features
• New AMI Aptio UEFI, in-system programmable
Flash ROM
• CPU, memory and SATA auto-detection/selection
• Integrated Ethernet PXE driver
• USB mass storage support and booting capability
(floppy, HDD, CDROM, and onboard Flash ROM array)
• Password protection
• Headless operation
IPMI 2.0
• Baseboard Management Controller supporting the
Intelligent Platform Management Interface (IPMI)
architecture in compliance with PICMG 2.9
• Peripheral mode and BMC mode are supported
• IPMI is an optional function
Software
• Windows
• Linux
• VxWorks
Styles
Style
AF
Ext. Temperature
no
yes
Conformal coating is a custom option.
EEPROM
• 512 kbit serial EEPROMs for non-volatile user data
Power Requirements
• +5 V, +3.3 V, +12 V
• -12 V if required by mounted PMC module
Timer
• Integrated in Hub controller
• Legacy PC-AT timer
• HPET High Precision Event Timer
Power Allowances – PMC/XMC Slots
• +5 V, +3.3 V: Total power max. 7.5 W
• ±12 V: 100mA each
Watchdog
• Super I/O
Temperature Sensors
• CPU die and chipset die temperature software readable in the range of –15°C to +105°C
Power Consumption - typical operating current
• Without keyboard, hard disk, Windows, 3D graphics
active, Gigabit Ethernet channels not active,
measured at DOS prompt, no power savings. 1 GB
memory option. (See manual.)
CT12 High Performance Dual Core 6U CPCI Single Board Computer
Block Diagram
Specifications (continued)
Temperature
• Note: Consult the User’s Manual or GE Intelligent
Platforms for additional detailed information on the
operating temperature behavior of the module. The
CT12 operating temperature range is influenced by
processor type and speed, operating altitude, and
the type of cooling used in the host system.
• All values under typical conditions without
PMC/XMC module.
RangeOperating
Storage
Standard
0° C to +55° C
–40° C to +85° C
Extended
-40° C to +75° C
–40° C to +85° C
OperatingStorage
Humidity
5 - 95% @ 40° C Altitude
15.000 ft. (4.5 km) 40.000 ft. (12 km)
5 - 95% @ 40° C
Mechanical – PICMG 2.0
• 6U, 1 slot wide, 233 mm x 160 mm x 20 mm with
Flash drive or hard disk
Altitude
• Operating: Sea level to 15,000 ft. (4.5 km)
• Storage: Sea level to 40,000 ft. (12 km)
Shock and Vibration
• Designed to meet VITA47 class EAC1 and EAC3
MTBF
• Prediction calculations are available in accordance
with MIL-HDBK-217. Please contact GE Intelligent
Platforms.
PCIe x4
Dual
Channel
Dual
DDR3 ECC
Channel
DDR3 ECC
Intel Core i7
Core i5
PCI 66 MHz
PCI-X
Bridge
PCIe x8
PCIe x4/x8
PCI-X
Bridge
CPCI Bus
PCI-X
PMC 1
XMC 1
1066 MHz
1x VGA (f )
1x VGA (f )
DVI-I (r)
DVI-I (r)
BIOS
PCI-X
Bridge
PCIe x4
LEDs/Power
PCH
1x USB (f )
4x USB (r)
PCIe x1
PCIe x1
PCIe x1
1x COM (f )
4x COM (r)
PCIe x1
PCI-X
PMC 2 1
XMC 2 1
GbE
GbE (f )
GbE
GbE (f )
GbE
GbE (r)
GbE
GbE (r)
GPIO (r)
Safety
• Designed to meet standard UL1950, CE class A,
FCC-A
SATA (r)
Onboard
Flash
Onboard
SATA 1
IPMI
(f ) = Front
(r) = Rear
1
Optional: PMC/XMC or SATA
Ordering Information
CT12AUF2K10A
6U cPCI PC, single slot, Core i7-610E 2.53 GHz, 4 GB DDR3, 4 GB NAND drive, 2x front GigE,
2x rear GigE, 2x SATA, VGA (front), COM (front), VGA (rear), 2x COM (rear), 2x USB (rear),
4x SATA (rear)
CT12CUF2K10A
6U cPCI PC, single slot, Core i7-620LE 2.0 GHz, 4 GB DDR3, 4 GB NAND drive, 2x front GigE,
2x rear GigE, 2x SATA, VGA (front), COM (front), VGA (rear), 2x COM (rear), 2x USB (rear),
4x SATA (rear)
CTM20A10A
6U I/O transition module for CT12 without onboard SATA drive with all onboard and
face plate I/O ports.
YLB-CR12-01
Front I/O COM port cable (appr. 200 mm), Har-Link connector to serial connector
YLB-CR12-02
Front I/O VGA port cable (appr. 200 mm), Har-Link connector to VGA connector
CR12-SDK-LINUX
System Development Kit for Linux (Fedora 12, RHEL 5.4, Suse 11.2)
BVXW-CRCT12-01M Board Support Package (BSP) for Workbench/VxWorks 6.x with maintenance
TVXW-CRCT12-01M Board Support Package (BSP) and Enhanced Support Package (ESB) for Workbench/
VxWorks 6.x with maintenance
VXW6-ECR12
VxWorks 6.x Board Support Package (BSP) and Extended Board Support Package (ESB)
CR12-SDK-WIN
System Development Kit for Windows XP, (planned Windows7)
Operating Systems For detailed information and further options, contact GE Intelligent Platforms
GE Intelligent Platforms Contact Information
Americas: 1 800 433 2682 or 1 434 978 5100
Global regional phone numbers are listed by location on our web site at www.ge-ip.com/contact
www.ge-ip.com
©2011 GE Intelligent Platforms, Inc. All rights reserved.
All other brands or names are property of their respective holders.
Specifications are subject to change without notice.
07.11 GFA-1334
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement