10/100/1000Base-Tx to 1000Base

10/100/1000Base-Tx to 1000Base
10/100/1000Base-Tx to 1000Base-Fx
Media Converter
Overview
This product supports IEEE802.3 10 Base-T
standard/IEEE 802.3u 100Base-TX/FX standard IEEE
802.3z 1000Base-TX/FX standard, IEEE 802.3x Flow
control standard as well as full duplex and half duplex
mode.
The media converter transforms the transmission
media of Ethernet signal from CAT5 100m to optical
fiber 850/1310/1550nm. It can extend the transmission
distance to several kilometers or hundred kilometers.
All Wintop Media converters apply the new 0.25µm
technology to improve the performance and to avoid the
packet lost with long the transmission. It also reduce the
delay time to less than 9.6 µs
Using media converter is an economical solution to achieve long distance transmission
base on current status.
1. Interface
RJ-45 interface: One port 10/100/1000Base-Tx, the transmission media adopts CAT5
twisted-pair with typical length of 100 meter. It features the function of automatically
identifying the through line and cross wire
Fiber interface: One port 1000Base-Fx, SC/UPC fiber interface is of duplex mode type,
including two interfaces, namely TX and RX. When the two sets of optical transceiver are
interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely
"TX-RX", "RX-TX" (direct butting for single optical fiber).
2. Connection
The network device (work station, hub or switch) with RJ-45 interface is connected to RJ-45
jack of optical transceiver through twisted-pair. And the multi/single mode fiber is connected to
SC/UPC fiber interface of the optical transceiver single and dual fiber. Then switch on. The
corresponding LED is on for correct connection. (See the table below for the LED indicator
lamp).
Table 1 : Front panel for single fiber media converter
Table 2 : Front panel for dual fiber media converter
3. Explanation for LED indicator lamp
LED indicator lamps serve as device monitoring and trouble display. The following is the
explanation for each LED indicator lamp.
1
LED
Function
Status
ON
OFF
ON
OFF
ON
PWR
Power LED
FX
Fiber port signal detect LED
FX-LINK/ACT
Fiber port link/action status
LED
Blink
1000M
UTP port speed LED
OFF
ON
OFF
ON
TX-LINK/ACT
UTP port link/action status
LED
Blink
FDX/COL
UTP port duplex LED
OFF
ON
OFF
Description
Power is ON
Power is Fail
Laser is receiving
No laser input
Fiber link is OK
Data is been received or
transmitted
Fiber link is fail
1000Mbps speed
100Mbps speed
UTP link is OK
Data is been received or
transmitted
UTP link is fail
Full duplex
Half duplex
Main features
1. In conformity to IEEE 802.3 10 Base-T standard.
In conformity to IEEE 802.3u 100 Base-TX/FX standard.
In conformity to IEEE 802.3z 1000 Base-TX/FX standard.
In conformity to IEEE 802.3x Flow control standard.
2. Max. 2M buffer memory built in chip.
Auto negotiation back pressure flow control for full duplex IEEE802.3 X and half duplex.
3. Automatic identification of MDI/MDI-X cross line.
4. High-performance1.4Gbps memory bandwidth.
5. In conformity to safety code of FCC and 15 CLASS B and CE MARK.
Technical parameters
1. Standard Protocol:
IEEE802.3 10 Base-T standard
IEEE 802.3u 100Base-TX/FX standard
IEEE 802.3z 1000Base-TX/FX standard
IEEE 802.3x Flow control standard
2. Connector: 1 UTP RJ-45 connector, 1 SC/ST connector
3. Operation mode: full duplex mode or half duplex mode
4. Power supply parameter: 90-240Vac, 50/60Hz with outside switching adaptor: 5V DC
built-in: 110-265VAC or 48VDC
power consumption: 4W
5. Environmental temperature: 0oC - 60 oC
6. Relative humidity: 5%-90% none-condensing
7. BER < 1E-9
8. TP cable: Cat5 UTP cable 100m
9. Transfer fiber: multi-mode: 50/125, 62.5/125 or 100/140µm
single mode: 8.3/125, 8.7/125, 9/125 or 10/125µm
10.Dimensions:
External power supply: 26mmx 70mm x 95mm
Internal power supply: 30mm x 110mm x 140mm
Cautions
1. This product is suitable for indoor application.
2. Put on the dust cover of fiber interface when not used.
3. It is forbidden to stare at the TX fiber-transfer end with naked eyes.
4. Single optical fiber transceiver must be used in pair (See the attachment description in
delivery).
2
Trouble shooting
1. Device is not matched. Please select the corresponding network device according to the
transfer rate of the product (10Mbps or 100Mbps) when connected to other network devices
(network card, hub, switch).
2. Line loss is excessive during the fiber wiring. Excessive loss in connector plug-in and fiber
soldering welding and excessive intermediate nodes may cause excessive loss rate or abnormal
operation
Ordering information
PN
WT-8110GMA-1105AS
WT-8110GMA-112AS
WT-8110GSA-1110AS
WT-8110GSA-1120AS
WT-8110GSA-1140AS
WT-8110GSA-1160AS
WT-8110GSB-1110A-AS
WT-8110GSB-1110B-AS
WT-8110GSB-1120A-AS
WT-8110GSB-1120B-AS
WT-8110GSB-1140A-AS
WT-8110GSB-1140B-AS
WT-8110GSB-1160A-AS
WT-8110GSB-1160B-AS
ƛ TX
nm
ƛ RX
nm
PTX
dBm
SEN
dBm
Overload
dBm
Distance
Km
Loss
dB/km
850
850
-8~-3
≤-19
≥-3
0.55
2.5
1310
1310
-8~-3
≤-20
≥-3
0.55
0.4
1310
1310
-8~-3
≤-24
≥-3
10
0.4
1310
1310
-8~-3
≤-24
≥-3
20
0.4
1550
1550
-5~0
≤-24
≥-3
40
0.25
1550
1550
-5~0
≤-24
≥-3
60
0.25
1310
1550
-8~-3
≤-24
≥-3
10
0.4
1550
1310
-8~-3
≤-24
≥-3
10
0.25
1310
1550
-8~-3
≤-24
≥-3
20
0.4
1550
1310
-8~-3
≤-24
≥-3
20
0.25
1310
1550
-5~0
≤-24
≥-3
40
0.4
1550
1310
-5~0
≤-24
≥-3
40
0.25
1310
1550
-2~+3
≤-24
≥-3
60
0.4
1550
1310
-5~0
≤-24
≥-3
60
0.25
Connector
MM Dual
SC
MM Dual
SC
SM Dual
SC
SM Dual
SC
SM Dual
SC
SM Dual
SC
SM BIDI
SC
SM BIDI
SC
SM BIDI
SC
SM BIDI
SC
SM BIDI
SC
SM BIDI
SC
SM BIDI
SC
SM BIDI
SC
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement