SBC-860 Rev. A
F u l l - size CPU Card
SBC-860
SBC-860 Rev. A
Socket 478 based Intel®
Pentium® 4 processor
Full-size CPU Card
With Integrated Intel®
82845GV chipset, DDR,
4 USBs, Dual Ethernet
& CompactFlash.
SBC-860 Rev. A Manual 6th Ed.
Jan. 2004
F u l l - size CPU Card
SBC-860
Copyright Notice
This document is copyrighted, 2004. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, or for any infringements upon the rights of third parties that may result from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have been
made in the preparation of this document to assure its accuracy,
AAEON assumes no liabilities resulting from errors or omissions in this
document, or from the use of the information contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i
F u l l - size CPU Card
SBC-860
Acknowledgments
All other products’name or trademarks are properties of their respective
owners.
l
Award is a trademark of Award Software International, Inc.
l
CompactFlash™ is a trademark of the Compact Flash Association.
l
Intel® , Pentium® 4, and Celeron® are trademarks of Intel®
Corporation.
l
Microsoft Windows® is a registered trademark of Microsoft Corp.
l
ITE is a trademark of Integrated Technology Express, Inc.
l
IBM, PC/AT, PS/2, and VGA are trademarks of International Business
Machines Corporation.
l
SoundBlaster is a trademark of Creative Labs, Inc.
ii
F u l l - size CPU Card
SBC-860
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
•
1
SBC-860 Full-Size CPU Card
•
1
Quick Installation Guide
•
1
CD-ROM for manual (in PDF format), and drivers
•
1 HDD Cable
•
1 FDD Cable
•
1 Audio and COM Port Cable with bracket
•
1 LPT and COM Port Cable with bracket
•
1
•
1 USB Cable with bracket
Y-Cable (Keyboard and Mouse)
If any of these items should be missing or damaged, please contact your
distributor or sales representative immediately.
iii
F u l l - size CPU Card
SBC-860
Contents
Chapter 1 General Information
1.1 Introduction .................................................................................... 1-2
1.2 Features............................................................................................ 1-4
1.3 Specifications................................................................................... 1-5
Chapter 2 Quick Installation Guide
2.1 Safety Precautions .......................................................................... 2-2
2.2 Location of Connectors and Jumpers......................................... 2-3
2.3 Mechanical Drawing ...................................................................... 2-5
2.4 List of Jumpers................................................................................ 2-7
2.5List of Connectors........................................................................... 2-8
2.6 Setting Jumpers............................................................................... 2-10
2.7 Front Panel (JP1)............................................................................ 2-11
2.8 COM2 RS-232/422/485 Selection - 1 (JP2) ............................. 2-11
2.9 COM2 RI / +5V / +12V Selection (JP3) ................................. 2-11
2.10 COM2 RS-232/422/485 Selection – 2 (JP4) .......................... 2-12
2.11 CPU FSB Setting (JP5)................................................................ 2-12
2.12 Clear CMOS (JP6)........................................................................ 2-12
2.13 Watchdog Timer (JP7)................................................................. 2-12
2.14 ATX Power Connector (CN1) .................................................. 2-13
2.15 System Fan Connector (CN2).................................................... 2-13
2.16 Floppy Drive Connector (CN3) ................................................ 2-14
2.17 Parallel Port 1 Connector (CN4)............................................... 2-16
iv
F u l l - size CPU Card
SBC-860
2.18 ATX PWM 4P Power Connector (CN5)................................. 2-16
2.19 Primary IDE Hard Drive Connector (CN6)........................... 2-17
2.20 Serial Port COM 2 (CN7)........................................................... 2-18
2.21 Serial Port COM 1 (CN8)........................................................... 2-19
2.22 Secondary IDE Hard Drive Connector (CN9)....................... 2-19
2.23 Wake on LAN Connector (CN10)............................................ 2-20
2.24 IrDA Connector (CN11) ............................................................ 2-20
2.25 USB 2.0 Port 2 Connector (CN12)........................................... 2-21
2.26 USB 2.0 Port 1 Connector (CN13)........................................... 2-21
2.27 CRT Display Connector (CN14)............................................... 2-22
2.28 Ethernet 10/100/1000BaseT RJ-45 Phone Jack (CN15) ..... 2-23
2.29 Ethernet 10/100 BaseT RJ-45 Phone Jack (CN17)............... 2-23
2.30 Audio Input/Output Connector (CN18) ................................ 2-24
2.31 Mini-DIN PS/2 Connector (CN19)......................................... 2-25
2.32 CPU Fan Connector (CN20) ..................................................... 2-25
2.33 Internal Keyboard Connector (CN21)..................................... 2-25
2.34 Internal Mouse Connector (CN22)........................................... 2-26
2.35 Compact Flash Disk Connector (CN23) ................................. 2-26
2.36 External 5V SB/PWRGD Connector (CN24)....................... 2-27
Chapter 3
Award BIOS Setup
3.1 System Test and Initialization. ..................................................... 3-2
3.2 Award BIOS Setup......................................................................... 3-4
3.2.1 Main Setup .........................................................................................3-7
3.2.2 Advanced Features Setup...............................................................3-11
3.2.3 Default Setup....................................................................................3-36
v
F u l l - size CPU Card
SBC-860
3.2.4 Security Setup...................................................................................3-37
3.2.5 PC Health Setup...............................................................................3-38
3.2.6 Clk/Voltage Setup...........................................................................3-40
3.2.7 Exit Setup..........................................................................................3-42
Chapter 4 Driver Installation
4.1 Installation 1.................................................................................... 4-3
4.2 Installation 2.................................................................................... 4-4
4.3 Installation 3.................................................................................... 4-5
Appendix A Programming the WatchDog Timer
A.1 How to program the watchdog timer ....................................A-2
vi
F u l l - s ize CPU Card
SBC-860
1
Chapter
General
Information
Chapter 1 General Information
1- 1
F u l l - s ize CPU Card
SBC-860
1.1 Introduction
Introducing AAEON’s new SBC-860, powered by Intel Pentium® 4
processor, full size form factor single board computer (SBC) with an
onboard CompactFlash Type II and four USB 2.0!
SBC-860 successfully deployed Intel most advanced 82845GV chipset,
which supports high CPU frequency up to 3.06 GHz with front side bus
running at 400MHz /533MHz. SBC-860 supports Intel
Hyper-Threading Technology gives you the best overall Pentium 4
processor performance available. SBC-860 also provides high memory
capacity up to 2 GB DDR DRAM (DDR 200/266).
In addition to its powerful computing engine, the full functional design
of the board includes features such as chipset integrated 2D/3D graphics
engine with AGP 4x bandwidth, built-in USB2.0 and on board
CompactFlash Type II socket. SBC-860 delivers super graphic
performance without additional cost on integrated Intel 82845GV
chipset, and provides unique IntelExtreme Graphics architecture to
maximize VGA performance capability.
Four USB 2.0 ports provide an expandable, Plug and Play serial interface
that ensures a standard low-cost connection for peripheral devices.
Industrial applications will benefit from the four USB2.0 by two
Chapter 1 General Information
1-2
F u l l - s ize CPU Card
SBC-860
pin-headers, offering 480Mbps high-speed efficiency and value without
compromising performance.
Moreover, SBC-860 is also equipped with Dual Intel Ethernet
controllers. One of these provides superior 1Giga Mbps networking
access ability for high speed networking applications such as gateway,
VPN, Mini server.
In short, this product is a versatile P4 level compact board with the best
cost-performance for CTI, networking, and mini-server markets.
Chapter 1 General Information
1-3
F u l l - s ize CPU Card
SBC-860
1.2 Features
n
Supports Intel® Pentium® 4 mSocket 478 CPU
n
Integrated AC-97 2.3 codec PCI 3D Audio
n
Supports type II CompactFlash
n
4 USB ports onboard
n
High Drive design to enhance the ISA driving capacity
n
Supports H/W status monitoring
n
Support 1 IrDA
n
Onboard 2 IDE connectors (Support 4 devices)
n
Supports Ultra DMA 100
n
Dual Ethernet (1 Intel® 82562 phy, 1 82551QM/ER or 82540EM)
for option
Chapter 1 General Information
1-4
F u l l - s ize CPU Card
SBC-860
1.3 Specifications
System
l
CPU
Supports Intel® 478 pin Pentium® 4 (400/533
MHz FSB).
l
Chipset
Intel® 82845GV
Intel® 82801DB (ICH4)
l
IO Chipset
ITE-8712. Fully 16-bit I/O decoded
l
BIOS
Award 4 Mb Flash BIOS.
l
System Memory
Onboard Two184-pin DDR DRAM slot, supports
up to 2.0Gbyte DDR 200/266
l
Enhanced IDE
Interface
Supports Four IDE devices. Supports Ultra
DMA/100 mode with data transfer rate up to
100MB/sec. Connector: Two (20x2) 2.54mm
pin header with box
l
FDD Interface
Supports up to two floppy disk drives, 5.25"
(360KB and 1.2MB) and /or 3.5" (720KB, 1.44MB
and 2.88MB) Connector: One (17x2) 2.54 mm pin
l
USB Ports
header with box
4 USB 2.0 ports
Connector: Two (5x2) 2.00mm pin header
l
Serial Ports
Two RS-232 serial ports, can be configured as
COM1, COM2, or disabled individually and one
RS-232/422/485(COM2). COM2 provide the
option to select 12V/5V/RING function by
Chapter 1 General Information
1-5
F u l l - s ize CPU Card
SBC-860
jumper setting. (16C550 equivalent)
Connector:
Two (5x2) 2.00mm pin header
l
Parallel port
One bi-directional parallel port. Supports SPP,
ECP, and EPP modes. Connector: One (13x2)
2.00mm pin header
l
Keyboard/ PS2
Mouse connector
A 6-pin mini-DIN connector supports PC/AT
KBD and PS/2 mouse, Addition 5-pin (wafer) and
4-pin (wafer) supports PC/AT KBD and mouse
for IPC applications. Supports WakeOn KBD and
Mouse
l
Watchdog Timer
Generate a system reset. Software selectable
time-out interval
l
SSD
CompactFlash slot onboard support type 2 CFD.
l
IRDA Port
Support SIR and CIR
Connector: One 6 pin 2.54mm header
l
DMA
7 DMA channels (8237 equivalent)
l
Interrupt
15 interrupt levels (8259 equivalent)
l
Power
Management
Supports ATX power supply. ACPI 2.0 compliant.
l
H/W status
monitoring
Embedded in ITE8712 supports power supply
voltages and temperature monitoring.
Audio Interface
l
Chipset
ALC655
l
Codec
AC-97 2.3 SoundBlaster compatible PCI 3D
Chapter 1 General Information
1-6
F u l l - s ize CPU Card
SBC-860
Audio
l
Interface
One (7x2) 2.0mm pin header for Microphone In,
Line In/Out, CD-In
Display
l
Chipset
Intel® 82845GV
l
Display Memory
Share up to 8MB with Dynamic Video Memory
Technology
l
Display Type
Supports non-interlaced CRT
l
Resolution
Up to 1600 x 1200 @ 16.7M colors
Ethernet Interface
l
Chipset
Dual 10/100 Ethernet (1 Intel® 82562 Phy and
one Intel® 82551QM/ER) or one Intel® 82540EM
10/100/1000 Gigabit Ethernet (1 Intel® 82562
Phy and 1 Kenai-32)
l
Interface
Two RJ45 connector 1x10/100 and 1xGbE. LAN
LED support. Support WOL and optional support
for AOL
Chapter 1 General Information
1-7
F u l l - s ize CPU Card
SBC-860
Expansion Interface
l
PCIMG
l
ISA Bus
ITE IT8888 PCI to ISA bridge
l
High Drive
Support 64mA high driving capability for ISA-bus
slot on backplane
Mechanical and Environment
l
Dimension
13.3”(L) x 4.8”(W)
l
Weight
1.2lb (0.5kg)
l
Operating
Temperature
0~60℃ (32~140℉)
l
Power Supply
Voltage
Chapter 1 General Information
+5V, +12V, +3.3V, +5VSB.
ATX/ATX12V Power Supply version 1.2
1-8
F u l l - size CPU Card
SBC-860
2
Chapter
Quick
Installation
Guide
Notice:
The Quick Installation Guide is derived from Chapter 2 of
user manual. For other chapters and further installation
instructions, please refer to the user manual CD-ROM that
came with the product.
Part No. 2007860015
Chapter 2 Quick Installation Guide
Printed in Taiwan Jan. 2004
F u l l - size CPU Card
SBC-860
2.1 Safety Precautions
Always completely disconnect the power cord from
your board whenever you are working on it. Do not
make connections while the power is on, because a
sudden rush of power can damage sensitive
electronic components.
Always ground yourself to remove any static charge
before touching the board. Modern electronic
devices are very sensitive to static electric charges.
Use a grounding wrist strap at all times. Place all
electronic components on a static-dissipative surface
or in a static-shielded bag when they are not in the
chassis
Chapter 2 Quick Installation Guide
2-2
F u l l - size CPU Card
SBC-860
2.2 Location of Connectors and Jumpers
Locating connectors and jumpers (component side)
Chapter 2 Quick Installation Guide
2-3
F u l l - size CPU Card
SBC-860
Locating connector (solder side)
Chapter 2 Quick Installation Guide
2-4
F u l l - size CPU Card
SBC-860
2.3 Mechanical Drawing
Mechanical drawing (component side)
Chapter 2 Quick Installation Guide
2-5
F u l l - size CPU Card
SBC-860
Mechanical Drawing (solder side)
Chapter 2 Quick Installation Guide
2-6
F u l l - size CPU Card
SBC-860
2.4 List of Jumpers
The board has a number of jumpers that allow you to configure your system to
suit your application.
The table below shows the function of each of the jumpers of the board:
Jumpers
Label
Function
JP1
Front Panel
JP2
COM2 RS232/422/485 Mode Selection – 1
JP3
COM2 RI / +5V / +12V Selection
JP4
COM2 RS232/422/485 Mode Selection – 2
JP5
CPU FSB Setting
JP6
Clear CMOS
JP7
Watchdog Timer
Chapter 2 Quick Installation Guide
2-7
F u l l - size CPU Card
SBC-860
2.5 List of Connectors
The board has a number of connectors that allow you to configure your system to
suit your application.
The table below shows the function of each of the connectors of the board:
Connectors
Label
Function
CN1
ATX Power Connector
CN2
System Fan Connector
CN3
Floppy Drive Connector
CN4
Parallel Port 1 Connector
CN5
ATX_PWM 4P Power Connector
CN6
Primary IDE Hard Drive Connector
CN7
Serial Port COM2 Connector
CN8
Serial Port COM1 Connector
CN9
Secondary IDE Hard Drive Connector
CN10
Wake on LAN Connector
CN11
IrDA Connector
CN12
USB 2.0 Port 2 Connector
CN13
USB 2.0 Port 1 Connector
CN14
CRT Display Connector
CN15
Ethernet 10/100/1000 BaseT RJ-45 Phone Jack
CN17
Ethernet 10/100 BaseT RJ-45 Phone Jack
CN18
Audio Input/Output Connector
CN19
Mini-Din PS/2 Connector
CN20
CPU Fan Connector
CN21
Internal Keyboard Connector
CN22
Internal Mouse Connector
Chapter 2 Quick Installation Guide
2-8
F u l l - size CPU Card
SBC-860
CN23
Compact Flash Disk Connector
CN24
External 5VSB/PWRGD Connector
Chapter 2 Quick Installation Guide
2-9
F u l l - size CPU Card
SBC-860
2.6 Setting Jumpers
You configure your card to match the needs of your application by setting jumpers.
A jumper is the simplest kind of electric switch. It consists of two metal pins and a
small metal clip (often protected by a plastic cover) that slides over the pins to
connect them. To “close” a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2 and 3. In this case you would connect either pins 1 and 2 or 2 and 3.
3
1 2
Open
Closed
Closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubt about the best hardware configuration for your application,
contact your local distributor or sales representative before you make any change.
Generally, you simply need a standard cable to make most connections.
Chapter 2 Quick Installation Guide
2 - 10
F u l l - size CPU Card
SBC-860
2.7 Front Panel (JP1)
Pin
Signal
Pin
Signal
1
GND
2
Power Button
3
HDD LED
4
VCC
5
External Speaker
6
VCC
7
Power LED
8
GND
9
Reset Button
10
GND
2.8 COM2 RS-232/422/485 Selection – 1 (JP2)
JP2
Function
1-2, 4-5, 7-8, 10-11
2-3, 5-6, 8-9, 11-12
RS-232 (Default)
RS-422
2-3, 8-9
RS-485
2.9 COM2 RI / +5V / +12V Selection (JP3)
JP3
Function
5-6
3-4
RI (Default)
+5Volt.
1-2
+12Volt.
Chapter 2 Quick Installation Guide
2 - 11
F u l l - size CPU Card
SBC-860
2.10 COM2 RS-232/422/485 Selection - 2 (JP4)
JP4
Function
1-2
3-4
RS-232 (Default)
RS-422
5-6
RS-485
2.11 CPU FSB Setting (JP5)
JP5
Function
1-2
CPU Auto Detect (Default)
2-3
400MHz
Open
533MHz
2.12 Clear CMOS (JP6)
JP11
Function
1-2
2-3
Normal (Default)
Clear CMOS
2.13 Watchdog Timer (JP7)
JP7
Function
1-2
Open
Select Hardware Reset for WDT (Default)
Select Keyboard Reset for WDT
Chapter 2 Quick Installation Guide
2 - 12
F u l l - size CPU Card
SBC-860
2.14 ATX Power Connector (CN1)
Pin
Signal
Pin
Signal
1
3.3 Volt.
11
3.3 Volt.
2
3.3 Volt.
12
-12 Volt.
3
GND
13
GND
4
5 Volt.
14
PS_ON
5
GND
15
GND
6
5 Volt.
16
GND
7
GND
17
GND
8
ATXPWRGD
18
-5 Volt.
9
5 Volt. Stand By
19
5 Volt.
10
12 Volt.
20
5 Volt.
2.15 System Fan Connector (CN2)
Pin
Signal
1
GND
2
+12 Volt.
3
FAN Sense
Chapter 2 Quick Installation Guide
2 - 13
F u l l - size CPU Card
SBC-860
2.16 Floppy Drive Connector (CN3)
With two options on floppy drive you could simply adopt any of the combinations
of 5.25" (360 KB and 1.2 MB) and/or 3.5" (720 KB, 1.44 MB, and 2.88 MB)
drives onto the mainboard.
A 34-pin daisy-chain drive connector cable is required for a dual-drive system. On
one end of the cable is a 34-pin flat-cable connector. On the other end are two
sets of floppy disk drive connectors. Each set consists of a 34-pin flat-cable
connector (usually used for 3.5" drives) and a printed-circuit board connector
(usually used for 5.25" drives).
Wire number 1 on the cable is normally red or blue, and the other wires are usually
gray.
Connecting the floppy drive
1. Plug the 34-pin flat-cable connector into CN3. Make sure that the red or blue
wire corresponds to pin 1 on the connector.
2. Attach the appropriate connector on the other end of the cable to the floppy
drive(s). You can use only one connector in the set. The set on the end
(after the twist in the cable) connects to the A: drive. The set in the middle
connects to the B: drive.
3. If you are connecting a 5.25" floppy drive, line up the slot in the printed circuit
board with the blocked-off part of the cable connector.
If you are connecting a 3.5" floppy drive, you may have trouble
determining which pin is pin number 1. Look for a number printed on the circuit
Chapter 2 Quick Installation Guide
2 - 14
F u l l - size CPU Card
SBC-860
board indicating pin number 1. Also, the connector on the floppy drive connector
may have a slot. When the slot is up, pin number 1 should be on the right. Check
the documentation that came with the drive for more information.
Floppy (CN3)
Pin
Signal
Pin
Signal
1
3
GND
GND
2
4
DENSEL#
N.C
5
GND
6
N.C
7
GND
8
INDEX#
9
GND
10
MTRA#
11
GND
12
DRVB#
13
GND
14
DRVA#
15
GND
16
MTRB#
17
GND
18
DIR#
19
GND
20
STEP#
21
GND
22
WDATA#
23
GND
24
WGATE#
25
GND
26
TRK0#
27
GND
28
WPT#
29
N.C
30
RDATA#
31
GND
32
HDSEL#
33
N.C
34
DSKCHG#
Chapter 2 Quick Installation Guide
2 - 15
F u l l - size CPU Card
SBC-860
2.17 Parallel Port 1 Connector (CN4)
Pin
Signal
Pin
Signal
1
3
STBX
PTD0
2
4
AFD#
ERR#
5
PTD1
6
PINIT#
7
PTD2
8
SLIN#
9
PTD3
10
GND
11
PTD4
12
GND
13
PTD5
14
GND
15
PTD6
16
GND
17
PTD7
18
GND
19
ACK#
20
GND
21
BUSY
22
GND
23
PE
24
GND
25
SLCT
26
N.C
2.18 ATX PWM 4P Power Connector (CN5)
Pin
Signal
1
GND
2
GND
3
+12 Volt.
4
+12 Volt.
Chapter 2 Quick Installation Guide
2 - 16
F u l l - size CPU Card
SBC-860
2.19 Primary IDE Hard Drive Connector (CN6)
Pin
Signal
Pin
Signal
1
3
PRI_IDERST#
PDD7
2
4
GND
PDD8
5
PDD6
6
PDD9
7
PDD5
8
PDD10
9
PDD4
10
PDD11
11
PDD3
12
PDD12
13
PDD2
14
PDD13
15
PDD1
16
PDD14
17
PDD0
18
PDD15
19
GND
20
N.C
21
PDREQ
22
GND
23
PDIOW#
24
GND
25
PDIOR#
26
GND
27
PIORDY
28
GND
29
PDDACK#
30
GND
31
IRQ14
32
N.C
33
PDA1
34
P66DET
35
PDA0
36
PDA2
37
PDCS#1
38
PDCS#3
39
IDEACTP#
40
GND
Chapter 2 Quick Installation Guide
2 - 17
F u l l - size CPU Card
SBC-860
2.20 Serial Port COM2 (CN7)
COM 2 supports RS-232/422/485 mode, which allows you to connect
serial devices (mouse, printer, etc.)
COM 2/RS-232 Mode (CN7)
Pin
Signal
Pin
Signal
1
3
DCDB
TXB
2
4
RXB
DTRB
5
GND
6
DSRB
7
RTSB
8
CTSB
9
RIB
10
N.C
COM 2/RS-422 Mode (CN7)
Pin
Signal
Pin
Signal
1
TXD-
2
RXD+
3
TXD+
4
RXD-
5
N.C
6
N.C
7
N.C
8
N.C
9
GND
10
N.C
COM 2/RS-485 Mode (CN7)
Pin
Signal
Pin
Signal
1
3
TXDTXD+
2
4
N.C
N.C
5
N.C
6
N.C
7
N.C
8
N.C
9
GND
10
N.C
Chapter 2 Quick Installation Guide
2 - 18
F u l l - size CPU Card
SBC-860
2.21 Serial Port COM1 (CN8)
Pin
Signal
Pin
Signal
1
3
DCDA
TXA
2
4
RXA
DTRA
5
GND
6
DSRA
7
RTSA
8
CTSA
9
RIA
10
N.C
2.22 Secondary IDE Hard Drive Connector(CN9)
Pin
Signal
Pin
Signal
1
3
SEC_IDERST#
SDD7
2
4
GND
SDD8
5
SDD6
6
SDD9
7
SDD5
8
SDD10
9
SDD4
10
SDD11
11
SDD3
12
SDD12
13
SDD2
14
SDD13
15
SDD1
16
SDD14
17
SDD0
18
SDD15
19
GND
20
N.C
21
SDREQ
22
GND
23
SDIOW#
24
GND
25
SDIOR#
26
GND
27
SIORDY
28
GND
29
SDDACK#
30
GND
31
IRQ15
32
N.C
33
SDA1
34
S66DET
35
SDA0
36
SDA2
37
SDCS#1
38
SDCS#3
39
IDEACTS#
40
GND
Chapter 2 Quick Installation Guide
2 - 19
F u l l - size CPU Card
SBC-860
2.23 Wake on LAN Connector (CN10)
Pin
Signal
1
2
5VSB
GND
3
RI/PCI_PME#
4
SMBDATA
5
SMBCLK
2.24 IrDA Connector (CN11)
Pin
Signal
1
2
Vcc
CIR_Tx
3
GND
4
IR_RX
5
IR_TX
6
CIR_RX
Chapter 2 Quick Installation Guide
Pin
Signal
2 - 20
F u l l - size CPU Card
SBC-860
2.25 USB 2.0 Port 2 Connector (CN12)
SBC-860 provides four USB (Universal Serial Bus) interfaces, which give
complete plug and play, hot attach/detach for up to 127 external devices.
The USB interfaces comply with USB specification Rev. 2.0, and can be
disabled in the system BIOS setup.
Pin
Signal
Pin
Signal
1
3
USBVDD2-3
USBD2-
2
4
USBGND
USBGND
5
USBD2+
6
USBD3+
7
USBGND
8
USBD3-
9
USBGND
10
USBVDD2-3
2.26 USB 2.0 Port 1 Connector (CN13)
Pin
Signal
Pin
Signal
1
3
USBVDD0-1
USBD0-
2
4
USBGND
USBGND
5
USBD0+
6
USBD1+
7
USBGND
8
USBD1-
9
USBGND
10
USBVDD0-1
Chapter 2 Quick Installation Guide
2 - 21
F u l l - size CPU Card
SBC-860
2.27 CRT Display Connector (CN14)
Pin
Signal
Pin
Signal
1
2
CRT_RED
DRT_GREEN
9
10
5 Volt.
VGA GND
3
DRT_BLUE
11
N.C
4
N.C
12
CRT_SDA
5
VGA GND
13
CRT_HSYNC
6
VGA GND
14
CRT_VSYNC
7
VGA GND
15
CRT_VSYNC
8
VGA GND
Chapter 2 Quick Installation Guide
2 - 22
F u l l - size CPU Card
SBC-860
2.28 Ethernet 10/100/1000 BaseT RJ-45 Phone Jack (CN15)
SBC-860 supports dual 10/100 Ethernet (1 Intel 82562 Phy and 1 Lavon)
or One 10/100 and one Giga bit Ethernet (1 Intel 82562 Phy and 1
Kenai-32). The high-speed Ethernet connectors provide complete plug and
play 10Mb/s, 100 Mb/s and 1000Activity LED of the Giga bit Ethernet
are as follows:
Orange: Gigabit
Green: 100M
10/100Base-Tx RJ-45 Connector
No light: 10M
10/100/1000Base-Tx RJ-45 Connector
2.29 Ethernet 10/100 BaseT RJ-45 Phone Jack (CN17)
CN17 is the RJ-45 connector based on the chipset
integrated LAN. The figure at the left side shows
the pin out assignments of the connector and its
corresponding input jack.
Chapter 2 Quick Installation Guide
2 - 23
F u l l - size CPU Card
SBC-860
2.30 Audio Input/Output Connector (CN18)
2 Channel Audio Output Mode (Default)
Pin
Signal
Pin
Signal
1
3
MIC_in
GND
2
4
MIC_Vcc
CD_GND
5
LINE_in Left
6
CD_in Left
7
LINE_in Right
8
CD_GND
9
GND
10
CD_in Right
11
LINE_out Left
12
LINE_our Right
13
GND
14
GND
5 Channel Audio Output Mode
Pin
Signal
Pin
Signal
1
3
Center Out
GND
2
4
MIC_Vcc
CD_GND
5
Rear Left Out
6
CD_in L
7
Rear Right Out
8
CD_GND
9
GND
10
CD_in R
11
Front Left Out
12
Front Right Out
13
GND
14
GND
Note: If you would like to transfer the mode from 2 Channel to 5 Channel,
you will set up through the driver. The further transferring
procedure will be shown in the Chapter 4 Driver Installation. When
you set it as 5 Channel mode, Mic_in and Line_in will be disable.
Chapter 2 Quick Installation Guide
2 - 24
F u l l - size CPU Card
SBC-860
2.31 Mini-DIN PS/2 Connector (CN19)
Pin
Signal
Pin
Signal
1
3
Mouse Clock
Vcc
2
4
Keyboard Clock
GND
5
Keyboard Data
6
Mouse Data
2.32 CPU Fan Connector (CN20)
Pin
Signal
1
2
GND
+12 Volt.
3
FAN Sense
2.33 Internal Keyboard Connector (CN21)
Pin
Signal
1
2
Keyboard clock
Keyboard data
3
N.C
4
GND
5
Vcc
Chapter 2 Quick Installation Guide
2 - 25
F u l l - size CPU Card
SBC-860
2.34 Internal Mouse Connector (CN22)
Pin
Signal
1
2
Mouse clock
Mouse data
3
GND
4
Vcc
2.35 Compact Flash Disk Connector (CN23)
Pin
Signal
Pin
Signal
1
2
GND
SDD3
26
27
GND
SDD11
3
SDD4
28
SDD12
4
SDD5
29
SDD13
5
SDD6
30
SDD14
6
SDD7
31
SDD15
7
SDCS#1
32
SDCS#3
8
GND
33
GND
9
GND
34
SDIOR#
10
GND
35
SDIOW#
11
GND
36
Vcc
12
GND
37
IRQ15
13
Vcc
38
Vcc
14
GND
39
CSEL
15
GND
40
N.C
16
GND
41
SEC_IDERST#
17
GND
42
SIORDY
18
SDA2
43
N.C
19
SDA1
44
Vcc
Chapter 2 Quick Installation Guide
2 - 26
F u l l - size CPU Card
SBC-860
20
SDA0
45
DASP#
21
SDD0
46
PDIAG#
22
SDD1
47
SDD8
23
SDD2
48
SDD9
24
N.C
49
SDD10
25
GND
50
GND
2.36 External 5V SB/PWRGD Connector (CN24)
Pin
Signal
1
N.C
2
GND
3
PWRGD
4
GND
5
PS_ON
6
5VSB
Chapter 2 Quick Installation Guide
Pin
Signal
2 - 27
Full size CPU Card
SBC-860
3
Chapter
Award
BIOS Setup
Chapter 3 Award BIOS Setup
3-1
Full size CPU Card
SBC-860
3.1 System test and initialization
These routines test and initialize board hardware. If the routines encounter
an error during the tests, you will either hear a few short beeps or see an
error message on the screen. There are two kinds of errors: fatal and
non-fatal. The system can usually continue the boot up sequence with
non-fatal errors. Non-fatal error messages usually appear on the screen
along with the following instructions:
Press <F1> to RESUME
Write down the message and press the F1 key to continue the boot up
sequence.
When you should encounter fatal errors, please contact your distributor or
sales representative.
System configuration verification
These routines check the current system configuration the values stored in
the CMOS memory of the board. If they do not match, the program
outputs an error message. You will then need to run the BIOS setup
program to set the configuration information in memory.
There are three situations in which you will need to change the CMOS
settings:
You are starting your system for the first time
You have changed the hardware attached to your system
The CMOS memory has lost power and the configuration information has
Chapter3 Award BIOS Setup
3-2
Full size CPU Card
SBC-860
been erased.
The SBC-860 CMOS memory has an integral lithium battery backup for
data retention. However, you will need to replace the complete unit when
it finally runs down.
Chapter3 Award BIOS Setup
3-3
Full size CPU Card
SBC-860
3.2 Award BIOS CMOS setup
Awards BIOS ROM has a built-in Setup program that allows users to
modify the basic system configuration. This type of information is stored
in battery-backed CMOS memory so that it retains the Setup information
when the power is turned off.
Some items in the BIOS are programmed to auto detect your system. The
presence or the values of these items vary with the corresponding
hardware specification of your system.
A.
Entering setup
Power on the computer and press <Del> immediately.
This will allow you to enter Setup. The top menu offers
users various functions to configure the system. The
default page after entering the BIOS setup is [Main –
Standard CMOS setup].
B.
Major Setup Features
Main – Standard CMOS Features
Use this menu for basic system configuration. (Date,
time, IDE, etc.)
C.
Advanced Features Setup
Use this menu to set the advanced features available on
your system.
Chapter3 Award BIOS Setup
3-4
Full size CPU Card
l
SBC-860
Advanced BIOS Features
Use this menu to set the advanced features available
on your system.
l
Advanced Chipset Features
Use this menu to change the values of the chipset
registers and optimize your system performance.
l
Integrated Peripherals
Use this menu to specify your settings for integrated
peripherals. (USB, Serial port, Parallel port, keyboard,
mouse etc.)
l
Power Management Setup
Use this menu to specify your settings for power
management. (HDD power down, power on by events,
KB wake up, etc.)
l
PnP/PCI Configurations
This entry appears if your system supports PnP/PCI.
D.
Default – Load Optimized Defaults
Use this menu to load the BIOS default values that are
factory settings for optimal performance system
operations. While AWARD has designated the custom
BIOS to maximize performance, the factory has the
right to change these defaults to meet their needs.
Security – Set/Change Password
Chapter3 Award BIOS Setup
3-5
Full size CPU Card
SBC-860
Use this menu to set Supervisor/User Passwords.
E.
Clk/Voltage Setup
Use this menu to specify your settings for auto detect
DIMM/PCI clock and spread spectrum.
F.
PC Health Setup
This menu allows you to set the shutdown temperature
for your system.
Exit Setup
G.
Save and Exit Setup
Save CMOS value changes to CMOS and exit setup.
H.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
Chapter3 Award BIOS Setup
3-6
Full size CPU Card
3.2.1
l
SBC-860
Main Setup
Standard CMOS setup
Select [Main] for STANDARD CMOS SETUP option from the
top menu, the screen shown below is displayed. This standard
Setup Menu allows users to configure system components such
as date, time, hard disk drive, floppy drive and display. Once a
field is highlighted, on-line help information is displayed in the
right box of the Menu screen.
Date and Time Configuration
The BIOS determines the day of the week from the other date
information. This field is for information only.
Press the left or right arrow key to move to the desired field
(date, month, year). Press the PgUp/- or PgDn/+ key to
change the setting, or type the desired value into the field.
Chapter3 Award BIOS Setup
3-7
Full size CPU Card
SBC-860
The time format is based on the 24-hour military-time clock.
For example, 1 p.m. is 13:00:00 hours. Press the left or right
arrow key to move to the desired field. Press the PgUp/- or
PgDn/+ key to change the setting, or type the desired value
into the field.
ü
IDE Primary/Secondary Master/Slave
IDE HDD Auto-Detection
This section does not show information about other
IDE devices, such as a CD-ROM drive, or other hard
drive types, such as SCSI drives.
NOTE: We recommend that you select type AUTO for
all drives.
The BIOS can automatically detect the specifications
and optimal operating mode of almost all IDE hard
drives. When you select AUTO for a hard drive, the
BIOS will detect its specifications
ü
IDE Primary/Secondary Master/Slave
If you do not want to select "AUTO", other methods of
selecting the drive type are available:
1.NONE: No drive type to be selected.
2.Manual: This will allow you to manually set the drive
type you
Chapter3 Award BIOS Setup
are using in your system. (See as below)
3-8
Full size CPU Card
SBC-860
Drive A
Drive B
Select the correct specifications for the diskette drive(s)
installed in the computer.
ü
n
None
No diskette drive installed
n
360K, 5.25 in
5- 1 / 4 i n c h P C -t y p e s t a n d a r d
drive; 360 kilobyte capacity
n
1.2M, 5.25 in
5- 1 / 4 i n c h A T-t y p e
high-density drive; 1.2 megabyte c a p a c i t y
n
720K, 3.5 in
3- 1 / 2 i n c h d o u b l e - sided drive;
72 0 k i l o b y t e c a p a c i t y
n
1.44M, 3.5 in
3- 1 / 2 i n c h d o u b l e - sided drive;
1.44 mega byte capacity
n
2.88M, 3.5 in
3- 1 / 2 i n c h d o u b l e - sided drive;
2.88 mega byte capacity
Video
This function setting allows you to select the video type.
The choices: EGA/VGA, CGA 40, CGA 80, MONO
ü
Halt On
During the power-on-self-test (POST), the computer
will stop if the BIOS detects a hardware error. You can
tell BIOS to ignore certain errors during POST and
continue the boot-up process.
The choices: All, But Keyboard; All, But Diskette;
All, But Disk/Key; All Errors; No Errors.
Chapter3 Award BIOS Setup
3-9
Full size CPU Card
ü
SBC-860
Base Memory
Typically 640 KB. Also called conventional memory.
The DOS operating system and conventional
applications use this area.
ü
Extended Memory
Above the 1-MB boundary. Early IBM personal
computers could not use memory above 1 MB, but
current PCs and their software can use extended
memory.
ü
Total Memory
The fields show the total installed random access
memory (RAM).
Chapter3 Award BIOS Setup
3 - 10
Full size CPU Card
SBC-860
3.2.2 Advanced Features Setup
l
Advanced BIOS Features
By choosing the [Advanced BIOS Feature] option from the
initial setup menu, the screen below is displayed.
Chapter3 Award BIOS Setup
3 - 11
Full size CPU Card
SBC-860
Virus Warning
When enabling this item, you receive a warning message if a
program (specifically, a virus) attempts to write to the boot
sector or the partition table of the hard disk drive. You
should then run an anti-virus program. Keep in mind that
this feature protects only the boot sector, not the entire hard
drive.
NOTE: Many disk diagnostic programs that access the boot sector table
can trigger the virus-warning message. If you plan to run such a program, we
recommend that you first disable the virus warning. Before installing
Microsoft Windows, please disable this function.
The choices: Enabled, Disabled.
ü
Hyper Threading Technology
If your Pentium 4 processor supports this function, you
can select Enabled for Windows XP and Linux 2.4x OS
optimized for Hyper Threading Technology. Select
Disabled for other OS which does not optimize for
Hyper Threading Technology. If your processor can’t
support this function, this item will be hidden.
The choices: Enabled, Disabled
ü
Quick Power On Self Test
Select Enabled to reduce the amount of time required to
run the power-on-self-test (POST) while system booting.
Chapter3 Award BIOS Setup
3 - 12
Full size CPU Card
SBC-860
The choices: Enabled, Disabled.
ü
First/Second/Third Boot Device
The BIOS attempts to load the operating system from
the devices in the sequence selected in these items.
The choices: Floppy, LS120, HDD, SCSI, CDROM,
ZIP100, USB-FDD, USB-ZIP, USB-CDROM,
USB-HDD, LAN, ISA-FDD , Disabled.
ü
Boot Other Device
If your boot device, such as SCSI/RAID, is not included
in the following choices “Floppy, LS120, HDD, SCSI,
CDROM, ZIP100, USB-FDD, USB-ZIP,
USB-CDROM, USB-HDD, LAN, ISA-FDD”, you may
set First/Second/Third Boot devices to "Disabled" and
enable the BOOT Other Device function. The system
will automatically boot the other device.
The choices: Enabled, Disabled.
ü
Swap Floppy Drive
This field is effective only in systems with two floppy
drives. Selecting enabled assigns physical drive B to
logical drive A, and vice-versa.
The choices: Enabled, Disabled.
ü
Boot Up Floppy Seek
Chapter3 Award BIOS Setup
3 - 13
Full size CPU Card
SBC-860
When Enabled, the BIOS tests (seeks) floppy drives to
determine whether they have 40 or 80 tracks. Only
360-KB floppy drives have 40 tracks; drives with 720
KB, 1.2 MB, and 1.44 MB capacity all have 80 tracks.
Because very few modern PCs have 40-track floppy
drives, we recommend you to choose "Disabled" to save
time.
The choices: Enabled, Disabled.
ü
Boot Up NumLock Status
Toggle between On or Off to control the state of the
NumLock key when the system boots. When toggled
On, the numeric keypad generates numbers instead of
controlling cursor operations.
The choices: On, Off.
ü
Gate A20 Option
Gate A20 refers to the way the system addresses
memory above 1 MB (extended memory). When set to
Fast, the system chipset controls Gate A20. When set to
Normal, a pin in the keyboard controller controls Gate
A20. Setting Gate A20 to fast improves system speed,
particularly with OS/2 and Windows.
The choices: Fast, Normal.
ü
Typematic Rate Setting
Chapter3 Award BIOS Setup
3 - 14
Full size CPU Card
SBC-860
Keystrokes repeat at a rate determined by the keyboard
controller. When enabled, the typematic rate and
typematic delay can be selected.
The choices: Enabled/Disabled.
ü
Typematic Rate
When the typematic rate setting is enabled, you can
select a typematic rate, at which character repeats when
you hold down a key.
The choices: 6, 8, 10, 12, 15, 20, 24, 30.
ü
Typematic Delay
When the typematic rate setting is enabled, you can
select a typematic delay, at which before keystrokes
begin to repeat.
The choices: 250, 500, 750, 1000 (milliseconds).
ü
Security Option
If you have set a password, select whether the password
is required every time the System boots, or only when
you enter Setup.
The choices: Setup, System.
ü
APIC Mode
Advanced programmable interrupt controller, it can be
used for either uni-processor or multi-processor.
Chapter3 Award BIOS Setup
3 - 15
Full size CPU Card
SBC-860
The choices: Enabled, Disabled
ü
Silent Post
This feature allows you to enable the system to show
AAEON’s logo when power is on.
The choices: Enabled, Disabled
Chapter3 Award BIOS Setup
3 - 16
Full size CPU Card
l
SBC-860
Advanced Chipset features setup
By choosing the [Advanced Chipset Features Setup] option from
the INITIAL SETUP SCREEN menu, the screen below is
displayed.
ü
DRAM Timing Selectable
This function stores information about Memory Module
setting. Therefore, it can auto detect the best frequency
that the memory module should use.
The Choices: By SPD, Manual.
ü
CAS Latency Time
When synchronous DRAM is installed, the number of
clock cycles of CAS latency depends on the DRAM
timing. Do not reset this field from the default value
Chapter3 Award BIOS Setup
3 - 17
Full size CPU Card
SBC-860
specified by the system designer. The values of the
choice may very with different RAM types.
The choices: 1.5, 2, 2.5, 3
ü
Active to Precharge Delay
This function identifies the minimum active to
precharge time
The choices: 5, 6, 7
ü
DRAM RAS# to CAS# Delay
This function controls the number of clocks that are
inserted between a row activate command and a read or
write command to that row.
The choices: 2, 3
ü
DRAM RAS# Precharge
This function controls the number of clocks that are
inserted between a row precharge command and an
active command to the same row.
The choices: 2, 3
ü
Memory Frequency For
This item allows you to select the memory frequency.
The choices: Auto, DDR200, DDR266.
Chapter3 Award BIOS Setup
3 - 18
Full size CPU Card
ü
SBC-860
System BIOS Cacheable
Selecting Enabled allows caching of the system BIOS
ROM at F0000h-FFFFFh, resulting in better system
performance.
The choices: Enabled, Disabled.
ü
Video BIOS Cacheable
Selecting Enabled allows caching of the video BIOS
ROM at C0000-C8000, resulting in better video
performance.
The choices: Enabled, Disabled.
ü
Memory Hole At 15M-16M
Enable this function to allow ISA ROM to map to
15-16M and support Legacy ISA devices. If you don’t
utilize legacy ISA devices in your system, you are
recommended to disable this function to enhance
graphic performance.
The choices: Enabled, Disabled.
ü
AGP Aperture Size (MB)
Aperture size will ensure that all writes posted in the
global write buffer to the graphics aperture are retired to
DRAM before initiating any CPU-PCI cycle. This can be
used to ensure synchronization between the CPU and
AGP master.
Chapter3 Award BIOS Setup
3 - 19
Full size CPU Card
SBC-860
The choices: 4, 8, 16, 32, 64, 128, 256.
ü
On Chip VGA Setting
* On-Chip VGA
This allows users to select to Enable or Disable the
onboard VGA function.
The choices: Enabled, Disabled
* On-Chip Frame Buffer Size
This function is used to select the amount of main
memory that is pre-allocated to support the internal
graphics device.
The choices: 1MB, 8MB
Chapter3 Award BIOS Setup
3 - 20
Full size CPU Card
l
SBC-860
Integrated Peripherals
By choosing the [Integrated Peripherals] option from the
INITIAL SETUP SCREEN menu, the screen below is
displayed.
ü
IDE DMA transfer access
This function to enable/disable IDE DMA transfer in
DOS mode.
The choices: Enabled, Disabled
ü
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE
interface with support for two IDE channels. Select
Enabled to activate each channel separately.
The choices: Disabled, Enabled.
ü
IDE Primary or Secondary Master/Slave PIO
Chapter3 Award BIOS Setup
3 - 21
Full size CPU Card
SBC-860
The four IDE PIO (Programmable Input/Output)
fields let you set a PIO mode (0-1) for each of the two
IDE devices and the two storage devices that the
onboard IDE interface supports. Modes 0 through 4
provide successively increased performance. In Auto
mode, the system automatically chooses the best mode
for each device.
The choices: Auto, Mode 0, Mode 1, Mode 2, Mode
3, Mode 4.
ü
IDE Primary or Secondary Master/Slave UDMA
Ultra DMA100 implementation is possible only if your
IDE hard drive supports it and the operating
environment includes a DMA driver. If both your hard
drive and IDE cable support Ultra DMA 100 select
Auto to enable BIOS support.
The choices: Auto, Disabled.
ü
USB/ USB 2.0 Controller
USB controller: This function is used to enable/disable
onboard USB controller
USB 2.0 controller: This function is used to
enable/disable high speed USB 2.0 device
The choices: Disabled, Enabled.
ü
USB Keyboard/Mouse Support
Chapter3 Award BIOS Setup
3 - 22
Full size CPU Card
SBC-860
Select Enabled when you use a Universal Serial Bus
(USB) keyboard/Mouse under DOS mode.
The choices: Disabled, Enabled.
ü
Onboard Audio/LAN 1/LAN 2
The default setting for this item is "Enabled". If you
don't utilize onboard LAN / Audio funciton, just
configure it as "Disabled" without any efforts on jumper
setting.
The choices: Disabled, Enabled.
ü
Init Display First
You can select Onboard/AGP or PCI slot to initialize it
as the primary display before initializing any other
display device on the system.
The choices: Onboard/AGP, PCI Slot,
ü
IDE HDD Block Mode
Block mode is also called "block transfer", "multiple
commands", or "multiple sector read/write". If your
IDE hard drive supports block mode (most new drives
do), please select "Enabled" for automatic detection of
the optimal number of block read/writes per sector the
drive can support.
The choices: Disabled, Enabled.
Chapter3 Award BIOS Setup
3 - 23
Full size CPU Card
ü
SBC-860
Power on Function
Despite the power on switch, all the devices listed below
could be defined as power on methods.
The choices: Any key, Button only, Keyboard 98,
Password, Hot key, Mouse move, Mouse click.
ü
KB Power On Password
If you select Password in the above power on function,
you have to press Enter here to set the password so that
you can power on the system by typing the password.
ü
Hot key power on
If you select Hot key as the power on method, you
have to define the Hot key in this section.
The choices: Ctrl-F1, Ctrl-F2, ..., Ctrl-F12.
Onboard FDC Controller
Select Enabled if your system has a floppy disk
controller (FDC) installed on the system board and you
wish to use it. If you install an add-in FDC or the system
has no floppy drive, select Disabled in this field.
The choices: Disabled, Enabled.
ü
Onboard Serial Port 1/2
Normally, the boards' I/O chips will occupy a certain
portion of memory space. For each I/O device the
Chapter3 Award BIOS Setup
3 - 24
Full size CPU Card
SBC-860
computer provides an I/O address. The more devices
attached the more address needed to organize the
memory storage areas. If all the I/O devices were
running through the same address, your devices would
come to a near halt. Also the corresponding interrupt
needs to be selected.
The choices: Disabled, Auto, 2E8/IRQ3,
3E8/IRQ4, 2F8/IRQ3, 3F8/IRQ4.
ü
UART Mode Select
If you don't disable Onboard Serial Port 2, you will have
to select an operating mode for the second serial port:
Normal: RS-232C serial port
IrDA: IrDA-compliant serial infrared port
ASKIR: Amplitude shift keyed infrared port
SCR: Smart Card Reader
The choices: Normal, IrDA, ASKIR, SCR.
ü
UR2 Duplex Mode
Select the value required by the IR device connected to
the IR port. Full-duplex mode permits simultaneous
two-direction transmission. Half-duplex mode permits
transmission in one direction only at a time.
The choices: Half, Full.
Chapter3 Award BIOS Setup
3 - 25
Full size CPU Card
ü
SBC-860
Onboard Parallel Port
Select a logical LPT port address and corresponding
interrupt for the physical parallel port.
The choices: Disabled, 378/IRQ7, 278/IRQ5,
3BC/IRQ7.
ü
Parallel Port Mode
Two bi-directional parallel ports. Supports ECP, EPP,
ECP+EPP, SPP.
The choices: SPP, EPP, ECP, ECP+EPP.
ü
ECP Mode Use DMA
Select a DMA channel for the port.
The choices: 1, 3.
Chapter3 Award BIOS Setup
3 - 26
Full size CPU Card
l
SBC-860
Power Management Setup
By choosing the [Power Management Setup] option from the
INITIAL SETUP SCREEN menu, the screen below is displayed.
This sample screen contains the SBC-860’s default values for the
SBC-860.
ü
ACPI Function
This item allows you to enable/disable the Advanced
Configuration and Power Interface (ACPI).
The choices: Enable, Disable
ü
ACPI Suspend Type
This configuration responds the suspend mode to
operating system.
* S1 (POS): Power on Suspend
Chapter3 Award BIOS Setup
3 - 27
Full size CPU Card
SBC-860
* S3 (STR): Suspend to RAM
The choices: S1 (POS), S3 (STR), S1&S3
ü
Run VGA BIOS if S3 Resume
This feature assigns the OS to enable/disable/auto
running VGABIOS after resume from S3 mode.
The choices: Yes, No, Auto
ü
Power Management
Select Max Saving mode or Min Saving mode or define
desired Doze Mode, Standby Mode, Suspend Mode,
HDD Power Down functions by User Define.
This category allows you to select the type ( or
degree ) of power
saving and is directly related to the following
modes:
1. User Define
2. Min Saving
3. Max Saving
Disable
No power management. Disable
(Default)
all four modes.
Min. Power Minimum power management.
Saving
Chapter3 Award BIOS Setup
Suspend mode = 1 hour
3 - 28
Full size CPU Card
SBC-860
HDD Power Down =15 minutes.
Max.Power Maximum power management-Saving
ONLY
AVAILABLE FOR SL CPU'S.
Suspend mode = 1-2 min
HDD Power Down = 1
User
Allow you to set each mode
Defined
individually. When not disabled,
each of the tinges is from 1 min.
to 1 hour except for HDD Power
Down, which ranges from 1 min.
to 15 min. and disable.
ü
Video Off Method
This determines the manner in which the monitor is
blanked.
V/H SYNC+Blank: This selection will cause the system
to turn off the vertical and horizontal synchronization
ports and write blanks to the video buffer.
DPMS: Display power management system.
Blank Screen: This option only writes blanks to the
video buffer.
ü
Video Off In Suspend
After the selected period of system inactivity, the chipset
enters hardware suspend mode, stopping the CPU clock
Chapter3 Award BIOS Setup
3 - 29
Full size CPU Card
SBC-860
and possibly causing other system devices to enter
power management modes.
In this case the video hardware can be selected to shut
off after a period of system inactivity. This determines
the manner in which the monitor is blanked.
The choices: Yes, No
ü
Suspend Type
This item lets you select two types of suspend.
Stop Grant: Halts CPU’s instruction stream (stop clock)
at ACPI C2 state.
PwrOn Suspend: CPU sleeps at ACPI S1 state.
The choices: Stop Grant, PwrOn Suspend
ü
Modem Use IRQ
Name the interrupt request (IRQ) line assigned to the
modem (if any) on your system. Activity of the selected
IRQ always awakens the system.
The choices: NA, 3, 4, 5, 7, 9, 10, 11.
ü
Suspend Mode
Disable this function or select 1 min, 2 min, 4 min, 8
min, 12 min, 20min, 30 min, 40 min, 1 hour.
Please refer to power management section for more
information.
Chapter3 Award BIOS Setup
3 - 30
Full size CPU Card
ü
SBC-860
HDD Power Down
Disable this function or select from 1 to 15 minutes.
Please refer to power management section for more
information.
ü
Soft-Off by PWR-BTTN
If you select "Instant -Off", pushing the on/off button
will instantly shut down the system. If you select " Delay
4 sec", you have to push the on/off button lasting for 4
seconds to shut down the system. In this mode, one
touch on the on/off button won't shut down the system
but place it in a very low-power-usage state, with only
enough circuitry receiving power to detect power button
activity or Resume by Ring activity.
The choices: Instant-Off, Delay 4 Sec.
ü
Wake-Up by PCI Card
The Choices: Enabled, Disabled
ü
USB KB Wake-Up From S3
The choices: Enabled, Disabled
ü
Resume by Alarm
Enable this item to set up power up timer.
The Choices: Enabled, Disabled
ü
Date (of Month) Alarm
Chapter3 Award BIOS Setup
3 - 31
Full size CPU Card
ü
Time (hh:mm:ss) Alarm
ü
Reload Global Timer Events
SBC-860
When this item is enabled, an event occurring on each
listed device resets the global timer to prevent the
system from entering Suspend mode. These devices
include:
Primary/Secondary IDE 1/0, FDD/COM/LPT
Port, and PCI PIRQ[A-D]#.
Chapter3 Award BIOS Setup
3 - 32
Full size CPU Card
l
SBC-860
PnP/PCI Configuration
By choosing the PnP/PCI Configuration option from the
INITIAL SETUP SCREEN menu, the screen below is
displayed.
ü
PNP OS Installed
Select Yes if the system operating environment is Plug
and Play aware, for example Windows 9x, Windows
2000, and Windows XP. Hardware resource will be
distributed by OS.
Select No if you need the BIOS to configure non-boot
devices.
The choices: No, Yes.
Chapter3 Award BIOS Setup
3 - 33
Full size CPU Card
ü
SBC-860
Reset Configuration Data
Normally, you leave this field disabled. Select enabled to
reset Extended System Configuration Data (ESCD)
when serious conflict is caused by add-on device or
system reconfiguration.
The choices: Enabled, Disabled
ü
Resources Controlled By
The Award Plug and Play BIOS has the capacity to
automatically configure all the boot and Plug and Play
devices. If you choose Auto, you cannot select IRQ
DMA and memory base address fields, since BIOS
automatically assigns them.
The choices: Auto (ESCD), Manual.
ü
IRQ Resources
When resources are controlled manually, assign each
system interrupt a type, depending on the type of device
using the interrupt. There are two types for choice:
Legacy ISA and PCI/ISA PnP.
Legacy ISA: Devices compliant with the original PC
AT bus specification, requiring a specific interrupt (such
as IRQ4 for serial port 1)
PCI/ISA PnP: Devices compliant with the Plug and
Play standard, whether designed for PCI or ISA bus
Chapter3 Award BIOS Setup
3 - 34
Full size CPU Card
SBC-860
architecture.
ü
DMA Resources
When resources are controlled manually, assign each
DMA channel a type, depending on the type of device
using the DMA channel. There are two types for choice:
Legacy ISA and PCI/ISA PnP.
Legacy ISA: Devices compliant with the original PC
AT bus specification, requiring a specific DMA channel
PCI/ISA PnP: Devices compliant with the Plug and
Play standard, whether designed for PCI or ISA bus
architecture.
ü
PCI/VGA Palette Snoop
Enabling this item informs the PCI VGA card to keep
silent (and to prevent conflict) when palette register is
updated (i.e., accepts data without responding any
communication signals). This is useful only when two
display cards use the same palette address and plugged
in the PCI bus at the same time (such as MPEG or
Video capture card). In such case, PCI VGA is silent
while MPEG/Video capture card is set to function
normally.
The Choices: Enabled, Disabled
3.2.3 Default Setup
Chapter3 Award BIOS Setup
3 - 35
Full size CPU Card
l
SBC-860
Load Optimized Defaults
Select [Defaults] to Load Optimized Defaults setting from the
top menu, the screen shown below is displayed.
Pressing “Y” loads the default values that are factory settings for
optimal performance system operations.
When you press <Enter> on this item you get a confirmation
dialog box with a message similar to:
Load Optimized Defaults (Y/N)?
Pressing "Y" loads the default values that are factory settings for
optimal performance system operations.
Chapter3 Award BIOS Setup
3 - 36
Full size CPU Card
SBC-860
3.2.4 Security Setup
l
l
l
l
l
l
Set/Change password
You can set the password to restrict unauthorized access to
enter or change the options of the setup menus.
To abort the process at any time, press Esc.
NOTE: To clear the password, simply press Enter when asked
to enter a password. Then the password function is disabled.
Chapter3 Award BIOS Setup
3 - 37
Full size CPU Card
SBC-860
3.2.5 PC Health Setup
By choosing the [PC Health] option from the top menu, the screen below
is displayed.
l
Shutdown Temperature
You can set the shutdown temperature. When the temperature
of your system reaches the limitation, the system will shut down
automatically to prevent damage caused by overheat.
The choices: Disabled, 60℃/140℉, 65℃/149℉, 70℃/158
℉.
l
Power on show status
Enable this function to show hardware monitor listing after
powering on the system.
The choices: Enabled, Disabled
l
CPU fan low speed warning
Select the speed figure limits for the CPU speed. When CPU
Chapter3 Award BIOS Setup
3 - 38
Full size CPU Card
SBC-860
speed drop down to the limitation, the system would send out
the warning signal.
The choices: 2000RPM, 3000RPM, 4000RPM, Disabled.
Chapter3 Award BIOS Setup
3 - 39
Full size CPU Card
SBC-860
3.2.6 Clk/Voltage Setup
By choosing the [Clk/Voltage] option from the top menu, the screen
below is displayed.
l
CPU Clock Ratio
You may set the CPU Clock Ratio for your selection. However,
if the CPU you adopts reserves no flexibility for clock ratio
modification, this item will be hidden or can’t work.
The choices: 8X, 9X, … , 50X.
l
Auto Detect DIMM/PCI CLK
This item allows you to enable/disable auto detect DIMM/PCI
clock.
The choices: Enabled, Disabled.
l
Spread Spectrum
When the system clock generator pulses, the extreme values of
Chapter3 Award BIOS Setup
3 - 40
Full size CPU Card
SBC-860
the pulse generate excess EMI. Enabling pulse spectrum spread
modulation changes the extreme pulse spikes to flat curves thus
reducing EMI. This benefit may in some cases be outweighed by
problems with timing-critical devices, such as a clock-sensitive
SCSI device.
The choices: 0.25%, 0.50%, Disabled
Chapter3 Award BIOS Setup
3 - 41
Full size CPU Card
SBC-860
3.2.7 Exit Setup
l
Save & Exit Setup
If you select this option and press <Enter> from the top menu,
the values entered in the setup utilities will be recorded in the
chipset’s CMOS memory. The microprocessor will check this
every time you turn your system on and compare this to what it
finds as it checks the system. This record is required for the
system to operate.
l
Exit without saving
Selecting this option and pressing <Enter> lets you exit the
Setup program without recording any new values or changing
old ones.
Chapter3 Award BIOS Setup
3 - 42
F u l l - size CPU Card
SBC-860
4
Chapter
Driver
Installation
Chapter 4 Driver Installation
4-1
F u l l - size CPU Card
SBC-860
The SBC-860 comes with a CD-ROM which contains most of
drivers and utilities of your needs.
There are several installation ways depends on the driver package
under different Operating System application.
If you utilize Windows NT series OS, you are strongly
recommended to download the latest version Windows NT Service
Pack from Microsoft website and install it before installing any
driver.
Please follow the sequence below to install the drivers:
Step 1 – Install Intel INF Update for Windows 95-XP
Step 2 – Install Intel 845G Graphic Driver
Step 3 – Install Intel LAN Driver
Step 4 – Install Realtek 2CH AC97 codec Driver
For installation procedures of each driver, you may refer to section
4.1-4.3.
Chapter4 Drivers Installation
4-2
F u l l - size CPU Card
SBC-860
4.1 Installation 1:
Applicable for Windows 2000/98/ME/NT 4.0
1.
Insert the SBC-860 CD-ROM into the CD-ROM Drive.
2.
From the CD-ROM, select the desired component Driver
folder, select the desired Operation System folder to double
click on the Setup.exe icon. A driver installation screen will
appear.
(Notice: take VGA driver installation under Windows 98
for example, choose the corresponding folder depending
on your OS)
3.
A driver installation screen will appear, please follow the
onscreen instructions to install the driver in sequence and click
on the Next button.
(Notice: In some cases the system will ask you to insert
Windows 98 CD Diskette and key in its path. Then click
on the OK button to key in path.)
4.
Click on the Finish button to finish installation process. And
allow the system to reboot.
Chapter4 Drivers Installation
4-3
F u l l - size CPU Card
SBC-860
4.2 Installation 2:
Applicable for Windows 2000/ 98/ME
1.
Insert the SBC-860 CD-ROM into the CD-ROM Drive.
2.
Click on Start button, select the Settings, then click on the
Control Panel icon.
3.
Double click on the Add/Remove Hardware icon and Add
New Hardware Wizard will appear. Click on the Next
button.
4.
Select Search for the best driver for your device
(Recommended) and click on the Next button.
5.
Select Specify a location, click on Have Disk button then
key in the CD-ROM path and specify component drivers and
OS folders. Then click on the Next button.
6.
The Wizard shows that Windows driver file search for the
device. Click on the Next button.
7.
The system will ask you to insert Windows 98 CD Diskette.
Click on the OK button to insert Diskette and key in path.
8.
Click on the OK button.
9.
Click on the Finish button to finish installation process. And
allow the system to reboot.
Chapter4 Drivers Installation
4-4
F u l l - size CPU Card
SBC-860
4.3 Installation 3:
Applicable for Windows NT 4.0
1.
Insert the SBC-860 CD ROM into the CD-ROM Drive.
2.
Start system with Windows NT 4.0 installed.
IMPORTANT: When the "Please select the operating system
to start..." message is displayed, select "Windows NT
Workstation Version 4.00 [VGA mode]".
3.
From Start, select the Settings group, then click on the
Control Panel icon.
4.
In the Control Panel, select the desired device and click on
the icon.
5.
Follow the step-by-step instruction and click on OK button.
6.
Click on the Have Disk... button.
7.
Key in CD-ROM path and specify component drivers, then
click on the OK button.
8.
From the list of displayed devices, select your desired device.
9.
If a message appears stating the driver is already installed on
the system, and asks if you want to use the current or new
drivers, be sure to select the New button.
10. If prompted for the driver diskette a second time, click on the
Continue button.
(Notice: In some cases the system will ask you to insert
Windows NT CD ROM. Follow its instructions to
complete the setup procedures.)
11. When the message “The drivers were successfully
installed” is displayed, remove the display driver diskette, then
click on the OK button.
12. Reboot the system.
Chapter4 Drivers Installation
4-5
F u l l - size CPU Card
SBC-860
A
Appendix
Programming the
Watchdog Timer
Appendix A Programming the Watchdog Timer
A-1
F u l l - size CPU Card
SBC-860
A.1 How to program the watchdog timer
SBC-860 utilizes ITE 8712 chipset as its watchdog timer controller.
Please follow the procedures below to complete its configuration.
1. Enter the MB PnP mode
2. Select logical device
3. Configure the watchdog timer controller registers
4. Exit the MB PnP mode
To enter the MB PnP mode is to write value 87h, 1h, 55h, 55h to
configuration port - 2Eh.
To exit the MB PnP mode is to set bit 1 of configure control
register (index 02h) to 1.
The AAEON initial watchdog timer program is illustrated below.
This program is applied only to DOS and Win 9x.
Example :
;============================ =======
; Enter the MB PnP mode
;============================ =======
mov
al, 87h
out
2eh, al
mov
al, 1
out
2eh, al
Appendix A Programming the Watchdog Timer
A-2
F u l l - size CPU Card
mov
al, 55h
out
2eh, al
mov
al, 55h
out
2eh, al
SBC-860
;============================ =======
; Select logical device
;============================ =======
mov
al, 7
out
2eh, al
mov
al, 7
out
2fh, al
;index 7 for logical device
;============================ =======
; Configure the watchdog timer controller registers
;============================ =======
mov
al, 73h
out
2eh, al
mov
al, 0ah
out
2fh, al
mov
al, 72h
out
2eh, al
mov
al, 0c0h
out
2fh, al
Appendix A Programming the Watchdog Timer
;index 73h for watchdog timer
time-out value
;time-out value use second &
enable WDT output through
KRST
A-3
F u l l - size CPU Card
SBC-860
;============================ =======
; Exit the MB PnP mode
;============================ =======
mov
al, 2
out
2eh, al
out
2fh, al
Appendix A Programming the Watchdog Timer
A-4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement