Sigma FireWire 800+Hi-Speed USB Combo

Sigma FireWire 800+Hi-Speed USB Combo
FireWire 800+Hi-Speed
USB Combo
Quick Installation Guide
Introducing the FireWire 800+Hi-Speed
USB Combo
The FireWire 800 + Hi-Speed USB Combo features the latest
technology in FireWire 800 and USB 2.0.
Features and Benefits
•
•
•
Combo card design adds five USB 2.0 (480 Mbps),
one 1394a (400Mbps) and two 1394b (800 Mbps)
ports into your system.
Built-in 4-pin power connector provides extra power
when connected to the system's power supply
(Recommended)
Supports hot-swapping and Plug-n-Play connection
of peripheral devices
FireWire 800 (1394b) interface
•
Provides 3 FireWire ports for multiple 1394b and
1394a device connections
•
Adds two FireWire 800 (1394b) ports (1 int. + 1 ext.)
and one external 1394a (400Mbps) port
•
Supports IEEE 1394b and backwards compatible
with 1394a-2000 and 1394-1995 standards
•
Supports data transfer rates of 100, 200, 400, and
800Mbps
04-0348B
1
USB 2.0 interface
•
Adds two external and three internal USB 2.0 ports
(two internal via USB Pin-out Header, see page 4)
•
Compliant with USB specification rev. 2.0
•
Supports high-speed (480 Mbps), full-speed (12
Mbps), and low-speed (1.5 Mbps) data transfer
modes for simultaneous operation of multiple USB
2.0/1.1 devices
Note: USB 1.1 devices are limited to USB 1.1 speeds
even when they are connected to USB 2.0 host adapter
or USB 2.0 hubs.
System Requirements
PC:
•
Pentium or equivalent computer with an available
PCI slot
•
Windows 98SE/ME/2000/XP/Server 2003
MAC:
•
Power Mac G3 Blue & White or later with an available
64-bit or 32-bit PCI slot
•
Mac OS 8.6 or later
- Requires Mac OS X (v10.2.4) or later for FireWire
800 speed
- Requires Mac OS X (v10.1.3) or later for USB 2.0
speed
Package Contents
•
•
•
•
2
FireWire 800+Hi-Speed USB Combo adapter
"Y" split power cable
Driver CD
Quick Installation Guide
Board Layout
1394b (9-pin)
1394a (6-pin)
USB Pin-out
Header
1394b (9-pin)
USB 2.0
Power Connector
(recommended)
USB 2.0
Figure 1. Board Layout
Note: The Power Connector (same as the one used
with your floppy disk drive) is designed to provide
additional power to the board when needed.
Connect this power connector (recommended) when
one of the following conditions occur:
- Device(s) not being detected.
- All ports are used.
Power off your system first before making this
connection.
3
USB Pin-out Header
The USB pin-out header consists of 9 pins arranged in 2
rows, it allows for 2 USB connections (i.e. USB4 and
USB5). Normally, the pins for each port are in seperate
rows.
USB2
Pin Assignments
USB1
Red
+ 5VDC
+5VDC
White
DATA -
DATA -
Green
DATA +
DATA +
Black
GND
GND
S-GND
Figure 2. USB Pin-out Header
Note: The pin-out header is designed to connect to
front mounted USB ports, flash memory card
readers, or any USB devices that require pin-out
header. Reference the image above and review
your computer's manual for proper connection.
4
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1.
2.
3.
4.
5.
Turn OFF the power to your computer and any
other connected peripheral devices. Unplug the
computer's power cord.
Remove your computer’s cover and install the card
in an available PCI slot.
Push the board down firmly, but gently, until it is
well seated.
Connect internal connections where needed. See
Board Layout on page 3 for more details.
Secure the card and replace the cover.
Figure 3. Inserting the PCI Board
5
Windows Driver Installation
To ensure proper installation of this board, please follow
the instructions step-by-step.
Windows 98SE
1.
Install the board, boot up Windows, and insert the
driver CD.
2.
At the Add New Hardware Wizard, click Cancel.
3.
Click Start, then Run. Type X:\Windows\USB2.exe
and click OK. (Change X: to match your CD-ROM
drive letter)
4.
Select Yes, I want to restart my computer now, click
Close.
5. When Windows resumes, at the Add New Hardware
Wizard, click Next.
6.
Select Search for the best driver for your device.
(Recommended), click Next.
7.
Uncheck all check boxes, then click Next.
8. Click Next, then Finish.
9.
At the Add New Hardware Wizard, click Next.
10. Select Display a list of all drivers..., click Next.
11. Click Have Disk..., type X:\Windows, click OK.
(Change X: to match your CD-ROM drive letter)
12. Click Next, Next, then Finish.
Note: If prompted for Windows 98SE Installation
CD, click OK. Insert this CD and click OK.
13. Repeat steps 9, 6, 7, and 12 respectively.
14. Repeat step 13.
15. Restart the computer to complete the installation.
6
Windows ME
1.
2.
3.
4.
5.
6.
7.
8.
9.
Install the board, boot up Windows, and insert the
driver CD.
At the Add New Hardware Wizard, click Cancel.
Click Start, then Run. Type X:\Windows\USB2.exe
and click OK. (Change X: to match your CD-ROM
drive letter)
Restart Windows after the driver installation
completes.
When Windows resumes, at the Add New Hardware
Wizard, select Automatic search for a better driver
(Recommended), click Next, then click Finish.
At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced), click Next.
Check Specify a location, uncheck the other box,
type X:\Windows, then click Next. (Change X: to
match your CD-ROM drive letter)
Click Next, Next, then Finish.
Click Yes to restart Windows to complete the
installation.
Windows 2000
For Windows 2000 w/SP3 or earlier
1.
2.
3.
Install the board, boot up Windows, and insert the
driver CD.
At the Found New Hardware Wizard, click Cancel.
Click Start, then Run. Type X:\Windows\USB2.exe
and click OK. (Change X: to match your CD-ROM
drive letter)
7
4.
5.
6.
7.
8.
9.
Right click My Computer, click Manage, then click
Device Manager.
Click the plus (+) sign next to IEEE 1394 Bus host
controllers, then double click Texas Instruments
OHCI... 1394 Host Controller.
Click the Driver tab, click Update Driver..., then
click Next.
Select Search for a suitable driver for my device
(recommended), click Next.
Check CD-ROM drives, uncheck the other boxes,
then click Next.
Click Next, then Finish. Restart the computer to
complete the installation.
For Windows 2000 w/SP4 or later
Windows installs built-in USB 2.0 and 1394a drivers.
However, to get the full speed from the 1394 interface,
install the FireWire 800 driver from the included driver
CD. Follow the steps in the order that they appear.
1.
2.
3.
4.
5.
8
Install the board, boot up Windows, and insert the
driver CD.
Right click My Computer, click Manage, then click
Device Manager.
Click the plus (+) sign next to IEEE 1394 Bus host
controllers, then double click Texas Instruments
OHCI... 1394 Host Controller.
Click Driver tab, click Update Driver..., then click
Next.
Select Search for a suitable driver for my device
(recommended), then click Next.
6.
7.
Check CD-ROM drives, uncheck the other boxes,
then click Next.
Click Next, then Finish. Restart the computer to
complete the installation.
Windows XP/Server 2003
For Windows XP without SP1
1.
Install the board, boot up Windows, and insert the
driver CD.
2.
At the Found New Hardware Wizard, click Cancel.
3.
Click Start, then Run. Type X:\Windows\USB2.exe
and click OK. (Change X: to match your CD-ROM
drive letter)
4. At the Found New Hardware Wizard, select Install
the software automatically (Recommended), click
Next, then click Finish.
5.
Right click My Computer, click Manage, then click
Device Manager.
6.
Click the plus sign (+) next to IEEE 1394 Bus host
controllers, then double-click Texas Instruments...
Host Controller.
7. Click the Driver tab, click Update Driver..., select
Install from a list or specific location (Advanced),
then click Next.
8.
Check Don't search. I will choose the driver to
install, then click Next.
9.
10.
Click Have Disk..., type X:\Windows, then click
Ok. (Change X: to match your CD-ROM drive
letter)
Select OHCI IEEE 1394b Host Controller, click Next.
9
11.
Click Continue Anyway, then click Finish to
complete the installation. Our driver has been
thoroughly tested in Windows for stability.
For Windows XP w/SP1 or later and Server 2003
Windows XP with SP1 and Server 2003 automatically
install built-in USB 2.0 and 1394a drivers. However, to
get the full speed from the 1394 interface, install the
FireWire 800 driver from the included driver CD. Follow
the steps in the order that they appear.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10
Install the board, boot up Windows, and insert the
driver CD.
Right click My Computer, click Manage, then click
Device Manager.
Click the plus sign (+) next to IEEE 1394 Bus host
controllers, then double-click Texas Instruments...
Host Controller.
Click the Driver tab, click Update Driver..., select
Install from a list or specific location (Advanced),
then click Next.
Check Don't search. I will choose the driver to
install, then click Next.
Click Have Disk..., type X:\Windows, then click
OK. (Change X: to match your CD-ROM drive
letter)
Select OHCI IEEE 1394b Host Controller, then click
Next.
Click Continue Anyway. Our driver has been
thoroughly tested in Windows for stability.
Click Finish. Restart Windows to complete the
installation.
To Verify Windows Installation
1.
Check Device Manager to verify successful driver
installation.
Windows 98SE/ME: From the main desktop, right
click My Computer, then click Properties. Click
Device Manager tab.
Windows 2000/XP/Server 2003: Right click My
Computer, then click Manage. Click Device
Manager.
2.
The drivers for this controller show up differently
under different versions of Windows. Please refer
to the correct Windows version to verify.
Windows 98SE/ME:
a) Under the Universal Serial Bus Controllers:
- NEC PCI to USB Enhanced Host Controller
- USB 2.0 Root Hub Device
- NEC USB Open Host Controller...
- NEC USB Open Host Controller...
- USB Root Hub
- USB Root Hub
b) Under 1394 Bus Controller or IEEE 1394 Bus host
controllers:
- OHCI IEEE 1394b Host Controller
Windows 2000 (with SP4 or later):
a) Under the Universal Serial Bus Controllers:
- NEC... Open Host Controller
- NEC... Open Host Controller
- Standard Enhanced PCI to USB Host Controller
- USB 2.0 Root Hub
11
- USB Root Hub
- USB Root Hub
b) Under IEEE 1394 Bus host controllers:
- OHCI IEEE 1394b Host Controller
Windows 2000 (with SP3 or earlier) and XP (without
SP1):
a) Under the Universal Serial Bus Controllers:
- NEC PCI to USB Open Host Controller
- NEC PCI to USB Open Host Controller
- NEC PCI to USB Enhanced Host Controller
- USB 2.0 Root Hub Device
- USB Root Hub
- USB Root Hub
b) Under IEEE 1394 Bus host controllers:
- OHCI IEEE 1394b Host Controller
Windows XP (with SP1 or later)/Server 2003:
a) Under Universal Serial Bus Controllers:
- NEC PCI to USB Open Host Controller
- NEC PCI to USB Open Host Controller
- Standard Enhanced... USB Host Controller
- USB Root Hub
- USB Root Hub
- USB Root Hub
b) Under IEEE 1394 Bus host controllers:
- OHCI IEEE 1394b Host Controller
12
Mac OS Driver Installation
The instructions below are divided into two sections,
FireWire 800 and USB 2.0. To ensure proper installation
of this board, please follow the instructions step-by-step
in both sections.
FireWire 800 Driver Installation
To ensure proper operation of the FireWire 800+Hi-Speed
USB Combo in your Mac, some Mac OS requires the most
current Firewire software from Apple.
Apple's website contains all the information needed to
download and install Firewire software update. Mac
software download URL is: http://www.info.apple.com/
support/downloads. When you are at the download
page, in the Search box, check Restrict to downloads,
type in 1394, then click GO.
The information below will help you decide whether or
not to download and install the latest Firewire driver
update.
1.
2.
3.
4.
Mac OS 10.2.4 or later has built-in Firewire 800
(1394b) driver support with the operating system.
No driver installation is needed. The firewire 800
ports will work up to 800 Mbps.
Mac OS 9.1, 9.2.x, and Mac OS 10.1.x-10.2.3 have
built-in Firewire 400 (1394a) driver support with the
operating system. No driver installation isneeded.
The Firewire 800 ports will work up to 400 Mbps.
Mac OS 9.0.x users should download the Firewire
software version 2.5 or later. The Firewire 800 ports
will work up to 400 Mbps.
Mac OS 8.6 users should download the Firewire
software version 2.3.3. The Firewire 800 ports will
work up to 400 Mbps.
13
USB 2.0 Driver Installation
Mac OS 8.6-9.x
This board will only work at USB 1.1 speed in these OSes.
Just install the board and Mac OS will automatically
detect and install the correct USB 1.1 driver for it. No
additional driver is necessary.
Mac OS X (version 10.1.3-10.1.5)
Note: Mac OS X (version 10.1.3-10.1.5) driver version
does not support USB 2.0 hubs.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Install the board and boot up your system.
Insert the driver CD.
Double click the Drivers CD icon on your desktop.
At the new window, double click OS10.15.
Double click v108.img, then double click the
USB2EHCI_v108 disk icon that appears on the
desktop.
At the next window, double click USB2EHCI_v108
to start installation.
At the Authorization window, click the lock icon,
enter your administrator password, and click OK.
Click Continue. When prompted to select the
destination disk to install the USB 2.0 driver, choose
the disk where your Mac OS is installed, and click
Continue.
Click Install, Continue Installation, and Restart to
complete the installation.
Mac OS X (version 10.2.3-10.2.6)
1.
Install the board and boot up your system.
2.
Insert the driver CD.
14
3.
4.
5.
6.
7.
8.
Double click the Drivers CD icon on the desktop.
At the new window, double click OS10.2x.
At the next window, double click
USB2EHCI_v3_1_5.pkg to start the installation.
At the Authorization window, click the lock icon,
enter your administrator password, and click OK.
Click Continue. When prompted to select the
destination disk to install the USB 2.0 driver, choose
the disk where your Mac OS is installed, then click
Continue.
Click Install, Continue Installation, and Restart to
complete the installation.
Mac OS X (version 10.2.8 ) or later
Mac OS X (version 10.2.8) or later have built-in driver
support for this controller. Just install the board and Mac
OS will automatically detect and install the correct drivers
for it. No additional driver is necessary.
To Verify Mac OS Installation
Mac OS 8.6, 9.x, X (version 10.0-10.1)
Since we didn't load any additional driver under these
Mac OSes, plug in a USB device to verify installation.
Mac OS X (version 10.1.3-10.1.5)
1.
Double click OS 10.1x volume/drive icon.
2. Go to System/Library/Extensions folder.
3. If the file OMI_EHCI.kext is in the Extensions folder,
the USB 2.0 driver is installed successfully.
15
Mac OS X (version 10.2.3-10.2.6)
1.
Double click OS 10.2x volume/drive icon.
2. Go to System/Library/Extensions folder.
3.
If the following files are in the Extensions folder, the
USB 2.0 driver is installed successfully.
- OMI_EHCI.kext
- OMI_USBHub.kext
Mac OS X (version 10.2.8) or later
Since we didn't load any additional driver under these
Mac OSes, plug in a USB device to verify installation.
16
Technical Support and Warranty
QUESTIONS?
SIIG’s Online Support has answers!
Simply visit our website at www.siig.com and click on Support.
Our online support database is updated daily with new drivers
and solutions. Answers to your questions could be just a few clicks
away. You can also submit questions online and one of our technical
support analysts will promptly respond.
A lifetime manufacturer warranty supplied with this product is
offered by SIIG, Inc. Please see SIIG website for more warranty
details. If you should happen to encounter any problems with this
product, please follow the procedures below.
If it is within the store's return policy period, please return the
product to the store where you purchased from.
If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued. SIIG RMA department
can also be reached at (510)413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping the product to SIIG
at the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S and International Economy outside of the U.S at
no cost to the customer.
17
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer
of I/O connectivity products, including PCI & ISA serial and parallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
Networking, Sound Cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIG products offer comprehensive user manuals, many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, and e-commerce
sites in the Americas and the UK, as well as through major distributors,
system integrators, and VARs.
PRODUCT NAME
FireWire 800+Hi-Speed USB Combo
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
FireWire 800+Hi-Speed USB Combo is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation.
Mac and Mac OS are registered trademarks of Apple Computer, Inc. Other names used in this
publication are for identification only and may be trademarks of their respective companies.
April, 2005
Copyright ©2005 by SIIG, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement