Sigma Firewire 800 NN831012S2

Sigma Firewire 800 NN831012S2
FireWire 800 DV Kit
Quick Installation Guide
Introducing the FireWire 800 DV Kit
The FireWire 800 DV Kit is designed to add FireWire 800
(1394b) and 1394a (6-pin) interfaces to your computer.
For your convenience, one FireWire (1394a) 6-pin/4-pin
DV cable is included for connecting DV camcorders and
other 1394 devices using 4-pin connector. Ulead
VideoStudio video editing software is also included for
producing greeting cards, video e-mails, or home videos
complete with attractive titles, effects, and background
music.
Features and Benefits
•
•
•
•
•
•
Provides 2 FireWire 800 (1394b) ports and 1 1394a
(6-pin) port for multiple 1394b/1394a device
connections
Supports data transfer rates of 100, 200, 400 and
800Mbps
Built-in 4-pin power connector provides extra power
when connected to the system's power supply
(Recommended)
Supports hot-swapping and Plug-n-Play connection
of peripheral devices
Includes one spare low profile bracket for systems
with low profile chassis
Works with various types of FireWire 800 (1394b)
and 1394a devices including portable hard disk, DV
camcorder, digital camera, CD-RW/DVD-ROM
drive and other audio/video devices
04-0316B
1
System Requirements
•
•
Pentium or equivalent PC with an available 32-bit
or 64-bit PCI slot
Windows 98SE/ME/2000/XP/Server 2003
Recommended system for DV capturing/editing:
•
Pentium III or above PC computer
•
128 MB RAM and CD-ROM drive
•
4 GB of available hard drive space
•
Video card with a minimum of 4 MB RAM
Package Contents
•
•
•
•
•
•
2
FireWire 800 32-bit PCI board
Spare Low Profile bracket (for Low Profile chassis)
1394a 6-pin to 4-pin DV cable
Deluxe Ulead VideoStudio DV editing software
Driver CD
This quick installation guide
Board Layout
4-Pin Power
Connector
Firewire Port
(1394a)
Firewire 800
Ports
Figure 1. Board Layout
Hardware Installation
Note: For Low Profile systems, replace the currently
mounted bracket with with the included Low Profile
bracket.
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1.
2.
Turn OFF the power to your computer and any
other connected peripheral devices. Unplug the
computer's power cord.
Remove your computer’s cover and install the card
in an available PCI slot.
3
3.
4.
5.
Push the board down firmly, but gently, until it is
well seated.
Connect an available 4-pin power connector from
the system power supply to the 4-pin power
connector on the FireWire 800 32-bit PCI board (See
Figure 1 on page 3). This connection is recommended
for reliable power output.
Secure the card and replace the cover.
Software Installation
This section provides information on how to install the
FireWire 800 32-bit PCI drivers. Please follow the directions
below for your operating system.
Windows Driver Installation
Windows 98SE
1.
At the Add New Hardware Wizard, click Next.
2.
Select Search for the best driver for your device
(Recommended), then click Next.
3. Insert the driver CD, check CD-ROM drive, uncheck
the other boxes, then click Next.
4. Click Next, then Next again.
5.
If prompted for the Windows 98SE CD, insert it, then
click OK.
6.
Click Finish and restart Windows to complete the
installation.
Windows ME
1. At the Add New Hardware Wizard, insert the driver
CD, select Automatic Search for a better driver,
click Next, then click Finish.
2.
Click Yes to restart to complete the installation.
4
Windows 2000
Windows 2000 automatically installs it's built-in 1394a
driver for the FireWire 800 PCI-32T. To get the full speed
out of this controller, install the Firewire 800 driver using
the directions below.
1.
Right click My Computer, click Manage, then click
Device Manager.
2.
Double click IEEE 1394 Bus host controller, then
double click Texas Instruments OHCI Compliant
IEEE 1394 Host Controller.
3.
Click the Driver tab, then Update driver button.
4.
At the Upgrade Device Driver Wizard, click Next.
5.
Select Search for a suitable driver for my device,
then click Next.
6.
Insert the driver CD, check CD-ROM drives, then
click Next.
7.
Click Next, then click Finish.
8.
Restart Windows to complete the installation.
Windows XP/Server 2003
Windows XP and Server 2003 automatically installs it's
built-in 1394a driver for the FireWire 800 PCI-32T. To get
the full speed out of this controller, install the Firewire
800 driver using the directions below.
1.
Right click My Computer, click Manage, then click
Device Manager.
2.
Double click IEEE 1394 Bus host controller, the
double click Texas Instruments OHCI Compliant
IEEE 1394 Host Controller.
3.
Click the Driver tab, then Update Driver button.
4.
Select Install from a list or specific location, then
click Next.
5
5.
6.
7.
8.
9.
10.
Select Don't search. I will choose the driver to
install, then click Next.
Insert the driver CD, click Have disk.
Type in D:, then click OK. (Change D: to match your
CD-ROM drive letter)
Select OHCI IEEE 1394b Host Controller, then click
Next.
Click Continue Anyway. Our driver has been
thoroughly tested in Windows for stability.
Click Finish. Restart Windows to complete the
installation.
Verify Proper Installation in Windows
1.
Check Device Manager to verify successful
installation.
Windows 98SE/ME: From the main desktop, right
click My Computer, then click Properties. Click
Device Manager tab.
Windows 2000/XP/Server 2003: Right click My
Computer, then click Manage. Click Device
Manager.
2.
Double click 1394 Bus Controller or IEEE 1394 Bus
host controllers.
- An OHCI IEEE 1394b Host Controller should be
displayed.
6
Ulead VideoStudio Software Installation
The FireWire 800 DV Kit includes Ulead® VideoStudioTM
digital video editing software for producing home videos,
complete with attractive titles, transitions and sounds.
Before installing VideoStudio, make sure your adapter
and DV camcorder are properly installed and configured.
See next section, Connecting DV Camcorder, for more
details on how to properly install your DV camcorder.
1.
2.
Insert the Ulead VideoStudio DV software CD.
Auto-run should start automatically. If not, click
Start, Run, type in X:\Autorun.exe, then click OK.
(Replace X: with the drive letter of your CD-ROM)
Choose Install Ulead VideoStudio and follow
on-screen instructions to complete installation.
Note: For instructions on how to use Ulead
VideoStudio, please refer to VStudio.pdf file
located in the Manual directory on the Ulead
VideoStudio DV software CD.
Connecting DV Camcorder
Before setting up the digital video camcorder, make sure
to verify the driver for the adapter has been successfully
installed in your system and follow the setup procedures
listed below.
1.
Boot up your system.
2. Connect the 4-pin connector of the provided
FireWire (1394a) 6-pin/4-pin DV cable into your
digital camcorder, and connect the 6-pin connector
into an available port on the 1394 adapter. Power on
the camcorder. The camcorder should now appear
in Device Manager.
7
To verify successful DV Camcorder setup
1.
2.
8
Check Device Manager to verify successful driver
installation.
Windows 98SE/ME: From the main desktop, right
click My Computer, then click Properties. Click
Device Manager tab.
Windows 2000/XP/Server 2003: Right click My
Computer, click Manage, then click Device
Manager.
Double click Imaging Device(s), and Microsoft DV
Camera and VCR or DV Camcorder should be
displayed.
Technical Support and Warranty
QUESTIONS?
SIIG’s Online Support has answers!
Simply visit our website at www.siig.com and click on Support.
Our online support database is updated daily with new drivers
and solutions. Answers to your questions could be just a few clicks
away. You can also submit questions online and one of our technical
support analysts will promptly respond.
A lifetime manufacturer warranty supplied with this product is
offered by SIIG, Inc. Please see SIIG website for more warranty
details. If you should happen to encounter any problems with this
product, please follow the procedures below.
If it is within the store's return policy period, please return the
product to the store where you purchased from.
If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued. SIIG RMA department
can also be reached at (510)413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping the product to SIIG
at the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S and International Economy outside of the U.S at
no cost to the customer.
9
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer
of I/O connectivity products, including PCI & ISA serial and parallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
Networking, Sound Cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIG products offer comprehensive user manuals, many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, and e-commerce
sites in the Americas and the UK, as well as through major distributors,
system integrators, and VARs.
PRODUCT NAME
FireWire 800 DV Kit
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
FireWire 800 DVKit is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation.
Other names used in publication are for identification only and may be trademarks
of their respective companies.
March, 2005
Copyright ©2005 by SIIG, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement