Yamaha | WXAD-10 | Owner’s Manual | Wireless Streaming Adapter

Wireless Streaming Adapter
OWNER’S MANUAL
Before using this unit, be sure to read the “Safety Brochure.”
EN
Table of Contents
Accessories
Accessories .......................................................................................... 2
• AC adaptor
* The shape of the AC adaptor may vary depending
on the area purchased.
About this manual ................................................................................ 2
Using this product ................................................................................ 3
WXAD-10 ........................................................................................................3
MusicCast CONTROLLER: an app that lets you enjoy MusicCast .................3
• Power cord
Part Name .............................................................................................. 4
Front/Bottom ...................................................................................................4
Rear ................................................................................................................4
• RCA stereo cable
Setup ..................................................................................................... 5
Playback ................................................................................................ 7
Listening to the music stored on the mobile device ........................................7
Listening to the Internet radio .........................................................................7
Listening to music stored on your PC or NAS .................................................8
Listening to the music via AirPlay ...................................................................9
Listening to the music via Bluetooth .............................................................10
• 3.5 mm stereo mini plug cable
Configuring the MusicCast network ..................................................12
Registering supported devices to the app ....................................................12
About this manual
Other functions and information .......................................................13
Optional settings ...........................................................................................13
Updating the firmware ..................................................................................14
Sharing the iPhone settings and connecting to a network ............................15
• In this manual, smartphones and other mobile devices with iOS or Android are
collectively referred to as “mobile devices.”
• The term “iPhone” as used in this manual also refers to an “iPod touch” or
“iPad.”
• Illustrations in this manual may differ slightly from actual object depicted.
• MusicCast CONTROLLER app screen shots in this manual show the iOS
interface in English. The screen appearance may vary depending on the app
version.
• About symbols
Troubleshooting ..................................................................................16
General .........................................................................................................16
MusicCast .....................................................................................................17
Network ........................................................................................................17
Bluetooth ......................................................................................................19
Supported devices/media and file formats ...................................... 20
Specifications ..................................................................................... 21
Note
Trademarks ......................................................................................... 22

2
Indicates precautions and supplementary information for use
of the unit.
Indicates the corresponding reference page(s) that describe
related information.
Using this product
WXAD-10
MusicCast CONTROLLER: an app
that lets you enjoy MusicCast
You can listen to music from anywhere in your home using MusicCast.
MusicCast is a feature that enables you to share and play music on multiple
audio devices located in different rooms.
This product is a streaming adapter that can be controlled via MusicCast
CONTROLLER. By connecting this adapter to an audio device that does not
support network functions, you can easily enjoy audio streaming services. In
addition, you can configure a home audio network by connecting this product to
other MusicCast-compatible devices.
For more information on home audio networks, refer to “Configuring the
MusicCast network” ( P. 12).
Using the free app “MusicCast CONTROLLER” on your mobile device, you can
enjoy music in several ways, such as listening to an Internet radio station
simultaneously on multiple MusicCast-compatible devices, or playing music files
stored on your mobile device, PC, or on a server, such as a Network-Attached
Storage (NAS) device.
For more information on “MusicCast CONTROLLER” (called “app” elsewhere in
this manual), visit the following website.
http://www.yamaha.com/musiccast/
Note
• To use the app, a wireless LAN environment is required.
• Download the app from the App Store or Google Play.
3
Part Name
Rear
Front/Bottom
7
8
9
j
k
1 2 3
1 Bluetooth indicator ( P. 10)
2 Power indicator
Lights while the unit is turned on.
3 Wi-Fi indicator ( P. 6)
4 OPTION ( P. 13)
5 CONNECT ( P. 6)
6 A (Power) ( P. 13)
4
5
7 AUX OUT jack (Stereo mini jack) ( P. 5)
6
8 LINE OUT jack (RCA jack) ( P. 5)
9 Service jack
This jack is used for servicing and maintenance. Do not remove the attached
cap.
j NETWORK terminal ( P. 6)
k DC IN (for power supply) ( P. 5)
4
Setup
1 Connect such as powered speakers or mini component.
Use the supplied 3.5 mm stereo mini plug cable or RCA stereo cable to
connect such as powered speakers or a mini component to this unit.
Depending on your audio device, select jack [AUX OUT] or [LINE OUT]. For
more information, please also refer to the owner’s manual for the connecting
device.
Note
• Before you start to make connections, lower the volume level on the connecting
device.
• If you use both [LINE OUT] and [AUX OUT] jacks, the audio from the [AUX OUT] will
be output.
• If you use the [AUX OUT] jack, you will be able to adjust the audio level from the
app.
2
1
3.5 mm stereo
mini plug cable
RCA stereo
cable
Power cord
2 Connect the AC adaptor and Power cord.
3
Connect the supplied Power cord and AC adaptor to the unit.
Note
The Power cord is provided for this unit only. It cannot be used for data
communication. Be sure to use it to supply power.
AC adaptor
3 Connect the AC adaptor to the AC outlet.
First, connect the Power cord and the AC adaptor to the unit, and then
connect the AC adaptor to the AC outlet.
Powered
speakers, etc.
5
Mini component, etc.
Setup
4 Connect to the network.
Download and install the MusicCast CONTROLLER app to your mobile
device from the App Store or Google Play. Once you start the app, follow the
instructions in the app to complete the settings.
Note
• For a LAN cable connection, connect a commercially-available STP (shielded
twisted pair) network cable (straight, CAT-5 or higher) to the [NETWORK] terminal on
the rear panel.
• If your router supports multiple SSIDs (network names), connect the mobile device
to the primary SSID network (Primary SSID, 1st SSID, etc.).
• For more information about Internet connections, please refer to the instruction
manual supplied with your network device.
• The unit may not be able to access your personal computer or Internet radio station
due to security software or network device settings (such as a firewall). In this case,
change the settings on the security software or the network device.
1
Setup
3
WXAD-10
[Bottom panel]
Auto standby
This unit automatically engages standby mode if you do not operate it for 20
minutes while the playback is stopped. You can change this setting using
MusicCast CONTROLLER. On the room selecting screen, tap [
and change the setting.
2
Hold down the [CONNECT]
button for five seconds.
(Settings)]
[Front panel]
Indicator
When the Power indicator
turns from flashing to lit,
proceed to the next operation.
6
Playback
You can play back music using MusicCast CONTROLLER. Select a room that the
unit registered to open the Sources menu screen.
Listening to the music stored on the
mobile device
Note
To listen to the playback of music, you must switch the input source on the audio device
connected to the unit. Refer to the instruction manual for the audio device on how to switch
the input source.
1
A room that
the unit
registered
You can play music files stored on the mobile device on which you installed the app.
2
A (Power)
Music file
Sources
menu
screen
Playback
starts.
1
Mobile device
2
Tap
Listening to the Internet radio
You can listen to world-wide radio stations via the Internet.
2
1
Net Radio
Select
Select a radio
station.
Note
• Some Internet radio stations may be unavailable at all times or during certain hours.
• This service may be interrupted without advance notice.
• The unit uses the airable.Radio service. “airable” is a service of Tune In GmbH.
7
Playback
Listening to music stored on your PC or NAS
You can play music files stored on your network-connected PC, or on a Digital
2 Play back your music files.
Living Network Alliance (DLNA)-compatible NAS.
Note
2
• Connect the unit and your PC (or NAS) to the same wireless LAN router (access point).
• For information on music files that can be played using the unit, please refer to
“Supported devices/media and file formats” ( P. 20).
Music file
Playback
starts.
1 Set up sharing for music files
To play music stored in the PC (or NAS), you must enable media sharing
between this unit and other devices. The following instructions use Windows
Media Player 12 as an example.
1
Server
Follow the screens below to set up media sharing.
Note
• These screen images show the English interface.
• If you are using a PC (or NAS) that runs DLNA server software other than Windows
Media Player, please refer to the instruction manual for your device or software to
configure media sharing.
Windows Media Player 12
1
2
3
Click the “Allowed”
for this unit.
xxxxxx
4
WXAD-10
5
8
Playback
Listening to the music via AirPlay
You can use the AirPlay function to play back iTunes or iPhone music files.
Note
• Connect the unit and the PC (or iPhone) to the same wireless LAN router (access point).
• For information on supported iPhones, please refer to “Supported devices/media and
file formats” ( P. 20).
1 Start iTunes, or display the playback screen on the iPhone.
Icon indication example in iTunes
When the iTunes or iPhone detects the unit, the AirPlay icon will appear on
the screen (see the illustrations on the right).
Note
• If you are using iOS 9, the icon will appear in the Control Center. To display the
control center, swipe the iPhone screen from bottom to top.
• If the icon does not appear, check to see whether the unit and the PC (or iPhone) are
correctly connected to the wireless LAN router.
Icon indication example on the iPhone
iOS 10
2 In iTunes or on the iPhone, click or tap the AirPlay icon,
and select the unit (the room that the unit registered) as the
audio output destination.
3 Play back your music files.
The unit’s input source will be switched and the playback will start.
9
iOS 9
Playback
Listening to the music via Bluetooth
You can play music that resides on mobile devices or digital music players that
supports Bluetooth (Bluetooth devices). In addition, you can listen to music that
is being played back via the unit through speakers or headphones that support
Bluetooth.
Please also refer to the instruction manual for your Bluetooth device.
1
A (Power)
Note
• You cannot connect both a Bluetooth device and Bluetooth speakers (or headphones) to
the unit at the same time.
• If you previously connected a Bluetooth device to this unit, that device will automatically
connect to the unit. If you want to connect a different Bluetooth device, first cut off the
connection with the previous Bluetooth device.
• To cut off a Bluetooth connection, tap A in the app to place the unit in standby mode, or
cut the connection from the Bluetooth device.
Listening to the music on a Bluetooth device
2
Lit
This unit
You can play back the audio (that resides on a Bluetooth device) through this
unit by connecting this unit to the Bluetooth device.
Note
If you are planning to connect a Bluetooth device to the unit for the first time, complete
steps 1 and 2 (shown on the right) within a timespan of five minutes.
On the Bluetooth device, select
this unit from the Bluetooth
device list.
3
Bluetooth device
This unit
Powered
speakers
The Bluetooth indicator will light
up when the connection is
established.
Playback
Note
If the connection fails, try steps 1 and 2 again.
10
Playback
Listening through Bluetooth-compatible
speakers or headphones
1
Set the speakers or headphones (that you want to
connect to the unit) to pairing mode.
You can listen to the audio from this unit through Bluetooth-compatible speakers
or headphones that are connected to the unit. Follow steps 1 - 7 shown on the
right.
2
Playback
NonBluetooth
music source
Via network
MusicCast
CONTROLLER
This unit
Bluetooth-compatible
speakers/headphones
3
Note
You cannot transmit audio from AirPlay (with iOS), or from one Bluetooth device to another
Bluetooth device, for listening.
Lit
7
6
4
11
5
The Bluetooth indicator
will light up when the
connection is established.
Configuring the MusicCast network
If you have multiple devices that support MusicCast (called “supported devices”
in this manual), you will be able to easily configure a home audio network using
MusicCast CONTROLLER. After registering the unit to the app, register other
supported devices to the app.
Standard Mode and Extend mode
If you make a wired connection between a supported device and the wireless
LAN router (access point), you can expand the reception range (Extend mode).
This will be useful if you want to install a supported device in a location where
reception is poor.
Note
To register the unit to the app, refer to “Connect to the network.” on page 6.
Note
If you want to play high-resolution audio sources, a wired connection is
recommended.
Standard Mode: Wireless connection to the access point
Wireless LAN router
(Access point)
Registering supported devices to
the app
Supported device
This unit
Extend mode: Wired connection to the access point
3
Done
1
(Settings)
Wireless LAN router
(Access point)
2
Follow the app
instruction to register.
12
Supported device
This unit
Other functions and information
Optional settings
You can change the following settings.
Setting menu
Initializing the network settings
Enabling/disabling the Network
Standby function*
Default
–
To modify the default setting:
While pressing and holding down the [CONNECT] button on the bottom panel, insert the AC adaptor into the AC
outlet, and then keep holding down the [CONNECT] button for another three seconds.
Three indicators on the front panel will flash simultaneously and the network settings will be initialized. Do not operate the
unit until the indicators turn off.
While pressing and holding down the [A] button on the bottom panel, insert the AC adaptor into the AC outlet,
and then keep holding down the [A] button for another three seconds.
Enabled
The power indicator will flash twice and then turn off, and the Network Standby function will be disabled. Repeating this
operation will alternate between enabling and disabling.
When the Standby function is enabled: The power indicator will flash twice, and then light up steadily.
1 While the unit is in standby mode, press and hold down the [OPTION] button on the bottom panel for five seconds.
The front indicators will flash alternately.
Enabling/disabling Wi-Fi
Enabled
2 Press and hold down the [A] button for three seconds.
The Wi-Fi indicator will flash twice, and then turn off, and the Wi-Fi function will be disabled. If you connect the unit to the
Wi-Fi network again, the Wi-Fi function will be enabled ( P. 6).
1 While the unit is in standby mode, press and hold down the [OPTION] button on the bottom panel for five seconds.
The front indicators will flash alternately.
Enabling/disabling Bluetooth
Enabled
2 Press and hold down the [CONNECT] button for three seconds.
The Bluetooth indicator will flash twice, and then turn off, and the Bluetooth function will be disabled. Repeating steps 1 and
2 will alternate between enabling and disabling.
When the Bluetooth function is enabled: The Bluetooth indicator will flash twice, and then light up steadily.
* This menu enables you to configure network operation during standby mode. If you disable this setting, the unit will stop the network operation and enter Eco Standby mode to
minimize power consumption. The following functions will be unavailable during Eco
Standby mode. To use these functions, press the [A (Power)] button on the bottom
panel to turn on the power to the unit.
• Turning on the power to the unit from MusicCast CONTROLLER
• AirPlay
• Bluetooth
With an advanced energy saving design, this product achieves a low
power consumption of not more than two watts when in Network
Standby mode.
13
Other functions and information
Updating the firmware
You can update the unit’s firmware via the Internet if the unit is connected to the
Internet. If new firmware is released, you will be notified on the MusicCast
CONTROLLER screen. Follow the instructions in the app to update the firmware.
Status indicators
The update status is displayed by the front indicators.
Status
Updating
now
Update
complete
Update
failed
Indicators
Flashing from left to right one by one
Light up steadily
When the update is successfully complete, the unit will automatically
restart.
Flashing simultaneously
Note
• Be sure to follow the instructions below during the update operation.
- Do not operate the unit.
- Do not disconnect the Power cord, AC adaptor, or LAN cable.
• A firmware update may fail due to insufficient Internet speed or other issues related to
wireless network connections. In such a case, disconnect the AC adaptor from the AC
outlet, re-connect it, and then try again to update the firmware.
14
Other functions and information
Sharing the iPhone settings and connecting to a network
When you turn on the power to the unit for the first time after purchasing the unit
2 Choose the wireless network (access point) you want to
or initializing the network settings, the Wi-Fi indicator on the front panel will flash,
access with the unit.
and the unit will automatically start searching for an iOS device, such as an
iPhone. At this time, you can connect the unit to the network easily by applying
the network settings on the iOS device to the unit.
When the sharing setup is complete, the unit will automatically connect to the
selected wireless network.
* To take full advantage of the functions on this unit, install MusicCast CONTROLLER on
your iOS device.
Tap here to start setup
Note
•
•
•
•
If you make a wired connection, this function is not available.
Make sure that the iOS device is connected to the wireless LAN router (access point).
An iOS device running iOS 7.1 or later is required.
If the wireless LAN router features WEP wireless encryption, the unit will be unable to
share the network settings on the iOS device to connect to the network.
Currently-selected network
1 While the Wi-Fi indicator is flashing, open the Wi-Fi setting
screen on the iOS device, and then assign this unit for the
AirPlay speaker.
iOS 9 (example of English version)
WXAD-10 XXXXXX
Name of the unit
15
Troubleshooting
Refer to the table below if the unit fails to function properly. If your problem is not listed below, or if the symptoms persist after you follow the instructions below, turn off
the power to the unit, disconnect the AC adaptor from the AC outlet, and contact your nearest authorized Yamaha dealer or service center.
General
Problem
The unit is not turned on.
The unit turns off as soon as it is
powered on.
The unit does not operate properly.
The unit is not operable.
Cause
Solution
The AC adaptor or Power cord is not properly connected.
Make sure that the AC adaptor and Power cord are correctly
connected, and insert the AC adaptor into the AC outlet firmly.
The internal microcomputer has frozen, due to an external
electrical shock (such as lightning or excessive static
electricity) or due to a drop in the power supply voltage.
Unplug the AC adaptor from the AC outlet, wait 30 seconds or
more, and then plug the AC adaptor back in.
The music source you want to play was not selected properly. Use the MusicCast CONTROLLER app to select the music
source you want to play ( P. 7).
No sound
There is noise interference from
nearby electronic equipment.
Unable to adjust the volume.
The speaker or audio system has not been connected
properly.
Make sure that the system is connected properly.
Cables are connected to both the [AUX OUT] and [LINE OUT]
jacks.
If you connect cables to both jacks, no audio will be output
from the [LINE OUT] jack. To output audio from the [LINE
OUT] jack, remove the cable from the [AUX OUT] jack.
The volume level of the device connected to the unit is set to
minimum or muted.
Turn up the volume.
The unit is too close to electronic equipment.
Place the unit further away from such equipment.
Noise interference may be generated if you do not use the
supplied Power cord and AC adaptor.
Be sure to use the supplied Power cord and AC adaptor.
Cable is connected to the [LINE OUT] jack.
Connect the cable to the [AUX OUT] jack.
16
Troubleshooting
MusicCast
Problem
Unable to make the connection
settings using MusicCast
CONTROLLER.
Cause
Solution
The mobile device is not connected to the wireless LAN router
(access point).
Connect the mobile device to the wireless LAN router, and
then make the connection settings using MusicCast
CONTROLLER.
The unit is turned off.
Turn on the power to the unit.
Network
Problem
Cause
Solution
The unit and the mobile device are not on the same network.
MusicCast CONTROLLER does not
detect this unit.
Check the network connections and your router settings, and
then connect the unit and mobile device to the same network.
You are using a router supporting multi SSIDs.
The router’s network split function may be blocking access to
the unit. If you are connecting an iPhone, use an SSID that
allows access to the unit. (Try to connect to the Primary SSID.)
The network feature does not
function.
The network parameters (IP address) have not been obtained
properly.
Enable the DHCP server function on the router.
The file format is not supported by the unit or the PC (or
server).
Be sure to use a file format that is supported by the unit and
the PC. For information on music files supported by this unit,
please refer to “Supported devices/media and file formats”
( P. 20).
The media sharing settings on the PC are not correct.
Modify the media sharing settings so that the unit will be able
to access the folders on the PC (or server) ( P. 8).
Security software installed on your PC (or server) is blocking
the unit from accessing the PC.
Check the settings of the security software installed on your
PC (or server).
The unit and the PC are not connected to the same network.
Check the network connections and the router settings, and
then connect the unit and PC to the same network.
Files on the PC (or server) are not
displayed (played back).
MusicCast CONTROLLER does not
detect the PC (or server).
17
Troubleshooting
Problem
Cause
Solution
The selected Internet radio station is currently out of service.
There may be a network problem at the radio station, or the
broadcasting service may have been stopped. Try to play the
station later or select another station.
The selected Internet radio station is currently broadcasting
silence.
Some Internet radio stations broadcast silence at certain
times of the day. In this case, there is no problem with the
reception, but no audio will be produced. Try the station later
or select another station.
Access to the network is restricted by the firewall settings of
the network devices (such as the router).
Check the firewall settings on your devices. The Internet radio
can be played only through the port designated by each
radio station. The port number varies depending on the radio
station.
The network connection is unstable.
Try updating again after a while.
The wireless LAN router is turned off.
Turn on the power to the wireless LAN router.
The unit and the wireless LAN router are too far apart.
Place the unit and the wireless LAN router closer to each
other.
There is an obstacle between the unit and the wireless LAN
router.
Move the unit and the wireless LAN router in a location where
there are no obstacles between them.
A device that uses a frequency band of 2.4 GHz (microwave
oven, wireless LAN device, etc.) is interfering the wireless
communication.
Turn off the power to the device, or relocate it further away
from the unit and the wireless LAN router.
Access to the network is restricted by the firewall settings of
the wireless LAN router (access point).
Check the firewall setting of the wireless LAN router.
You are using a router supporting multi SSIDs.
The router’s network split function may be blocking access to
the unit. If you are connecting an iPhone, use an SSID that
allows access to the unit. (Try to connect to the Primary SSID.)
Unable to play the Internet radio.
Firmware update failed.
The unit is unable to connect to the
Internet via a wireless LAN router
(access point).
MusicCast CONTROLLER does not
detect a wireless network.
The iPhone does not detect the unit
when using AirPlay.
18
Troubleshooting
Bluetooth
Problem
Unable to pair the unit with the
Bluetooth device.
No sound or the sound is
interrupted during playback.
Cause
Solution
Your Bluetooth device does not support A2DP.
Pair with a Bluetooth device that supports A2DP.
The passkey of the device, such as a Bluetooth adaptor, that
you want to pair with the unit is other than “0000.”
Use a connecting device with a passkey “0000.”
The unit and the Bluetooth device are too far apart.
Move the Bluetooth device closer to the unit.
A device that uses a frequency band of 2.4 GHz (microwave
oven, wireless LAN device, etc.) is interfering the wireless
communication.
Move the unit away from the device.
Another Bluetooth device is already connected to this unit.
Terminate the current Bluetooth connection, and then pair
with the new device.
The Bluetooth function on the unit is disabled.
Enable the Bluetooth function on the unit ( P. 13).
The Bluetooth connection has been cut.
Re-establish the Bluetooth connection. ( P. 6).
The unit and the Bluetooth device are too far apart.
Move the Bluetooth device closer to the unit.
A device that uses a frequency band of 2.4 GHz (microwave
oven, wireless LAN device, etc.) is interfering the wireless
communication.
Turn off the power to the device, or relocate it further away
from the unit and the Bluetooth device .
The Bluetooth device is not set to send audio signals to this
unit.
On the Bluetooth device, select this unit as the audio output
destination.
The volume level of the Bluetooth device is too low.
Increase the volume level of the Bluetooth device.
19
Supported devices/media and file formats
PC
File format
A PC with the following software installed.
• Windows Media Player 11/Windows Media Player 12
This unit supports the following formats.
File
WAV
(PCM
format only)
Sampling
frequency
(kHz)
Quantization
bitrate (bit)
Bitrate
The
number of
channels
Gapless
playback
32/44.1/48/
88.2/96/176.4/
192
16/24
–
2

–
up to
320
kbps
2
–
–
up to
320
kbps
2
–
–
up to
320
kbps
2
–
32/44.1/48
MP3
32/44.1/48
WMA
MPEG-4
AAC
32/44.1/48
FLAC
32/44.1/48/
88.2/96/176.4/
192
16/24
–
2

ALAC
32/44.1/48/
88.2/96
16/24
–
2

AIFF
32/44.1/48/
88.2/96/176.4/
192
16/24
–
2

NAS
NAS that is compatible with DLNA version 1.5.
AirPlay
Supports iOS 7 or later for setup using Wireless Accessory Configuration.
AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with
OS X Mountain Lion or later, and PC with iTunes 10.2.2 or later.
(as of March 2017)
Made for:
iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus,
iPhone 6, iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s
iPad Pro (9.7-inch and 12.9-inch), iPad mini 4, iPad Air 2, iPad mini 3, iPad Air,
iPad mini 2, iPad mini, iPad (3rd and 4th generation), iPad 2
iPod touch (5th and 6th generation)
(as of March 2017)
Bluetooth
Bluetooth is a technology for wireless communication employing the 2.4 GHz
frequency band, which can be used without a license.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a radio band
shared by many types of equipment. While Bluetooth compatible devices use
a technology minimizing the influence of other components using the same
radio band, such influence may reduce the speed or distance of
communications and in some cases interrupt communications.
• The speed of signal transfer and the distance at which communications is
possible differs according to the distance between the communicating
devices, the presence of obstacles, radio wave conditions and type of
equipment.
• Yamaha does not guarantee all wireless connections between the sound bar
and devices compatible with Bluetooth function.
• To play back FLAC files, you need to install server software that supports
sharing of FLAC files via DLNA on your PC or use a NAS that supports FLAC
files.
• Digital Rights Management (DRM) contents cannot be played back.
20
Specifications
Network
AUX OUT
Ethernet interface
100 Base-TX/10 Base-T
Internet radio
airable.radio service supported
PC client function
DLNA Ver. 1.5 (DMR function) supported
Supported file format
WAV (PCM only), MP3, WMA, MPEG-4 AAC,
FLAC, ALAC, AIFF
AirPlay
AirPlay supported
Output connector
LINE OUT
Output connector
IEEE 802. 11 b/g/n
Radio frequency
2.4 GHz
Available security method
WEP, WPA2-PSK (AES), Mixed Mode
RCA jack
POWER SUPPLY
Wi-Fi
Wireless LAN standards
3.5 mm stereo mini jack
Power voltage/frequency
AC 100-240 V
50/60 Hz
Power consumption
2.8 W
Standby
power
consumption
Network standby off /
Bluetooth standby off
Network standby on /
Bluetooth standby off
Wired
1.6 W
Wireless (Wi-Fi)
1.7 W
Network standby on /
Bluetooth standby on
Wired
1.6 W
Wireless (Wi-Fi)
1.7 W
Bluetooth
Bluetooth version
Bluetooth Ver. 2.1+EDR
Supported profile
A2DP (Advanced Audio Distribution Profile)
OTHERS
AVRCP (Audio/Video Remote Control Profile)
Compatible codec
Dimensions (W x H x D)
Sink: SBC, AAC
Sink or Source
RF output power
Bluetooth Class 2
Maximum communication
range
10 m (33 ft) (without interference)
130 x 45 x 106 mm
(5-1/8 x 1-3/4 x 4-1/8 inch)
Source: SBC
Operation mode
0.2 W
Weight
226 g (8.0 oz)
The contents of this manual apply to the latest specifications as of the publishing
date. To obtain the latest manual, access the Yamaha website then download the
manual file.
21
Trademarks
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in some sections. You
have the right to obtain, duplicate, modify, and redistribute this open-source
code only. For information on GPL/LGPL open source software, how to obtain it,
and the GPL/LGPL license, refer to the Yamaha Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under
license.
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
“Made for iPod,” “Made for iPhone,” and “Made for iPad‚” mean that an
electronic accessory has been designed to connect specifically to iPod, iPhone,
or iPad, respectively, and has been certified by the developer to meet Apple
performance standards.
Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards.
DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks of
Digital Living Network Alliance. All rights reserved. Unauthorized use is strictly
prohibited.
Please note that the use of this accessory with iPod, iPhone, or iPad may affect
wireless performance.
iTunes, AirPlay, iPad, iPhone, iPod, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Windows™
Windows is a registered trademark of Microsoft Corporation in the United States
and other countries.
iPad Air and iPad mini are trademarks of Apple Inc.
App Store is a service mark of Apple Inc.
Internet Explorer, Windows Media Audio and Windows Media Player are either
registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
Android™ Google Play™
Android and Google Play are trademarks of Google Inc.
MusicCast is a trademark or registered trademark of Yamaha Corporation.
Yamaha Eco-Label is a mark that certifies products of high
environmental performance.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
22
Yamaha Global Site
http://www.yamaha.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Group
© 2017 Yamaha Corporation
Published 03/2017 IP-A0
WXAD-10OM/EN
23
Download PDF

advertising