Direct Attach Cable T-TECH CO.,LIMITED 1/6 40G QSFP+ to 4*10G

Direct Attach Cable T-TECH CO.,LIMITED 1/6 40G QSFP+ to 4*10G
Direct Attach Cable
40G QSFP+ to 4*10G SFP+ Breakout Passive Copper Cable
Features:
Connector A: (1) QSFP 40.0 Gbps Rated Connector (SFF-8436 Compliant)
Connector B: (4) SFP+ 10.0 Gbps Rated Connectors (SFF-8431 Compliant)
Economically Links up a QSFP port with an Upstream 10GbE-SFP+ Switch
Protocol agnostic support of 40GbE, QDR InfiniBand, SAS & Fibre Channel
Up to 10.3125 Gbps transfer rate per SFP+ channel (40 Gbps aggregate)
Robust Zinc die-cast SFP+ & QSFP connectors with pull-to-release latching
Bridge the gap between your 10G and 40G capable switches/host adapters
Low cross-talk and pair-to-pair skew maintains signal integrity
Fully compliant to the latest SFP+ & QSFP MSA (Multi-Source-Agreement)
Supports all current 10-Gigabit Ethernet and 40-Gigabit Ethernet standards
Designated form factor and electrical compliance for QDR InfiniBand
The perfect direct attached storage splitter cable for Fibre Channel & SAS
Enjoy a reduced power budget and lower port cost compared to optical
Fully RoHS compliant for environmental protection
Applications:
InfiniBand SDR, DDR
Ethernet 1G, 10G
FibreChannel
Rack-to-Rack, Shelf-to-Shelf Interconnect
Networking
Storage
Hubs, switches, routers, servers
Description:
QSFP+ (Quad Small Form-factor Pluggable Plus) copper direct-attach cables are suitable for very short distances
and offer a highly cost-effective way to establish a 40-Gigabit link between QSFP+ ports of QSFP+ switches within
racks and across adjacent racks. These cables are used for 40GbE and Infniband standards, to maximize
performance. QSFP+ are designed to meet emerging data center and high performance computing application needs
for a high density cabling interconnect system capable of delivering an aggregate data bandwidth of 40Gb/s. This
interconnect system is fully compliant with existing industry standard specifications such as the QSFP MSA and IBTA
(InfiniBand Trade Association). The QSFP+ cables support the bandwidth transmission requirements as defined by
IEEE 802.3ba (40 Gb/s) and Infiniband QDR ( 4x10 Gb/s per channel) specifications.
Absolute Maximum Ratings:
T-TECH CO.,LIMITED
1/6
Direct Attach Cable
Note:
Stress or conditions exceed the above range may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions above those listed in the operational sections
of this specification is not applied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Recommended Operating Conditions:
Pin Descriptions:
T-TECH CO.,LIMITED
2/6
Direct Attach Cable
1. GND is the symbol for signal and supply (power) common for QSFP modules. All are common within the QSFP
module and all module voltages are referenced to this potential otherwise noted. Connect these directly to the host
board signal common ground plane.
2. Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power suppliers and shall be applied concurrently.
Recommended host board power supply filtering is shown below. Vcc Rx, Vcc1 and Vcc Tx may be internally
T-TECH CO.,LIMITED
3/6
Direct Attach Cable
connected within the QSFP transceiver module in any combination. The connector pins are each rated for a
maximum current of 500mA.
Recommended power supply filtering Example of QSFP Host board schematics.
A typical host board mechanical layout for attaching the QSFP transceiver is presented below. The recommended
host electrical connector should be a 38-pin IPASS right angle connector assembly and the cage assembly should be
QSFP single cage
Mechanical Dimensions:
Recommended PCB layout:
A typical host board mechanical layout for attaching the QSFP transceiver is presented below. The
recommended host electrical connector should be a 38-pin IPASS right angle connector assembly and
the cage assembly should be QSFP single cage.
T-TECH CO.,LIMITED
4/6
Direct Attach Cable
QSFP+ Host Board Schematic for active copper cables:
T-TECH CO.,LIMITED
5/6
Direct Attach Cable
Mechanical Dimensions:
Ordering information:
T-QSFP-4SFP-DAC-30-1
1 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 30AWG
T-QSFP-4SFP-DAC-30-1.5
1.5 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 30AWG
T-QSFP-4SFP-DAC-30-2
2 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 30AWG
T-QSFP-4SFP-DAC-30-3
3 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 30AWG
T-QSFP-4SFP-DAC-26-5
5 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 26AWG
T-QSFP-4SFP-DAC-24-7
7 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 24AWG
T-QSFP-4SFP-DAC-24-10
10 meter 40G QSFP+ to 4×10G SFP+ Breakout
Passive Copper Cable 24AWG
Notice:
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically
confirmed in writing by T-TECH before they become applicable to any particular order or contract. In accordance with
the T-TECH policy of continuous improvement specifications may change without notice. The publication of
information in this data sheet does not imply freedom from patent or other protective rights of T-TECH or others.
Further details are available from any T-TECH sales representative.
Contact:
E-mail:sales@t-techvip.com
http://www.t-techvip.com
T-TECH CO.,LIMITED
6/6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising