WALL - MOUnT KiT

WALL - MOUnT KiT
Wall - Mount Kit
For Standard and Tower DVR/CPU Lockboxes
Easily wall-mount your DVR and CPU Lockboxes
Mier’s NEW BW-215 Wall-Mount Kit is designed to fit
all of Mier’s standard model and tower model DVR & CPU
Lockboxes allowing easy wall-mount installation and
protection for DVRs or CPUs. Holes in the bottom of Mier’s
Lockboxes allow them to be bolted directly to the BW-215
shelf. All Hardware Included!
NEW!
BW-215 Wall-Mount Kit
The BW-215 easily fits the following DVR/CPU Lockboxes:
Standard DVR Lockboxes:
•
•
•
•
BW-200 is 20”W x 8”H x 20”D
BW-201 is 16”W x 5”H x 16”D
BW-224 is 20”W x 8”H x 24”D
BW-225 is 20”W x 5”H x 20”D
NEW Tower DVR/CPU Lockbox:
• BW-240 is 8”W x 20”H x 20”D
Shown with a Standard Model
Mier DVR Lockbox
(sold separately)
Along with the DVR/CPU lockboxes shown here,
Mier also offers Rack-Mount Lockboxes and
Outdoor Temperature Controlled Lockboxes.
Call Mier or visit the website for information on our other
product lines and services!
Shown with a Tower Model
Mier DVR/CPU Lockbox
(sold separately)
1-800-473-0213 | www.mierproducts.com
Wireless Vehicle Detection | Driveway Alarms | Drive-Up Window Detection | Buried Sensor Systems | Instrument Boxes | DVR/CPU Lockboxes
Flush-Mount Cabinets | Outdoor Enclosures | NEMA 4 Enclosures | Temperature Controlled Enclosures | Power Supply Boxes | Siren/Speaker
Cabinets | Bell Boxes | Battery Cabinets | Transformer Enclosures | Custom Fabrication | Custom Colors | Custom Screening
BW-215 Wall - Mount Kit
For Standard and Tower DVR/CPU Lockboxes
Easily wall-mount your DVR and CPU Lockboxes
BW-215 Wall-Mount Kit Installation:
1.
Determine the desired location of the shelf on a wall stud, place the U-Channel on a the wall, then mark the top mounting hole.
CAUTION: The U-Channel must be mounted on the
centerline of a wall stud OR with suitable anchors
directly to brick or cement wall.
2.
Drill a 3/16 pilot hole in the wall stud at the top
mounting hole.
3.
Use a level and carefully mount the U-Channel
vetically along the stud with one 5/16 x 2” lag screw at the top mounting hole.
4.
With the U-Channel vertical, drill another 3/16” pilot hole at the lower mounting hole and bolt to wall with another 5/16 x 2” lag screw.
Tighten both lag screws firmly.
5.
Attach the Angle Brace at the bottom of the
U-Channel with one 1/4 x 20 x 3.5” bolt, flat washer, and nut.
6.
Attach the Lockbox Shelf at the top of the U-Channel with one 1/4 x 20 x 3.5” bolt, flat washer, and nut.
7.
Attach the front of the Angle Brace to the front of the
Lockbox Shelf with one 1/4 x 20 x 3.5” bolt, flat washer and nut.
8.
Tighten all hardware before bolting lockbox to shelf.
BW-215 Wall-Mount Kit
1,2,3
Steps 1-4
4
Step 5
5
7
6
Step 6-7
1-800-473-0213 | www.mierproducts.com
Wireless Vehicle Detection | Driveway Alarms | Drive-Up Window Detection | Buried Sensor Systems | Instrument Boxes | DVR/CPU Lockboxes
Flush-Mount Cabinets | Outdoor Enclosures | NEMA 4 Enclosures | Temperature Controlled Enclosures | Power Supply Boxes | Siren/Speaker
Cabinets | Bell Boxes | Battery Cabinets | Transformer Enclosures | Custom Fabrication | Custom Colors | Custom Screening
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement