Bluetooth® pairing with legacy mode

Bluetooth® pairing with legacy mode
Bluetooth® pairing with legacy mode
If you are unable to pair your Moneris PAYDTM PIN pad in SSP mode, follow these steps carefully to enable
legacy mode on the PAYD® PIN pad and then pair the PAYD PIN pad with your mobile device via Bluetooth.
Don’t worry; you’ll only have to do this once.
Note: Ensure the PAYD PIN pad is connected to an external power source while you perform the following steps.
Confirm that the WELCOME/BONJOUR screen is displayed on the PAYD PIN pad before you proceed.
1. POWER UP YOUR MOBILE DEVICE
a) Turn on your mobile device.
b) Ensure Bluetooth is turned on, your mobile device is discoverable, and the Bluetooth menu is displayed.
c) Set your mobile device aside.
2. RE-ENABLE LEGACY MODE ON THE PAYD PIN PAD
a) On the PAYD PIN pad’s WELCOME/BONJOUR screen, simultaneously press and hold down the yellow
key and the
key.
b) Wait while the PAYD PIN pad reboots (this will take several seconds).
c) When you see the following screen, you have 10 seconds to press the red
key and then the green
key.
d) When you see the TELIUM MENU screen, select YES (F4).
Note: If you see the WELCOME/BONJOUR screen instead, go back to step 2a on this page.
e) When you see the PRESS F KEY screen, press the
f)
key.
When you see the FUNCTIONS menu, press the 2 key to select BT PAIRING.
g) Press the 6 key to select Security Mode.
h) Press the F2 key to highlight Legacy (3), then press the green
key.
i)
Wait while the PAYD PIN pad reboots back to the WELCOME/BONJOUR screen.
j)
Continue on the next page.
P. 1
3. ACCESS THE BT PAIRING FUNCTIONS ON THE PAYD PIN PAD
a) On the PAYD PIN pad’s WELCOME/BONJOUR screen, simultaneously press and hold down the yellow
key and the
key.
b) Wait while the PAYD PIN pad reboots (this will take several seconds).
c) When you see the following screen, you have 10 seconds to press the red
key and then the green
key.
d) When you see the TELIUM MENU screen, the PAYD PIN pad is ready to pair with your mobile device:
Note: If you see the WELCOME/BONJOUR screen instead, go back to step 3a on this page.

To pair the PAYD PIN pad with an iPhone®, iPad®, or iPod Touch®, go to page 3.

To pair the PAYD PIN pad with an AndroidTM mobile device, go to page 4.
P. 2
Pairing with an iPhone, iPad, or iPod Touch
Note: Leave the PAYD PIN pad connected to an external power source while you perform the following setup
steps. Ensure that the Bluetooth menu is displayed on your iPhone, iPad, or iPod Touch (collectively referred to
as “mobile device”).
1.
MAKE THE PAYD PIN PAD DISCOVER YOUR MOBILE DEVICE VIA BLUETOOTH
a) On the PAYD PIN pad's TELIUM MENU screen, select YES (F4).
b) When you see the PRESS F KEY screen, press the
key.
c) When you see the FUNCTIONS menu, press the 2 key to select BT PAIRING.
d) Press the 2 key to select Pair device (iOS).
e) When you see the AVAILABLE DEVICES screen, press the green
f)
key to select Search devices.
When you see a list of devices, scroll (F2) to your mobile device, and press the green
it.
key to select
g) When you see the Start pairing… screen with a 16-digit PIN code, go to the next step.
Note: This screen will time out after 1 minute.
2. ENTER THE BLUETOOTH PIN CODE ON YOUR MOBILE DEVICE
a) On your mobile device, enter the 16-digit PIN code when prompted.
b) On the PAYD PIN pad, you will see Pairing Success and then the BT PAIRING menu.
Note: Your mobile device will indicate the PAYD PIN pad ID is "Connected". (If your mobile device
prompts you to download or install an app, decline the prompt, and continue the setup steps below.)

If you see Pairing Failure (your mobile device will display a similar "failure" message), go back to
step 1d on this page and retry the pairing steps.
c) On the PAYD PIN pad, press the red
the WELCOME/BONJOUR screen.
key, and then wait while the PAYD PIN pad reboots back to
d) Go to Initializing the PAYD PIN pad on page 5.
P. 3
Pairing with an Android mobile device
Note: Leave the PAYD PIN pad connected to an external power source while you perform the following setup
steps. Ensure that the Bluetooth menu is displayed on your mobile device.
1. MAKE THE PAYD PIN PAD DISCOVER YOUR MOBILE DEVICE VIA BLUETOOTH
a) On the PAYD PIN pad's TELIUM MENU screen, select YES (F4).
b) When you see the PRESS F KEY screen, press the
key.
c) When you see the FUNCTIONS menu, press the 2 key to select BT PAIRING.
d) Press the 1 key to select Pair device (Android).
e) When you see the Waiting for pairing... screen with a PIN code, go to the next step (do not use this
code).
2. ENTER A BLUETOOTH PIN CODE ON YOUR MOBILE DEVICE
a) Make your mobile device actively scan for devices with which to pair.
b) When you see the 8-digit PAYD PIN pad ID (e.g., I6023456) on your mobile device, tap the PAYD PIN
pad ID.
Note: The ID always starts with "I6" and is printed on a label affixed to the back of the PAYD PIN pad.
c) When you are prompted for a PIN code, enter any 8- to 16-digit number of your choosing.
Note: You will also enter this number as the PIN code on the PAYD PIN pad in the next step.
3. ENTER THE BLUETOOTH PIN CODE ON YOUR PAYD PIN PAD
a) When you see the ENTER PIN CODE 8 to 16 digits screen on the PAYD PIN pad, enter the same
number that you entered on your mobile device in step 2c, then press the green
key.
b) On the PAYD PIN pad, you will see Pairing Success and then the BT PAIRING menu.
Note: Your mobile device will indicate the PAYD PIN pad ID is "Paired".

If you see Pairing Failure (your mobile device will display a similar "failure" message), go back to
step 1 d) on this page and retry the pairing steps.
Note: You may reuse the same PIN code or re-enter a different one.
c) On the PAYD PIN pad, press the red
WELCOME/BONJOUR screen.
key, and wait while the PAYD PIN pad reboots back to the
d) Go to Initializing the PAYD PIN pad on page 5.
P. 4
Initializing the PAYD PIN pad
Now you can initialize the PAYD PIN pad from the mobile payment app on your mobile device.
a) For instructions on how to initialize the PAYD PIN pad, refer to the “Getting Started” section of your
Welcome Email.
IMPORTANT: Make sure you fully charge the PAYD PIN pad before using it to accept payments. When the
battery icon in the top right corner of the PAYD PIN pad's WELCOME/BONJOUR screen is solid black, it means
the battery is fully charged.
Charge Amount
Battery Icon
100% (full) charge
® PAYD is a registered trade-mark of Moneris Solutions Corporation. BLUETOOTH is a registered trade-mark of Bluetooth SIG, Inc. IPHONE,
IPAD, and IPOD TOUCH are trade-marks of Apple Inc., registered in the U.S. and other countries. TM MONERIS PAYD and MONERIS PAYD
& Design are trade-marks of Moneris Solutions Corporation. ANDROID is a trade-mark of Google Inc All other marks or registered trademarks are the property of their respective owners.
Last updated: May 2015
P. 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement