Digital System. Reading this Owner’s Guide prior to using your system will help maximize the use of it and its many features. For any additional questions please contact your authorized Directed dealer or Directed at 1-800-753-0600. Additional support is also available at: http://support.directed.com

Important information

Government Regulations and Safety information

Read the Government Regulations and Warning!

Safety First sections of this manual prior to operating this system.

Warning! Failure to heed this information can result in death, personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose.

Your Warranty

Your system comes with a warranty. The warranty terms are detailed at the end of this guide. Make sure that you receive the proof of purchase from your dealer, indicating the product was installed by an authorized Directed dealer

.

Replacement remote controls

Please see your authorized dealer or visit us at www.directedstore.

com to order additional remote controls. Remote control RPN

(Remplacement Part Number) are typically found on the back of the device.

Introduction

Antenna

In-vehicle System Antenna

The in-vehicle system antenna, typically located on the upper part of the front windshield sends and receives commands or messages to and from your system.

ANTENNA

CABLE

CONTROL

MODULE

Remote Control Pairing with XL202

Once this Antenna has been installed, you must pair the remote with the system. Use the following procedure to pair the XL202 with the remote control.

Compatibilities

RF Kit Part #

9111, 9115, 9116

Included in RF Kit

(XL202 not included)

Remote

Part #

(2) 1-way

7111, 7115, 7116

Antenna

Part #

XL202

Firmware

6102T 202.RFTDKLQ0

Find the XL202 (control module) located under the the driver’s side dash, determine how you want the remote to operate and proceed with the proper programming steps.

With UNLOCK ALL option:

XL202

Press and release 1 time, then press and hold the Programming button of the

XL202 module. The LED flashes slowly.

XL202

Press & Release

Press & Hold

Flashes

Red slowly

With DRIVER DOOR PRIORITY UN-

LOCK option:

Press and hold the Programming button of the XL202 module. The LED flashes slowly.

XL202

XL202

Press & Hold

With UNLOCK ALL option and 2x start activation*:

XL202

Press and release 4 times, then press and hold the Programming button of the

XL202 module. The LED flashes slowly.

XL202

Press & Release

Press & Hold

Flashes

Red slowly

Flashes

Red slowly

With DRIVER DOOR PRIORITY UN-

XL202

Press and release 3 times, then press and hold the Programming button of the

XL202 module. The LED flashes slowly.

XL202

Press & Release

Press & Hold

Flashes

Red slowly

Press the button on the remote. The LED on the XL202 turns ON solid for one second, then turns OFF to indicate the pairing was completed successfully.

When programming of every remote is finished, release the Programming button on the XL202.

Press

XL202

Solid Red x 1 sec

Off

XL202

Release

Note: Exiting Pairing Mode

The XL202 Learn Routine exits if the programming button is released.

Remote Control Pairing with a 4X10/5X10

Find the Valet button usually located under the driver’s side dash and the status LED, then proceed with the programming steps.

Open at least one vehicle door.

Open door

Turn the ignition to the ON position.

Key OUT

START

Key IN

START

Key IN

START

Key IN

START

Within 10 seconds, press and release once and then press and hold the system’s Valet button. The status LED begins flashing in a sequence of 1 flash and the siren/horn (if connected) sounds to confirm the system is ready for pairing.

Press and release the Start button on the remote.

The vehicle horn sounds (if connected) to confirm the system has paired with the remote control. If Remote Pairing fails, repeat the above procedure or confirm the firmware flashed to the

4X10/5X10 is correct for the type Antenna/

Remote being used.

Release the Valet button and Turn the ignition OFF.

Press & Release

Key OUT

Release

& Press & Hold

Flashes

Red x1

Siren/Horn sounds

Press &

Release

Siren/Horn sounds

Key IN

START

Key IN

START

Key IN

START

Note: Exiting Pairing Mode

The 4X10/5X10 Learn Routine exits if any of the following occurs:

• The ignition is turned OFF.

• There is no activity for 60 seconds.

• The Program button is pressed too many times.

Note Because of security functions 1-button remotes are not recommended/compatible with the 5X10.

Basic Commands

System State

Engine OFF

Engine ON

Press/Release Button

Start Engine

Unlock Doors

Press/Hold for 3 sec.

Car Finder*

Stop Engine

Remote Start

Press and release the button.

Activates the remote starter. The vehicle’s parking lights or hazard lights turn ON to confirm remote start signal has been received.

The runtime on the remote starter is predetermined based on vehicle application. The remote starter will shut down when the preset runtime times out or when any shutdown zone becomes active.

Unlock (if applicable)

Press and release the button.

Unlock function will only work when the vehicle is remote started.

The vehicle responds by flashing the parking lights or hazard lights twice to confirm unlocking.

Shut Off Remote Start

Press and hold the button for 3 seconds.

The vehicle shuts down from the remote start mode. The remote starter will also shut down when the preset runtime times out or when any shutdown zone becomes active.

Car Finder*

When the remote start is OFF, press and hold the remote control button for three seconds. The horn sounds (if connected) once and the parking lights flash ten times.

Remote Start Features

Key Takeover

When you are ready to drive the vehicle:

1. Unlock the doors

2. Enter the vehicle. DO NOT step on the foot brake

3. Insert the key, turn it to the run (not start) position. Step on the foot brake. The remote start is disabled and the parking lights turn OFF.

4. Begin driving.

Note If your vehicle uses a Smart Key or PTS (Push-To-Start) system, please refer to the vehicle specific instructions included with the owner’s guide of the interface module or consult your authorized dealer.

* This option is only available when using a 4X10 and 5X10.

Safety Features

The following safety features will disable the remote start when activated or not allow the engine to start if not properly set before starting.

• Foot Brake is depressed.

• Hood is open.

• Shut down toggle switch is OFF.

• The pre-programmed runtime has elapsed.

• The remote control button is pressed and held for 3 seconds or more.

Pit Stop

This remote start can keep the engine running during short trips away from the vehicle.

Enabling Pit Stop mode

1. Park in a well ventilated area.

2. With the engine running set the transmission in the park position.

3. Press and release the remote control button, the parking lights turn ON to confirm remote start is ON.

4. Turn OFF the ignition and remove the key, the engine continues running.

5. Exit the vehicle and lock the doors, the engine runs for the programmed runtime.

Note Pit Stop mode does not work if the brake pedal is pressed. If your vehicle uses a Smart Key or PTS (Push-

To-Start) system, please refer to the vehicle specific instructions included with the owner’s guide of the interface module or consult your authorized dealer.

Optional Rear Defogger

If connected, the Defogger circuit automatically activates after remote starting the vehicle.

Note This feature is only available with 4X10/5X10 system.

Disabling the Remote Start System

When the Shutdown Switch is set to the OFF position, remote engine starting is defeated. DO this when the vehicle is being serviced or driven by someone unfamiliar with remote start system operations.

Location Of Shutdown Switch: _________________________

Rapid Resume Logic

This Directed system stores its current state to non-volatile memory.

If power is lost and then reconnected the system recalls the stored state from memory.

Battery information

The remote control is powered by either two coin cell batteries

(RPN* CR-2016) or one coin cell (RPN CR-2032) that can be purchased at most retailers. When the batteries weakens, the LED on the remote dims and operating range is reduced.

Battery Replacement

1. If present, remove the small screw on the back of the remote.

2. Use a small flat blade screwdriver and insert it into the slot located along the bottom of the remote, near the key ring.

Carefully pry open the case.

3. Gently slide out the used battery to remove it from the holding clip. Orient the new battery for the correct polarity and insert into holding clip.

4. Reposition case parts, and snap together by pressing firmly and evenly on the front and back. Reinstall screw (if applicable).

5. Test Remote functions.

Battery Disposal

Directed cares about the environment. If you need to dispose of the battery, please do so in accordance with your municipal requirements for battery disposal.

* RPN (Replcement Part Number).

Patent Information

This product is covered by one or more of the following United

States patents:

Remote Start Patents:

5,349,931; 5,872,519; 5,914,667; 5,952,933;

5,945,936; 5,990,786; 6,028,372; 6,467,448;

6,561,151; 7,191,053; 7,483,783

Vehicle Security Patents:

5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591;

5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667;

5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484

Other patents pending.

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Remote Controls

To satisfy FCC RF exposure compliance requirements, this device should be used in hand-held, hand operated configurations only.

The device and its antenna must maintain a separation distance of

20 cm or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance. This device is designed to be used in a person’s hands and its operating configurations do not support normal transmissions while it is carried in pockets or holsters next to a person’s body.

Antenna

To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance.

This device complies with the Industry Canada Radio Standards

Specification RSS 210. Its use is authorized only on a nointerference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may be received, even if this interference could affect the operation of the device.

WARNING! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

Warning! Safety First

Please read the safety warnings below before proceeding. Improper use of the product may be dangerous or illegal.

Installation

Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. If you have any questions, ask your retailer or contact Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed menu wheel. It is the user’s sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE

DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO

THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING

AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE

STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole responsibility of the user.

Interference

All radio devices are subject to interference which could affect proper performance.

Upgrades

Any upgrades to this product must be performed by an authorized

Directed dealer. Do not attempt to perform any unauthorized modifications to this product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant.

Please take care to keep this product dry and away from heat sources. Any damage from water or heat will void the warranty.

Limited One Year Consumer Warranty

For a period of ONE YEAR from the date of purchase of a Directed

Electronics remote start or security product, Directed Electronics.

(“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED

ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS

WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY,

FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF

NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY

EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES

ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION

OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED

HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY

AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS.

DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE

AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE,

ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY

LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY

FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM

OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER

VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.

CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL

APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY

UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED

TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF

THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY

DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY

CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR

THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS

OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING

THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY

TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED

ABOVE.

This warranty only covers Parts sold within the United States of America and

Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com

The company behind this system is Directed

Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security and accessories available.

The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology.

Quality Directed products are sold and serviced throughout North

America and around the world.

Call (800)274-0200 for more information about our products and ser vic es.

Directed is committed to delivering world class quality products and services that excite and delight our customers.

Vista, CA 92081 www.directed.com

GRFASK1 2016-10

Hello! I am an AI chatbot specifically trained to assist you with the Clifford 9116P User's Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

Table of Contents

Congratulations

Important information

Government Regulations and Safety information

Your Warranty

.

Replacement remote controls

Introduction

Antenna

Remote Control Pairing with XL202

Compatibilities

Remote Control Pairing with a 4X10/5X10

Basic Commands

Remote Start

Unlock (if applicable)

Shut Off Remote Start

Car Finder*

Remote Start Features

Key Takeover

Safety Features

Pit Stop

Optional Rear Defogger

Disabling the Remote Start System

Rapid Resume Logic

Battery information

Battery Replacement

Battery Disposal

Patent Information

Government Regulations

Remote Controls

Antenna

Warning! Safety First

Installation

Remote Start Capable

Interference

Upgrades

Water/Heat Resistance

Limited One Year Consumer Warranty

Related

Clifford Matrix 9856X User's Guide

Directed 9856P User manual

Python 9146P User's Guide | Car Alarm System Manual

Clifford 9756P User's Guide

Directed 9816V Owner's Guide

DBALL2 VW06 Remote Start Installation Guide

FORD12 Remote Start Ready Installation Guide

Directed Directechs DB3 Installation Manual

Xpresskit DBALL, DBALL2 Installation Manual

Remote Start Module TL1 DBALL2 Installation Guide

remote start DBALL2 CHRYSLER3 Remote Start Ready Installation Guide

Directed DBALL 2 Installation Guide