CA62 User`s Manual - Operation with LED62 Keypad and PR62

CA62 User`s Manual - Operation with LED62 Keypad and PR62
English
CA62 User’s Manual Operation with LED62 Keypad and
PR62 Proximity Cards Reader
Contents
LED62 General Description 4
General Description
LED Indication
Keypad Sounder
Buttons
4
5
7
7
LED62 Keypad Operations ARMING of Partition А
“Full ARM” Mode of Partition A
“Stay ARM” Mode of Partition A
“Instant ARM” Mode of Partition A ARMING of Partition В ARMING Both Partition А and Partition В
DISARMING of Partition А, Partition В or Both Partitions Stopping the alarm
Panic Buttons
Ambush Code
Technical troubles review
User Programming Menu
12
12
12
12
13
14
Changing user rights for remote access
Enabling / Disabling the Engineer Code Access Sending of “Comm. Manual test” message
UDL Access Block
Changing of User Codes
Changing of User Rights
Changing of Manager Codes
Changing of Manager Rights
Memory LOG review from Manager
Chime Enabling / Disabling from Manager
Zone Bypassing from Manager
Setting the Clock
Setting the Date
Adding a Proximity Card
Deleting a Proximity Card
14
15
15
15
16
16
16
17
17
18
18
18
18
18
18
PR62 Proximity Card Reader Description
2
8
8
8
9
10
10
10
11
11
11
11
Changing own user code
Memory LOG review from User
Chime Enabling / Disabling from User
Zone Bypassing from User
Manager Programming Menu
8
19
General Description
LED Indication
Sound Signalization
ARMING with a Proximity card
DISARMING with a Proximity card
19
19
19
19
19
System Checklist
20
SUPPLEMENTS
21
CA62 Control Panel - User’s Manual
General Information
Guarantee
During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is
returned to the factory. All parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or for
ninety (90) days, whichever period is longer. The original purchaser shall immediately send manufacturer a written notice of
the defective parts or workmanship, which written notice must in all cases be received prior to expiry of the guarantee.
International Guarantee
Foreign customers shall enjoy the same guarantee rights as those enjoyed by any customer in Bulgaria, except that manufacturer shall not be liable for any related customs duties, taxes or VAT, which may be payable.
Guarantee Procedure
This guarantee will be granted when the appliance in question is returned. The manufacturer shall accept no product
whatsoever, of which no prior notice has been received.
Conditions for waiving the guarantee
This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its
normal use. It shall not cover:
• Damages resulting from transportation and handling;
• Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning;
• Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer;
• Damages caused by unauthorized system incorporation, changes, modifications or surrounding objects:
• Damages caused by peripheral appliances (unless such peripheral appliances have been supplied by the manufacturer:
• Defects caused by inappropriate surrounding of installed products;
• Damages caused by failure to use the product for its normal purpose;
• Damages caused by improper maintenance;
• Damages resulting from any other cause, bad maintenance or product misuse.
In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the manufacturer’s liability shall be limited to the replacement of the product as the sole compensation for breach of the guarantee.
Under no circumstances shall the manufacturer be liable for any special, accidental or consequential damages, on the
grounds of breach of guarantee, breach of agreement, negligence, or any other legal notion.
Waiver
This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or
implicit (including any implicit guarantees on behalf of the dealer, or adaptability to specific purposes), and over any other
responsibilities or liabilities on behalf of the manufacturer. The manufacturer does neither agree, nor empower, any person,
acting on his own behalf, to modify or alter this Guarantee, nor to replace it with another guarantee, or another liability with
regard to this product.
Unwarranted Services
The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion under the conditions below. The manufacturer shall accept no products for which no prior notice has been received.
• The products, which the manufacturer deems repairable, will be repaired and returned.
• The manufacturer has prepared a price list and those products, which can be repaired, shall be paid for every
repaired appliance.
• The closest equivalent product, available at the time, shall replace the products manufacturer deems irreparable.
The current market price shall be charged for every replaced product.
Warnings
Before using the LED62 Keypad, please ensure that you have read and understood the following instructions. Always
ensure that the LED62 Keypad is operated correctly.
Do not attempt to disassemble or alter any part of the equipment that is not expressly described in this guide. Internal
inspections, alterations and repairs should be conducted by qualified service personnel only.
Do not use substances containing alcohol, benzene, thinners or other flammable substances to clean or maintain the
equipment. The use of these substances may lead to fire.
Do not allow liquids to enter the interior. The equipment is not waterproof.
Disclaimer
The manufacturer reserves the right to change the specifications of the equipment described in this manual without notice.
This document contains information proprietary to the manufacturer. No part of this publication may be reproduced, photocopied, stored on a retrieval system or transmitted, without prior written permission of the manufacturer.
While every effort has been made to ensure that the information in this manual is accurate and complete, no liability can
be accepted for any errors or omissions.
ATTENTION
This manual contains information on limitations regarding product use and function, as well
as information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read!
CA62 Control Panel - User’s Manual
3
LED62 General Description
General Description
The LED62 is a keyboard designed for programming and controlling of CA62, CA60plus* and СА40*
control panels. The keyboard provides system status information to the user.
The control panel can be fully programmed from the LED62. A LED indication of the keyboard visualizes the current system status and alarm events information.
A sound buzzer informs the user about correct and incorrect button entries as well as activated
alert.
* Note: The functionality of LED62 keyboard is partially limited when connected to CA60plus or
СА40 control panels - only Partition A and zones from to 6 are available for the user.
LED Display:
2 Partitions,
12 zones,
Trouble indication
Specialized buttons for
Partitions controlling
Buttons for data
entering
(codes, parameters)
Quick buttons for sending
of alarm messages for:
“PANIC ALARM”
“MEDICAL ALARM”
Protective cover
(open)
“FIRE ALARM”
LED62 Keyboard - Front view (open protective cover)
4
CA62 Control Panel - User’s Manual
LED Indication
LED62 keyboard provides LED indications, which can be divided into three groups:
 For the Partitions status and the ARMING Mode;
 For the status of the control panel;
 For the status of the zones.
 LED Indication for the Partitions status and the ARMING Mode
Describes the status of Partition А and В in the system, and also the type of ARMING Mode - “Full
ARM” (see page 8), “Stay ARM” (see page 8) and “Instant ARM” (see page 9).
The two Partitions in the system are indicated with a “house” symbol with a capital letter (Partition А
with
and Partition В with
). The type of the ARMING mode is indicated with a “man” symbol,
respectively for Partition А on the left side (
Symbol
Indication
) and for Partition В - on the right side (
).
Description
OFF
Partition А / Partition В is not ready for ARMING - there are
activated detectors in the system, open zones; or the respective group is not available in the system.
ON (green)
Partition А / Partition В is ready for ARMING - there are no
activated detectors or open zones.
ON (red)
Partition А / Partition В is ARMED, regardless of the ARMING
Mode.
Blinking (red)
Exit time for leaving the premises in Partition А / Partition В
is running.
OFF
Partition А / Partition В is DISARMED, or is under “Full ARM”
Mode.
ON (green)
Partition А / Partition В is under “Stay ARM” Mode.
ON (red)
Partition А / Partition В is under “Instant ARM” Mode.
Example:
“Partition А” symbol lights in green, symbol “man” lights off, means that the Partition А is
DISARMED and is ready for ARMING.
“Partition В” symbol lights in red, symbol “man” lights in green, means that Partition В is under “Stay ARM” Mode. The LEDs for zones 9 and 10 are blinking slowly, means that these zones
are bypassed and there are still people staying in some premises of Partition B.
ATTENTION: Only СА62 control panel can support working with both Partitions A and B at
the same time!
CA62 Control Panel - User’s Manual
5
 Indication for the status of the control panel
The status of the control panel is visualized with the following LED indication:
Symbol
“Lightning”
(green)
Indication
Power supply 220 VAC.
OFF
No power supply 220 VAC.
Blinking
“Wrench”
(red)
Fast
Programming mode*.
ON
Technical trouble review mode.
OFF
No technical troubles in the system, including
TAMPER from zones.
Blinking
“Page”
(yellow)
Description
ON
Slowly
Fast
Technical trouble in the system - see page 11.
Programming mode*.
ON
Memory LOG - see pages 12 and 17.
OFF
No memory LOG events.
Blinking
Fast
Programming mode*.
 Indication for the status of the zones
The status of the zones is visualized with the following LED indication:
Zones**
(red)
Indication
Description
ON
Technical trouble in the respective zone - the zone
number light on in red - see page 12.
OFF
No activated detectors in the zone, or this zone is not
available in the system.
Slowly
The respective zone is Bypassed - the number of the
bypassed zone is blinking slowly - see pages 13, 18.
Fast
Opening (activating) of a zone - the number of the
opened zone is blinking fast.
Blinking
Buttons backlight
The LED62 keyboard is equipped with green backlight of the buttons. The backlight is activated
easily with pressing of a random button, opening of “Entry-Exit” or “Follow” type zones.
* Programming mode - symbols “Lightning”, “Wrench” and “Page” are blinking together.
** Indication and working with all 12 zones is supported only from СА62 control panel. With CA60plus and СА40 control panels only zones from 1 to 6 are available.
6
CA62 Control Panel - User’s Manual
Keypad Sounder
There are seven different sound combinations that indicate seven different conditions:
Signalization
Description
Button
Single short beep indicating the pressing of a key.
Confirmation
Two long sound signals, indicating the system confirmation to executed
operation.
Rejection
A single long beep, indicating system incorrectly executed operation.
Entry time
Continuous beep, indicating intrusion into an entrance zone.
Exit time
Short beeps, indicating the system is armed and the user is required to leave
the entrance zone. Ten seconds before the exit time is over beep frequency
increases.
Technical
trouble
Two short beeps at every 20 sec, indicating a technical trouble.
→
To stop the signalization press sequentially the buttons
Chime
Short beeps with subsequently increasing period, indicating intrusion into a
zone with an activated chime option.
.
Buttons
Button
Function
ARM Button. ARMING of Partition А, Partition В or both of them - this functionality of
the button is programmed from the installer.
Review of the Memory LOG or Technical troubles in the system.
ARMING of Partition А - this functionality of the button is programmed from the installer.
Review of the Memory LOG or Technical troubles in the system.
ARMING of Partition B - this functionality of the button is programmed from the installer.
Confirmation of the entered data (ENTER Button).
Single press for viewing the technical troubles in the system.
Rejection of the entered data. Cancelling the current operation (CANCEL Button).
Entering into Manager or User Programming Menu.
Sending of alarm message for “FIRE ALARM”.
Sending of alarm message for “MEDICAL ALARM”.
Sending of alarm messages for “PANIC ALARM”.
Used to enter different digital data, for example personal user or manager access
codes, settings, menu addresses, etc.
CA62 Control Panel - User’s Manual
7
LED62 Keypad Operation
Arming of Partition А
The system can be ARMED, when the symbols for “Partition А” and/ or “Partition В” light on in
green.
Note: The ARMING sequence depends on the model of the control panel and the programmed
parameters in the Engineer Menu! Ask your installer which of the described bellow ARMING
variants you have to use!
ATTENTION: Only СА62 control panel can support working with both Partitions A and B at
the same time!
“Full ARM” Mode of Partition A
Full arming means all zones are secured. Anyone going into the entrance zone is required to enter
a valid code*. Otherwise the alarm is started after the entry time is up.
ARMING variant 1 for “Full ARMING” of Partition A
(with choosing the type of the ARMING Mode - default setting):
exit
time
code*
ARMING variant 2 for “Full ARMING” of Partition A
(without choosing the type of the ARMING Mode - programmed from the installer):
exit
time
code*
ARMING variant 3 for “Full ARMING” of Partition A
(quick ARMING without user code, but with choosing the ARMING Mode type - default setting):
exit
time
ARMING variant 4 for “Full ARMING” of Partition A
(quick ARMING without user code and ARMING Mode type - programmed from the installer):
exit
time
At the end of the “Full ARM” procedure, regardless of the used arming variant, the
symbol “Partition A” lights on in red, and the symbol “man” is off.
“Stay ARM” Mode of Partition A
Stay arm means the user is allowed to remain in certain zones after the system is armed but the
entrance zone is secured. Anyone going into the entrance zone is required to enter a valid code*.
Otherwise the alarm is started after the entry time is up.
Note: Certain users may not be permitted to ARM the system in “Stay ARM” Mode.
* To the user code are assigned rights to operate with Partition A, otherwise the system will reject
the operation.
8
CA62 Control Panel - User’s Manual
ARMING variant 1 for “Stay ARMING” of Partition A
(with choosing the type of the ARMING Mode - default setting):
exit
time
code*
ARMING variant 2 for “Stay ARMING” of Partition A
(without choosing the type of the ARMING Mode - programmed from the installer):
exit
time
code*
ARMING variant 3 for “Stay ARMING” of Partition A
(quick ARMING without user code, but with choosing the ARMING Mode type - default setting):
exit
time
ARMING variant 4 for “Stay ARMING” of Partition A
(quick ARMING without user code and ARMING Mode type - programmed from the installer):
exit
time
At the end of the “Stay ARM” procedure, regardless of the used arming variant, the
symbol “Partition A” lights on in red, and the symbol “man” lights on in green. The
LEDs of the bypassed zones, which are not armed blinking slowly.
“Instant ARM” Mode of Partition A
Instant arm means the user is allowed to remain in certain zones after the system is armed but the
entrance zone is secured. Any intrusion into the entrance zone immediately starts the alarm.
ARMING variant 1 for “Instant ARMING” of Partition A
(with choosing the type of the ARMING Mode - default setting):
code*
ARMING variant 2 for “Instant ARMING” of Partition A
(without choosing the type of the ARMING Mode - programmed from the installer):
code*
ARMING variant 3 for “Instant ARMING” of Partition A
(quick ARMING without user code, but with choosing the ARMING Mode type - default setting):
ARMING variant 4 for “Instant ARMING” of Partition A
(quick ARMING without user code and ARMING Mode type - programmed from the installer):
* Note: To the user code are assigned rights to operate with Partition A, otherwise the system will
reject the operation.
CA62 Control Panel - User’s Manual
9
At the end of the “Instant ARM” procedure, regardless of the used arming variant,
the symbols “Partition A” and “man” light on in red. The LEDs of the bypassed
zones, which are not armed blinking slowly.
Arming of Partition В
ARMING of the Partition В in the system is done in the same way, as shown above for the Partition
A, but the user presses the
button. The user must have a valid code for Partition B.
When the system is used to protect two independent sites, it is possible also to arm Partition A in
one ARMING Mode and Partition B in another.
Arming Both Partition А and В
For ARMING both Partitions A and B together, the user can use the
function is programmed from the Installer.
(ARM) button, when this
Note: With the ARM Button the user can arm the system only in “Full ARM” Mode. The user must
have a valid code with rights to operate in both Partition A and B.
ARMING Both Partition A and B in “Full ARM” Mode (programmed from the installer):
exit
time
code
DISARMING of Partition А, Partition В or Both Partitions
Going into the entrance zone the user must introduce his personal code. A continuous sound signal
indicates intrusion in the entry zone and entry time starts running.
Note: Certain users may not be permitted to disarm the system.
Disarming of Partition А
entry
time
code
Note: To the user code are assigned rights to operate with Partition A, otherwise the system will reject
the operation!
Disarming of Partition В
entry
time
code
Note: To the user code are assigned rights to operate with Partition B, otherwise the system will reject
the operation!
Disarming Both Partitions A and B
entry
time
code
10
Note: To the user code are assigned rights to operate with both Partitions A and B, otherwise the
system will DISARM only that Partition for which
the User code are assigned rights!
CA62 Control Panel - User’s Manual
Stopping the Alarm
The alarm is stopped by entering a valid personal code with assigned rights to operate with both
Partitions in the system.
ATTENTION: If you cannot stop the alarm using a valid user with assigned rights to operate
with both Partitions, call the Engineer and your system technical support!
Panic Buttons
Using the panic buttons the user can send alarm signals to the control panel without sounding the
siren. To send an alarm signal:
• Press and hold for 3 to 5 seconds the
• Press and hold for 3 to 5 seconds the
• Press and hold for 3 to 5 seconds the
button to send a FIRE alarm signal.
button to send a MEDICAL alarm signal.
button to send a PANIC alarm signal.
Ambush Code
The ambush code is a personal code that disarms the system but still sends an alarm signal to the
station to indicate that the user has been forcefully made to disarm the system.
The ambush code is produced from a personal code by increasing the last digit by one. If the last
digit is 9, it is replaced by 0.
Example: Personal code: 4615 → Ambush code: 4616
Personal code: 4619 → Ambush code: 4610
Technical troubles review
The technical troubles in the system are indicated with slowly blinking symbol “wrench”
.
To review the technical troubles in a system with СА62 control panel the user has just to press the
button. The symbol lights up steady and a lighting zone number shows the type of the technical trouble - see the table bellow. The system will automatically exit the technical trouble review
mode after 30 seconds. The technical trouble sound signalization will stop, but the symbol “wrench”
will proceed blinking until the technical trouble is eliminated.
To review the technical troubles in a system with СА40 or СА60plus control panels the user has to
enter a valid code first:
code
Every lighting up digit on the display indicates one technical trouble:
LED
Technical trouble
1
No 220 V power supply
2
Battery charge level is low
3
Fuse burned
4
No telephone line
5
No communication available
6
Active TAMPER within the system
CA62 Control Panel - User’s Manual
11
User’S Programming Menu
General rules for entering and programming parameters in the USER’S Menu
Step 1: Enter a valid user code → 4 or 6 digits
Step 2: Single press the PRG button →
Step 3: Enter an address number → (1 digit - see the table in the Supplement A, page 25)
Step 4: Change the parameter value
Step 5: Confirm the change with →
button / or reject it with →
Exit from the USER Programming Menu → press several times
button
button
The blinking symbols “Lightning”, “Wrench” and “Page” show that the system is in programming
mode.
Note: Certain users may not be permitted to program the system.
Changing Own User Code
The user is required to enter his current personal code before changing it.
Sequence of operations for changing user code:
new code
new code
code
4 or 6
digits
2
beeps
repeat the
new code
Memory LOG Review from User
To review the memory LOG file the user has to enter a valid code:
code
- previous event,
- following event
Press the
button to see more information on a zone number or a user code. Information on
the events, as well as the zone numbers and the users, is presented in binary-hexadecimal form.
Use the table in the Supplement B, on page 26, to interpret them.
12
CA62 Control Panel - User’s Manual
Chime Enabling / Disabling from User
To enter into chime enable / disable programming mode the user is required to enter a valid code.
Chime enable / disable button sequence:
code
Pressing any numeric button alternatively changes the state of the chime from enabled (the zone
LEDs 1-6 light on) to disabled (the zone LEDs 1-6 light off) and vice versa. The selected state is
button.
confirmed by pressing the
By default the chime is disabled - LEDs for zones 1 - 6 light off.
Chime enabled/disabled state button sequence:
the chime
is enabled
the chime
is disabled
confirm the
setting
Zone Bypassing from User
To execute a bypass operation the user is required to enter a valid code:
code
Pressing a numeric button bypasses the respective zone. The display LED, corresponding to the
zone number, lights up permanently. Pressing the same button once again de-bypasses the zone
and the LED goes out. The selected programming is confirmed by pressing the
button.
ATTENTION: To bypass zones 10, 11 and 12 you have to use special button combinations.
• To bypass Zone 10 use button combination
+
• To bypass Zone 11 use button combination
+
.
• To bypass Zone 12 use button combination
+
.
.
Note: Certain users may not be permitted to bypass zones in the system.
Bypassing zone button sequence (zone 2 in the example):
zone 2 is
bypassed
zone 2 is not
bypassed
confirm the
setting
All bypassed zones will be restored (de-bypassed) with the next DISARMING of the system.
CA62 Control Panel - User’s Manual
13
MANAGER’S Programming Menu
General rules for entering and programming parameters in the MANAGER’S Menu
Step 1: Enter a valid manager code* → 4 or 6 digits
Step 2: Single press the PRG button →
Step 3: Enter an address number → (3 digits - see the table in the Supplement A, page 21)
Step 4: Change the parameter value
Step 5: Confirm the change with →
button / or reject it with →
Exit from the MANAGER Programming Menu → press several times
button
button
* Note: Up to 4 manager codes can be programmed to CA62 control panel.
The blinking symbols “Lightning”, “Wrench” and “Page” show that the system is in programming
mode.
Changing User Rights for Remote Access
To change the user rights for remote access, the manager is required to enter his personal code
first:
code
2 beeps
The display indicates the respective operations the user is allowed to execute. The lit numbers
indicate the permitted operations.
The rights for the user remote access, which the Manager can program are:
LED
Remote access rights
1
Remote DISARM
2
Remote ARM**
3
Remote Code Access
4
Remote Programming**
5
Remote LOG Review**
6
Remote Bypass
** Default settings for remote access rights.
Pressing a numeric button alternatively switches over the state of the respective remote access
right from disabled to enabled.
The selected programming is confirmed by pressing the
button.
User remote access rights programming button sequence:
disabling the Remote ARM
parameter
default settings
for remote access
14
confirm the
setting
CA62 Control Panel - User’s Manual
Enabling / Disabling the Engineer Code Access
To enable / disable the Engineer code right to access the Engineer programming menu, the Manager is required to enter a valid code first:
code
2 beeps
Pressing any numeric button alternatively changes the state of the parameter from enabled (the
zone LEDs 1-6 light on) to disabled (the zone LEDs 1-6 light off) and vice versa. The selected state
button.
is confirmed by pressing the
By default the Engineer is allowed to enter the Engineer Menu - LEDs for zones 1 - 6 light on.
Engineer access enabled/disabled state button sequence:
disables the
Engineer access
confirm the
setting
enables the
Engineer access
Sending of “Comm. Manual test” message
At this address the Manager of the system can send a “Communication Manual Test” message to a
central monitoring station or test message with the voice dialer VD60 (just in case there is integrated
voice dialer VD60 to the CA62 control panel). The application of this function is to test the communication part in the system from the manager, without need of sending the Engineer to the site.
To send a “Comm. Manual Test” message, the manager is required to enter his personal code
first:
2 beeps
code
The communicator will start transmitting test messages through the digital communicator to the
central station first (if there are entered telephone numbers) and then through VD60 (if it is available
in the system and there are entered telephone numbers).
button.
The Manager can exit the menu by pressing the
UDL Access Block
At this address the Manager enters a permissible number of valid access codes for UDL (ARM /
DISARM / BYPASS / PC ID) for a 24 hour period.
Enter a number from 00 up to 99, as the default settings is 10 attempts.
With reaching the permissible number of valid access codes, the system will be blocked - there
would be no UDL communication. The UDL communication will be restored at 00:00h system time.
To enter a permissible number of codes, the manager is required to enter his personal code first:
code
2 beeps
CA62 Control Panel - User’s Manual
digit
00 - 99
15
Changing of User Codes
To change a user code the Manager is required to enter his personnel code first.
User code change button sequence:
code
User No 01 - 20
2 beeps
LEDs 3, 4, 5 and 6 light up to indicate the number of code digits left to be entered.
Note: If 6-digit codes are used in the system, then LEDs 1, 2, 3, 4, 5 and 6 light up.
The manager is expected to enter the new user code.
Button sequence for entering new user code:
new code
new code
4 or 6
digits
2 beeps
repeat
If the new code is repeated
correctly the system will confirm it with a sound signal.
Changing of User Rights
To change the User rights the Manager is required to enter his personnel code first.
User rights change button sequence:
code
User No 01 - 20
2 beeps
The display indicates the respective operations the user is allowed to execute. The lit numbers
indicate the permitted operations:
LED
User’s rights
1
DISARM*
2
Stay ARM*
3
Bypass*
4
Programming*
5
Working with PARTITION A*
6
Working with PARTITION B
Pressing a numeric button alternatively switches
over the state of the respective user’s right from
disabled to enabled. The selected programming is
confirmed by pressing the
button.
* Default settings for User’s rights.
Note: Disabling all user rights will automatically
erase the programmed code combination!
User rights programming button sequence:
disabling the user programming
in the system
default
settings
confirm the
setting
Changing of Manager Codes
Up to 4 different manager codes can be programmed in the СА62 control panel, i.e. there can be up
to 4 Managers in the system - 1 Chief Manager and 3 sub-managers.
16
CA62 Control Panel - User’s Manual
The changing of the different Manager codes can be done at different addresses in the system:
- Changing the Chief Manager code (see SUPPLEMENT А - ADDRESS 210)
- Changing the Manager code No1 (see SUPPLEMENT А - ADDRESS 220)
- Changing the Manager code No2 (see SUPPLEMENT А - ADDRESS 230)
- Changing the Manager code No3 (see SUPPLEMENT А - ADDRESS 240)
To change his code the manager is required to enter his current manager code before changing it.
Manager code change button sequence:
code
Manager
ADDRESS 2х
2 beeps
LEDs 3, 4, 5 and 6 light up to indicate the number of code digits left to be entered.
Note: If 6-digit codes are used in the system, then LEDs 1, 2, 3, 4, 5 and 6 light up.
The manager is expected to enter his new code.
Button sequence for entering new manager code:
new
code
4 or 6
digits
2 beeps
repeat
new code
If the new code is repeated correctly the system will confirm it with a sound signal and the
system will exit automatically from the Manager
programming menu.
Changing of Manager Rights
To change his rights the manager is required to enter his current manager code.
Manager rights change button sequence:
code
Manager
2 beeps
ADDRESS 2х
Pressing a numeric button alternatively switches over the state of the respective manager’s right
from disabled to enabled. The display indicates the respective operations the manager is allowed to
execute. The lit numbers indicate the permitted operations:
LED
Manager rights
5
Working with PARTITION A*
6
Working with PARTITION B*
* Default settings for Chief Manager in the system.
For sub-managers No 1, 2 and 3 there are no programmed rights by default.
Note: Disabling all manager rights will automatically erase the programmed code combination!
The selected programming is confirmed by pressing the
button.
Memory LOG review from Manager
To review the memory LOG of events the manager is required to enter his code:
code
- previous event,
- following event
Press the
button to see more information on a zone number or a user code. To go back to
button again. Use the table in the Supplement B, on page
the memory LOG list press the
26, to interpret them.
CA62 Control Panel - User’s Manual
17
Chime Enabling / Disabling from Manager
To enter in the enable / disable chime mode, the manager is required to enter his code.
Chime enable/disable button sequence:
code
2 beeps
Pressing a numeric button alternatively switches over the state of the chime from disabled to enabutton.
bled. The selected programming is confirmed by pressing the
By default the chime is disabled - LEDs for zones 1 - 6 light off. See also the example for chime
enable / disable from User - page 12.
Zone Bypassing from Manager
To execute a bypass operation the manager is required to enter a valid code:
code
2 beeps
Pressing a numeric button bypasses the respective zone. The display LED, corresponding to the
zone number, lights up permanently. Pressing the same button once again de-bypasses the zone
and the LED goes out. The selected programming is confirmed by pressing the
button.
See also the example for zone bypassing from User - page 13.
Setting the Clock
To set the clock the manager is required to enter his personal code. The set entries are visualized
in binary-hexadecimal form.
Button sequence for setting the clock:
New time
code
2 beeps
(HH:MM)
Setting the Date
To set the date the manager is required to enter his personal code. The set entries are visualized
in binary-hexadecimal form.
Button sequence for setting the date:
New date
code
2 beeps
(DD:MM)
Adding a Proximity Card
To use proximity cards the system has to be equipped with a proximity card reader.
Button sequence for adding a proximity card:
code
User No 01-20 or
Manager ADDRESS 2х
2 beeps
Deleting a Proximity Card
Button sequence for deleting a proximity card:
code
User / Manager No
18
2 beeps
CA62 Control Panel - User’s Manual
PR62 Proximity Card Reader Description
General Description
The PR62 Proximity Card Reader is designed to provide control of the CA62 control
panel.
A reader LED indication visualizes the information about the reaction of the system
to the proximity card commands.
A sound buzzer informs the user about correct and incorrect card operation.
LED Indication
The PR62 Proximity Card Reader is equipped with a bicolor LED located on the front cover. The information the LED provides is:
Color
green
red
Lights up
Blinks
Command confirmed
Activation warning
Command rejected
Technical trouble
yellow
-
Ready to ARM
Sound Signalization
The proximity card reader emits six different sound combinations that indicate the six different
states of the system:
Signalization
Description
Confirmation
Two long sound signals, indicating the system confirmation to executed
operation.
Rejection
A single long beep, indicating system incorrectly executed operation.
Activation warning
Short beeps preceding the execution of an ARMING command.
Entry time
Continuous beep, indicating intrusion into an entrance zone.
Exit time
Short beeps, indicating the system is armed and the user is required to
leave the entrance zone. Ten seconds before the exit time is over beep
frequency increases.
Technical trouble
Two short beeps, indicating a technical problem.
ARMING with a Proximity card
The system must be equipped with a PR62 Proximity Card Reader for ARMING with a proximity
card. Using a proximity card the user can ARM the system only in “Full ARM” mode.
To ARM the system place the proximity card and held it in front of the reader for 4 - 5 seconds. The
indication of the reader must be monitored - warning signal for activation.
Where the card is successfully identified the reader emits an interrupted beep counting down exit
time for the armed premises.
DISARMING with a Proximity card
The system must be equipped with a PR62 Proximity Card Reader for DISARMING with a proximity
card. To DISARM the system, the proximity card must be placed and held in front of the reader, until
a confirmation beep is emitted and the reader LED lights in green.
CA62 Control Panel - User’s Manual
19
System Checklist - Fill in from the Installer
Zones Description
Zone Type:
1
Room:
Zone Type:
7
Room:
Zone Type:
2
Room:
Zone Type:
8
Room:
Zone Type:
3
Room:
Zone Type:
9
Room:
Zone Type:
4
Room:
Zone Type:
10
Room:
Zone Type:
5
Room:
Zone Type:
11
Room:
Zone Type:
6
Room:
Zone Type:
12
Room:
PGM Outputs Description
PGM1
PGM3
PGM2
SIREN
System Timers
Exit time (sec.)
Entry time (sec.)
Siren will be activated for (min.)
Installer:.........................................................................................................................
Service:..........................................................................................................................
Tel./Fax:..........................................................................................................................
NOTES:
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
........................................................................................................................................
20
CA62 Control Panel - User’s Manual
CA62 Control Panel - User’s Manual
21
Deleting a proxi card
User code 2 (- - - -)
User code 2 Attributes
Adding a proxi card
Deleting a proxi card
User code 3 (- - - -)
User code 3 Attributes
Adding a proxi card
Deleting a proxi card
User code 4 (- - - -)
User code 4 Attributes
Adding a proxi card
Deleting a proxi card
User code 5 (- - - -)
013
020
021
022
023
030
031
032
033
040
041
042
043
050
Deleting a proxi card
Adding a proxi card
012
053
User code 1 Attributes
011
User code 5 Attributes
User code 1 (- - - -)
010
Adding a proxi card
UDL access block
009
051
Comm. manual test
002
052
Engineer access code
001
Manager Menu
Remote access
000
Address
LED 2
ARMING
LED 3
Code Access
LED 4
LED 6
Bypass
LED 5
View LOG
ENABLED - LEDs on
Programming
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
DISARM
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
Enter a number from 00 to 99. Default setting - 10 attempts.
Sending of test messages to central monitoring station or test message with the voice dialer VD60.
DISABLED - LEDs off
DISARMING
LED 1
SUPPLEMENT A - Manager Programming Menu
22
CA62 Control Panel - User’s Manual
User code 6 Attributes
Adding a proxi card
Deleting a proxi card
User code 7 (- - - -)
User code 7 Attributes
Adding a proxi card
Deleting a proxi card
User code 8 (- - - -)
User code 8 Attributes
Adding a proxi card
Deleting a proxi card
User code 9 (- - - -)
User code 9 Attributes
Adding a proxi card
Deleting a proxi card
User code 10 (- - - -)
User code 10 Attributes
Adding a proxi card
Deleting a proxi card
User code 11 (- - - -)
User code 11 Attributes
Adding a proxi card
Deleting a proxi card
061
062
063
070
071
072
073
080
081
082
083
090
091
092
093
100
101
102
103
110
111
112
113
Manager Menu
User code 6 (- - - -)
060
Address
LED 1
LED 2
LED 3
LED 4
LED 5
LED 6
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
DISARM
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
CA62 Control Panel - User’s Manual
23
User code 17 Attributes
Adding a proxi card
Deleting a proxi card
173
User code 17 (- - - -)
170
171
Deleting a proxi card
163
172
User code 16 Attributes
Adding a proxi card
User code 16 (- - - -)
160
161
Deleting a proxi card
153
162
User code 15 Attributes
Adding a proxi card
User code 15 (- - - -)
150
151
Deleting a proxi card
143
152
User code 14 Attributes
Adding a proxi card
141
User code 14 (- - - -)
140
142
Deleting a proxi card
133
User code 13 (- - - -)
130
User code 13 Attributes
Deleting a proxi card
123
Adding a proxi card
Adding a proxi card
122
131
User code 12 Attributes
121
132
User code 12 (- - - -)
120
STAY
BYPASS
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
Partition A
Partition B
STAY
BYPASS
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
Partition A
Partition B
STAY
BYPASS
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
Partition A
Partition B
STAY
BYPASS
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
Partition A
Partition B
STAY
BYPASS
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
Partition A
Partition B
DISARM
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
24
CA62 Control Panel - User’s Manual
User code 18 (- - - -)
User code 18 Attributes
Adding a proxi card
Deleting a proxi card
User code 19 (- - - -)
User code 19 Attributes
Adding a proxi card
Deleting a proxi card
User code 20 (- - - -)
User code 20 Attributes
Adding a proxi card
Deleting a proxi card
Chief Manager code (0000)
Chief Manager code Attributes
Adding a proxi card
Deleting a proxi card
Manager code 1 (- - - -)
Manager code 1 Attributes
Adding a proxi card
Deleting a proxi card
Manager code 2 (- - - -)
Manager code 2 Attributes
Adding a proxi card
Deleting a proxi card
181
182
183
190
191
192
193
200
201
202
203
210
211
212
213
220
221
222
223
230
231
232
233
Manager Menu
180
Address
LED 2
LED 3
LED 4
LED 5
LED 6
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
STAY
PROGRAM
Press the ENT button to delete a card.
Put the card close to the proximity reader.
BYPASS
Partition A
Partition B
6. Partition B
6. Partition B
Press the ENT button to delete a card.
Put the card close to the proximity reader.
5. Partition A
6. Partition B
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
Press the ENT button to delete a card.
Put the card close to the proximity reader.
5. Partition A
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
Press the ENT button to delete a card.
Put the card close to the proximity reader.
5. Partition A
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
DISARM
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
LED 1
CA62 Control Panel - User’s Manual
25
Adding a proxi card
Deleting a proxi card
Display memory LOG
Chime enable / disable
Zones Bypass
Setting the clock
Setting the date
242
243
300
400
500
600
601
Display memory LOG
Chime enable / disable
Zones Bypass
1
2
3
- Default settings.
Memory LOG file review.
ENABLED - LEDs ON
6. Partition B
LED 2
LED 3
LED 4
LED 5
LED 6
Memory LOG file review.
ENABLED - LEDs ON
Press a number of a ZONE which you want to bypass.
Use buttons 1 - 9 and combinations ARM+0 (Zone 10), ARM+1 (Zone 11) and ARM+2 (Zone 12),
DISABLED - LEDs OFF
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
LED 1
User Programming Menu
Setting the date ( DD:MM). Default setting → 01:01.
Setting the clock ( HH:MM). Default setting → 00:00.
Press a number of a ZONE which you want to bypass.
Use buttons 1 - 9 and combinations ARM+0 (Zone 10), ARM+1 (Zone 11) and ARM+2 (Zone 12),
DISABLED - LEDs OFF
Press the ENT button to delete a card.
Put the card close to the proximity reader.
5. Partition A
Enter a 4 or 6 digit code (depends on the programmed on ADDRESS 1001 in the Engineer menu)
(- - - -) means, that there are no set code combination
Change own code (- - - -)
0
User Menu
Manager code 3 Attributes
241
Address
Manager code 3 (- - - -)
240
SUPPLEMENT B - Table for Memory LOG Events
For convenience the table includes a graphic representation of the LEDs as they light up for the
respective event. A black digit on a white background indicates an extinguished LED and a white
digit on a black background indicates a lit up LED. Scroll from LED 1 to LED 6 to determine the correspondence between the event displayed on the keypad and the text in the table.
Example: Suppose the event displayed on the keypad is represented by a LED combination of 2,
3, 5 and 6. The table discloses the first LED 2 data entry. The next data entries disclose that of the
first LED 3. Next comes the first data entry of LED 5 and finally comes the first data entry of LED 6.
This is the data entry with the ordinal number of 27 “Quick arming”.
26
LED
Indication
Event
number

1
Burglary Alarm type event in xx zone
Zone No

2
Burglary Alarm type restoring event in xx zone
Zone No

3
Fire type alarm event in xx zone
Zone No

4
Fire type restoring event in xx zone
Zone No

5
Panic type alarm event in xx zone
Zone No

6
Panic type restoring event in xx zone
Zone No

7
Tamper type alarm event in xx zone
Zone No

8
Tamper type restoring event in xx zone
Zone No

9
Medical type alarm event in xx zone
Zone No
Description
Zone/
User No

10
Medical type restoring event in xx zone
Zone No

11
Burglary Alarm type xx zone bypass
Zone No

12
Burglary Alarm type xx zone bypass restoring
Zone No

13
Fire type xx zone bypass
Zone No

14
Fire type xx zone bypass restoring
Zone No

15
Panic type xx zone bypass
Zone No

16
Panic type xx zone bypass restoring
Zone No

17
Tamper type xx zone bypass
Zone No

18
Tamper type xx zone bypass restoring
Zone No

19
Medical type xx zone bypass
Zone No

20
Medical type xx zone bypass restoring
Zone No

21
Disarm by xx user
User No

22
Remote disarming by xx user
User No

23
Disarming by key-switch in xx zone
Zone No

24
Arming by xx user
User No

25
Remote arming by xx user
User No

26
Arming by key-switch in xx zone
Zone No

27
Quick arm type arming
-

28
Program mode entry
CA62 Control Panel - User’s Manual

29
Program mode exit

30
Entering ambush code by xx user
User No

31
Telephone line failure
-

32
Recovery of faulty telephone line
-

33
Unsuccessful communication
-

34
Periodic test message communication

35
Digital communicator manual test

36
Fuse blown
Manager No
-

37
Restored fuse
-

38
System default RESET
-

39
Loss of 220 V AC power supply
-

40
Restored 220 V AC power supply
-

41
Low battery charge level
-

42
Restored battery charge level
-

43
Activated zone with attribute “Write to log”
Zone No

44
Restored zone with attribute “Write to log”
Zone No

45
Activated zone with AUX attribute “24h Burglary”
Zone No

46
Activated zone with AUX attribute “AC LOST”
Zone No

47
Activated zone with AUX attribute “Battery Low”
Zone No

48
Activated zone with AUX attribute “GSM Link Trouble”
Zone No

49
Activated zone with AUX attribute “Gas Detector”
Zone No

50
Activated zone with AUX attribute “Refrigeration”
Zone No

51
Activated zone with AUX attribute “Loss of Heat”
Zone No

52
Activated zone with AUX attribute “Water Leakage”
Zone No

53
Activated zone with AUX attribute “Foil Break”
Zone No

54
Activated zone with AUX attribute “Low bottled gas level”
Zone No

55
Activated zone with AUX attribute “High temperature”
Zone No

56
Activated zone with AUX attribute “Low temperature”
Zone No

57
Restored zone with AUX attribute “24h Burglary”
Zone No

58
Restored zone with AUX attribute “AC LOST”
Zone No

59
Restored zone with AUX attribute “Battery Low”
Zone No

60
Restored zone with AUX attribute “GSM Link Trouble”
Zone No

61
Restored zone with AUX attribute “Gas Detector”
Zone No

62
Restored zone with AUX attribute “Refrigeration”
Zone No

63
Restored zone with AUX attribute “Loss of Heat”
Zone No
CA62 Control Panel - User’s Manual
27
Address: Bulgaria, 1407 Sofia, 14A Srebarna Str.
Tel.: (+359 2) 9694 800, Fax: (+359 2) 962 52 13
e-mail: [email protected]
18020599_English, RevA,05/2009
www.teletek-electronics.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement