Tetra LED Systems Power Supply GEPS12-180U-NA

Add to my manuals
3 Pages

advertisement

Tetra LED Systems Power Supply GEPS12-180U-NA | Manualzz

GE

Lighting

Installation Guide

12

Volt

Tetra

®

LED Systems Power Supply

(GEPS12-180U-NA)

Power Supply Features

• Supports Tetra miniMAX, Tetra MAX, Tetra PowerMAX,

Tetra PowerStrip and Tetra miniStrip lighting systems

• UL: Class 2 wiring per NEC Article 725.

• Limited to use in dry and damp locations.

• The suitability of rain enclosure shall be determined if

intended for wet location.

• Minimum 5 cm (2 in.) spacing from heat producing

components required.

• Minimum 4 to side and 1 in. spacing in compartment

surrounding component required.

• Three 60 watt output banks.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Disconnect power at fuse box or circuit breaker before servicing or

installing product.

• Properly ground Tetra ® power supply.

RISK OF FIRE

• Use only Tetra ® supply wire to make connection from Tetra ®

power supply to Tetra ® LED strip.

• Use only approved wire for input/output connection. Minimum size

18 AWG (0.82 mm 2 )

• Follow all local codes.

• Risk of electric shock or fire, do not connect outputs in series or parallel.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation électrique à la boîte de fusibles ou au disjoncteur

avant l’entretien ou l’installation du produit.

• Assurez-vous de correctement mettre à terre l’alimentation

électrique Tetra ® .

RISQUES D’INCENDIE

• N’utilisez que le fil d’approvisionnement Tetra ® pour faire la connexion

entre l’alimentation Tetra ® et la bande DEL Tetra

Taille minimum 18 AWG (0.82 mm 2 ).

• Respectez tous les codes locaux.

® .

• N’utilisez que des fils approuvés pour les entrées/sorties de connexion.

• Avrisques d’incendie ou de choc lectriques. Ne pas interconnecter les

bornes de sortie.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-003. Ce DEFR de la classe [A] est conforme à la NMB-003 du Canada.

imagination at work

Power Supply Installation

1 Mount power supply and remove junction box cover. Carefully remove knockout for AC line input wires. Install appropriate electrical fittings in the knockout holes for wire protection.

White

(neutral)

To Tetra LED System

Black

(line)

AC line

Output wires

2 Connect the supply wire that is attached to the Tetra LED System to the red (+) and black (-) output wires of the power supply as outlined in the “Electrical Connections” section of your LED system’s Installation

Instructions.

NOTE: Three 60 watt output banks per power supply. Do not interconnect output terminations.

3

Green with yellow stripe (ground)

Connect the AC line to the black (line) and white (neutral) input wires of the power supply and connect the branch circuit ground to the green wire with a yellow stripe (ground) wire using appropriately sized twist-on wire connectors.

NOTE: For installation in Canada, a disconnect switch of appropriate rating needs to be placed within 29.5 ft. (9 m) of primary side of the power supply. The switch voltage rating shall not be less than the branch circuit voltage. The switch must also support twice the amount of input current.

NOTE: When installing power supply, connect to the appropriate sized building breaker or disconnect device for line, neutral and ground connections, in accordance with National Electric Code (NEC) Article 600 and all local regulations.

NOTE: Exceeding maximum load per bank will cause the LEDs to dim or blink. Once the excess load is removed, cycle the input power to restart the power supply.

Retrofit Instructions

1. (Existing Signs Only) Prior to installation, survey the site for information regarding power and accessibility inside and outside the

building. Ensure that the branch circuit supplying the existing transformer or ballast will be within the voltage ratings of the new

LED power supply, and have a current rating not exceeding 20A, or that permitted by applicable local, state, or country electrical codes

(whichever is less).

2. (Existing Signs Only) Remove the existing lighting equipment to be replaced, such as neon tubing or fluorescent tubes; and associated

transformers and ballasts. Care should be taken not to break the existing neon or fluorescent tubes.

NOTE: Follow all federal and local regulations when disposing of neon tubing, fluorescent tubes, transformers and ballasts.

3. (Existing Signs Only) If removal of the existing lighting equipment eliminates the disconnect switch, as required by applicable local,

state, or country electrical codes; a new disconnect switch must be installed.

4. (Existing Signs Only) Make sure the removal of lighting equipment does not compromise the integrity of the sign body (i.e. water

intrusion). Fill in all holes 0.5 in. (13 mm) or smaller with the appropriate amount of rated caulk or sealant. For holes greater than

0.5 in. (13 mm), use an aluminum or zinc coated steel patch with rivets and sealant.

5. Using the layout guidelines within the LED module installation instructions, determine required number of LED modules required to

illuminate the sign.

6. Using the applicable LED module maximum Loading chart, determine the number of Tetra Class 2 Power Supplies required to power the

number of LED modules required to illuminate the sign, so as not to overload any single power supply output.

7. Follow the LED module instructions to properly mount the LED modules.

8. Connect the DC output of the power supply to the LED modules using the Power Supply Installation instructions above.

9. Connect AC power to the power supply in accordance with the applicable local, state, and country electrical codes, and the Power

Supply Installation instructions above.

10. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state, and country

electrical codes.

Power Supply Specifications

Performance Data

Input Voltage (VAC)

Input Frequency (Hz)

Input Current (A)

Output Voltage (VDC)

Output Current (ADC) - Each output

Output Power (W)

Environmental Operating Temperature Range

Environmental Humidity (non-condensing)

Environmental Storage Temperature Range

Dimensions

Min

108

-

-

11.0

-

-

-40°C

10%

-40°C

Typical

120-277

50/60

-

12.0

-

-

Max

305

-

2.0

13.0

5.0

180

+25°C

-

-

15.7 in. x 5.1 in. x 1.3 in. (400 mm x 130.6 mm x 32.6 mm)

+60°C*

90%

+85°C

*Maximum case temperature is 85°C

Supports

Tetra

Products SKUs

Tetra miniMAX

Tetra MAX GEMX71-2, GEMX50-2,

Tetra

PowerMAX

Tetra

PowerStrip

Tetra miniStrip

GEMM71-2, GEMM50-2,

GEMM41-2, GEMM32-2

GEMMBL-1, GEMMRD-1

GEMMGL-1

GEMMPO-1

GEMS71-1, GEMS50-1,

GEMS41-1, GEMS32-1

GEMX41-2, GEMX32-2

GEMXRD-1, GEMXGL-1,

GEMXBL-1

GEMXPO-1

GEMXRC-1

GEMXYG-1

GEMXH71-2, GEMXH50-2,

GEMXH41-2, GEMXH32-2

GEMXHRD-1

GEPM71-2, GEPM50-2,

GEPM41-2, GEPM32-2

GESS71-1, GESS50-1,

GESS41-1, GESS32-1

GESSH71-1, GESSH50-1,

GESSH41-1, GESSH32-1

GEWHBSP3, GEWWBSP3-50K,

GEWWBSP3-41K, GEWWBSP3

GEBSH71-1, GEBSH50-1,

GEBSH41-1, GEBSH32-1

Rated

Watts

0.324W

0.384W

0.312W

0.480W

0.384W/ module

0.456W/ module

0.480W/ module

0.360W/ module

0.288W/ module

0.540W/ module

0.720W/ module

0.408W/ module

1.32W

2.4W/ module

3.63W/ module

1.10W/ module

1.49W/ module

Maximum Load

170 modules/68 ft. (20.73m) per bank;

510 modules/204 ft. (62.18 m) per PS

150 modules/60 ft. (18.29 m) per bank;

450 modules/180 ft. (54.88 m) per PS

150 modules/60 ft. (18.29 m) per bank;

450 modules/180 ft. (54.88 m) per PS

120 modules/48 ft. (14.63 m) per bank;

360 modules/144 ft. (43.89 m) per PS

150 modules/60 ft. (18.29 m) per bank;

450 modules/180 ft. (54.88 m) per PS

128 modules/64 ft. (19.51 m) per bank;

384 modules/192 ft. (58.52 m) per PS

120 modules/60 ft. (18.29 m) per bank;

360 modules/180 ft. (54.88 m) per PS

160 modules/80 ft. (24.38 m) per bank;

480 modules/240 ft. (73.15 m) per PS

200 modules/100 ft. (30.48 m) per bank;

600 modules/300 ft. (91.44 m) per PS

106 modules/53 ft. (16.15 m) per bank;

318 modules/159 ft. (48.46 m) per PS

80 modules/40 ft. (12.20 m) per bank;

240 modules/120 ft. (36.59 m) per PS

142 modules/71 ft. (21.64 m) per bank;

426 modules/213 ft. (64.92 m) per PS

42 modules/28 ft. (8.53 m) per bank;

126 modules/84 ft. (25.60 m) per PS

20 modules/20.0 ft. (6.01 m) per bank;

60 modules/60.0 ft. (18.29 m) per PS

16 modules/17.0 ft. (5.18 m) per bank;

48 modules/51.0 ft. (15.60 m) per PS

53 modules/53 ft. (16.16 m) per bank;

159 modules/159 ft. (48.48 m) per PS

38 modules/38 ft. (11.58 m) per bank;

114 modules/114 ft. (34.75 m) per PS

18 AWG/

0.82 mm 2

15 ft.

(4.6 m)

15 ft.

(4.6 m)

15 ft.

(4.6 m)

15 ft.

(4.6 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

30 ft.

(9.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

20 ft.

(6.1 m)

Remote Mounting Distance

16 AWG/

1.31 mm 2

23 ft.

(7.0 m)

23 ft.

(7.0 m)

23 ft.

(7.0 m)

23 ft.

(7.0 m)

30 ft.

(9.1 m)

30 ft.

(9.1 m)

30 ft.

(9.1 m)

30 ft.

(9.1 m)

30 ft.

(9.1 m)

25 ft.

(7.6 m)

25 ft.

(7.6 m)

25 ft.

(7.6 m)

25 ft.

(7.6 m)

50 ft.

(15.2 m)

30 ft.

(9.1 m)

30 ft.

(9.1 m)

30 ft.

(9.1 m)

14 AWG/

2.08 mm 2

38 ft.

(11.6 m)

38 ft.

(11.6 m)

38 ft.

(11.6 m)

38 ft.

(11.6 m)

80 ft.

(24.4 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

50 ft.

(15.2 m)

35 ft.

(10.6 m)

35 ft.

(10.6 m)

35 ft.

(10.6 m)

35 ft.

(10.6 m)

12 AWG/

3.31 mm 2

65 ft.

(19.8 m)

65 ft.

(19.8 m)

65 ft.

(19.8 m)

65 ft.

(19.8 m)

120 ft.

(36.6 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

86 ft.

(26.2 m)

40 ft.

(12.1 m)

40 ft.

(12.1 m)

40 ft.

(12.1 m)

40 ft.

(12.1 m)

This product is intended to be used as a lamp control gear that is installed after the mains control switch.

Conforms to the following standards:

www.gelighting.com

GE and the GE Monogram are trademarks of the General Electric Company. All other trademarks are the property of their respective owners. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. GE Lighting is a business of the General Electric Company. © 2016 GE.

SIGN193 (Rev 11/17/16)

GE2027-2777

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement