Model #: G6005
PO #:
Serial #:
3-in-1 Convertible Crib (G6005)
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store from where it was purchased before contacting AFG Customer Service.
AFG Customer Service:
E-mail: [email protected]
Tel: (323) 722-6268
WARNING:
Failure to follow these warnings and the assembly instructions could result in serious injury or death.
Read all instructions BEFORE assembly and USE of product. KEEP
INSTRUCTIONS FOR FUTURE USE.
•
First remove hardware from box and sort by size. Check to see that all hardware and wooden pieces are present before assembling.
•
Follow instructions listed below in the proper sequence as numbered to assure fast, easy and correct assembly.
•
DO NOT use this crib if the enclosed or attached instructions cannot be strictly adhered to.
WARNING:
• DO NOT attempt to repair or modify parts with cracks or defects. Please contact us for immediate replacement.
• This product is for home use and is not intended for use in schools, day care centers or other commercial establishments.
• Must be assembled by a capable adult.
• CHOKING HAZARDS: DO NOT put small / loose components on top of the unit where baby could reach.
Crib Warning
CAUTION:Any mattress used in this crib should be at least 27−1/4 by 51−5/8 in. with a thickness not exceeding 6 in.
WARNING
:
Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
•
This crib conforms to applicable regulations promulgated by the Consumer Products Safety Commission.
•
Never use plastic shipping bags or other plastic film as mattress covers.
•
Infants can suffocation in gaps between crib sides and a mattress that is too small.
•
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless, otherwise advised by your physician.
•
DO NOT use a water mattress with this crib.
•
Do not remove any wood screws in the normal disassembly of the crib.
•
Replace teething rail if damaged, cracked or loose.
•
If refinishing, use a non−toxic finish specified for children’s products.
•
Follow warnings on all products in a crib.
•
•
Strangulation Hazard
Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings or pacifier cord. Do not suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
•
DO NOT place crib near windows where cords from blinds or drapes may strangle a child.
2015 AFG Baby Furniture G6005 Assembly Sheet ©
1
Fall Hazard
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads,
• large toys and other objects that could serve as steps for climbing out.
•
Stop using crib when child begins to climb out or reaches the height of 35 in. (89 cm).
•
Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other
fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact (AFG International
Products Inc) for replacement parts and instructional literature if needed. DO NOT substitute parts.
Storage: The crib must be kept in a dry and clean area. Solid wood tends to exchange moisture with the surrounding air and reacts to major changes in temperature and humidity. The ideal environment for the crib is at a temperature between 65 and 75 degrees and a relative humidity between 35 and 40 percent. If the room is too humid, the crib willabsorb moisture and expand; in verse, the crib will lose moisure and shrink in a dry environment. It is best to place your furniture away from heating or air−conditioning vents. Also, direct exposure to sunlight can discolor the wood, sodo not place your product where it will receive prolonged sunlight exposure.
Care and Cleaning: Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you choose to refinish this furniture, be sure to use only a non−toxic finish specified for childrens products.
Toddler Bed Warnings
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords, around a child’s neck. These items may catch on bed parts.
CAUTION:
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in the bed shall be a full−size crib mattress at least
51−5/8 in. (1310 mm) in length, 27−1/4 in. (690 mm) in width, and
6
in. (150mm) in thickness
(Max. 6 in (150mm).
•
The maximum weight shall not be greater than 50 lbs (22.7kg).
•
Do not use with less than 12 inches of space between toddler bed and solid objects such as a wall or dresser. Child could slide into smaller spaces and suffocate.
•
DO NOT use a water mattress.
•
DO NOT use casters on toddler bed.
•
Guardrails if provided must be used to avoid the formation of a gap between the mattress and the bed that could cause an entrapment. If mattress retention clips are provided they must be used to restrict mattress movement.
•
To avoid head injury, do not allow any child to play underneath the crib.
•
Never add any accessory such as a basinet or changingtable that extends over the sleepingarea.
2015 AFG Baby Furniture G6005 Assembly Sheet ©
2
G6005 Parts and Hardware Identification Sheet
DO NOT assemble crib if parts or hardware are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Parts ~
A. Headboard / Footboard
(2 pcs)
B. Rear Left Leg (1 pc) C. Rear Right Leg (1 pc) D. Left Side Panel (1 pc)
E. Right Side Panel (1 pc) F. Front Left Leg (1 pc) G. Front Right Leg (1 pc)
H. Top Rail (2 pcs) I. Stabilizer Bar (1 pc) J. Mattress Support (1 pc)
2015 AFG Baby Furniture G6005 Assembly Sheet ©
3
G6005 Parts and Hardware Identification Sheet
DO NOT assemble crib if parts or hardware are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Hardware ~
Item # Fittings Qty
1. Bolt M6 X 90mm
2. Dowel 8mm x 30mm
(8 pcs)
(12 pcs)
3. Bolt M6 X 55mm (12 pcs)
4. Barrel Nut M6 x 13mm (16 pcs)
5. Bolt M6 X 45mm (4 pcs)
6. Bolt M6 X 19mm (4 pcs)
7. Hex Wrench M4 X 57mm (1 pc)
FLATHEAD SCREWDRIVER (NOT INCLUDED)
2015 AFG Baby Furniture G6005 Assembly Sheet ©
4
A. Headboard / Footboard (2 pcs)
B.
Rear Left Leg (1 pc)
C. Rear Right Leg (1 pc)
D. Left Side Panel
E. Right Side Panel
F. Front Left Leg
G. Front Right Leg
H. Top Rail
J. Mattress Support
(1 pc)
(1 pc)
(1 pc)
(1 pc)
(2 pcs)
(1 pc)
2015 AFG Baby Furniture G6005 Assembly Sheet ©
5
G6005 Crib Assembly Sheet
STEP 1
a. Insert Dowels (#2) into each end of the Top Rail (H). b. Attach Top Rail (H) to Rear Left Leg (B) and Front Left Leg (F) by using 2 Bolts (#3) with Hex Wrench (#7). Do not tighten all bolts yet. This will make the attachment of the
Left Side Panel (D) easier. c. Attach Left Side Panel (D) to Rear Left Leg (B) and Front Left Leg (F) by using 4
Bolts (#3) and 4 barrel nuts (#4) into top and bottom holes. Tighten all bolts. d. Repeat above steps for the opposite side.
2. (4 pcs) 3. (12 pcs)
7. (1 pc) 4. (8 pcs)
2015 AFG Baby Furniture G6005 Assembly Sheet ©
6
G6005 Crib Assembly Sheet
STEP 2
a. Insert 4 Dowels (#2) into upper holes of each corner of Headboard (A). b. Attach Headboard to the legs on the left side and right side by using 4 Barrel Nuts
(#4) on the underside of each corner of Headboard before inserting 4 Bolts (#1) into top and bottom holes of legs. Tighten firmly with Hex Wrench (#7). c. Repeat above steps for the Footboard side.
1.
4.
(8 pcs) 2.
(8 pcs) 7.
(8 pcs)
(1 pc)
2015 AFG Baby Furniture G6005 Assembly Sheet ©
7
G6005 Crib Assembly Sheet
STEP 3
a. Attach Mattress Support (J) flat side up by swinging out the four hangers at the corners of the mattress support and use 4 Bolts (#6) to attach hangers to the brackets on the legs at an even level on all sides.
WARNING:
Make sure that the warning envelope on the
Mattress Support Frame is facing up.
WARNING:
Check components periodically, make sure hinges are tightened properly and securely.
Face Up
Warning
Envelope
6. (4 pcs) 7.
2015 AFG Baby Furniture G6005 Assembly Sheet ©
(1 pc)
8
G6005 Crib Assembly Sheet
CRIB ASSEMBLY COMPLETE.
WARNING:
Tighten all bolts and check height of Mattress Support Frame, make sure frame is at the same height at all 4 corners.
2015 AFG Baby Furniture G6005 Assembly Sheet ©
9
G6005 Toddler Bed Assembly Sheet
*Mattress Support Frame must be in the lowest position before installing guardrail.
a. Detach the front side bolts, disassemble the Footboard (A). b. Attach Guardrail (I) (Label Facing Outside) to front leg brackets with 4 Bolts (#5).
5 (4 pcs) 7.
2015 AFG Baby Furniture G6005 Assembly Sheet ©
(1 pc)
10
G6005 Full Size Bed Assembly Sheet
*Metal frame rails (not included) can be purchased at any furniture store*
a. Remove all the pieces from Headboard (A). Attach the headboard with Rear Left Leg
(B) and Rear Right Leg (C). Use this as the headboard for the full size bed. b. Attached the Footboard (A) with Front Left Leg (F) and Front Right Leg (G). This will also be the footboard. c. By using the bottom holes of the headboard and footboard, assemble the headboard and footboard together using the full-size metal-frame rails.
2015 AFG Baby Furniture G6005 Assembly Sheet ©
11
Safety Tips for Assembling and Re-assembling Cribs
•
Parents should not use any crib with missing, broken or loose hardware parts. Crib slats or spindles should be spaced no more than 2-3/8” apart, and none should be loose or missing. NEVER use a crib with corner posts over
•
1/16” of an inch above the end panels (unless they are over 16” high for a canopy).
Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact (AFG International Products Inc.) for replacement parts
•
• and instructional literature if needed. DO NOT substitute parts.
Never place infants to sleep on pillows, sofa cushions, adult beds, waterbeds, beanbags, or any other surface not specifically designed for infant sleep.
Always check all sides and corners of the crib to assure proper assembly with no openings that may entrap a child.
The crib mattress should fit snugly with no more than two fingers width, one-inch, between the edge of the mattress and the crib side. Otherwise, the baby can get trapped between the mattress and the side of the crib.
•
Do not try to repair any side of the crib without manufacturer-approved hardware.
•
Putting a broken side up against the wall is not a solution and can often make the situation worse.
•
When re-assembling the crib for your second child, please keep in mind that the screw holes will need to be filled in order for the screws to grip to the wood. Talk to your local hardware store or lumberyard about how to do it properly.
One year limited warranty
AFG International Products Inc. © wants you to be satisfied with any product that bears the AFG name or logo. We will provide promptly, at the request of the retailer, and without charge, any missing parts that have been reported, with proper description, within 7 days of the purchase of the products. Our warranty guarantees optimal workmanship and lack of significant defects. The product warranty lasts a year from the date of your purchase. Please keep the original receipt so that we may process your one year limited warranty request. This warranty only covers new units with original packaging.
Ownership of the warranty is non-transferable. The warranty does not cover any used, second-hand, or demo models. Our obligation under this warranty is to replace or repair the merchandise, at our option, free of charge. This warranty does not cover any damaged or defective parts that result from normal wear and tear, abuse, negligence, improper use or alteration to the finish design, and hardware. Specific rights issued by this warranty may vary from state to state. Some states do not allow limitations on how long implied warranties last. DO NOT return products to the store once a product is used, it cannot be resold and the materials and energy invested in the product would go to waste. In the event that AFG determines that a defect that may result from customer abuse or misuse, we will contact you with information about services and methods to prevent occurrences. We strongly recommend you register your product with our company by filling out registration and mailing it back to us. This ensures you are up-to-date with our products’ maintenance and information.
This warranty does not cover damage caused by accident, misuse or any use other than as intended and described in this assembly sheet or damage resulting from failure to maintain and clean this product as specified in this assembly sheet.
This warranty applies only to the original purchaser of the AFG International Products Inc. product.
CAUTION!
Safety Tips for Use of Cribs
Many older cribs, including secondhand or second use cribs, may not meet all current safety standards. For baby’s safety, even if you are on a tight budget, you should not purchase a used crib at a garage sale or accept a hand-me-down that does not meet the most recent Federal and
ASTM standards.
Thank you for choosing AFG.
MADE IN CHINA AFG ©
2015 AFG Baby Furniture G6005 Assembly Sheet ©
12
