Model ST-i CCD Camera Operating Manual

Model ST-i CCD Camera Operating Manual
Model ST-i
CCD Camera
Operating Manual
SBIG Astronomical Instruments,
A Division of Diffraction Limited.
| 59 Grenfell Crescent, Unit B, Ottawa, ON Canada, k2G 0G3
Tel: 613.225.2732 | Fax: 225.225.9688| E-mail: [email protected] |
We, Santa Barbara Instrument Group, a division of Aplegen, Inc., 147-A
Castilian Drive, Goleta, CA 93117 USA, (805) 571-7244, declare under
our sole responsibility that the Model ST-i CCD camera complies with Part
15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the receiver and the
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
A ferrite clip on the tracker cable must be used when operating this
You are also warned, that any changes to this certified device will void your
legal right to operate it.
Operating Manual for ST-i Series Camera
Revision 1.0
April 25, 2011
SBIG ST-i Manual
Table of Contents
Introduction ......................................................................................... 2
Getting Started .................................................................................. 2
Overview and Connections ............................................................... 3
Installing the Software on 32-bit and 64-bit Windows Systems ....... 4
Migrating Old Drivers from 32-bit to newer 64-bit Systems............ 9
Using the Camera Inside ................................................................... 11
Running CCDOps ........................................................................... 11
Getting Help.................................................................................... 11
Brightness and Contrast .................................................................. 14
Establishing a Link ......................................................................... 15
Camera Info .................................................................................... 16
Camera Setup.................................................................................. 17
Grab Command............................................................................... 18
Focus Command ............................................................................. 19
At the Telescope ................................................................................. 21
Finding and Centering the Object ................................................... 22
Taking an Image ............................................................................. 22
Further Adventures ......................................................................... 22
Acessories for your CCD Camera .................................................... 23
Tripod Mounting Ring .................................................................... 23
Camera Lens Adapters.................................................................... 23
Glossary .............................................................................................. 25
Appendix A – Connector and Cables ...................................................... 29
Telescope Jack ................................................................................ 29
Appendix B – Camera Specifications...................................................... 30
Appendix C – ST-i Color Camera Supplement...................................... 31
Appendix D – Dimensions and Backfocus .............................................. 39
SBIG ST-i Manual
Congratulations and thank you for buying one of our ST-i CCD cameras.
The ST-i has the following features:
Uses Kodak’s microlensed, KAI-0340 CCD with 648 x 486, 7.4
micron square pixels.
16-bit A/D converter with correlated double sampling .
Single board, small, compact design with internal mechanical
shutter allowing automatic dark frames, and electronic shutter for
exposures down to 0.001 seconds.
USB 2 interface yielding up to 2.0 megapixels per second
digitization rates with full backward compatibility with USB 1.1
computers at 400 kilopixels per second.
Input power provided through USB port.
Telescope interface with four optically isolated normally open
signals on the industry standard RJ-11 jack.
1.25" eyepiece sized barrel with threads for standard 1.25" filters.
Optional c-mount, t-thread and camera lens adapters available.
Powerful yet intuitive CCDOps software for guiding, image
acquisition and processing. Also comes with CCDSoftV5 and
TheSky version 5.
Getting Started
Very Important:
Before you attach the ST-i to your computer for the first time
you MUST install the software as described below
In addition to this Operating Manual, the ST-i package includes the
following items:
ST-i Camera – The camera body is approximately 1.25 x 3.5inches
USB Cable – Included is a 15-foot, USB 2 certified, A-to-B type, USB
cable. USB has a limit of 15-feet but the range can be extended
with active boosters.
Tracking Cable – This cable looks like a simple “RJ-11 telephone cable”
but in fact is a “6-pin reversed RJ-11 telephone cable”. Telescopes
require 6-pin autoguider cables and reversed means that, unlike
SBIG ST-i Manual
ordinary phone cables, this one flips the order of the wires. You
can tell a tracking cable from an ordinary cable by noting that with
tracking cables the tines that lock the RJ-11 jack into the receptacle
are both on the same flat side of the cable or when the ends are put
side by side the colored wires inside are in opposite order on the
two connectors.
Software – We include several CD-ROMs with the ST-i but the most
important one is labeled “SBIG Software and Catalog”. This
disc contains the drivers and CCDOps software you’ll need to use
the camera.
Overview and Connections
GUIDE PORT: This is where you connect the supplied 6 conductor
modular phone style cable to the Autoguider (sometimes labeled "CCD")
input port on your mount when using the ST-i as an autoguider, or when
using Track & Accumulate with mount corrections (see the CCDOPS
Manual for details of this mode
USB and POWER: Attach the 15-foot USB cable to any USB port on
your computer AFTER you have installed the drivers and software for the
ST-i. The USB port also provides power to the camera.
SBIG ST-i Manual
Installing the Software on Windows Systems
This section tells you how to do a fresh install of 64-bit drivers for SBIG
Cameras on your 32/64-bit Windows XP, Vista or Windows 7.
You should download and run the 64-bit Driver checker as described
below whether you are installing the ST-i camera on a 32-bit Windows
system such as XP, or a 64-bit version such as Vista 64 or Win 7.
Make sure no SBIG cameras are attached to your system.
Make sure your account has Administrator privileges then run the
SetupBitDriverChecker64.exe program to install the 64 Bit compatible
SBIG Driver Checker application on your system.
On 64-bit systems, find the icon for the SBIG Driver Checker by
opening the Start menu and typing SBIGDriver in the search box. The
icon should appear above the search box. Right click the icon and
select Properties then click the Compatibility tab. Click the “Run this
program as an administrator” as shown below and then hit the OK
Note: Under Vista and Windows 7 there are 2 levels of administrator
privileges: one at the account level and one at the program level. To
properly install the drivers the Driver Checker application requires
SBIG ST-i Manual
Run the Driver Checker application and it will ask you about any ST
Series Cameras (ST-7/8/9/10/2K) you may plan on using.
Prior to 2006 the ST Series cameras had only an internal Tracking
CCD. We call this the Classic Model. In 2006 we added the Remote
Guide Head capability to the ST Series and we call it the Pro Model.
The Driver Checker needs to know whether your ST Series camera is a
Classic Model or a Pro model. For the ST-i camera it does not matter
which option you select
SBIG ST-i Manual
After answering the Classic/Pro question above you'll see the following
dialog. The list of drivers shown may be different on your system but
it will generally indicate that no Installed Drivers were found and that
they all need to be updated.
Click the Update button and the Driver Checker will start to install the
SBIG drivers into your system.
Once the drivers have finished installing the Driver Checker will show
the following. At this point you can quit the Driver Checker.
SBIG ST-i Manual
8. Now it's time to try out the new drivers. With your camera
disconnected from the PC, then plug it into the PC with the USB Cable.
In the lower-right hand corner of the screen you see something like:
Followed by:
SBIG ST-i Manual
On systems running 32-bit Windows such as XP you may see this:
followed by the Hardware Wizard
Select "Install Automatically." If for some reason the Add New
Hardware Wizard asks you to manually locate the drivers then
navigate to the proper directory under the Driver Checker directory in
the Program Files or Program Files (X86) directory. There are 4
possibilities and you must choose the correct set of drivers. There are
directories for 32 Bit and 64 Bit drivers, based upon your version of
Windows and under them directories for Classic and Pro model
10. Run CCDOps and verify that you can establish a link to the camera.
SBIG ST-i Manual
Note: If you previously installed SBIG 32-bit drivers using the old 32bit Driver Checker program and now want to install 64-bit drivers
over the old installation, follow the procedure outlined below:
Migrating Old Drivers from 32-bit to newer 64-bit Systems
This section describes how to migrate drivers from the old 32-bit only
DriverChecker to the new 32/64-Bit Compatible DriverChecker64.
Uninstall the old DriverChecker software.
a. Run the Add or Remove Programs Control Panel in the
Start menu.
b. Click on the SBIG Driver Checker entry and then click
on the Change/Remove button.
Manually delete the old drivers files from the disk.
a. Delete the following files from the
C:\Windows\System32\Drivers directory:
sbigfldr.sys, sbiguldr.sys, sbiglldr.sys, sbigusbe.sys,
Some of these may not exist on your system but delete the
ones that do.
Manually delete the old drivers files from the Device Manager.
a. In the Start menu, point to All Programs, point to
Accessories, and then click Command Prompt.
b. At the command prompt, type the following command ,
and then press ENTER:
set devmgr_show_nonpresent_devices=1
c. Type the following command at the command prompt,
and then press ENTER:
start devmgmt.msc
d. In the View menu select the Show hidden devices
e. Expand the Universal Serial Bus controllers section by
click on the adjacent “+”
For each of the items listed below, right click on the item
then select Uninstall:
”SBIG USB Camera", ”SBIG ST-402 Camera", “SBIG
USB Loader", “SBIG ST-L Loader", “SBIG ST-402
SBIG ST-i Manual
Quit the Device Manager.
Install the new DriverChecker64 software.
a. Use the installer that came with your camera or download
it from our web site:
<www.sbig com>
Run the DriverChecker64 software.
a. From the Start menu select the DriverChecker64 item in
the SBIG folder.
b. Answer the question about your ST cameras.
Click the Update button to copy the new drivers to your system.
Link your old cameras to the new drivers.
a. For each type of SBIG Camera you own (ST, STL, ST402), power up the camera one at a time and then attach it
to the PC with the USB cable.
b. When the Add New Hardware Wizard comes up select
“No, not this time” when it asks if it can connect to
Windows Update then click Next.
c. Select “Install the software automatically” and click
d. If Windows asks you for the best match select any of the
entries with Version then click Next.
e. Click Finish and then you’ll have to go through steps b
through d one more time for this camera.
f. Repeats steps a through f for each SBIG camera.
When you’re all done your camera should show up in the Device Manager
in the SBIG USB Devices section as shown below:
Updating CCDOps and Drivers
We are constantly adding new features and fixing software bugs in our
software, which is available for free download from our web site. You
should periodically visit our website to check for updated versions of the
CCDOps software and you should also periodically run the Driver Checker
to download and update your drivers. To find the latest software and
drivers, go to: -> Software Downloads
SBIG ST-i Manual
Using the Camera Inside
When you first receive the ST-i it’s wise to get acquainted with its operation
inside the house where it’s warm and not to try to struggle with the
telescope operation in the dark. We’ve included a brief tutorial below to get
you acquainted with the ST-i and the CCDOps software.
Running CCDOps
Once installed, it’s easy to run CCDOps from the Windows Start menu.
Click the Start Menu, then find the SBIG Folder, which under Windows
XP is under the All Programs section. Finally click the CCDOps Icon to
start the program. You’ll be presented with the startup About Dialog that
shows the SBIG logo and the version of CCDOps. To dispense with it click
anywhere in the dialog other than the two blue fields or simply wait and the
dialog will close itself.
Getting Help
CCDOps includes an extensive help file that can be accessed through the
Help Topics item in the Help menu. In addition many of the
dialogs have an embedded Help button that will take you to the
Help Topic for that specific command. Just remember, help is
always just a click away.
Opening and Inspecting Dark Frames
We’ve included some sample images on the SBIG Software and Catalog
CD-ROM to get you acquainted with what you should expect from your
First, let’s look at what is called a dark frame. In the File menu use
the Open command and then navigate to the CD-ROM’s Images directory.
Double-click on the ST-i Tutorial folder to show its contents. Finally
double-click on the Image 1 – Sample Dark Frame icon to open the image.
CCDOps will present you with a dialog listing all the parameters
associated with the image such as the Exposure Time, the Date and Time
the image was acquired, etc. Note that the Exposure Time was 1.0 second.
Spend some time inspecting the data then click in the dialog to close it.
Data like this is always attached to saved images and you can show it
using the Parameters command in the Display menu. After the Image
Parameters dialog has gone you’ll see the image displayed in its own
window and the Contrast dialog will appear. The image is shown below:
SBIG ST-i Manual
This is what’s referred to as a dark frame and it’s what you get when you
take a picture with the nosepiece covered and the shutter closed. It’s a
picture in the dark. Although there’s not much interesting to look at in this
image there are some very important features that you need to understand.
The first thing you’ll see is that while the image looks mostly like salt
and pepper there are hundreds of bright specks. These are called hot pixels.
They are present in every CCD image to one extent or another, even in
images from our most expensive cameras. If your digital snappy camera
didn’t automatically remove them for you, they would be seen in those
images too.
What causes hot pixels? It’s an attribute of CCD sensors called dark
current. A pixel in an ideal CCD, in the absence of light, would maintain a
steady value. When exposed to light the pixel’s value would increase in
response to the light but then as soon as the light went away the pixel would
maintain its value again.
In the real world CCD pixels suffer from the affects of dark current
whereby the pixel’s value slowly increases (brightens) over time. All the
pixels in the image shown above have some component of their signal due
to the build up of dark current.
Dark current builds up over time in a linear fashion. Cameras designed
for taking long exposures provide TE cooling of the CCD to reduced the
rate at which it accumulates. However, for the typically short exposures
used in planetary imaging and guiding, cooling is unnecessary if the camera
can otherwise take and subtract dark frames.
SBIG ST-i Manual
Hot pixels are simply the pixels where the dark current is higher than
the average and thus they show up as white specs against the salt and
pepper background. Again, this is completely normal for CCD images.
The second effect you’ll notice is a brightening on the left of the image,
as if something bright was just outside the field of view. This is called the
readout glow and is caused by the electronics in the CCD, in particular by a
very small but ever present glow emanating from the on-chip amplifier that
conditions the weak signals in the CCD so that they may be digitized.
The readout (or digitization) of images from CCDs is a sequential
process whereby every pixel is digitized one-after-another until the whole
image has been digitized. The readout starts at pixel (1,1) in the top-left
corner and proceeds to pixel (648 x 486) in the lower-right hand corner. As
each pixel in a row is readout the pixels to the right of it within the same
row are shifted to the left one position in preparation for the next pixel's
readout. The next pixel is then readout and the process repeated until every
pixel in the first row has been digitized.
At this point the whole CCD is shifted up one row and digitization
starts with the left-most pixel of the second row. The readout glow on the
left of the images is a buildup of light from a glow from the preamplifier
structures in the upper-left hand corner of the CCD while rows are queuing
up for readout.
The final effect you’ll notice is the salt-and-pepper look of the
background. What you’re seeing here is the ultimate noise floor of the
CCD whereby adjacent pixels have slightly different values due to noise in
the CCD and readout electronics. The noise in dark frames that have zero
exposure time is referred to as the read noise of the camera.
Fortunately for us there are very simple image processing techniques
we can use to eliminate the effects of dark current and readout glow.
Let’s open another image. Close the first image by clicking the X in
the upper-right corner then use the Open command in the File menu again
but, this time double-click on Image 2. Note in the Image Parameters
dialog that this image had an Exposure Time of 10 seconds. Click in the
dialog to close it.
Now this image has a whole lot more hot pixels! That’s because this
exposure was 10 times as long and the pixels built up 10 times the dark
current. It’s hard to even see the background through all the hot pixels.
About this time you’re probably asking yourself “How can I ever take
images with all these hot pixels?” The answer is simple. Because the build
up of dark current is a repeatable effect you can remove the effects of dark
current by taking two images, one with the shutter open (light frame) and
another of equal exposure with the shutter closed (dark frame). You then
subtract the dark frame from the light frame, and because the hot pixels and
the readout glow repeat from one image to another they are removed by the
Let’s see how this works. Close Image 2 and Open Image 3, which is
a 10-second light frame where you can get a hint of the object but the hot
SBIG ST-i Manual
pixels are definitely obscuring it. Now use the Dark Subtract command in
the Utility menu. This brings up the Open File dialog where CCDOps
wants you to select which image to subtract. Double-click on Image 2, the
10-second dark frame. The displayed image turns completely black! What
did we do? Did we destroy the image by dark subtracting? No we didn’t
but it’s time to learn something else regarding CCD images.
Brightness and Contrast
Images from the ST-i are 16-bit images meaning any pixel can have values
from 0 to 65,535 ADU where ADU is short for A/D Converter Units. Said
another way this means there are 65,536 possible brightness or gray scale
values that each pixel can have. In CCD lingo this is referred to as the
dynamic range. But computer monitors and our eyes can typically only
distinguish a hundred or so different gray scale values. How do we
accommodate the large dynamic range of CCD images with our computer?
The answer is through Brightness and Contrast adjustments of the
displayed image.
Getting back to our dark subtracted image and why it’s completely
black. Find the Contrast dialog shown
to the right and then click the Auto
checkbox. Magically our object
appears, and as promised, the hot pixels
and the readout glow are gone, replaced
by the object and the salt-and-pepper
noise. What did we do?
By clicking the Auto checkbox we
told CCDOps to adjust the image
display to match the actual image’s
pixel values. Auto Contrast is a very
handy tool to have in your bag of tricks.
Just for fun click the Smooth checkbox in the Contrast dialog. The
noise in the image is greatly reduced. The Smooth option is handy when
for reducing the noise in underexposed images like Image 3.
Let’s explore the Contrast dialog further. Close the dark subtracted
Image 3 and when CCDOps asks you if you want to save the changes
you’ve made click No. Use the Open command again to open Image 4,
which is just like Image 3, but with a proper exposure.
The first thing to notice is that in the Contrast dialog the Back is set to
8,000 and the Range is set to 20,000. What does that mean? In short it
means that pixel values from 8,000 (Back) to 8,000+20,000 (Back +
Range) have been displayed using the monitor’s available gray scale.
Pixels with values 8,000 ADU or below are completely black. Pixels with
values 8,000+20,000=28,000 ADU or above are completely white. Finally,
pixels with values between 8,000 and 28,000 are shades of gray.
Click the small up and down buttons adjacent to the Back setting
several times and you’ll see the overall image brightness increase
SBIG ST-i Manual
and decrease. Click the ones adjacent to the Range setting and you’ll see
the image contrast increase and decrease. Here’s a summary of how this
Increasing the Back decreases the image brightness and vice-versa.
Increasing the Range decreases the image contrast and vice-versa.
Set the Back to 8,000 and the Range to 20,000 by typing in the fields
(without the comma) and then hit the Apply button to get us back to where
we started. When you manually enter values in the Back and Range you
must hit Apply to see the effect.
Let’s learn a little more about the controls in the Contrast dialog. Click
the Invert checkbox and notice that the image now looks like a negative.
For images of faint objects, viewing the image as a negative by clicking
Invert can reveal faint structure.
Unclick Invert and then click Sharpen on and off several times while
looking at the fine detail in the image. With the Sharpen checked it’s
almost as if the focus improves. That’s the effect of Sharpen. It works
great on well-exposed images but tends to increase the noise in faint areas.
The last thing to try in the Contrast dialog is the Mag popup. It’s set to
1:1 but selecting 2:1 or 4:1 zooms in on the image, enlarging the image
display. Selecting 1:2 or 1:4 zooms out on the image. Try the 1:2 and 2:1
settings. You may wonder if all these changes to the Contrast dialog are
destructive to the image data. They are not.
Changes to the settings in the Contrast dialog only affect the way the image
is displayed. They do not modify the actual pixel values.
In Summary
• Clicking Auto is a good place to start with most images.
• Back controls image brightness and Range controls contrast.
• Clicking Invert can help reveal faint detail in images.
• Clicking Smooth can reduce the noise in underexposed images.
• Clicking Sharpen reveals additional detail in well-exposed images.
Establishing a Link
It’s time to actually connect up to your camera and take some images. If
you haven’t installed the drivers already go back to Section 2 and do so
If you’ve taken a break from the tutorial and the camera isn’t powered
up and attached to the computer do so now by connecting the USB cable
between the camera and the computer. At this point the green LED on the
back of the camera should be on.
SBIG ST-i Manual
Use the Graphics/Comm Setup command in the Misc menu to make
sure USB is selected for the Interface. Click OK to set/confirm that and
then use the Establish COM Link command in the Camera menu.
CCDOps will try to connect to your camera, which can take several
seconds to complete. If successful you’ll hear the shutter emit a series of
clicking sounds as it finds home and you’ll see updated information in the
Link Status fields show in the lower-right corner of the CCDOps window
as shown here:
This shows the link has been established to your camera. It should say ST-i
in the status bar as shown above.
Camera Info
After establishing a link to the ST-i use the Information command in the
Camera menu and you’ll see a dialog box similar to the one below:
The Camera Information command shows you the capabilities of your
camera. There are a few key items here that you should be aware of should
you ever need technical support:
Firmware Version/Driver Info – Over time we revise the camera firmware
and drivers to add new capabilities and fix software bugs. The STi actually has its firmware downloaded to it every time it connects
to the PC after a power-up sequence, which makes it very easy for
us to update the ST-i in the field. To make sure you have the latest
firmware periodically run the Driver Checker, which checks our
servers for later drivers and updates your system accordingly.
Serial Number – If you ever need to know this, here it is. It’s on the label
on the back of the camera as well.
Readout Mode Table – This shows the various readout modes the ST-i
supports. The High-resolution mode offers the full 648 x 486
SBIG ST-i Manual
resolution with 7.4 micron square pixels. The ST-i also supports
binning whereby groups of pixels are combined to form a single
larger pixel. This reduces the resolution but increases the
sensitivity as larger pixels capture more light. The Low-resolution
modes utilize 2x2 binning as you can see by the Image
Height/Width and Pixel Size entries.
Finally, review the information presented, then close the dialog by clicking
in it.
Camera Setup
Use the Setup command in the Camera menu to see the ST-i Camera Setup
dialog shown below.
The key items in this dialog are described individually below.
Resolution mode – This popup controls the readout mode discussed in the
Camera Information section above. You can select the High or
Low resolutions modes directly but we recommend you start with
the Auto resolution mode. In Auto mode the camera uses the highresolution mode everywhere except in the Full Frame Focus
mode (discussed below) where it uses the low-resolution mode to
speed up the image throughput.
Reuse dark frames – This is a handy feature and you should set it to Yes.
What that means is that when you’re taking images where you
want to subtract dark frames the software will reuse a previously
captured dark frame if it’s the same exposure time and at the same
CCD temperature.
You can read about the other items in the Help but for now just leave them
set the way they are. Click OK to register your changes.
SBIG ST-i Manual
Grab Command
Let’s take a dark frame with your new camera. If you haven’t done so
already, screw in the nosepiece and put the rubber cap on it. While the
shutter was designed to block light from the telescope for dark frames, it
can’t block flooding room light from leaking around the edges of the shutter
blade. That’s why you should cover it under bright light illumination.
Now, use the Grab command in the Camera menu and set the dialog as
shown below:
Here we’re asking for a 1 second dark frame of the full CCD. Click the OK
button and in a few seconds you’ll see an image that looks a lot like the
Image 1 from the tutorial. Hot pixels, readout glow and salt-and-pepper
noise, they’re all there. Congratulations: You’ve just taken your first dark
frame! That wasn’t so hard was it?
Let’s experiment with the settings in the Grab dialog. Try changing the
Exposure Time to 10 seconds and grabbing another image but this time
watch the LED on the back of the camera. It blinks while the camera is
exposing the image. That’s a handy thing to remember when you’re in the
observatory. Don’t bump the telescope when the LED is blinking.
Anyway, the new image should look just like Image 2. Try setting the
Exposure Time back to 1.0 and the Dark frame to Also. What happens
here is the camera takes a dark frame first, and then takes a light frame,
subtracting the dark frame from it. The result should be uniform noise
without hot pixels and without readout glow.
Had we had the camera on the telescope we would have seen the object
but because we had the nosepiece covered we took a dark subtracted image
of the dark. If you take enough of these, and stare at them long enough
you’ll see all kinds of patterns in the random noise, including even pictures
of Elvis!
You can read about the other items in the Grab dialog by clicking the
Help button, but in general the Grab command is used to take a single
image and optionally do an automatic dark subtraction.
SBIG ST-i Manual
Note: Dark subtracted images have an offset of 100 ADU added to them to
ensure values near zero are not clipped.
Focus Command
Using the Grab command to focus your telescope would drive you crazy,
taking a single image at a time, tweaking the telescope, etc. Instead we use
the Focus command, which is like Grab but it takes image after image
automatically. Use the Focus command in the Camera menu and set it up
in the Focus Setup dialog as shown below:
Click OK and the camera will go into Focus mode. You’ll see image after
image appear in a single window at a rate of several frames each second.
The images will vary slightly from image to image, mostly in the random
background noise, but in general they’ll all look a lot like Image 1. You’ll
also notice that a new Focus Mode dialog appeared.
Here’s a brief description of the key items in the Focus Setup and Focus
Mode dialogs.
Exposure Time – You’ll be able to see most objects in a 1 second
exposure. Use shorter exposures (down to 0.001 seconds) for
faster rep rates when focusing on bright stars or longer exposures
when trying to center dim objects. The first time you focus it helps
to use an exposure of about 3 seconds so that you can see even out
of focus stars. As the stars are brought to sharper focus you can
reduce the exposure time.
SBIG ST-i Manual
Frame Size – Planet mode allows you to select a portion of the CCD’s
field of view (FOV) for faster rep rates due to smaller downloads.
It’s great for focusing the telescope on a star. The other three Full
settings all show the full FOV of the CCD but are slower than
Planet mode because there’s more data to download.
Full-High uses high-resolution mode to show you all 648 x 486
pixels. Full-Low uses low resolution (2x2 binning) which is faster
and more sensitive since there are fewer pixels to download and
the pixels are larger. Finally Full works in conjunction with
Planet mode and the Camera Setup such that when the camera is
set to Auto resolution mode Full uses the low-resolution mode for
faster downloads then switches to high-resolution for Planet mode.
Dark Frames – For most objects you won’t need to take dark frames in
Focus mode to frame and focus the object because the exposures
tend to be short and the build up of dark current minimal. On
some dim objects though, checking this item, which uses dark
subtracted images for Focus mode, can help to pull the object out
of the noise. The update rate is slightly slower when using dark
frames so only use this when you need to.
Filter Warm Pix – Checking this box will cause the software to
automatically filter out warm (bright) pixels. This will produce a
smoother background. with less "salt-and-pepper" appearance.
Update Mode – Sometimes you want to tweak the focus, look at an image,
tweak it again, etc. Setting this to Manual causes the Focus mode
to pause between images until the Space Bar is hit or you click the
Pause/Resume button.
Exposure delay – This will put a delay of x seconds between exposures
Turbo Mode – This is used with slower cameras to stop the shutter from
moving in order to speed up focusing. It is not needed with the
ST-i camera.
Peak – This shows the position and brightness of the brightest pixel in the
Focus mode image. We’ll use this later to get the best focus by
maximizing the Peak on a star.
Pause/Resume – Click this button at any time to pause or resume the focus
mode. This can be handy for going back and forth between the
telescope and the computer or for studying the images.
You can read more about the other items in the Help but we now know
enough for basic operation. Exit Focus Mode by closing the Focus Mode
dialog or closing the image window.
SBIG ST-i Manual
At the Telescope
Connect the camera to the computer and start CCDOps. Establish a link to
the camera and run the Camera Setup command. At this point we’re ready
to hook up to the telescope.
Focusing the ST-i camera is much easier than most CCD cameras due
to its faster frame rates. Nevertheless, it can be difficult the first time when
the star images are likely to be well out of focus and difficult to detect.
Use 3 second exposures the first time in order to detect even stars that are
out of focus. As you get closer to focus you can reduce the time to increase
the update rate and use just the brightest stars for final focusing. The
backfocus distance (the distaqnce from the front of the camera tube to the
CCD focal plane) is 0.53 inches.
To achieve fine focus, first center a bright star then insert the CCD
head into the eyepiece tube, taking care to seat it, and then enter the
CCDOps Focus Mode. Do not initially try to focus on the moon or planet –
they are harder. As we learned in the tutorial, the Focus Mode
automatically displays successive images on the screen as well as the peak
brightness value of the brightest object in the field of view. Using the
telescope controls, center the star image in the CCD, and adjust the focus
until the star image is a small as can be discerned. Next, shift the telescope
to fainter stars so the CCD is not saturated. Further adjust the focus to
maximize the displayed star brightness in counts and minimize the star
diameter. This can be tedious. It helps considerably if a pointer or marker
is affixed to the focus knob so you can rapidly return to the best focus once
you've gone through it.
With the fast update rate of the ST-i camera, use the Full frame mode
to focus, or screen update rate can be increased significantly by using
Planet mode. In Planet mode the Focus command takes a full image and
then lets you position a variable sized rectangle around the star. On
subsequent images the Planet mode only digitizes, downloads, and displays
the small area you selected. The increase in frame rate is roughly
proportional to the decrease in frame size, assuming you are using a short
The telescope focus is best achieved by maximizing the peak value of
the star image. You should be careful to move to a dimmer star if the peak
brightness causes saturation. The saturation levels of the various resolution
modes are shown in Table 3.2 below. Another point you should also be
aware of is that as you approach a good focus, the peak reading can vary by
30% or so. This is due to the fact that as the star image gets small, where an
appreciable percentage of the light is confined to a single pixel, shifting the
image a half a pixel reduces the peak brightness as the star's image is split
between the two pixels. The Kodak CCD pixels are so small that this is not
likely to be a problem.
SBIG ST-i Manual
High Res
Med/Low Res
Saturation Counts
Once the best focus is found, the focusing operation can be greatly
shortened the second time by removing the camera, being careful not to
touch the focus knob, and inserting a high power eyepiece. Slide it back and
forth to find the best visual focus (don’t touch the focus knob), and then
scribe the outside of the eyepiece barrel. The next time the camera is used
the eyepiece should be first inserted into the tube to the scribe mark, and the
telescope visually focused and centered on the object. At f/6 the depth of
focus is only 0.005 inch, so focus is critical. An adapter may be necessary
to allow the eyepiece to be held at the proper focus position.
Finding and Centering the Object
If you have difficulty finding an object after obtaining good focus, check to
be sure that the head is seated at best focus, then remove the head and insert
a medium or low power eyepiece. Being careful not to adjust the focus
knob on the telescope, slide the eyepiece in or out until the image appears in
good focus. Then visually find and center the object, if it is visible to the
eye. If not, use your setting circles carefully. Then, re-insert the camera
and use the Focus Mode with an exposure time of about ten seconds, if the
object is quite dim. Center the object using the telescope hand controls.
Taking an Image
Take an image of the object by selecting the Grab command and setting the
exposure time. Start out with the Image size set to full. The camera will
expose the CCD for the correct time, and digitize and download the image.
One can also automatically take a dark frame immediately before the light
image using the Grab command by selecting the Dark Also option. This is
useful for really dim objects.
Saving Images
Save the images using the Save command in the File menu. We strongly
recommend you save images in SBIG Compressed or FITS format as they
are the most compatible. Use the TIFF and JPEG formats only when you
are done with the image as you won’t be able to reopen it with CCDOps.
Those formats are useful for exporting to image processing programs.
Further Adventures
At this point we refer you to the CCDOps Manual that can be found on the
SBIG Software and Catalog CD-ROM. It has an extensive tutorial section
and detailed information about the software and its capabilities.
SBIG ST-i Manual
Accessories for your CCD Camera
This section describes several of the common Accessories designed to work
with the ST-i.
Tripod Mounting Ring
The tripod mounting ring is a split ring that clamps around the ST-i body
and provided a 1/4-20 threaded hold for mounting to a piggyback mount or
tripod mount.
Camera Lens Adapters
There are several adapters available for the ST-i to allow the use of camera
lenses and the SBIG eFinder or other third party accessories:
C-mount Adapter - this adapter crews into the 1.25" filter threads on
the front of the camera and enables use of the ST-i with standard C-Mount
camera lenses.
C-to-F Mount Adapter - this 35mm lens adapter allows the use of
Nikon 35mm camera lenses. It requires the C-mount Adapter.
C-to-T-thread Adapter - this adapter provides a t-thread for
attachment of the SBIG eFinder lens or other t-thread compatible accessory.
It requires the c-mount adapter. You will also need the tripod mounting
UV/IR Blocking Filter
We recommend the UV/IR blocking filter for use with the color version of
the ST-i camera to achieve the proper color balance.
SBIG ST-i Manual
ST-i Options:
1.25" Filter (UV/IR filter recommended for color camera)
C-mount adapter
C-mount lens (SBIG offers 100mm FL f/2.8 for guiding)
C-to-T Adapter
C-to-F Adapter
eFinder Assembly
35mm Nikon or Canon FD lens (user supplied)
Tripod Mounting Ring with 1/4-20 threaded base
SBIG ST-i Manual
Antiblooming- When a CCD pixel has reached its full well capacity,
electrons can effectively spill over into an adjoining pixel. This is
referred to as blooming. Kodak CCDs like the KAF-0402LE with
the antiblooming option can be used to help stop or at least reduce
blooming when the brighter parts of the image saturate.
Astrometry - Astrometry is the study of stellar positions with respect to a
given coordinate system.
Autoguider - All SBIG CCD cameras have auto guiding or "Star Tracker"
functions. This is accomplished by using the telescope drive
motors to force a guide star to stay precisely centered on a single
pixel of the CCD array. The camera has four relays to control the
drive corrector system of the telescope. The CCD camera head is
installed at the guide scope or off axis guider in place of a guiding
CCD - The CCD (Charged Coupled Device) is a flat, two dimensional array
of very small light detectors referred to as pixels. Each pixel acts
like a bucket for electrons. The electrons are created by photons
(light) absorbed in the pixel. During an exposure, each pixel fills
up with electrons in proportion to the amount of light entering the
pixel. After the exposure is complete, the electron charge buildup
in each pixel is measured. When a pixel is displayed at the
computer screen, its displayed brightness is proportional to the
number of electrons that had accumulated in the pixel during the
Correlated Double Sampling - Correlated Double Sampling (CDS) is
employed to lower the digitization errors due to residual charge in
the readout capacitors. This results in lower readout noise.
Dark Current - Dark Noise or Dark Current is the result of thermally
generated electrons building up in the CCD pixels during an
exposure. The number of electrons due to Dark Noise is related to
just two parameters; integration time and temperature of the CCD.
The longer the integration time, the greater the dark current
buildup. Conversely, the lower the operating temperature, the
lower the dark current. This is why the CCD is cooled for long
integration times. Dark noise is a mostly repeatable noise source,
therefore it can be subtracted from the image by taking a "Dark
Frame" exposure and subtracting it from the light image. This can
usually be done with very little loss of dynamic range.
Dark Frame - The user will need to routinely create image files called
Dark Frames. A Dark Frame is an image taken completely in the
SBIG ST-i Manual
dark. The shutter covers the CCD. Dark Frames are subtracted
from normal exposures (light frames) to eliminate fixed pattern
and dark current noise from the image. Dark Frames must be of the
same integration time and temperature as the light frame being
FITS Image File Format - The FITS image file format (which stands for
Flexible Image Transport System) is a common format supported
by professional astronomical image processing programs such as
IRAF and PC Vista.
Flat Field - A Flat Field is a image with a uniform distribution of light
entering the telescope. An image taken this way is called a flat
field image and is used with CCDOPS to correct images for
Focal Reducer - A Focal Reducer reduces the effective focal length of an
optical system. It consists of a lens mounted in a cell and is usually
placed in front of an eyepiece or camera. With the relatively small
size of CCDs compared to film, focal reducers are often used in
CCD imaging.
Full Well Capacity - Full Well Capacity refers to the maximum number of
electrons a CCD pixel can hold. This number is usually directly
proportional to the area of the pixel.
Histogram - The Histogram is a table of the number of pixels having a
given intensity for each of the possible pixel locations of the image
Light Frame - The Light Frame is the image of an object before a Dark
Frame has been subtracted.
Photometry - Photometry is the study of stellar magnitudes at a given
wavelength or bandpass.
Pixel Size - The smallest resolution element of a CCD camera is the CCD
Planet Mode - Planet Mode is the most useful way to achieve focus. When
you select Planet mode, a full frame is exposed, downloaded, and
displayed on the computer monitor. A small window can be placed
anywhere in the image area and the size of the window can be
changed. Subsequent downloads will be of the area inside the box
resulting in a much faster update rate.
Quantum Efficiency - Quantum Efficiency refers to the fractional number
of electrons formed in the CCD pixel for a given number of
photons. Quantum Efficiency is usually plotted as a function of
SBIG ST-i Manual
Readout Noise - Readout noise is associated with errors generated by the
actual interrogation and readout of each of the CCD pixels at the
end of an exposure. This is the result of fixed pattern noise in the
CCD, residual charge in the readout capacitors and to a small
extent the noise from the A/D converter and preamplifier.
Resolution Mode - The resolution of a CCD camera is determined by pixel
size. Pixel size can be increased by combining or binning more
than one pixel and displaying it as one pixel. Doing so decreases
the effective resolution but speeds up the download time of the
image. Maximum resolution is determined by the size of the
individual CCD pixel. The ST-i can run in High, Medium, Low
and Auto resolution modes.
Response Factor - Response Factor is a multiplier used by CCDOps to
calibrate CCDOps to a given telescope for photometric
Saturation - Saturation refers to the full well capacity of a CCD pixel as
well as the maximum counts available in the A/D converter. The
pixel is saturated when the number of electrons accumulated in the
pixel reaches its full well capacity. The A/D is saturated when the
input voltage exceeds the maximum.
Sky Background - The sky background illumination or brightness is the
number of counts in the image in areas free of stars or nebulosity
and is due to city lights and sky glow. High levels of sky
background can increase the noise in images just like dark current.
For some objects deep sky filters can be used to reduce the sky
background level.
Seeing - Seeing refers to the steadiness and the clarity of the atmosphere
during an observing session.
TE Cooler - The TE Cooler is a Thermal Electric cooling device used to
cool the CCD down to operating temperature. The CCD is
mounted to the TE Cooler which is mounted to a heat sink, usually
the camera head housing (Note: TE cooling is not used on the ST-i
TIFF Image File Format - The TIFF image file format (which stands for
Tagged Interchange File Format) was developed jointly by
Microsoft and Aldus Corporations to allow easy interchange of
graphics images between programs in areas such as presentation
and desktop publishing. CCDOps can save image files in this
format but unless they’re color images it can not read them.
Track and Accumulate - The Track and Accumulate function is a SBIG
patented feature of CCDOps that allows the user to automatically
SBIG ST-i Manual
co-register and co-add (including dark frame subtraction) a series
of images of an object. These exposures can be taken unguided as
long as the "Snapshot time" does not exceed the length of time
before tracking errors of your clock drive become apparent. This
allows you to image and track without guiding or the need to
connect the CCD Relay port to your drive motors.
Track List - The Track List is an ASCII file generated by CCDOPS during
a Track and Accumulate session. The Track List logs all the
corrections made by CCDOPS for each of the images. Track lists
are required when flat fielding Track and Accumulate images.
Tri-Color - Tri-Color refers to color images created using three different
colors mixed into a balanced color image using red, green and blue
filters. An object is imaged three times, once with each color filter.
The three images are then co-added and color balanced with the
appropriate software.
Vignetting - Vignetting is obstruction of the light paths by parts of the
instrument. It results in an uneven illumination of the image plane.
The effects of vignetting can be corrected using flat field images.
SBIG ST-i Manual
Appendix A – Connector and Cables
Telescope Jack
The Telescope Jack is used to provide tracking signals to the telescope drive. Viewed from outside the camera, looking in, it has the
following pin-out:
The Left, Down, Up and Right
signals are driven from optically isolated
photo transistors that
conduct when telescope movement
is desired. They can sink up to
25ma and can hold off up to 25V.
If what you are plugging into is
voltage based you’ll need an external pull-up resistor. The Common
signal is connected to the common on the four photo- transistors.
SBIG ST-i Manual
Appendix B – Camera Specifications
The table below lists the specifications for the ST-i camera. Specifications
are typical and can vary from camera to camera and are subject to change
without notice.
Pixel Array
Pixel Size
Full Well Capacity
Dark Current
A/D Converter
Read Noise
Binning Modes
Full Frame Download
USB 1.1
Power Requirements
Kodak KAI-0340
648 x 486
7.4 x 7.4 microns
23,500 electrons
~2e- at 25°C
Electromechanical and Electronic
0.001 to 3600 seconds, 10ms resolution
16-bit with Correlated Double Sampling
~9e- RMS
1x1, 2x2, 1xN, 2xN
Up to 1,800,000 pixels per second
Up to 400,000 pixels per second
USB powered
0.690 inches
1.25"D x 3.5"L
SBIG ST-i Manual
Appendix C – ST-i Color Camera Supplement
The raw single-shot color image:
The first thing you notice about the raw images from your single-shot color
camera is that they are not in color! This is normal - the color data is being
displayed as greyscale values in a raw single-shot color image You might
also notice a grid or “screen door” pattern covering the raw image as well.
This effect is also normal, and is caused by the RGB color mask that is
covering the CCD.
Single-Shot Color (SSC) cameras like the ST-i produce raw images that
CCDOps displays as monochrome until they are color processed. The
Color Process command in the Single Shot Color menu of the Utility menu
convents these raw images into color as shown in the dialog box shown
Note: Note that any adjustments made using the
controls in the “Contrast” dialog box ONLY
affect how image data is being displayed on
screen – you are not making any permanent
changes to your raw images.
You can perform the CCDOPS Dark Subtract,
Flat Field, Flip, Rotate and Crop functions on
single-shot color images, but do not use any of
the other Utility menu functions. These can make changes to the raw image
that will affect the final color balance. If you are using any other CCD
SBIG ST-i Manual
camera control software to acquire your single-shot color images, make sure
to save them in either SBIG or 16-bit FITS file format. You should not
crop, resize, or flip the image (using 3rd party software) before importing it
into CCDOPS for one-shot color processing.
Tip: CCDOPS will display a warning message if you try to perform any
processing steps that might affect the integrity of the color data
Care must also be taken when manually co-adding images to preserve the
color data - do not use the X and Y offset functions in the Co-Add dialog
box. Because a single-shot color camera uses a color mask placed directly
over the CCD surface, the software expects certain pixels to match up to
specific color positions on the mask. If the image has been cropped or
rotated (outside of CCDOPS) the software will no longer be able to
associate the pixels with the correct red, green or blue values. During
processing, this can cause an unusual color shift to appear. This situation is
most likely to occur if the raw image has been cropped or rotated before
CCDOPS is used for color combination. This alignment problem is also the
reason why precise registration of manually co-added images is so critical.
Make sure to save a copy of your raw images. If you make any mistakes or
want to re-process the image later on, you will always want to have the raw
image available to start over.
Easy Processing of Single-shot Color Images with CCDOPS
Once you have captured the image, save it with a pleasing contrast range
selection then, from the Utility drop-down menu in CCDOPS select Single
Shot Color --> Color Process and you are ready to go. Processing of
Single-Shot Color Camera images is easy. Start by clicking the Defaults
button and selecting RGB or DDP for the Method (DDP works great on
galaxies with bright cores). Click on “Process.” Now a full-color image
will finally appear! Experiment using the sliders to adjust the color balance,
brightness and contrast. Each time you click on “Process” the image will
update and display your changes. The single-shot color combination
methods available are:
RGB: Standard three channel (R, G, B) color combination (use the for best
results with planets)
DDP: Applies a DDP filter to each channel (R, G, B) before combination
(for deep sky objects) .
SBIG ST-i Manual
The image below is a screen captures of the single step process and the
dialog box shows the settings in their default positions using DDP as the
Step 1: Capture the image and save the raw data - it will appear
monochrome on the computer screen when first downloaded from the
Step 2: Click the "PROCESS" button to create the color image - this
step can be repeated without reloading the original image data - the
monochrome image will change to color.
If you don't like the color balance of the result, simply modify the color
balance pointers by making small changes and click the "process" button
again. For more in-depth color image processing, you can extract the RGB
color channels and perform more traditional tri-color image processing
techniques (see Processing Separate RGB Images, below).
SBIG ST-i Manual
Tip: While in the Single Shot Color Processing dialog box, click on any
slider, then use the keyboard right and left arrow keys to make fine
You can save the final color image as a TIFF file at any time by selecting
File -> Save As. Note that once the image is saved as a TIFF you won’t be
able to process it any further with CCDOPS. (You will still be able to open
and view the image, however.)
Color Balance
Any color image, even those from monochrome camera with external filter
wheels or from consumer digital cameras, may require minor corrections to
achieve the best color balance. This is done in CCDOPS by simply sliding
the Color Balance Sliders at the top of the dialog box. To make the image
more Red (or less Cyan) move the top slider towards Red then hit the
Process button again. If there's a star or an area of the image you know is
White you can White Balance on it by positioning the Crosshair over that
area, then right-clicking the mouse and select Set White Balance. It is a
very simple process. The color balance can be very sensitive to small
Brightness and Contrast
Use the Brightness and Contrast sliders to adjust the image and then hit the
Process button to see the results.
SBIG ST-i Manual
Images of galaxies tend to have a lot of dynamic range and you may find it
difficult to reveal the faint details in the arms without causing the core to
saturate. Try selecting the DDP instead of RGB in the "Method" drop down
box. Hit the Process button. DDP compresses the dynamic range of the
image. This may not look natural on all images but don't be afraid to try it.
An example is shown below.
RGB Processed
DDP Processed
The initial color processing doesn't have to be difficult or complicated.
Once you have saved the original B&W image you can experiment over and
over with different settings until you achieve the results you like. Of course,
if you want more control over the image you may wish to process the R,G
and B frames separately and combine them just as you would if the three
frames were taken separately though RG and B filters as they are with
monochrome cameras. See below for more about extracting, processing
and combining RGB frames.
Easy Processing of Separate R,G and B Images
Monochrome cameras with filter wheels are used to make color images by
shooting separate red, green and blue frames through color filters. Separate
Red, Green and Blue frames may also be extracted from a Single Shot
Color Camera image for more control during the processing stages.
Advanced users may desire the additional control this gives them over the
color processing steps. CCDOPS also offers you the option to extract
individual color channels from the raw frame.
If you want to follow along with this example, a copy of the M33 raw
image is available on the SBIG software CD-ROM in the Images folder.
SBIG ST-i Manual
To do this using CCDOPS select Utility --> Single Shot Color --> Extract
Color Channel(s)... The Color Extraction dialog box will open and give
you the option to extract any (or all) of the individual color channels (Red,
Green, Blue) and a synthesized Luminance (greyscale) channel:
Once extracted, the R,G and B frames from a Single Shot Color Camera are
treated the same as RGB frames shot with a monochrome camera and color
filter wheel. The individual color channels are extracted at full resolution
by interpolating the data from the neighboring pixels. Once the individual
color channel images are saved to disk, you can combine them using any
image processing software.
The RGB Combine dialog box will still remain open after the color image is
displayed, allowing you to adjust the color balance of the final image. Each
time you click on “Do It” the image will update and display your changes.
Select File -> Save As to save the final color image as a TIFF file.
Processing separate RGB images to create a color image involves the
following steps:
1. Co-aligning the images
2. Normalizing the Sky Background
3. Setting the White Balance.
CCDOps makes this relatively easy. Here's a step-by-step procedure for
quick and easy RGB Processing:
1. Co-align the images - Open the Red, Green and Blue images and then
open the Crosshairs.Visually identify a common star or feature in the
images to serve as an alignment reference. Starting with the Red image,
position the Crosshair on the reference position, using the peak pixel
brightness on a star for example, then right-click the mouse. Select the Set
RGB Red Position item to mark the reference position. Do the same in the
Green and Blue images, selecting the Set RGB Green Position and Set RGB
Blue Position respectively. This tells CCDOps how it will co-align the
SBIG ST-i Manual
2. Normalize the Sky Background - Normalizing the Sky Background
means making sure it comes out a neutral gray in the final image, not
having a subtle color tint. Bring the Red image to the foreground and then
position the Crosshair on an area of the image that represents the Sky
Background, free of any stars or faint nebulosity. Right-click the mouse and
select the Set RGB Black Level. This tells CCDOps how to normalize the
sky background.
3. Set the White
Balance - Again, bring
the Red image to the
foreground and then
position the Crosshair
over a star or area of the
image that you feel
represents the White
Balance. If you get it
wrong it's easy to adjust
so don't worry about it.
Once the Crosshair is
positioned, right-click
and select the Set RGB
White Level. This tells
CCDOps two things:
how to set the color
balance and how to set the contrast of the RGB image such that the star you
identified comes out white (neutral color) and just saturates in the RGB
image. Now that the hard work is done you can close the Red, Green and
Blue images and then invoke the RGB Combine command in the Utility
menu. You'll be shown the dialog at right. If the Advanced Setting section is
not visible, click the green triangle to reveal it. To finish the color
processing do the following:
4. Identify the images - Click the Set Name button to the right of the Red
and navigate through your folders on your hard drive to find the Red image.
Double-click the Red Image or select it and hit Open.
If you used CCDOps to acquire the images they will be named XXXX.r,
XXXX.g and XXXX.b and at this point CCDOps will fill in the names of
the Green and Blue images for you. If not then click the Set Name button to
the right of the Green and Blue and identify those images.
5. Initial RGB image - Click the “Do It” button to see the results of
merging the Red, Green and Blue images into a single RGB image. 6.
Tweak the parameters – [a] Co-alignment - Modify the Horizontal and
Vertical adjustments edit fields to the right of each image to tweak the coalignment. The easiest way to do this is to look at the outer fringes of stars
my zooming in on the RGB image. If the stars have a Red tint to the right
SBIG ST-i Manual
then you would reduce the Red Horizontal item by 1. After each adjustment
hit the “Do It” button to see the results. [b] Color Balance – Raise or lower
the Factors column to adjust the Color Balance. For example, to make the
image redder, raise the Red factor. Hit the Do It button to see the results. [c]
Brightness and Contrast - Raise or lower Grey Level item to adjust the
Brightness and raise or lower the Contrast Boost item to adjust the image
contrast. Hit the Do It button to see the results.
6. Exporting to Other Image Processing Programs - If you have a
favorite image processing program like PhotoShop that you would rather
use to process and combine the RGB frames into a color image, then simply
save the extracted R,G, and B images in a format of your choice such as
TIFF or FITS and use any other image processing program to manipulate
and combine the images. It is recommended however that you keep your
original data file in SBIG format in the event that some step along the way
results in an irreversible change to your image file(s) that is not to your
liking. You can always extract the raw RGB channels again from the
Special CCDOPS Functions for Single Shot Color Cameras
Filter Routines Specific to Single Shot Color Images
The raw images (monochrome, prior to conversion to color) from Single
Shot Color cameras like the ST-2000XCM require special handling when it
comes to filtering the images so that
you don't co-mingle the color data in
the filtering process. CCDOps has
enhanced filtering routines in the
Smooth, Sharpen, Column/Row
Repair, Kill Warm Pixels and
Remove Cool Pixels commands from
the Filter sub-menu of the Utility menu. As shown in the dialog below,
these commands allow you to check a Single Shot Color Image checkbox
that applies those enhancements to Single Shot Color images.
Track & Accumulate Single Shot Color Cameras
You didn’t used to be able to do this and many people don’t realize that
now you can use SBIG patented Track and Accumulate with Single Shot
Color (SSC) cameras like the ST-i. CCDOps has been updated to recognize
SSC cameras and Track and Accumulate will then make sure it co-aligns
images correctly, taking into account the Bayer filter arrangement.
SBIG ST-i Manual
Appendix D – Dimensions and Backfocus
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF