null  null
VBP5000
VIDEO IN A BAG SYSTEM WITH
5.6" LCD MONITOR VCP & DVD PLAYER
A. INTRODUCTION
Thank you for selecting the VBP5000 “Video in a Bag” System.
The system's main features include a 5.6" Liquid Crystal Display (LCD) Monitor Video Cassette Payer (VCP) and a DVD
Player. The VBP5000 utilizes state of the art electronics and is
designed for use in Vehicles, Hotels, the Office and Home. The
“Video in a Bag” System is constructed to provide years of reliable, trouble-free service. The system is compact so that you
can take it with you anywhere and is designed for quick and easy
installation. The LCD monitor is detachable and can be utilized
and stored separately from the main unit. Two additional monitors can be purchased and added to the system setup* allowing
you to utilize three monitors at once (two external and one attached). The connection of the additional monitor is plug and
play.
*NOTE: The AC Adaptor will only support Two Monitors.
Please read the entire instruction manual supplied with this product prior to operation. The documentation will assist you in installing the system properly to obtain the best equipment performance. All documentation should be stored for later use.
SAFETY PRECAUTION
For safety reasons, when changing video media, it is recommended
that the vehicle is not in motion, and that you do not allow children to
unfasten seat-belts to change video media or make any adjustments to the system. Enjoy your entertainment system but always
remember-safety of all passengers remains the number one priority.
IMPORTANT NOTICE
It is unlawful in most jurisdictions for a person to drive a motor
vehicle which is equipped with a television viewer or screen that is
located in the motor vehicle at any point forward of the back of the
driver’s seat, or that is visible, directly or indirectly, to the driver
while operating the vehicle. In the interest of safety, this system
should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle.
B. CAUTIONS AND WARNINGS
The Monitor is best kept in the fully closed position when it is attached to the VCP/DVD Player and not in use. Before putting on
headphones always adjust the volume setting to the lowest position. Do not apply pressure to the screen. Caution children to
avoid touching or scratching the screen, as it may become dirty or
damaged.
1. PLACEMENT
To prevent fire or electric shock, do not expose this appliance to
rain or moisture. Do not place the set on an unstable cart, stand,
bracket or table to prevent it from falling. Keep the unit away from
strong magnets, heat sources, direct sunlight, excessive dust.
If the unit is brought directly from a cold to a warm location, moisture may condense inside the unit. When you move it from a cold
to a warm location, wait for about one hour before operating the
unit, or remove the disc and leave the unit turned on until the moisture evaporates.
2. INSTALLATION
Ensure that the LCD Monitor, VCP, DVD Player, Bag and Pouch
are installed in accordance with the instructions and illustrations
provided in this manual. When the main unit is in the bag, ensure
the inside Velcro Strap of the bag is fastened to prevent the unit
from falling out of the bag (Refer to Figure 1). The “S” hooks and
all straps must be fastened correctly to secure the system in the
vehicle in the event of an accident. Operate the “Video in a Bag”
System with the bag open to ensure proper ventilation of the
VBP5000 system (Monitor/VCP/DVD Player). The system is intended to be mounted for rear seat viewing only. Do not use the
system in the front seat while operating your vehicle.
1
3. POWER
This system MUST be powered from the type of switched (Accessory) power indicated on the marking label (i.e. not directly from
the car battery). Power should be applied to the unit when the
ignition key is in the Run and/or Accessory positions. To prevent
battery discharge, disconnect the “Video in a Bag” System jack
from the cigarette lighter socket when the unit is not in use. Use
only the supplied power cable matching this set to avoid electric
hazards. Always disconnect the power source first and then the
jack from the system.
4. OBJECT AND LIQUID
Do not push objects of any kind into the system through openings;
do not spill or spray liquid of any kind on or in the system (this may
result in a fire or electric shock). Do not place anything heavy on
the unit. To ensure proper ventilation and proper operation, never
cover or block the slots and openings with a cloth or other material.
5. DISASSEMBLE
Do not attempt to disassemble the cabinet. There is a risk of electric shock and/or exposure to Laser Radiation. Contact qualified
service personnel if your system is in need of repair.
6. CLEANING UNIT
When cleaning, make sure the system is unplugged from the power
source. Do not use any solvents or cleaning materials (liquid, abrasive or aerosol) when cleaning the Video Monitor doing so may
scratch the screen. Use only a lightly dampened lint free cloth to
wipe the screen if it is dirty.
7. DISC
Do not use irregularly shaped discs such as heart or star-shaped
discs as they may cause the unit to malfunction.
Do not stick paper, tape or glue on the disc. Do not expose the disc
2
to direct sunlight or heat sources such as hot air ducts. Do not
touch the surface of disc. Handle the disc by its edge. Clean the
disc by wiping the disc from the center out with a cleaning cloth.
Remove the disc from the unit and store it in its case after playing.
Some playback operations of discs may be intentionally fixed by
software producers. Since this unit plays discs according to the
disc contents the software producers designed, some playback
features may not be available. Also refer to the instructions supplied with the discs.
8. VIDEO CASSETTE
Do not force a cassette into the compartment when the power
cord is unplugged. An inverted cassette cannot be inserted. After
playing a videocassette, remove it from the player. Store videocassettes in the sleeves or cases.
9. CLEANING VIDEO HEAD
To prevent video head clogging, use only good quality VHS tapes
and discard worn tapes. If the heads become dirty over a period of
time during normal operation of the VCP, the picture will be snowy
and the auto-tracking will not adjust the picture correctly. We recommend using cleaning cartridges sparingly to restore normal picture.
3
C. CONTENTS
1. 1 x Detachable Monitor & VCP & DVD Player Combo
2. 1 x DIN Cable
3. 1 x AC to DC Adapter
4. 1 x Cigarette Lighter Adapter
5. 1 x Remote Control with 2 AAA Batteries
6. 1 x Pouch
7. 1 x Mounting Bag with 4 Straps
8. 1 x Storage Bag
9. 1 x Instruction Manual
D. INDOOR PLACEMENT (IN A HOTEL, OFFICE, HOME, ETC)
To remove the VBP5000 from the protective mounting/storage
bag, place the open end of the unit face down on a flat surface.
Unfasten the Velcro Strap and pull it through the loop. Detach all
cables and slide the bag upward and off of the unit. Refer to
Figure 1.
VBP5000 Bottom View
Velcro Strap Bracket for Mounting Bag
Figure 1
a
b
d
c
Figure 2
4
e
f
Refer to the Figure 2. There are different ways to place the main unit,
monitor or combo on a table or other level surface. You can detach*
the monitor from the main unit by depressing the button below the
screen with one hand and removing the monitor with the other hand.
You can insert the monitor into the slot on the main unit with the screen
facing either front or back. Adjust the screen for the desired viewing
angle. The placement can be done with or without the unit inside its
mounting bag and pouch.
*NOTE: During the Removal and Reinstallation of the Video Monitor, rotate the monitor and the monitor’s hinged base so that they
are aligned in a straight line. The Video Monitor is inserted into the
slot on the main unit at a 45°.
Hinged
Base
45°
Figure 3
E. IN-CAR INSTALLATION
NOTE: When used in a vehicle, always keep the VBP5000 fastened
in the mounting bag.
1. BETWEEN TWO SEATS
Figure 4
5
a. Refer to Figure 4. Take one of the supplied straps from the
storage bag, and connect the latch to the upper side metal ring
on the left side of the mounting bag. Attach the "S" hook to the
same ring after looping the strap around the headrest of the
driver's seat. Repeat this process for the right side (Passenger
Seat).
b. Take another strap and connect the latch to lower metal ring on
the left side of the bag. Attach the "S" hook to the same ring after
looping the strap around the driver's seat rail. Repeat this process for the right side. In some vehicles, it may be necessary to
attach the "S" connector to the rail directly, as it may not be long
enough to reach back to the ring.
c. Adjust the straps tightly so that the mounting bag is secured.
d. Swing the monitor upwards and adjust the screen for the desired viewing angle.
*Optional
Second
Video
Monitor
Part #VBDV56
Figure 5
e. Refer to Figure 5. The monitor can be detached from the system by depressing the button below the screen with one hand
and removing the monitor with the other (Refer to Figure 3). Slide
the monitor into the monitor pouch, feed the bottom flap of the
pouch into the long slot of the monitor, and attach the Velcro
6
strap to fasten the monitor in the pouch. Then loop the strap of
the pouch around the headrest, and pull the loose end of the
strap while holding the buckle until the pouch is tightly secured.
f. If a second video monitor (optional) is used, remove the additional monitor and pouch from the storage bag, making sure to
feed the bottom piece of the pouch into the long slot of the monitor and attach the Velcro strap to fasten the monitor in the pouch.
Then loop the strap of the pouch around the headrest and pull
the end of the strap while holding the buckle until the pouch is
tightly secured.
g. Insert one end of the DIN cable into the MONITOR PORT on
the side of the detached monitor, and insert the other end into
the MONITOR PORT on the side of the main unit.
*Optional
Second
Video
Monitor
Part #VBDV56
Figure 6
h. Refer to Figure 6. You can contact an AUDIOVOX retailer for
additional monitor(S) Part #VBDV56, and insert it into the slot of the
main unit, or fasten it in the pouch onto the headrest, or just hold it
in your hand and connect it to the main unit with the DIN cable.
7
2. ON THE SEAT BACK (Refer to Figure 8)
Figure 7
a. Hang the bag onto the seat back by looping the shoulder strap
of the bag around the headrest of the seat.
b. Take one of the supplied straps from the storage bag, and connect the latch to the lower metal ring on the left side of the
mounting bag. Attach the "S" hook to the same ring after looping the strap around the seat rail. Repeat this process for the
right side. In some vehicles, it may be necessary to attach the
"S" connector to the rail directly, as it may not be long enough
to reach back to the ring.
c. Adjust the straps tightly so that the mounting bag is secured.
d. Swing the monitor upwards and adjust the screen for the
desired viewing angle.
8
3. On the Back Seat
a
b
Figure 8
a. The Monitor can be inserted into the slot with the screen facing
either front (refer to Figure 8a) or rear (refer to Figure 8b). Carefully place the system with the DVD facing up on the back seat.
Guide the vehicles safety belt through the short strap sewn on
the bottom of the mounting bag. Then secure and adjust the
safety belt so that the unit is not free to move around. Finally
uncover the attached monitor and adjust the screen for a desired viewing angle.
*Optional
Second
Video
Monitor
Part #VBDV56
Figure 9
9
b. Refer to Figure 9. The monitor can be detached from the system by depressing the button below the screen with one hand
and removing the monitor with the other (Refer to Figure 3). Slide
the monitor into the monitor pouch, feed the bottom piece of the
pouch into the long slot of the monitor, and attach the Velcro
strap to fasten the monitor in the pouch. Then loop the strap of
the pouch around the headrest, and pull the end of the strap
while holding the buckle until the pouch is tightly secured.
c. If a second video monitor (optional) is used, remove the
additional monitor and pouch from the storage bag, making
sure to feed the bottom piece of the pouch into the long slot of
the monitor and attach the Velcro strap to fasten the monitor in
the pouch. Then loop the strap of the pouch around the headrest and pull the end of the strap while holding the buckle until
the pouch is tightly secured.
d. Insert one end of the DIN cable into the MONITOR PORT on the
side of the detached monitor, and insert the other end into the
MONITOR PORT on the side of the main unit. Repeat this process if an optional second monitor is used (2nd DIN cable is
supplied with the optional monitor). Contact an Audiovox’s retailer for an additional monitor, and insert it into the slot of the
main unit, or fasten it in the pouch onto the headrest, or just hold
it in your hand and connect it to the main unit with the DIN cable.
10
F. POWER SUPPLY
1. Powering the system indoors (Refer to Figure 10)
Figure 10
Take the AC to DC adapter from the storage bag. Plug one end of
the AC to DC adapter into the DC 12V jack on the side of the main
unit, then plug the other end into the 110V AC power receptacle.
2. POWERING THE SYSTEM IN THE VEHICLE (Refer to Figure
11)
Figure 11
Take the cigarette lighter adapter from the storage bag. Plug one
end into the DC 12V jack on the side of the main unit, then plug the
other end into the cigarette lighter socket*.
*NOTE: Always disconnect the VBP5000 when not in use.
11
3. POWERING THE DETACHED MONITOR INDOORS (Refer to
Figure 12)
Figure 12
The monitor can be detached from the system by depressing the
button below the screen with one hand and removing the video
monitor* with the other hand.
*NOTE: During the Removal and Reinstallation of the Video Monitor, rotate the monitor and the monitor’s hinged base so that they
are aligned in a straight line. The Video Monitor is inserted into the
slot on the main unit at a 45° (refer to Figure 3 ).
Take the AC to DC adapter from the storage, plug one end into the
DC 12V jack on the side of the monitor, then plug the other end into
the 110V AC power receptacle.
4. POWERING THE DETACHED MONITOR IN THE VEHICLE (Refer to Figure 13)
Figure 13
12
Take the cigarette lighter adapter from the storage bag, plug one
end into the DC 12V jack on the side of the monitor, then plug the
other end into the cigarette lighter socket.
NOTE: When the monitor is combined with the main unit DC 12V
power will be supplied from the main unit to the monitor, so there is
no need for another power source to be connected to the DC 12V
jack on the side of the monitor.
*Optional Second
Video Monitor
Part #VBDV56
Figure 14
5. POWERING THE SYSTEM WITH MULTIPLE MONITORS
(Refer to Figure 14)
1) When the monitor is detached from the main unit, you can connect the PORT on the side of the monitor to either MONITOR 1
port or MONITOR 2 port on the side of the main unit with the supplied DIN cable. When the monitor is connected to the main unit
with the DIN cable, DC 12V power, Audio/Video and IR signals will
all be supplied through the DIN cable to the connected monitor. So
there is no need for another power source to be connected to the
DC 12V jack on the right side of the detached monitor. In this situation, the AC to DC adapter can drive only two monitors either combined with the main unit or connected to the main unit with the DIN
cable.
13
2) Refer to Figure 15. In the vehicle, the cigarette lighter adapter
can drive up to 3 monitors combined with the main unit and connected to the main unit with the DIN cable.
*Optional
Video
Monitors
Figure 15
14
G. CONTROLS, INDICATORS, AND CONNECTORS
1. UNIT VIEW (Refer to Figure 16)
MONITOR RIGHT SIDE
1) Brightness UP/DOWN Thumbwheel
2) Volume UP/DOWN Thumbwheel
3) Headphone Input # 2
4) Headphone Input # 1
MAIN UNIT
5) REMOTE CONTROL SENSOR
6) MAIN POWER
7) VCP STOP/EJECT Button
8) VCP REWIND Button
9) VCP PLAY Button
10) VCP FAST FORWARD Button
11) DVD/AV and VCP SELECT Switch
12) DVD OPEN Button
13) DVD STOP Button
14) DVD PREVIOUS Button
15) DVD PLAY Button
16) DVD NEXT Button
MONITOR LEFT SIDE
17) POWER ON/OFF BUTTON (Monitor)
18) RIGHT AUDIO IN (Monitor)
19) LEFT AUDIO IN (Monitor)
20) VIDEO IN (Monitor)
21) MONITOR JACK (Input)
22) DC 12V INPUT (Monitor)
MAIN UNIT BOTTOM
23) DVD/AV OUTPUT
24) MONITOR PORT #1 (Output)
25) VCP A/V OUTPUT
26) MONITOR PORT #2 (Output)
27) DC 12V INPUT
28) A/V INPUT
Right Side
Front
Left Side
Bottom Right
Figure 16
15
2. REMOTE CONTROL VIEW (Refer to Figure 17)
1) POWER Button
2) DISPLAY Button
3) DVD ANGLE Button
4) DVD SUBTITLE Button
5) DVD AUDIO Button
6) DVD ZOOM Button
7) DVD UP/DOWN/LEFT/RIGHT/
ENTER Buttons
8) DVD MENU Button
9) DVD Return Button
10) DVD A-B Button
11) DVD NEXT Button
12) DVD PREVIOUS Button
13) DVD REVERSE Button
14) DVD FORWARD Button
15) VCP EJECT Button *
16) VCP POWER Button
17) VCP PAUSE Button
18) VCP STOP Button
19) DVD NUMBER Button
20) DVD SETUP Button
21) DVD REPEAT Button
22) DVD PAUSE Button
23) DVD PLAY Button
24) DVD STOP Button
25) DVD SLOW Button
26) VCP PLAY Button
27) VCP FAST FORWARD Button
28) VCP REWIND Button
Figure 17
*NOTE: To Eject a tape with the Remote Control, you must
press the Stop button first.
16
H. PLAYING A DVD
After connecting power to the unit, momentarily press the ‘Power’
button on the Main Unit, then press the ‘Power’ button on the side of
the Monitor. Press the ‘OPEN’ button on the Main unit to open the
DVD Player, insert a disc and close the DVD Player. The system will
start playing automatically. If the ‘POWER’ button is pressed ‘ON’
when there is already a disc in the unit, the system will automatically
start playback of the disc.
1. BASIC DVD OPERATION
POWER................. Turns the Main Unit ON and OFF
DVD/AUX/VCP... Selects either DVD, AUX or VCP Playback
OPEN.................... Opens the DVD Cover
PLAY..................... Starts Playback
SLOW................... Plays DVD at 1/2, 1/4, or 1/8 Times the Normal Playback Speed
PAUSE.................. Still Picture
STOP.................... (1 time) Stops Playback and will resume at the
Present Playback Point when the PLAY button is
pressed again
(2 times) Stops Playback and returns to the beginning
NEXT..................... Advances to the Next Chapter, Track or Scene during
playback
PREVIOUS........ Goes back to the preceding chapter, track or
scene during play back
FORWARD......... Scans Forward at 2, 4, 6, or 8 times Normal Speed
REVERSE.......... Scan Backward at 2, 4, 6, or 8 times Normal Speed
UP/DOWN/
LEFT/RIGHT...... Used for Menu Navigation
ENTER.............. Execute an Item or Setting
NUMBERS......... Select an Item or Setting
RETURN............ Return to the previous selection
MENU..................... Display the Root Menu of the disc
REPEAT............. Repeat Playback of a Title or Chapter
A-B.................... Repeat a specific portion from point A to point B
of the disc
DISPLAY............ Display information (Title, Chapter, Track, Time, etc.)
ANGLE.................... Change the Angles on the scene (if available)
SUBTITLE.......... Selects the Subtitle Language and turns it ON/OFF
AUDIO............... Select the Audio Language
ZOOM...................... Enlarge an Image to 1.5, 2, or 4 times the original
SETUP..................... Display the Setup Menu to select and set items and
exit the setup menu
17
2. MENU
A DVD is divided into sections called titles and chapters. When
you play a DVD, a root menu of the disc will appear on the screen
of your TV or Monitor. The contents of the menu vary from disc to
disc. Press MENU during playing to display the menu, and press
ENTER or PLAY to start playing. Some DVDs only allow you to
select disc playback options using the DVD menu.
3. DISPLAY (Display contents vary from disc to disc.)
1) PLAYING TIME AND REMAINING TIME
a. During playback press ‘DISPLAY’ to display the current Title
Number (1), the total Number of Titles (2), the current Chapter
Number (3), the total Number of Chapters (4), and the Playing
Time for the title (5). The heading will disappear automatically
after 3 seconds if no buttons are pressed.
Title, Chapter Number, and Time Screen Display
b. Press ‘DISPLAY’ again to display the Remaining Time of the
title. The heading will disappear automatically in about 3
seconds.
Title Remaining Time Screen Display
18
c. Press ‘DISPLAY’ the 3rd time to display the Elapsed Time for
the chapter. The heading will disappear automatically in about
3 seconds.
Chapter Elapsed Time Screen Display
d. Press ‘DISPLAY’ the 4th time to display the Remaining Time
for the chapter. The heading will disappear automatically after
3 seconds. Press ‘DISPLAY’ a 5th time to exit.
Chapter Remaining Time Screen Display
2) ANGLE
During playback of a disc, press ‘ANGLE’ to display the available
angles for discs containing multi-angles*, with the current angle
number (1) and the total number of angles (2) displaying. Press
‘ANGLE’ to select another angle, then press again to exit and
return to the normal viewing angle. The angle display will disappear automatically if the ‘ANGLE’ button is not pressed again
within 3 seconds.
*NOTE: Not all discs contain this feature
19
Angle Screen Display
3) SUBTITLE
During disc playback press ‘SUBTITLE’ to select the subtitle language you desire, with the current Subtitle Language Number
(1) and the total Number of Subtitle Languages (2) displayed. If
there are multiple languages press ‘SUBTITLE’ again to select
another subtitle language. To turn subtitles OFF, press the ‘SUBTITLE’ button until ‘SUBTITLE OFF’ is displayed. The Subtitle
display will disappear automatically if the ‘SUBTITLE’ button is
not pressed again within 3 seconds.
Subtitle Screen Display
20
4) AUDIO
During playback press ‘AUDIO’ to select the audio language you
desire, with the current Audio Channel Number (1) and the total
number of Audio Channels (2) displayed. Press AUDIO again to
select another audio language. The audio display will disappear
automatically if the ‘AUDIO’ button is not pressed again for 3
seconds.
Audio Language Screen Display
5) ZOOM
During playback press ‘ZOOM’ to enlarge the picture by 1.5, 2,
or 4X with the current zoom multiple (1) displaying. Press ‘UP/
DOWN/LEFT/RIGHT’ to move the picture. Press ‘ZOOM’ again
to select another zoom multiple or until ZOOM OFF is displayed
and the picture will return to normal size. The zoom display will
disappear automatically if the ‘ZOOM’ button is not pressed within
3 seconds.
ZOOM Screen Display
21
6) A-B REPEAT
a. During playback press ‘A-B’ to set the Starting Point A.
A - B Repeat Starting Point Screen Display
b. Press ‘A-B’ to set the Ending Point B and the player will repeatedly play the part between Point A and Point B.
A - B Repeat Ending Point Screen Display
c. Press ‘A-B’ a 3rd time to Cancel A-B Repeat. Normal play
back will resume from Point A.
A-B Repeat Cancelled Screen Display
22
7) REPEAT
a. During playback press ‘REPEAT’ once to repeatedly play the
current chapter.
Chapter Repeat ON Screen Display
b. During playback press’ REPEAT ‘again to repeatedly play the
current title.
Title Repeat ON Screen Display
c. During playback press’ REPEAT’ a 3rd time to cancel the repeat playback function and resume normal play back. The
repeat display will disappear automatically if the ‘REPEAT’
button is not pressed again for 3 seconds.
Repeat OFF Screen Display
23
4. PLAYING AUDIO CDS
When playing an audio CD, the DISPLAY Banner appears
automatically. It displays the current track and the amount of the
time for that track playing, the total amount of time on the disc and
the current time running on the disc. Press the DISPLAY button on
the remote to display the DISPLAY Banner. The options below show
you what happens when you press the DISPLAY button.
a. During playback press ‘DISPLAY’ once and SINGLE
ELAPSED will appear along with the current track
playing and the time of that track.
SINGLE ELAPSED
00:00:00
01/02
SINGLE ELAPSED Screen Display
b. Press ‘DISPLAY ‘2 twice and SINGLE REMAIN appears
along with the current track playing the and the amount
of time left.
SINGLE REMAIN
00:00:00
01/02
SINGLE REMAIN Screen Display
24
c. Press ‘DISPLAY’ three times and TOTAL ELAPSED
appears along with the current track playing the total
time playing on the CD.
TOTAL ELAPSED
00:00:00
01/02
TOTAL ELAPSED Screen Display
d. Press ‘DISPLAY’ four times and TOTAL REMAIN appears
along with the current track playing and the amount of time
left on the CD.
TOTAL REMAIN
00:00:00
01/02
TOTAL REMAIN Screen Display
e. Press ‘DISPLAY’ a fifth times and “OFF” will appear
momentarily then disappear. CD Time Information will not be
displayed.
1) USING THE REPEAT FEATURE
The default mode for the Repeat feature is OFF. Pressing REPEAT
consecutively changes the repeat options:
•
REP-ONE- repeats the track that is playing.
•
REP-ALL- repeats the disc that is playing.
•
REPEAT OFF
As you toggle through the options, the repeat option changes. The
selected repeat option loops repeatedly until you turn it off.
25
5. PLAYING MP3 DISCS
MP3 is a format for storing digital audio. An audio CD-quality
song can be compressed into the MP3 format with very little
loss of quality, while taking up much less space. CD-R discs
that have been encoded in MP3 format can be played on your
DVD player.
SELECTING FOLDERS AND SONGS
When an MP3 disc is inserted in the player, the SMART NAV
screen will appear automatically. The SMART NAV screen
is used to change folders and songs as well as display Disc
TIME and TITLE Information. Songs are played in order they
were saved on to the disc.
1. Once the Disc is loaded and is playing, press ‘STOP’ then
press either the UP or DOWN arrow buttons on the
Remote Control to navigate through the folder list on the
right side of the SMART NAV screen.
2. Once the folder you want is highlighted, press ‘ENTER’
(the folder list shifts to the left side of the screen and the
songs in the folder appear on the right).
..
MP3
MP3
MP3
MP3
MP3
SMART NAV Screen Display
3. Press the UP or DOWN Arrow buttons on the Remote
Control to navigate through the song list and highlight the
song you want. Press ‘ENTER’ to begin playback of that
song.
SKIPPING SONGS
Use the Next ( uu ) button on the remote control to move to
the next song. Use the Previous ( tt) button to move to the
beginning of the currently playing song. Press the button
again to move to the previous song.
26
3) USING THE REPEAT FEATURE
The default mode for the Repeat feature is OFF. Pressing
REPEAT consecutively changes the repeat options:
• REP-ONE- repeats the songs that is playing.
•
FOLDER REP- repeats the folder that is playing.
•
FOLDER- turns off repeat and returns to regular play
mode.
4) SELECTING A PLAY MODE
You can choose what order the songs will play on a disc
temporarily. The FOLDER play mode is the default. To access
the play mode options, press STOP if the disc is playing.
Press the right arrow button until the PLAY MODE option is
highlighted. Use the up or down arrow to choose an option.
The play mode options are:
• SINGLE: Play a selected song.
•
REP_ONE: Repeats the song that is playing.
•
FOLDER: Plays the folder in the order the songs were
recorded.
•
FOLDER REP: Repeats the folder that is playing.
•
DISC SCAN: Plays the first ten seconds of each song on
the disc. When the desired track is heard, press play to
begin play of the track.
•
DISC: Plays the entire disc.
•
DISC REP: Repeats playback of the entire disc.
•
RANDOM: Plays the songs on the entire disc in random
order.
•
SHUFFLE ON: Plays the songs in random order (from
within the selected folder)
•
PROGRAM PO: Plays the songs on the disc in the order
you have programmed (you must create a playlist to set
the order you want the tracks on the disc to play). When
you are creating a playlist, this option changes to
PROGRAM.
27
5) PROGRAM PLAY
To use the program play option, you must create a playlist
of songs in the order you want them to play.
Note: Once you begin adding songs from a folder to
create your play list, you cannot add songs from a
different folder.
a)
Choose the PROG-PO option from the PLAY MODE
then press Enter to change the option to PROGRAM.
b)
Add songs to the program list by highlighting the song
you want to program and pressing ENTER once the
song is highlighted. The song you have chosen and the
number of songs you have chosen appear at the top of
the screen. For example, if you choose the number five
song within the folder and it is the first song you have
chosen, PROGRAM P01:05 appears.
c) You can continue to add songs to the list from within the
same folder by using the up or down arrow button and
then pressing ENTER to add it to the list.
d) When you are done creating the list, press STOP to end
the programming, PROG END will be displayed. Then
press PLAY to begin the program play mode.
6) DELETING THE PLAYLIST
To delete the entire playlist, press STOP while the disc is playing
and change to another play mode.
7) DISPLAYING THE TIME ELAPSED AND TIME
REMAINING
Press the ‘DISPLAY’ button on the remote to display disc
information. The options below show you what happens when
you press the ‘DISPLAY’ button.
28
a)
Press ‘DISPLAY’ once, and “TIME ELAPSED” will appear
along with the amount of time the song has been playing.
“TIME ELAPSED” and the of actual amount of time the
disc has been playing, will be displayed on-screen until
you press DISPLAY again.
TIME ELAPSED
00 : 01 : 32
..
MP3
MP3
MP3
MP3
MP3
TIME ELAPSED Screen Display
b)
Press ‘DISPLAY’ a Second time and TIME REMAIN will
appear along with the amount of time left in the song that
is playing. TIME REMAIN and the amount of time
remaining will be displayed on-screen until you press
DISPLAY again.
TIME REMAIN
00 : 01 : 32
..
MP3
MP3
MP3
MP3
MP3
TIME REMAIN Screen Display
c)
Press ‘DISPLAY’ a Third time and “OFF” will appear
momentarily then disappear. CD Time Information will not
be displayed.
29
6. SETUP (The contents vary from disc to disc.)
Press ‘SETUP ‘to display the Main screen of the SETUP Menu on
the screen. Press ‘SETUP ‘again to exit the SETUP Menu and
the unit will resume it’s last playback or stop mode.
Main SETUP Menu Screen
1) Select ‘GENERAL SETUP’ using the UP/DOWN buttons, then
press ‘ENTER’ to enter the GENERAL Setup screen.
General SETUP Menu Screen
a. Select TV DISPLAY using UP/DOWN, and then press RIGHT
to enter the submenu. Select the TV display mode on the
screen using UP/DOWN, and press ENTER to confirm the
setting. Press LEFT to return.
* NORMAL/PS: When the player is connected to a normal
TV, and a wide picture is shown on the full screen.
* NORMAL/LB: When the player is connected to a normal TV,
and a wide picture is shown on the screen, with black strip at
both top and bottom of the screen.
30
* WIDE: When the player is connected to a wide screen TV, a
wide picture is shown on the full screen.
b. Select ‘ANGLE MARK’ using UP/DOWN, and then press
the RIGHT button to enter the submenu. Choose Angle Mark
on or off displayed on the screen using the UP/DOWN and
then press ENTER to confirm the setting. Press the LEFT
button to return.
ANGLE MARK Screen Display
* ON: The screen will show angle mark. (If angle option is
available)
* OFF: The screen will not display the Angle Mark.
c. Select ‘MAIN PAGE’ using UP/DOWN, and then press ENTER
to return to the main page.
MAIN PAGE Screen Display
31
2) When there’s no disc inside the player, select ‘PREFERENCES’
using UP/DOWN, and then press ‘ENTER’ to enter the preferences page.
AUDIO Preference Screen Display
a. Select ‘AUDIO’ using UP/DOWN, and then press ‘RIGHT’ to
enter the submenu. Select the audio language you desire using
UP/DOWN, and then press ‘ENTER’ to confirm the setting.
Press LEFT to return.
b. Select ‘SUBTITLE’ using UP/DOWN, and then press RIGHT
to enter the submenu. Select the desired subtitle language or
SUBTITLE OFF using UP/DOWN, and then press ‘ENTER’
to confirm the setting. Press ‘LEFT’ to return.
SUBTITLE Preference Screen Display
32
c. Select ‘DISC MENU’ using UP/DOWN, and then press ‘RIGHT’
to enter the submenu. Select the Disc Menu Language you
desire using UP/DOWN, then press ‘ENTER’ to confirm the
setting. Press ‘LEFT’ to return.
DISC MENU Preference Screen Display
Note: Language and subtitle selection is only available for discs
that are recorded in the above listed languages. If not, the player
will play and display on the screen the original recorded language
contained in the disc.
d. Select ‘PARENTAL’ using UP/DOWN, and then press RIGHT
to enter the submenu.
PARENTAL Preference Screen Display
Select the parental level you desired using UP/DOWN for discs
with lock-out function or multiple rating levels. It’s listed from
the lowest level (1 Child) to the highest level (8 Adult). Press
‘ENTER’ to enter the Password Verify Page.
33
PASSWORD VERIFY Input Screen Display
Enter a 4 digit password, then press ‘ENTER’ to confirm the
parental level setting.
NOTE: For 1st time use, the default password 3308.
e. Select ‘PASSWORD’ using UP/DOWN, and then press RIGHT
to enter the submenu.
PASSWORD CHANGE Screen Display
Press ‘ENTER’ to enter the Password Change Page. Input
the Old Password or the Default Password, the New Password, and the Confirmed New Password. Press ‘ENTER’ to
confirm the change.
PASSWORD CHANGE PAGE Screen Display
34
NOTE: The Default Password is 3308. This password is always effective even after you have selected your own password and changed it. To avoid others from using the default
password to set the parental level and change the password,
you can record this default password in another area and delete
it from this manual. Some discs can be limited depending on the
age of users while some discs can not.
f. Select ‘DEFAULTS’ using UP/DOWN, and then press RIGHT
to enter the submenu. Press ENTER to make the setting re
turn to the factory-set mode.
DEFAULT PRESET Screen Display
g. Select ‘MAIN PAGE’ using UP/DOWN, and then press ENTER
to return to the main page. Press SETUP to exit the MAIN
PAGE
PREFERENCE MAIN Page Screen Display
35
I. BASIC VIDEO CASSETTE OPERATION
Power
DVD/AUX/VCP
Play
Stop/Eject
Rewind
Forward
(Fast)
Turn the unit ON/OFF
Choose the VCP mode
To playback tape
To stop tape (press once), to eject tape (press
twice)
a. Press it once in the playback mode, the VCP
enters the reverse picture search mode and the
tape will rewind rapidly with Video, the rewind indicator lamp will blink. Press it once more, and the
tape will rewind scan at a high speed with the lamp
blinking more quickly.
b. Press it in the stop mode, the tape will rewind at
a very high speed without any picture or sound.
a. Press it once in the playback mode, the VCP
enters the forward picture search mode and the
tape advances rapidly with video, the fast forward
indicator lamp will blink. Press it once more, and
the tape will advance at a high speed with the lamp
blinking more quickly.
b. Press it in the stop mode, the tape will advance
at a very high speed without picture or sound.
36
J. PLAYING A VIDEO GAME (Refer to Figure 18)
**Games
Not Included
*** Optional
Headphones
**Games
Not Included
*Optional
Video
Monitors
Figure 18
1. Plug the video output from your game system into the yellow video
jack and the Audio L and Audio R into the applicable jacks on the side
of the main unit, which takes priority over the built-in DVD player.
Adjust the volume control and the brightness control on the monitor
for individual preference.
2. Plug the video output from your game system into the yellow
VIDEO jack and the AUDIO L and AUDIO R into the applicable jacks
on the side of the monitor, which takes priority over both AV input into
the main unit and the built-in DVD player. Adjust the volume control
and the brightness control on the monitor for individual preference.
37
K. WIRED HEADPHONES (Refer to Figure 18)
Optional wired headphones may be used with the "Video In a Bag"
System. Simply plug in the headset to either HEADPHONE 1 jack or
HEADPHONE 2 jack on the left side of the monitor.
Note: Using HEADPHONE 1 jack will disconnect the internal speakers.
L. SUPPORT EXTERNAL MONITORS
1. Using MONITOR PORT (Refer to Figure 18 & 19)
Besides the monitor combined with the main unit, this system can
drive up to 2 additional monitors (Please contact an Audiovox dealer
for the additional monitors part # VBDV56) by using the cigarette
lighter adapter in the vehicle. (NOTE: The AC to DC adapter can
drive only 1 main unit and 2 monitors, either combined or detached).
Connect the PORT on the additional monitor to either MONITOR 1
port or MONITOR 2 port on the left side of the main unit with the
supplied DIN cable. After plugging in the main unit, DC 12V power,
Audio/Video and IR signals will all be supplied through DIN cable to
the additional monitor.
*Optional
Second
Video
Monitor
Figure 19
38
2. Using VIDEO, AUDIO L, AUDIO R outputs for connection
to any monitor
(Refer to Figure 18)
Match the color-coded plugs to the appropriate DVD OUT jacks or
VCP OUT jacks on the side of the main unit: Yellow (VIDEO) to
Yellow, White (AUDIO L) to White, and Red (AUDIO R) to Red.
M. SPECIFICATION
Color system: NTSC
Screen size: 5.6”
Disc format: DVD/CD/MP3
DVD video format: Horizontal 720 pixel, vertical 480 pixel (NTSC)
Frequency response: DVD (PCM 96 kHz/24 bits ): 20 Hz to 44 kHz
DVD (PCM 48 kHz): 20 Hz to 22 kHz
CD: 20 Hz to 20 kHz
Tape Width: 12.7mm
Tape Speed SP: 33.35 mm/s
Tape Playback Time: 180 minutes with T-180 set to the SP mode
(Fast)Forward/Fewind: Less than 7 minutes with T-120
Audio Track: 1 track
Audio output: 2 x 2 W
Audio S/N: Better than 35 dB
Video output: 1.0 Vp-p/75 Ohm, unbalanced
Video S/N: Better than 35 dB
Power source: DC 11 V to 16 V
Power consumption: 35 W (Main With Monitor)
Operating temperature: 5~40°C (41~104°F)
Storage temperature: -20~60°C (4~140°F)
Operating humidity: 10~75%
Dimensions (W x H x D): 250 x 263 x 135 mm ( 9.8” x 10.4” x 5.3”)
39
90 DAY LIMITED WARRANTY
Applies to Audiovox Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of
this product that should this product or any part thereof, under normal use and conditions, be
proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company’s
option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s),
transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to
correction of antenna problems, to costs incurred for installation, removal or reinstallation of
the product, or to damage to tapes, discs, speakers, accessories, or electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident,
or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF
THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO
THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF
15 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damage so the above limitations or exclusions may not
apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
U.S.A. : AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD.,
HAUPPAUGE, NEW YORK 11788 1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION
SERVING YOUR AREA
128-5556C
For Customer Service
Visit Our Website At
WWW.audiovox.com
Product Information, Photos,
FAQ’s Owner’s Manuals
© 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
128-6647
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement