CHDMI-42E Manual - HY-LINE

CHDMI-42E Manual - HY-LINE
4-in 2-out
HDMI Switcher
Operation Manual
CHDMI-42E
Introduction
CHDMI-42E is a high performance 4-input dual outputs HDMI switcher
with remote control. It allows your to connect up to 4 HDMI Sources so they can
share two HDMI displays. The two HDMI outputs are identical.
Simply pressing one button you can select your desired HDMI source
for display on two HDMI TVs simutaneously.
Features
* HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant.
* Signal Enhancement feature allows you to improve signal quality
after long distance transmission.
* LED indicators.
* Ideal for home theater integration, conference room and retail stores.
* Supports high resolution input:
PC: VGA, SVGA, XGA, SXGA, and UXGA (1600 x 1200)&
HDTV: 480i, 576i, 480p, 576p, 720p, 1080i, and 1080p
* Remote control.
* Easy to install and to operate.
Operation Controls and Functions
Front Panel
1
2
3
CHDMI-42E
Dual Output HDMI Switcher
4
INPUT
POWER
SIGNAL ENHANCE
1
2
3
4
1. Remote control sensor.
2. Input select/Indicators: Press the " INPUT" button repeatedly to switch to your
desired input source and the LED will illuminate to indicate which
input source is being selected.
3. Signal Enhancement/Indicator: Press the " Signal Enhance" button to turn
on this feature to improve signal quality after long distance transmission.
Press again to turn off. The LED will illuminate when the signal is enhanced.
4. POWER Switch/Indicator: Press the "POWER" button to turn on/off the power,
the power LED illuminate in red color means the power is turned on, when
the LED not illuminate power is turned off.
Operation Controls and Functions
Rear Panel
RS-232
DC 5V
OUTPUT 2
OUTPUT 1
INPUT 4
INPUT 3
INPUT 2
INPUT 1
2
3
1
4
1. HDMI outputs: Connect each HDMI output to the HDMI input of
your displays using HDMI cable. The two HDMI outputs are identical.
2. HDMI inputs: Connect your various HDMI sources to each of the
HDMI input of the unit using HDMI cables.
3. Power: Plug the supplied 5VDC power supply into the unit.
4. RS232: 9-pin D-sub female connector for connecting to your other control
console for remote control.
RS-232 Remote Control Protocol
The connection between CHDMI-42E and remote pc through RS-232 modem cable.
* Command:
Pins definition of
modem cable
PIN Definition
Remote Controller
PIN
Definition
1
NC
2
RxD
3
TxD
4
NC
5
GND
1
NC
2
TxD
3
RxD
4
NC
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC

Command Code
Comment
"I" + "1"
PORT 1 ON
"I" + "2"
PORT 2 ON
"I" + "3"
PORT 3 ON
"I" + "4"
PORT 4 ON
"S" + "1"
ENABLE SIGNAL ENHANCE
"S" + "0"
ENABLE SIGNAL ENHANCE
"P" + "1"
POWER ON
"P" + "0"
POWER OFF

* RS-232 transmission format:
Baud Rate: 9600 bps
Data Bit : 8 bits
Parity
: None
Stop Bit : 1 bit
1
2
Remote Control
1. Power:
Press the button to turn on/off the unit.
2. Direct input selector:
Press numerical number button to select your desired
input source.
3. Void buttons (No function). If the button number is
greater than the total input number of the unit then
the button is of no function.
3
CR-22
Specifications
* Frequency Bandwidth: 1.65Gbps(single link)
* Inputs: 4 x HDMI female ports (Type A connector)
* Outputs: 2 x HDMI female port (Type A connector)
* 5VDC universal power supply
* Weight(g): 800
* Dimension(mm): 240(W) x104(L) x 48(H)
Connection and Installation
RS-232
DC 5V
OUTPUT 2
OUTPUT 1
INPUT 4
INPUT 3
DVD 3
DVD 1
DVD 2
LCD TV
LCD TV
INPUT 2
INPUT 1
STB
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement