- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- Crestron
- SWAMPE-8
- User guide
advertisement
Crestron SWAMP(I)E-8
Sonnex ® Multiroom Audio Expander,
8 Zone
Operations Guide
Important Safety Instructions
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• Disconnect power prior to connecting or disconnecting equipment.
• Do not install in direct sunlight.
• The apparatus must be installed in a way that the power cord can be removed either from the wall outlet or from the device itself in order to disconnect the mains power.
• Prevent foreign objects from entering the device.
TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE
COVER. THERE ARE NO USER SERVICEABLE PARTS
INSIDE. ONLY QUALIFIED SERVICE PERSONNEL
SHOULD PERFORM SERVICE.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING. OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED
ON THE APPARATUS.
WARNING:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure t hat may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
THIS IS AN APPARATUS WITH CLASS I
CONSTRUCTION. IT SHALL BE CONNECTED TO AN
ELECTRICAL OUTLET WITH AN EARTHING GROUND
TERMINAL.
IMPORTANT:
These devices can be used with Class 2 output wiring.
.
Regulatory Compliance
These products conform to UL 60065; certified to CSA C22.2 No. 60065.03.
As of the date of manufacture, the SWAMPE-8 and SWAMPIE-8 have been tested and found to comply with specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specific patents that cover Crestron products are listed at patents.crestron.com
.
Crestron, the Crestron logo, AIR, Aspire, Cresnet, Essence, Excite, Saros, Sonnex, Sonnex Speaker Protect, and SSP are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Blu-ray Disc is either a trademark or registered trademark of the
Blu-ray Disc Association (BDA) in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Contents
Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 1
Operations Guide – DOC. 7051D Contents • i
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Sonnex Multiroom Audio
Expander, 8 Zone: SWAMP(I)E-8
Introduction
Operations Guide – DOC. 7051D
The SWAMPE-8 is an 8-zone expander for the Sonnex
(SWAMP-24X8)* from Crestron ®
® Multiroom Audio System
. It adds eight stereo amplified zones to the
Sonnex system, with the option for installation at the central equipment rack or at a remote location near the rooms it serves. The latter “decentralized” approach has the benefit of minimizing the amount of speaker wiring required, affording higher performance and efficiency and a faster, easier, and less expensive installation.
The SWAMPE-8 and SWAMPIE-8 are functionally identical. For simplicity within this guide, the term “SWAMPE-8” is used except where noted.
Features and Functions
• Eight-zone Sonnex expansion with amplified outputs
• 140 watts/channel @ 8 ohms, 400 watts/channel bridged
• 70/100 volt “constant-voltage” output options available
• Advanced DSP, mono summing, and output bussing per zone
• Sonnex Speaker Protect™
• Individual zone power control and global standby
• Remote fault monitoring
• Heavy duty detachable terminal blocks
• Single-cable interface to SWAMP-24X8 via Sonnex Link
• Plug-and-play operation
• Low power consumption, cool-running operation
• Three-space rack mountable
Integrated Audiophile Amplifier
The SWAMPE-8 features the same custom hybrid amplifier design as the
SWAMP-24X8, delivering the warmth and neutrality of a fine Class AB amplifier with all the efficiency benefits of a modern Class D. Each of its 16 channels
(configured as eight stereo zones) delivers 140 watts into 8 ohms or 240 watts into 4 ohms, and any two adjacent outputs can be bridged to produce 400 watts per channel at 8 ohms. Even with such incredible power, the SWAMPE-8 runs cooly and efficiently and requires only three rack spaces for mounting. Each zone is individually controllable to save energy by turning off any unused channels.
* Sold separately.
Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 1
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Digital Signal Processing
Each zone features independent DSP for optimal sound quality and control in every room. Sonnex DSP capabilities include graphic or parametric 5-band EQ, dynamic range control, volume, bass, treble, balance, loudness, mute, mono summing, and five selectable tone profiles. For passive subwoofer applications, a choice of second or fourth order active crossover filters can be set using the parametric EQ, leaving the four remaining EQ filters available for room correction and tonal enhancement.
Output Bussing
Output bussing allows multiple zones to function as one, whether fed from the
SWAMPE-8, the SWAMP-24X8, or another Sonnex Expander. Output bussing is ideal for grouping adjacent listening areas together or associating a subwoofer with its stereo speaker pair. Volume offset adjustments allow for balancing the levels of each bussed zone for smooth, even coverage.
70/100V Option
Any zone output can be converted to 70 or 100 volt output using one or more Sonnex
Output Transformers (SAT-70V/100V-2 or SAT-70V/100V-4 1 ). Also known as
“constant-voltage”, 70 volt and 100 volt speaker systems allow for long wire runs using small-gauge wire, with the potential for connecting numerous speakers per circuit. Typical applications include outdoor speaker zones, commercial retail spaces, hallways, and common areas.
Simple, Versatile Installation
The SWAMPE-8 can be installed along with the SWAMP-24X8 at the central equipment rack or separately at a remote location. It interfaces with the
SWAMP-24X8 via a single CAT5e shielded twisted pair (STP) cable up to 200 ft
(61 m) in length.
2 This length can be increased to 2000 ft (610 m) using multimode fiber optic cable with the S-EXT1-S Sonnex Link over Fiber Extender.
1 the SWAMPE-8 functions provided through the SWAMP-24X8.
Plug-andplay connectivity affords an extremely easy installation with full control access to all
1. Item(s) sold separately.
2. For connection of the Sonnex Link between the SWAMPE-8 and SWAMP-24X8, use Crestron
DM-CBL-8G or high-quality CAT5e shielded twisted-pair cable (sold separately). The maximum cable length using DM-CBL-8G or CAT5e is 200 ft (61 m). For longer distances, use the S-EXT1-S
Sonnex Link over Fiber Extender (sold separately).
2 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Applications
The following diagram shows a SWAMPE-8 in a multizone application.
SWAMPE-8 in a Multizone Application
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 3
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Specifications
Specifications for the SWAMPE-8 are listed in the following table.
SWAMPE-8 Specifications
SPECIFICATION
Audio
Input Signal Types
Output Signal Types
Digital-to-Analog Conversion 1
Output Power 1
Damping Factor 1
Amplifier Monitoring 1
Frequency Response 1
Total Harmonic Distortion
(THD) 1
S/N Ratio 1
DETAILS
Sonnex Link
Stereo speaker level
24-bit 48 kHz
140 watts per channel at 8 ohms;
240 watts per channel at 4 ohms;
400 watts per channel at 8 ohms bridged
> 200 @ 20 Hz
Over current, over/under voltage, over temperature, dc offset, clipping
20 Hz to 20 kHz, ±0.5 dB
0.02%
Stereo Separation 1
Zone Separation 1
Zone Volume Level Control 1
Bass Control 1
Treble Control 1
Loudness Compensation 1
Dynamic Range Control 1
Balance Control 1
Mono Summing 1
Power Limiting 1
Tone Profiles 1
EQ Modes 1
GEQ Center Frequencies 1
GEQ Gain 1
PEQ Filter Types
PEQ Center Frequency 1
PEQ Gain 1
PEQ Bandwidth 1
> 105 dB S/PDIF in, > 100 dB balanced or unbalanced analog in, A-weighted
> 90 dB
> 95 dB
-80.0 to +20.0 dB, adjustable from 0% to
100% plus mute
±12.0 dB
±12.0 dB
On/Off
On/Off
Left/right adjustable
Selectable
Sonnex Speaker Protect (SSP ® ) output limiting; 2
Configurable 40 to 140 watts @ 8 ohms;
40 to 240 watts @ 4 ohms;
40 to 400 watts @ 8 ohms bridged
Flat, Classical, Jazz, Pop, Rock, Spoken
Word
5-band graphic or 5-band parametric EQ
63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz
±12.0 dB per band
EQ, High Pass, Low Pass, Treble Shelf,
Bass Shelf, Notch
10 Hz to 20 kHz per band
±12.0 dB per band
0.1 to 3.5 octaves per band
(Continued on following page)
4 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
SWAMPE-8 Specifications (Continued)
SPECIFICATION
Audio (Continued)
Speaker Profiles 1
Bus Volume Offset 1
Communications
Sonnex Link
Power Requirements
Main Power
SWAMPE-8
SWAMPIE-8
Environmental
Temperature
Humidity
Heat Dissipation
Enclosure
Chassis
Front Panel
Mounting
Dimensions
Height
Width
Depth
Weight
Available Models
SWAMPE-8
SWAMPIE-8
DETAILS
Comprises 5-band GEQ and SSP settings
±12.0 dB per zone for output bussing
64-channel (48 utilized) digital audio with embedded control, auto-discovery, auto-negotiating
12 amps @ 120 volts ac, 50/60 Hz (a dedicated 15 amp circuit is strongly recommended)
6 amps @ 220-240 volts ac, 50/60 Hz (a dedicated 10 amp circuit is strongly recommended)
41º to 104ºF (5º to 40ºC)
10% to 90% RH (non-condensing)
475 Btu/h (140 W @ 8 ohms)
750 Btu/h (240 W @ 4 ohms)
Metal with black finish, vented sides, variable-speed fan-cooled
Metal, black finish with polycarbonate label overlay
Freestanding or 3U 19-inch rack-mountable
(feet and rack ears included)
5.83 in (149 mm) with feet
5.20 in (133 mm) without feet
19.00 in (483 mm) with ears
17.29 in (439 mm) without ears
18.22 in (463 mm)
60.0 lb (27.3 kg)
Sonnex Multiroom Audio Expander, 8-Zone
Sonnex Multiroom Audio Expander –
International Version, 8-Zone
(Continued on following page)
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 5
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
SWAMPE-8 Specifications (Continued)
SPECIFICATION DETAILS
Available Accessories
AIR Series
ASPIRE Series
DM-8G-CONN
DM-8G-CONN-WG
AIR ® Outdoor Speakers
Aspire ® Speakers
Cable Connector for DM-CBL-8G
Cable Connector with Wire Guide for
DM-CBL-8G
Crimping Tool for DM-8G-CONN DM-8G-CRIMP
DM-8G-CRIMP-WG
DM-CBL-8G
ESSENCE Series
EXCITE Series
Crimping Tool for DM-8G-CONN-WG
High Performance CAT5e Shielded Twisted
Pair Cable
Essence ® Speakers
Excite ® Speakers
S-EXT1-S
SAROS Series
SAT-70V/100V
SWAMP(I)-24X8
Sonnex Link over Fiber Extender
Saros ® Speakers
Sonnex Output Transformer
Sonnex Multiroom Audio System
1. Typical of up to eight amplified stereo zone outputs.
2. As speaker ratings vary greatly across manufacturers, there is no guarantee that Sonnex Speaker
Protect protects against speaker damage in all situations.
Physical Description
This section provides information on the connections, controls, and indicators available on the SWAMPE-8.
SWAMPE-8 Physical View (Front)
SWAMPE-8 Physical View (Rear)
6 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8
SWAMPE-8 Overall Dimensions
Sonnex Multiroom Audio Expander, 8 Zone
18.22 in
(463 mm)
17.29 in
(439 mm)
19.00 in
(483 mm)
5.20 in
(133 mm)
5.83 in
(149 mm)
4
1 2 3
Operations Guide – DOC. 7051D
5 6
7
8
Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 7
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Connectors, Controls, and Indicators
# CONNECTORS,
INDICATORS
1
CONTROLS, AND
1 On/Off
DESCRIPTION
(1) Rocker switch, turns unit on and off
2
3
4
5
6
PWR LED
ZONE (1-8)
Buttons and LEDs
(1) Green LED indicates unit is turned on
(8) Push buttons and green LEDs, select output zone for routing and adjustment
DIGITAL IN
Green
LED
Yellow
LED
Pin 8 Pin 1
FUSE
120V~50/60Hz MAX
12A 4
(1) 8-wire RJ-45 female;
Sonnex link input;
Connects to SWAMP-24X8 Multiroom Audio
System 2 or S-EXT1-S Sonnex Link over Fiber
Extender 2 (each sold separately)
Green LED indicates link status;
Amber LED indicates data communication
The SWAMPE-8 requires a T15AH (1/4 in x
1-1/4 in, 250 V, 15 A, time-lag, high-rupture rated) fuse; 3
20 mm, 250 V, 8 A, time-lag, high-rupture rated) fuse 3
The SWAMPIE-8 requires a T8AH (5 mm x
(1) IEC 60320 C14, main power inlet;
Mates with removable power cord (included)
7 GROUND (1) 6-32 screw, chassis ground lug
8 SPEAKER OUTPUTS
(1-8)
(16) 2-pin 7.62 mm 15A detachable terminal blocks;
Power amplifier outputs;
Wire Size: Terminals accept up to 14 AWG;
The following outputs can be bridged together: 1 and 2 (L+R), 3 and 4 (L+R), 5 and
6 (L+R), and 7 and 8 (L+R);
(8) Red LEDs, indicate adjacent outputs are configured for bridged operation
NOTE: Outputs can only be bridged into an 8 ohm load.
1. Interface connectors for SPEAKER OUTPUTS ports are provided with the unit.
2. For connection of the Sonnex Link between the SWAMPE-8 and the SWAMP-24X8 or S-EXT1-S, use Crestron DM-CBL-8G or high-quality CAT5e shielded twisted-pair cable (sold separately). The maximum cable length is 200 ft (61 meters) per run.
3. Refer to “Fuse Replacement” on page 14 for additional details.
4. Port on SWAMPIE-8 is labeled 220-240V~50/60Hz MAX 6A.
8 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Setup
Ventilation
Rack Mounting
Operations Guide – DOC. 7051D
Sonnex Link Wiring
Crestron recommends using Crestron DM-CBL-8G or high-quality CAT5e shielded twisted-pair cable (sold separately) for Sonnex Link connections between the
SWAMPE-8 and the SWAMP-24X8 or S-EXT1-S.
NOTE: Shielded connectors such as the DM-8G-CONN (sold separately) must be used.
DM-CBL-8G wire can carry Sonnex Link signals up to 200 feet (61 meters).
Installation
The SWAMPE-8 should be used in a well-ventilated area. The venting holes should not be obstructed under any circumstances.
To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications. Consider using forced air ventilation or increasing the spacing between units to reduce overheating.
Contact with thermal insulating materials should be avoided on all sides of the unit.
The SWAMPE-8 can be mounted in a rack or stacked with other equipment. Two
“ears” are provided with the SWAMPE-8 so that the unit can be rack mounted.
These ears must be installed prior to mounting. Complete the following procedure to attach the ears to the unit. The only tool required is a #1 or #2 Phillips screwdriver.
WARNING: To prevent bodily injury when mounting or servicing this unit in a rack, observe the following guidelines:
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
NOTE: Observe the following guidelines when installing equipment in a rack:
• Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
• Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of airflow required for safe operation of the equipment is not compromised.
• Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
• Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 9
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
• Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).
NOTE: Feet are preinstalled for tabletop mounting or stacking. If the unit is to be rack mounted, the feet are not required and can be removed to provide more space in the rack.
To install the ears, use the following procedure.
CAUTION: To prevent equipment damage, use only the rack ears Crestron provides for this device.
1. There are screws that secure each side of the SWAMPE-8 top cover. Using a #1 or #2 Phillips screwdriver, remove the three screws closest to the front panel from one side of the unit. Refer to the diagram following step 3 for a detailed view.
2. Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 1.
3. Secure the ear to the unit with three screws from step 1, as shown in the following diagram.
Ear Attachment for Rack Mounting
Stacking
4. Repeat the procedure (steps 1 through 3) to attach the remaining ear to the opposite side.
Four “feet” are preinstalled with the SWAMPE-8 so that if the unit is not rack mounted, the feet can provide stability when the unit is placed on a flat surface or stacked.
NOTE: No more than two SWAMPE-8 units should be stacked.
10 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Connect the Device
Hardware Hookup
Make the necessary connections as called out in the illustration that follows this
paragraph. Refer to “Sonnex Link Wiring” on page 9 for additional information.
Apply power after all connections have been made.
Hardware Connections for the SWAMPE-8
DIGITAL IN:
From SWAMP-24X8 Sonnex Audio System or
S-EXT-1-S Sonnex Link over Fiber Extender
POWER:
From Line Voltage
SPEAKER OUTPUTS:
To Speakers or SAT-70V/100V
Sonnex Output Transformer
Ground
CAUTION: Keep the device unplugged until all the input and speaker wiring is complete.
CAUTION: Check the speaker wires for shorts and frayed wiring around the
SPEAKER OUTPUTS connectors.
NOTE: When installing the SWAMPE-8, a dedicated 15 amp circuit is strongly recommended. When installing the SWAMPIE-8, a dedicated 10 amp circuit is strongly recommended.
NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel).
NOTE: To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications.
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 11
Sonnex Multiroom Audio Expander, 8 Zone
Speaker Connections
Crestron SWAMP(I)E-8
Make speaker connections to the SWAMPE-8 as shown in the following diagram.
Speaker Connections
Bridge Speaker Outputs
(Optional)
-
+
L
-
R
NOTE: If the SAT-70V/100V Sonnex Output Transformer (sold separately) is connected to a speaker terminal, use the SAT-70V/100V profile built into the Sonnex
Tools application to configure a high-pass filter on the zone that is connected to
SAT-70V/100V. For details, refer to the Sonnex Tools help file.
The speaker outputs on the SWAMPE-8 can be bridged to deliver higher power to a speaker. The left channel on an individual output can be bridged with the right channel on the same output. Refer to the following diagram when bridging outputs.
Bridging Outputs
-
+
L
-
R
The possible bridging combinations are: Zone 1 + Zone 2, Zone 3 + Zone 4, Zone 5
+ Zone 6, Zone 7 + Zone 8. LEDs on the back of the SWAMPE-8 indicate bridged outputs.
After the zones are wired for bridged operation, the SWAMPE-8 must be configured with the SWAMP-24X8’s Installer Mode menu or with the Sonnex Tools application. Refer to the SWAMP(I)-24X8 Sonnex Multiroom Audio System
Operations Guide (Doc. 7049) at www.crestron.com/manuals or the Sonnex Tools help file for more information.
WARNING: This device is capable of delivering immense amounts of undistorted power to connected loudspeakers. Please use caution and adequate ear protection if listening to content at high volume levels as continued exposure to high sound pressure levels can cause permanent hearing impairment or loss.
12 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8
Subwoofer Applications
(Optional)
Sonnex Multiroom Audio Expander, 8 Zone
Using a sound level (SPL) meter and Sonnex Tools, outputs on SWAMPE-8 can be used to deliver sound to a left-right stereo pair and subwoofer speaker layout. There are two different wiring configurations that can be used.
Wiring Diagram: Passive Subwoofer Using an Additional Output Pair
BUSSED
-
LEFT
-
RIGHT
STEREO PAIR
-
SUB
ROOM
NOTE: In this diagram, output 1 and output 2 are used. However, other outputs
(either on the SWAMP-24X8 or the SWAMPE-8) can be used.
Wiring Diagram: Passive Subwoofer Using Bridged Output
BUSSED
BRIDGED
Operations Guide – DOC. 7051D
-
LEFT
-
RIGHT
-
STEREO PAIR SUB
ROOM
NOTE: In this diagram, output 1, output 2, and output 3 are used. However, other outputs (either on the SWAMP-24X8 or the SWAMPE-8) can be used as long as the bridged zones for the subwoofer are adjacent to each other (either on the
SWAMP-24X8 or the SWAMPE-8).
Perform the following procedure:
1. Connect the speakers and subwoofer as shown in one of the previous diagrams.
2. Refer to the SWAMP(I)-24X8 Sonnex Multiroom Audio System
Operations Guide (Doc. 7049) for configuration details.
Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 13
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Connect to SWAMP24X8 or
S-EXT1-S Sonnex Link over
Fiber Extender
The SWAMPE-8 can be connected to a SWAMP-24X8 (sold separately) or
S-EXT1-S Sonnex Link over Fiber Extender (sold separately) via shielded CAT5 cable.
SWAMP-24X8 to SWAMPE-8 Connection
Fuse Replacement
NOTE: When the SWAMP-24X8 is connected to a control system using Cresnet only one expander can be connected.
® ,
NOTE: When connecting a SWAMP-24X8 or S-EXT1-S to a SWAMPE-8,
Crestron recommends using Crestron DM-CBL-8G or high-quality CAT5e shielded twisted-pair cable. Shielded connectors such as the DM-8G-CONN (sold separately) must be used.
NOTE: The maximum cable length between a SWAMP-24X8 or S-EXT1-S and
SWAMPE-8 is 200 feet (61 meters).
If the SWAMPE-8 does not power up when it is plugged into an ac outlet and the power switch is engaged, the fuse may need to be replaced. The fuse holder is located on the rear panel, above and to the left of the IEC socket assembly. Perform the following to replace the fuse:
1. Disconnect power to the SWAMPE-8.
2. Use a flat head screwdriver to push in the fuse holder.
3. While pushing in the fuse holder, turn the screwdriver counterclockwise until the fuse holder pops out.
4. Remove the fuse from the fuse holder and insert a new fuse.
CAUTION: Use only the specified type of fuse. Failure to do so may cause damage to the SWAMPE-8.
NOTE: Two spare fuses are included.
14 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8
Label the Buttons
Sonnex Multiroom Audio Expander, 8 Zone
SWAMPE-8 MODEL
SWAMPE-8
(US & Canada)
SWAMPIE-8
(International/220-240 VAC)
REQUIRED FUSE TYPE
T15AH (1/4 in x 1-1/4 in, 250 V, 15 A, time-lag, high-rupture rated)
T8AH (5 mm x 20 mm, 250 V, 8 A, time-lag, high-rupture rated)
5. Insert the fuse holder into the SWAMPE-8.
6. Push in the fuse holder with a flat head screwdriver. While pushing in the fuse holder, turn the screwdriver clockwise until the fuse holder sets into place.
7. Push in the fuse holder a little further and turn the screwdriver clockwise until the fuse holder locks in place.
8. Connect power to the SWAMPE-8.
Use Crestron Engraver software to print custom labels for the SWAMPE-8’s front panel buttons and LEDs. Crestron recommends printing on 100-pound paper. Paper weighing less than 100 pounds tends to crumple while sliding in, while paper weighing more than 100 pounds may not fit.
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 15
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Configuration
The SWAMPE-8 is automatically configured from the front panel of a connected
SWAMP-24X8 or by Sonnex Tools software. For more information on configuration options, refer to the SWAMP(I)-24X8 Sonnex Multiroom Audio System Operations
Guide (Doc. 7049).
16 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Uploading and Upgrading
Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features.
However, before attempting to upload or upgrade it is necessary to establish communication.
Establishing Communication
All communication with the SWAMPE-8 is managed through the communication link with a connected SWAMP-24X8. For information, refer to the
SWAMP(I)-24X8 Sonnex Multiroom Audio System Operations Guide (Doc. 7049).
Programs and Firmware
Any program or firmware updates are managed by the connection with the
SWAMP-24X8. For information, refer to the SWAMP(I)-24X8 Sonnex Multiroom
Audio System Operations Guide (Doc. 7049).
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 17
Sonnex Multiroom Audio Expander, 8 Zone
Operation
Power
Zone Mode
Source Mode
Crestron SWAMP(I)E-8
The SWAMPE-8 operates in either the Zone mode or the Source mode. The
SWAMPE-8’s operating mode is determined by the operating mode of the
SWAMP-24X8.
For information on operating the SWAMP-24X8, refer to the SWAMP(I)-24X8
Sonnex Multiroom Audio System Operations Guide (Doc. 7049).
Turn on the SWAMPE-8 by moving the On/Off switch to . To turn off the
SWAMPE-8, move the On/Off switch to .
The Zone mode uses the SWAMP-24X8’s front panel to route a source signal to a selected zone. Perform the following to enter the Zone mode:
1. Place the SWAMP-24X8 in the Zone mode.
2. Press the ZONE button of the zone to be controlled.
3. Press the SOURCE button of the source to be routed. The associated
SOURCE and ZONE LEDs light.
Alternatively, press the ZONE button twice to turn on the zone and connect the last selected source.
The Source mode uses the SWAMP-24X8’s front panel to select a source signal and route it to multiple zones. Perform the following to enter the Source mode:
1. Place the SWAMP-24X8 in the Source mode.
2. On the SWAMP-24X8, press the SOURCE button of the source to be routed. The associated SOURCE LED lights.
3. On the SWAMPE-8, press the ZONE buttons of the zones to be selected.
The associated ZONE LED(s) lights.
To remove a zone from a source, press the desired ZONE button. The associated ZONE LED turns off.
18 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative.
SWAMPE-8 Troubleshooting
TROUBLE
Audio dropouts are heard on a
SWAMPE output zone.
Device loses functionality due to electrostatic discharge.
An incorrect audio signal is heard.
POSSIBLE CAUSE(S)
There is a bad (or missing) shield on the Sonnex cable connecting the SWAMP-24X8 and the peripheral device.
Ensure continuity and integrity of shield on both ends of the Sonnex cable.
Device is improperly grounded. Check that all ground connections have been made properly.
Signal is incorrectly routed.
Zone is incorrectly bussed with other zone(s).
CORRECTIVE
ACTION
Reroute the signal.
Remove the zone from the bus.
Check Wiring
To ensure optimum performance over the full range of the installation topology, use
Crestron Certified Wire. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire.
Reference Documents
All documents mentioned in this guide are available at www.crestron.com/manuals .
List of Related Reference Documents
DOCUMENT TITLE
SWAMP(I)-24X8 Sonnex Multiroom Audio System
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of Crestron worldwide offices at www.crestron.com/offices .
To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp . First-time users must establish a user account to fully benefit from all available features.
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 19
Sonnex Multiroom Audio Expander, 8 Zone Crestron SWAMP(I)E-8
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of the SWAMPE-8, additional information may be made available as manual updates.
These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an “Addendum” in the Download column.
20 • Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 Operations Guide – DOC. 7051D
Crestron SWAMP(I)E-8 Sonnex Multiroom Audio Expander, 8 Zone
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange or service without prior authorization from
Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer.
Only authorized Crestron dealers may contact the factory and request an RMA (Return
Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number and return address.
2. Products may be returned for credit, exchange or service with a Crestron Return Merchandise
Authorization (RMA) number. Authorized returns must be shipped freight prepaid to Crestron,
6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. Crestron reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by Crestron, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser.
Crestron Limited Warranty
Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from Crestron, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touch screen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
Crestron shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended or if it has been subjected to misuse, accidental damage, modification or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or made by the purchaser for a third party.
Crestron shall, at its option, repair or replace any product found defective, without charge for parts or labor.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Operations Guide – DOC. 7051D Sonnex Multiroom Audio Expander, 8 Zone: SWAMP(I)E-8 • 21
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576 www.crestron.com
Operations Guide – DOC. 7051D
(2028552)
08.14
Specifications subject to change without notice.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Introduction
- 7 Features and Functions
- 9 Applications
- 9 Specifications
- 12 Physical Description
- 15 Setup
- 15 Sonnex Link Wiring
- 15 Installation
- 17 Hardware Hookup
- 22 Configuration
- 23 Uploading and Upgrading
- 23 Establishing Communication
- 23 Programs and Firmware
- 24 Operation
- 25 Problem Solving
- 25 Troubleshooting
- 25 Check Wiring
- 25 Reference Documents
- 25 Further Inquiries
- 26 Future Updates
- 27 Return and Warranty Policies
- 27 Merchandise Returns / Repair Service
- 27 Crestron Limited Warranty