VAUXHALL Mokka Infotainment Manual Model Year 2013 Edition

Infotainment Manual Model Year 2013 Edition: June 2012 TS 1725-A-13
0-1
VAUXHALL Mokka
Infotainment Manual
Model Year 2013
Edition: June 2012
TS 1725-A-13
Contents
Navi 600 ......................................... 3
CD 400 ......................................... 91
Navi 600
Introduction .................................... 4
Radio ........................................... 15
CD Player .................................... 24
AUX input ..................................... 27
USB port ...................................... 28
Digital picture frame ..................... 31
Navigation .................................... 34
Speech recognition ...................... 72
Phone .......................................... 77
Index ............................................ 88
4
Introduction
Introduction
General information ....................... 4
Theft-deterrent feature ................... 5
Control elements overview ............ 6
Usage ............................................ 9
Basic operation ............................ 10
Tone settings ............................... 12
Volume settings ........................... 14
General information
The Infotainment system provides
you with state-of-the-art in-car
infotainment.
For the AM, FM and DAB wavebands
the radio is equipped with twelve
automatically assignable channel
presets. Furthermore, 36 channels
can be allocated manually
(waveband-independent).
The integrated audio player will
entertain you with audio CDs and
MP3/WMA CDs.
Furthermore, you can connect
external data storage devices, e.g.
iPod, MP3 player or USB stick, or a
portable CD player to the
Infotainment system as further audio
sources.
The digital sound processor provides
you with several preset equalizer
modes for sound optimisation.
The navigation system with dynamic
route planning will reliably guide you
to your destination, and, if desired,
will automatically avoid traffic jams or
other traffic problems.
Optionally, the Infotainment system
can be operated using controls on the
steering wheel or via the speech
recognition system (if available).
In addition the Infotainment system
can be equipped with a mobile phone
portal.
The well-thought-out design of the
control elements, the clear displays
and a large multifunction knob enable
you to control the system easily and
intuitively.
Important information on
operation and traffic safety
9 Warning
The Infotainment system has to be
used so that the vehicle can be
driven safely at all times. If in doubt
stop your vehicle and operate the
Infotainment system while the
vehicle is stationary.
Introduction
9 Warning
The usage of the navigation
system does not release the driver
from the responsibility for a
correct, vigilant attitude in road
traffic. The related traffic
regulations must always be
followed.
Only make entries (e.g.
addresses) with the vehicle
stationary.
If a navigation instruction
contradicts traffic regulations, the
traffic regulations always apply.
9 Warning
In some areas one-way streets
and other roads and entrances
(e.g. pedestrian zones) that you
are not allowed to turn into are not
marked on the map. In such areas
the Infotainment system may
issue a warning that must be
accepted. Here you must pay
particular attention to one-way
streets, roads and entrances that
you are not allowed to drive into.
Radio reception
Radio reception may be disrupted by
static, noise, distortion or loss of
reception due to
■ changes in distance from the
transmitter,
■ multi-path reception due to
reflection,
■ shadowing.
Theft-deterrent feature
The Infotainment system is equipped
with an electronic security system for
the purpose of theft deterrent.
The Infotainment system therefore
functions only in your vehicle and is
worthless to a thief.
5
6
Introduction
Control elements overview
Navi 600
Introduction
1
RADIO (BAND) ..................... 15
2
Activate radio or change
waveband .............................. 15
CD/AUX ................................ 27
3
Start CD/MP3/WMA
replay or change audio
source ................................... 27
Search backwards ................ 15
4
6
7
5
Search forwards .................... 15
13 INFO ....................................... 6
Radio: search forwards ......... 15
Radio: information on the
currently played station ......... 15
CD/MP3/WMA: skip track
forwards ................................ 25
AS (1/2) ................................. 16
Automatic memory levels
(preset radio stations) ........... 16
Radio: search backwards ..... 15
Short press: select
autostore list .......................... 16
CD/MP3/WMA: skip track
backwards ............................. 25
Radio station buttons 1...6 .... 16
8
Long press: save stations
automatically ......................... 16
FAV (1/2/3) ............................ 16
9
Lists of favourites (preset
radio stations) ....................... 16
TP ......................................... 20
Long press: save station ....... 16
Short press: select station .... 16
m knob .................................... 9
Press: switch on/off
Infotainment system ................ 9
Turn: adjust volume ................ 9
7
Activate or deactivate
radio traffic service ................ 20
10 CD ejection ........................... 25
11 CONFIG ................................ 14
System settings ..................... 14
12 TONE .................................... 12
Tone settings ........................ 12
CD/MP3/WMA:
information on the
currently inserted CD ............ 25
Digital picture frame:
shows currently selected
picture/photo ......................... 31
Navigation: information,
e.g., on the current location . . 34
14 Multifunction knob ................. 10
Turn: mark menu options
or set numeric values ........... 10
Press (the outer ring):
select/activate the marked
option; confirm set value;
switch function on/off ............ 10
15 Eight-way switch ................... 35
Navigation: move display
window in map view .............. 35
16 CD slot .................................. 25
8
Introduction
17 BACK .................................... 10
Steering wheel audio controls
If radio is active: turn
upwards/downwards to
select next/previous
preset radio station ............... 15
Menu: one level back ............ 10
Input: delete last character
or entire entry ........................ 10
18 RPT ....................................... 65
If CD player is active: turn
upwards/downwards to
select next/previous CD/
MP3/WMA track .................... 25
Repeat last navigation
message ............................... 65
19 DEST .................................... 35
Navigation destination
entry ...................................... 35
20 PHONE ................................. 77
Open telephone menu .......... 84
If Phone portal is active:
turn upwards/downwards
to select next/previous
entry in call list ...................... 84
1
Short press: take phone call . 77
or dial number in call list ....... 84
Activate/deactivate mute ......... 9
21 NAVI ...................................... 35
or activate speech
recognition (if available) ........ 72
Display map ......................... 35
Long press: show call list ...... 84
2
or deactivate speech
recognition (if available) ........ 72
SRC (Source) .......................... 9
Press: select audio source ...... 9
3
4
5
If Phone portal is active
and calls waiting: turn
upwards/downwards to
switch between calls ............. 84
Increase volume ...................... 9
Reduce volume ....................... 9
Short press: end/decline
call ......................................... 84
or close call list ...................... 84
or activate/deactivate mute ..... 9
or deactivate speech
recognition (if available) ........ 72
Introduction
Usage
Control elements
The Infotainment system is operated
via function buttons, multifunctional
knobs and menus that are shown on
the display.
Inputs are made optionally via:
■ the central control unit in the
instrument panel 3 6
■ controls on the steering wheel 3 6
■ the speech recognition system (if
available) 3 72
Switching the Infotainment
system on or off
Press the X knob briefly. After
switching on, the last selected
Infotainment source is active.
Automatic switch-off
If the Infotainment system has been
switched on using the X knob when
the ignition was switched off, it will
switch off again automatically after
30 minutes.
Setting the volume
Turn the X knob. The current setting
is shown on the display.
When the Infotainment system is
switched on, the last selected volume
is set, provided that volume is lower
than the maximum start-up volume.
The following can be set separately:
■ the maximum start-up volume
3 14
■ the volume of the traffic
announcements 3 14
■ the volume of the navigation
messages 3 35
Speed compensated volume
When speed compensated volume is
activated 3 14 the volume is
adapted automatically to compensate
for the road and wind noise as you
drive.
Mute
Press the PHONE button (if Phone
portal available: press for a few
seconds) to mute the audio sources.
9
To cancel mute again: turn the X
knob or press the PHONE button
again (if Phone portal available: press
for a few seconds).
Volume limitation at high
temperatures
At very high temperatures inside the
vehicle the Infotainment system limits
the maximum adjustable volume. If
necessary the volume is decreased
automatically.
Modes of operation
Radio
Press the RADIO button to open the
radio main menu or to change
between the different wavebands.
Press the multifunction knob to open
a submenu with options for station
selection.
Detailed description of the radio
functions 3 15.
10
Introduction
Audio players
Press the CD/AUX button to open the
CD, USB, iPod or AUX menus (if
available) or to swap between these
menus.
Press the multifunction knob to open
a submenu with options for track
selection.
Detailed description of:
■ CD player functions 3 25
■ AUX input functions 3 27
■ USB port functions 3 28
Navigation
Press the NAVI button and then the
multifunction knob to open the
Navigation menu.
Detailed description of the navigation
system functions 3 35.
Phone
(if Phone portal is available)
Press the PHONE button to open the
telephone menu.
Press the multifunction knob to open
a submenu with options for the input
or selection of numbers.
Detailed description of the mobile
phone portal functions 3 77.
Press and hold the BACK button for a
few seconds to delete the entire entry.
Basic operation
Examples of menu operation
Multifunction knob
The multifunction knob is the central
control element for the menus.
Turn the multifunction knob:
■ to mark a menu option
■ to set a numeric value
Press the outer ring of the
multifunction knob:
■ to select or activate the marked
option
■ to confirm a set value
■ to switch a system function on/off
BACK button
Press the BACK button briefly to:
■ exit a menu
■ return from a submenu to the next
higher menu level
■ delete the last character in a
character sequence
Selecting an option
Turn the multifunction knob to move
the cursor (= coloured background) to
the desired option.
Press the multifunction knob to select
the marked option.
Introduction
Submenus
An arrow on the right-hand edge of
the menu indicates that after
selection of the option a submenu
with further options will be opened.
11
Setting a value
Switching a function on or off
Turn the multifunction knob to change
the current value of the setting.
Press the multifunction knob to
confirm the set value.
Turn the multifunction knob to mark
the function to be switched on or off.
Press the multifunction knob to switch
between the settings On and Off.
Activating a setting
Turn the multifunction knob to mark
the desired setting.
Press the multifunction knob to
activate the setting.
12
Introduction
Entering a character sequence
Tone settings
Setting bass, middle and treble
In the tone settings menu the tone
characteristic can be set differently for
each radio waveband and each audio
player source.
To enter character sequences, e.g.
telephone numbers or road names:
Turn the multifunction knob to select
the desired character.
The last character in the character
sequence can be deleted using the
BACK button. Pressing and holding
the BACK button deletes the entire
entry.
Press the multifunction knob to
confirm the selected character.
Select Bass, Middle or Treble.
Set the desired value for the option
selected.
Press the TONE button to open the
tone menu.
Introduction
13
Setting the volume distribution
between front - rear
Setting the volume distribution
between right - left
Optimising the tone for the style
of music
Select Fader.
Set the desired value.
Select Balance.
Set the desired value.
Select EQ (Equalizer).
The displayed options offer optimised
bass, middle and treble presettings
for the relevant style of music.
Select the required option.
Setting an individual setting to
“0” or "Off"
Select the desired option and press
and hold the multifunction knob for a
few seconds.
Setting all settings to "0" or "Off"
Press and hold the TONE button for a
few seconds.
14
Introduction
Volume settings
Speed dependent volume
Maximum startup volume
Press the CONFIG button to open the
system settings menu.
Select Radio settings and then
Maximum startup volume.
Set the desired value.
Volume of the traffic
announcements (TA)
The volume of the traffic
announcements can be increased or
reduced proportionate to the normal
audio volume.
Press the CONFIG button to open the
system settings menu.
Select Radio settings and then Speed
dependent volume.
Speed dependent volume can be
deactivated or the degree of volume
adaptation can be selected in the
menu displayed.
Select the required option.
Press the CONFIG button to open the
system settings menu.
Select Radio settings, RDS options
and TA volume.
Set the desired value.
Radio
Radio
Usage .......................................... 15
Station search .............................. 15
Autostore lists .............................. 16
Favourite lists ............................... 16
Waveband menus ........................ 17
Radio data system (RDS) ............ 20
Digital audio broadcasting ........... 22
Usage
Station search
Control buttons
Automatic station search
The most important buttons for
control of the radio are as follows:
■ RADIO: Activate radio
■ s u: Station search
■ AS: Autostore lists
■ FAV: Favourite lists
■ 1...6: Preset buttons
■ TP: Radio traffic service 3 20
Activating the radio
Press the RADIO button to open the
radio main menu.
The station last played will be
received.
Selecting the waveband
Press the RADIO button once or
several times to select the desired
waveband.
The station last played in that
waveband will be received.
15
Briefly press the button s or u
to play the previous/next station in the
station memory.
Manual station search
Press and hold s or u button.
Release button when the required
frequency has almost been reached
on the frequency display.
A search is made for the next station
that can be received and it is played
automatically.
Manual station tuning
FM waveband
Press the multifunction knob to open
the FM menu and select Manual
tuning FM.
Turn the multifunction knob and set
the optimal reception frequency on
the pop-up frequency display.
16
Radio
Storing stations manually
AM waveband
Turn the multifunction knob and set
the optimal reception frequency on
the pop-up frequency display.
Stations can also be stored manually
in the autostore lists.
Set the station to be stored.
Briefly press the AS button to open an
autostore list or to switch to another
autostore list.
To store the station in a list position:
press the corresponding station
button 1...6 until a confirmation
message is displayed.
DAB waveband
Press the multifunction knob to open
the DAB menu and select DAB
manual tuning.
Turn the multifunction knob and set
the required reception frequency on
the pop-up frequency display.
Autostore lists
The stations that can be received best
in a waveband can be searched for
and stored automatically via the
autostore function.
Note
The currently received station is
highlighted.
Each waveband has 2 autostore lists
(AS 1, AS 2), in each of which
6 stations can be stored.
Automatic station storing
Press and hold the AS button until an
autostore message is displayed. The
12 strongest stations in the current
waveband will be stored in the
2 autostore lists.
To abort the autostore procedure,
press the multifunction knob.
Note
Manually stored stations are
overwritten in an automatic station
storing process.
Retrieving a station
Briefly press the AS button to open an
autostore list or to switch to another
autostore list.
Briefly press one of the station
buttons 1...6 to open the station at the
corresponding list position.
Favourite lists
Stations of all wavebands can be
stored manually in the favourite lists.
Radio
Retrieving a station
Briefly press the FAV button to open
a favourite list or to switch to another
favourite list. Briefly press one of the
station buttons 1...6 to open the
station at the related list position.
Defining the number of available
favourite lists
Waveband menus
Alternative facilities for station
selection are available via wavebandspecific menus.
With the radio main menu active,
press the multifunction knob to open
the relevant waveband menu.
Note
The following FM specific displays
are shown as examples.
6 stations can be stored in each
favourite list. The number of available
favourite lists can be set (see below).
Note
The currently received station is
highlighted.
Storing a station
Set the station to be stored.
Briefly press the FAV button to open
a favourite list or to switch to another
favourite list.
To store the station in a list position:
press the corresponding station
button 1...6 until a confirmation
message is displayed.
Press CONFIG button.
Select Radio settings and then Radio
favourites.
Select the desired number of
available favourite lists.
17
Favourites list
Select Favourites list. All stations
saved in the favourites lists are
displayed.
18
Radio
DAB waveband
Turn the multifunction knob.
All receivable DAB stations 3 22 in
the current reception area are
displayed.
Note
If no station list has been created
beforehand, the Infotainment
system performs an automatic
station search.
If the stations stored in a wavebandspecific station list can no longer be
received:
Select the corresponding command
to update a station list.
A station search is started. Once the
search is finished, the station
previously selected is played.
To cancel the station search: press
multifunction knob.
Note
If a waveband specific station list is
updated the corresponding category
list (if available) is also updated.
Select the required station.
Note
The currently received station is
marked by i.
Manual tuning
Description see "Manual station
tuning" above.
Station lists
AM/FM waveband
Select AM station list or FM station
list.
All receivable AM/FM stations in the
current reception area are displayed.
Updating station lists
Select the required station.
Note
The currently received station is
marked by i.
Important information on updating the
station lists
The dual tuner in the Infotainment
system continuously updates the
station lists in the background. This
ensures that, e.g., the station lists
always contain the stations that can
be received in the local area during a
long motorway journey. As the
automatic updating takes a certain
amount of time, not all stations that
can be received may be available at
Radio
19
once in the station list at a sudden
change in reception area. In such
circumstances the updating of the
station lists can be accelerated using
the corresponding command for
updating a station list.
Category lists
Numerous RDS stations 3 20
broadcast a PTY code, which
specifies the type of programme
transmitted (e.g. news). Some
stations also change the PTY code
depending on the content currently
being transmitted.
The Infotainment system stores these
stations, sorted by programme type,
in the corresponding category list.
To search for a programme type
determined by station: select the
waveband-specific category list
option.
A list of programme types available at
the moment is displayed.
Select desired programme type.
A list of stations is displayed that
transmit a programme of the selected
type.
Select the required station.
The category list is also updated
when the corresponding waveband
specific station list is updated.
Note
The currently received station is
marked by i.
DAB announcements
Besides their music programmes,
numerous DAB stations 3 22
broadcast various announcement
categories.
20
Radio
The currently received DAB service
(programme) is interrupted when any
announcements of previously
activated categories are pending.
Activating announcement categories
Select DAB announcements in the
DAB menu.
Activate the desired announcement
categories.
Several announcement categories
can be selected at the same time.
Note
DAB announcements can only be
received if the DAB waveband is
activated.
Radio data system (RDS)
RDS is a service of FM stations that
considerably facilitates the finding of
the desired station and its fault-free
reception.
Advantages of RDS
■ On the display, the programme
name of the set station appears
instead of its frequency.
■ On station search, the Infotainment
system tunes in to RDS stations
only.
■ The Infotainment system always
tunes into the best receivable
broadcasting frequency of the set
station by means of AF (Alternative
Frequency).
■ Depending on the station that is
received, the Infotainment system
displays radio text that can contain,
for example, information about the
current programme.
Configuring RDS
To open the menu for the RDS
configuration:
Press the CONFIG button.
Select Radio settings and then RDS
options.
Radio
If regionalization is switched on, only
alternative frequencies (AF) with the
same regional programmes are
selected.
If regionalization is switched off,
alternative frequencies of the stations
are selected without regard to
regional programmes.
Switching RDS on and off
Set RDS to On or Off.
Note
If RDS is switched off, it will be
automatically switched on again
when a radio station is changed (by
search function or preset button).
Switching regionalization on and off
(RDS must be activated for
regionalization)
At certain times, some RDS stations
broadcast regionally different
programmes on different frequencies.
Set Regional to On or Off.
RDS scrolling text
Some RDS stations use the lines for
indicating the name of the
programme to also indicate additional
information. During this process the
programme name is hidden.
To prevent additional information
being displayed:
Set RDS-text scroll freeze to On.
Radio text
If RDS and reception of an RDS
station are activated, information
about the programme that is currently
receivable and about the music track
currently playing are displayed below
the programme name.
To show or hide the information:
Set Radio text to On or Off.
21
TA volume
The volume of the traffic
announcements (TA) can be preset
3 14.
Radio traffic service
(TP = Traffic Programme)
Radio traffic service stations are RDS
stations that broadcast traffic news.
Switching the radio traffic service on
and off
To switch the traffic announcement
standby facility of the Infotainment
system on and off:
Press the TP button.
■ If the radio traffic service is
switched on, [ ] is indicated on the
display in black (grey if radio traffic
service is switched off).
■ Only radio traffic service stations
are received.
■ If the current station is not a radio
traffic service station, a search is
started automatically for the next
radio traffic service station.
22
Radio
■ If a radio traffic service station has
been found, [TP] is indicated on the
display in black. If no radio traffic
service stations are found, TP is
displayed in grey.
■ Traffic announcements are played
at the preset TA volume 3 14.
■ If the radio traffic service is
switched on, CD/MP3 replay is
interrupted for the duration of the
traffic announcement.
Listening to traffic announcements
only
Switch on the radio traffic service and
completely turn down the volume of
the Infotainment system.
Blocking out traffic announcements
To block out a traffic announcement,
e.g. during CD/MP3 replay:
Press TP button or the multifunction
knob to confirm the cancel message
on the display.
The traffic announcement is aborted,
but the radio traffic service remains
switched on.
EON (Enhanced Other Networks)
With EON you can listen to radio
traffic announcements even if the
station you have set does not
broadcast its own radio traffic service.
If such a station is set, it is displayed
in black as for radio traffic service
stations TP.
Digital audio broadcasting
Digital audio broadcasting (DAB) is
an innovative and universal
broadcast system.
DAB stations are indicated by the
programme name instead of the
broadcasting frequency.
General information
■ With DAB, several radio
programmes (services) can be
broadcast on a single frequency
(ensemble).
■ Besides high-quality digital audio
services, DAB is also able to
transmit programme-associated
data and a multitude of other data
services including travel and traffic
information.
■ As long as a given DAB receiver
can pick up the signal sent out by a
broadcasting station (even if the
signal is very weak), sound
reproduction is ensured.
Radio
■ There is no fading (weakening of
the sound) that is typical of AM or
FM reception. The DAB signal is
reproduced at a constant volume.
■ Interference caused by stations
that are on nearby frequencies (a
phenomenon that is typical of AM
and FM reception) does not occur
in connection with DAB.
■ If the DAB signal is reflected by
natural obstacles or buildings, the
reception quality of DAB is
improved, whereas AM or FM
reception is considerably impaired
in such cases.
Configuring DAB
Press the CONFIG button.
Select Radio settings and then DAB
settings.
The following options are available in
the configuration menu:
■ Dynamic audio adaption: with this
function activated, the dynamic
range of the DAB signal is reduced.
That means the level of the loud
sounds is reduced, but not the level
of the quiet sounds. Therefore the
volume of the Infotainment system
23
can be raised to a point where the
quiet sounds are audible, without
the loud sounds being too loud.
■ Frequency band: after selection of
this option the user can define
which DAB wavebands are to be
received by the Infotainment
system.
24
CD Player
CD Player
General information ..................... 24
Usage .......................................... 25
General information
The Infotainment system's CD player
can replay audio CDs and MP3/WMA
CDs.
Important information about
audio CDs and MP3/WMA CDs
Caution
Under no circumstances place
DVDs, single-CDs with a diameter
of 8 cm or shaped CDs in the audio
player.
You must not put any stickers on
CDs. These discs can get jammed
in the CD drive and ruin the drive.
An expensive replacement of the
device will then be necessary.
■ Audio CDs with copy protection,
which are not in compliance with
the audio CD standard, may not
play correctly or not at all.
■ Self-recorded CD-Rs and CD-RWs
are more vulnerable to mishandling
than prerecorded CDs. Correct
■
■
■
■
■
■
■
handling, especially in the case of
self-recorded CD-Rs and CD-RWs,
must be ensured; see below.
Self-recorded CD-Rs and CD-RWs
may not play correctly or not at all.
On mixed mode CDs (combinations
of audio and data, e.g. MP3), only
the audio tracks will be detected
and played.
Avoid leaving fingerprints when you
change CDs.
Put CDs back in their sleeves
immediately after removing them
from the audio player in order to
protect them from damage and dirt.
Dirt and liquids on CDs can smear
the lens of the audio player inside
the device and cause faults.
Protect CDs from heat and direct
sunlight.
The following restrictions apply for
the data stored on an MP3/WMA
CD:
Maximum folder structure depth:
11 levels.
Maximum number of MP3/WMA
files that can be saved: 1000.
CD Player
WMA files with Digital Rights
Management (DRM) from online
music shops cannot be played.
WMA files can only be played back
safely if they were created with
Windows Media Player version 8 or
later.
Applicable playlist
extensions: .m3u, .pls
Playlist entries must be in the form
of relative paths.
■ This chapter deals only with playing
MP3 files since the operation for
MP3 and WMA files is identical.
When a CD with WMA files is
loaded MP3 related menus are
displayed.
Usage
25
Depending on the data stored on the
audio CD or MP3 CD differing
information about the CD and the
current music track will be shown on
the display.
Selecting a track
Turn the multifunction knob to display
a list of all tracks on the CD. The
currently played track is preselected.
Select the desired track.
Skipping to the next track or
previous track
Starting CD replay
Push CD with the labelled side
upward into the CD slot until it is
pulled in.
CD replay starts automatically and
the Audio CD or Audio MP3 menu is
displayed.
If there is already a CD in the unit, but
the Audio CD or Audio MP3 menu is
not active:
Press CD/AUX button.
The Audio CD or Audio MP3 menu is
opened and CD replay is started.
Briefly press s or u button once
or several times.
Track search forward or
backward
Briefly press s or u button and
then press s or u button again
and keep pressed until the desired
track is displayed.
Fast forward or rewind
Press and hold button s or u to
fast forward or rewind the current
track.
26
CD Player
Selecting tracks using the audio
CD or MP3 menu
During MP3 replay
During audio CD replay
Press the multifunction knob to open
the audio CD related menu.
To play all tracks in random order: set
Shuffle songs (RDM) to On.
To select a track on the audio CD:
select Track list and then select the
desired track.
Press the multifunction knob to open
the MP3 related menu.
To play all tracks in random order: set
Shuffle songs (RDM) to On.
To select a track from a folder or
playlist (if available): select Folders or
Playlists.
Select a folder or playlist and then
select the desired track.
Select Search to open a menu with
additional options for track search
and selection.
Depending on the amount of tracks
saved, the search process may take
several minutes.
Select a search option and then
select the desired track.
Removing a CD
Press d button.
The CD is pushed out of the CD slot.
If the CD is not removed after
ejection, it will be drawn back in again
automatically after a few seconds.
AUX input
AUX input
General information
27
Usage
Press the CD/AUX button once or
several times to activate the AUX
mode.
General information ..................... 27
Usage .......................................... 27
In the centre console in front of the
gearshift lever there is an AUX socket
for the connection of external audio
sources.
It is possible, for example, to connect
a portable CD player with a 3.5 mm
jack plug to the AUX input.
Note
The socket must always be kept
clean and dry.
An audio source that is connected to
the AUX input can be operated only
via the control elements of the audio
source.
28
USB port
USB port
General information
General information ..................... 28
Playing saved audio files ............. 29
In the centre console in front of the
gearshift lever there is a USB socket
for the connection of external audio
data sources.
Note
The socket must always be kept
clean and dry.
An MP3 player, USB drive or an iPod
can be connected to the USB port.
Note
Not all MP3 player, USB drive and
iPod models are supported by the
Infotainment system.
Important information
MP3 player and USB drives
■ The MP3 players and USB drives
connected must comply with the
USB Mass Storage Class
specification (USB MSC).
■ Only MP3 players and USB drives
with a cluster size smaller or equal
to 64 kB in the FAT16/FAT32 file
system are supported.
■ Hard disk drives (HDD) and are not
supported.
■ USB hubs are not supported.
■ The following restrictions apply for
the data stored on an MP3 Player
or USB device:
Maximum folder structure depth:
11 levels.
Maximum number of MP3/WMA
files that can be saved: 1000.
WMA files with Digital Rights
Management (DRM) from online
music shops cannot be played.
WMA files can only be played back
safely if they were created with
USB port
Windows Media Player version 8 or
later.
Applicable playlist
extensions: .m3u, .pls
Playlist entries must be in the form
of relative paths.
The system attribute for folders/
files that contain audio data must
not be set.
Press the CD/AUX button once or
several times to activate the audio
USB mode.
Replay of the audio data stored on the
USB device is started.
The operation of data sources
connected via USB is the same as for
an audio MP3/WMA CD 3 25.
29
The operation of the iPod connected
via USB is mainly the same as for an
audio MP3/WMA CD 3 25.
On the following pages only the
aspects of operation that are
different/additional are described.
iPod functions
iPod
Playing saved audio files
MP3 player / USB drives
Press the CD/AUX button once or
several times to activate the audio
iPod mode.
Replay of the audio data stored on the
iPod is started.
Depending on the data saved, there
are various options for the selection
and playing of tracks.
Press the multifunction knob and then
select Search to display the options
available.
30
USB port
The search process on the device
may take several seconds.
Digital picture frame
Digital picture frame
General information ..................... 31
Usage .......................................... 31
General information
31
Using the digital picture frame
function you can view your favourite
pictures (or photos), one at a time, on
the display of the Infotainment
system.
You can download your favourite
pictures from a USB drive connected
to the USB port 3 28 of the
Infotainment system.
Up to 10 pictures can be stored in the
Infotainment system's memory.
The pictures are shown on the display
in their original ratio (borders if
necessary are black) and orientation.
■ Only pictures in JPEG standard
format (file extensions, e.g., .jpg
or .jpeg) are supported.
Example: "F:\myPicture.jpg",
where "F:\" is the root directory of
the USB drive.
■ The maximum supported resolution
of a picture is 12 Mega pixel.
Pictures with higher resolutions are
down-scaled (resized) during
download.
Pictures with lower resolutions are
not up-scaled (not resized) during
download and centred in the middle
of the display.
Important information
Usage
■ The pictures you want to download
need to be stored in the root
directory (e.g., "F:\") of the USB
drive.
■ Only the first 100 pictures
(sequentially sorted as stored in the
root directory of the USB drive) will
be offered for download.
Downloading and/or removing
pictures
Connect a USB drive with your
favourite pictures (or photos) stored
on it to the USB port 3 28 of the
Infotainment system.
32
Digital picture frame
Press the CONFIG button, select
Display settings, and then select
Picture frame. The menu shown
below is displayed.
Select Add / Remove pictures to open
the menu shown below.
The menu shows a list with the file
names of all pictures (note the
restrictions described in "Important
information" above) stored in the root
directory of the connected USB drive.
If pictures were already stored in the
Infotainment system's memory, that
"old" pictures are listed first on the
menu and indicated by MEM, see
image below.
If you want to have removed "old"
pictures, you need to deselect them
before downloading new pictures.
Select max. 10 pictures that you want
to be downloaded (added) to the
Infotainment system's memory or
stay stored in that memory.
Select Confirm to start the picture
download and/or removal.
A message is displayed that shows
how many pictures are going to be
downloaded and/or removed.
Select Continue if you want to start
the download and/or removal.
Displaying pictures
Pictures stored in the Infotainment
system's memory can be shown on
the display one at a time.
Digital picture frame
Press the CONFIG button, select
Display settings, select Picture
frame, and then select Picture
selection. The menu shown below is
displayed.
Select the picture you want to be
shown on the display.
Press the INFO button several times
until the currently selected picture is
shown on the display.
To display a default Infotainment
menu again, press any button on the
Infotainment system.
As long as a picture stays selected in
the Picture selection menu, it can be
displayed at any time using the
INFO button.
33
34
Navigation
Navigation
General information ..................... 34
Usage .......................................... 35
Destination input .......................... 44
Guidance ..................................... 58
Dynamic guidance ....................... 65
Maps ............................................ 65
Symbols overview ........................ 68
General information
The navigation system will reliably
guide you to your destination without
the need to read maps, even if you
have no local knowledge whatsoever.
The current traffic situation is taken
into account in the route calculation if
dynamic route guidance is used. For
this purpose the Infotainment system
receives traffic announcements in the
current reception area via RDS-TMC.
The navigation system cannot,
however, take into account traffic
incidents, traffic regulations changed
at short notice and hazards or
problems that arise suddenly (e.g.
road works).
Caution
The usage of the navigation
system does not release the driver
from the responsibility for a
correct, vigilant attitude in road
traffic. The relevant traffic
regulations must always be
followed. If a navigation instruction
contradicts traffic regulations, the
traffic regulations always apply.
Functioning of the navigation
system
The position and movement of the
vehicle are detected by the navigation
system using sensors. The travelled
distance is determined by the
vehicle’s speedometer signal, turning
movements on bends by a gyro
sensor. The position is determined by
the GPS satellites (Global Positioning
System).
By comparing the sensor signals with
the digital maps on the map SD card,
it is possible to determine the position
with an accuracy of approx.
10 metres.
The system will also work with poor
GPS reception, however, the
accuracy of the determination of the
position will be reduced.
Navigation
After the entry of the destination
address or point of interest (nearest
petrol station, hotel, etc.) the route is
calculated from the current location to
the destination selected.
The route guidance is provided by
voice output and an arrow, as well as
with the aid of a multi-colour map
display.
TMC traffic information system
and dynamic route guidance
The TMC traffic information system
receives all current traffic information
from TMC radio stations. If dynamic
route guidance is active, this
information is included in the
calculation of the overall route. During
this process, the route is planned so
that traffic problems related to preselected criteria are avoided.
If there is a traffic problem during
active route guidance, depending on
the pre-settings, a message appears
as to whether the route should be
changed.
TMC traffic information is displayed in
the route guidance display as
symbols or as detailed text on the
TMC messages menu.
To be able to use TMC traffic
information, the system has to receive
TMC stations in the relevant region.
Dynamic route guidance only works if
traffic information is received via the
TMC traffic information system.
The dynamic route guidance function
can be deactivated in the Navigation
options menu, see chapter
"Guidance" 3 58.
Map data
All required map data is stored on an
SD card provided with the
Infotainment system.
Detailed descriptions on map SD card
handling and replacement, see
chapter "Maps" 3 65
35
Usage
Control elements
The most important navigationspecific control elements are as
follows:
NAVI button: activate navigation;
show current position (if route
guidance inactive); show calculated
route (if route guidance active); toggle
between full map display, arrow
display (if route guidance active) and
split screen display, see "Information
on the display" below.
DEST button: open menu with
options for destination entry.
Eight-way switch: move display
window in navigation map view; to
select the destination, press in the
required direction to position the
crosswires over a destination on the
map.
RPT button: repeat last route
guidance message.
Activating the navigation system
Press the NAVI button.
36
Navigation
The map of the current location is
shown on the display, see
"Information on the display" below.
Information on the display
Route guidance not active
Route guidance messages
In addition to the visual instructions
on the display (see "Information on
the display" below), route guidance
messages will be announced when
route guidance is active.
Presetting the volume of route
guidance messages: see "Setting up
the navigation system" below.
Adjusting the volume of route
guidance messages while they are
announced: turn the X knob.
Repeating the last announced route
guidance message: press the RPT
button.
A compass symbol that indicates
the north direction.
If no GPS signal is available at the
current position, a crossed "GPS"
symbol is displayed below the
compass symbol.
The currently selected map scale
(change scale: turn multifunction
knob).
Note
To change to full map display: press
NAVI button.
If route guidance is not active, the
following information is displayed:
■ In the top line: time, street name of
current position, exterior
temperature.
■ Address and geographic
coordinates of current position.
■ Map display of the area around the
current position.
■ On the map: current position
marked by a red triangle.
Route guidance active
If route guidance is active, the
following information is displayed
(depending on the current Navigation
options settings, see chapter
"Guidance" 3 58):
Navigation
Information in the top line
■
■
■
■
Time
Distance to the final destination
Arrival time or travel time
Exterior temperature
Information on the arrow display
■ A big arrow representing the
direction to follow.
■ A small arrow representing the next
but one driving recommendation.
■ Distance to the next intersection.
■ Streets leading off the current
street to follow.
37
■ Below the arrow symbol: the name
of the current street to follow.
■ Above the arrow symbol: the name
of the street to follow after the next
intersection.
■ While driving on highways:
If the option Highway lane
guidance is activated in the Display
route guidance menu (see chapter
"Guidance" 3 58) the following
type of illustration is displayed:
Driving direction and distance to
the next highway exit, which you
need to follow.
Distances to the next service areas,
parking areas, intersections and/or
exits on the highway.
■ When reaching a highway
intersection information regarding
lane guidance is displayed:
38
Navigation
Information on the map display
On the right side of the display the
following information is shown:
■ A compass symbol that indicates
the north direction.
■ If no GPS signal (see chapter
"General information" 3 34) is
available at the current position: a
crossed "GPS" symbol is displayed
below the compass symbol.
■ The currently selected map scale
(change scale: turn multifunction
knob).
On the map the following information
is shown:
■ The route as a blue line.
■ The current position as a red
triangle.
■ The final destination as a
chequered flag.
■ Various symbols (see chapter
"Symbols overview" 3 68) that
indicate traffic information and
general information or points of
interest.
Setting up the navigation
system
Press the CONFIG button and then
select Navigation settings to open a
menu with navigation-specific
settings.
Navigation volume
The relative volumes of the
navigation message
(Announcement) and the audio
source (Background) during a
navigation message can be preset.
Navigation
Sort criteria
Select whether traffic messages are
to be displayed in an order based on
distance or street name.
Warning messages when route
guidance is inactive
Decide whether the Infotainment
system should announce warning
messages even if no route guidance
is active.
Delete lists
Set the desired values for
Announcement and Background.
To test the current settings: select
Volume test.
TMC settings
Select Infotypes to open a submenu
with various options to define whether
and which traffic message infotypes
are to be displayed on the active route
guidance map.
When User defined is selected, the
infotypes that are to be displayed can
be defined.
Select whether all entries in the
Address book or in the Last
destinations are to be deleted.
39
Import individual POIs
Only applicable if a USB drive with
points of interest (POI) data stored on
it is connected to the USB port 3 28
of the Infotainment system.
Importing POI data from a USB drive,
see "Exporting and importing POI
data" below.
Delete all imported POIs
Only applicable if POI data were
imported to the Infotainment system,
see "Exporting and importing POI
data" below.
Select this menu item to remove all
imported POI data from the myPOIs
memory of the Infotainment system.
Note
It is not possible to directly remove
individual imported points of interest
from the myPOIs memory.
If you want to remove individual
imported POIs: import updated POI
data to the Infotainment system that
do not contain the address data of
the regarding POIs.
40
Navigation
To remove all imported POIs of a
certain category: import an empty
POI data file of the regarding
category to the Infotainment system.
Export POIs
Exports all POI data stored in the
myPOIs memory of the Infotainment
system to a USB drive connected to
the USB port 3 28, see "Exporting and
importing POI data" below.
Delete Home address
Deletes the currently set home
address (displayed in the Enter
destination menu, see chapter
"Destination input" 3 44).
Exporting and importing POI
data
Introductory explanations
Types of POI data
The Infotainment system provides the
following types of points of interest
data:
■ Predefined Points of Interest stored
on the map SD card and indicated
by icons on the map display.
You can store such predefined
POIs in the address book or as
individual POIs in the myPOIs
memory of the Infotainment
system, see below.
■ Favourite destination addresses
that were stored in the Address
book.
You can export these address book
data to a USB drive for later use,
e.g., in other vehicles.
■ Individual POIs: favourite
destination addresses that were
stored in the myPOIs memory.
You can export these individual
POI data to a USB drive for later
use, e.g., in other vehicles.
■ User defined POIs: favourite
destination addresses that you
defined via GPS coordinates
(taken, e.g., from a topographical
map) and that you entered into text
files.
You can store these user defined
POI data on a USB drive and later
import the data to the myPOIs
memory of the Infotainment
system, see below.
■ Imported POIs: favourite
destination addresses that were
previously stored on a USB drive
and then imported to the myPOIs
memory of the Infotainment
system.
Advantages of POI export and import
The export and import of points of
interest data offer you, e.g., the
following advantages:
■ Define and store your favourite
destination addresses only once,
and later use these address data in
other vehicles.
See "Exporting and importing
individual POIs and address book
entries" below.
■ Define your favourite destination
addresses conveniently at home,
and later use them in your vehicle.
See "Creating and importing user
defined POIs" below.
■ Clearly arrange a large amount of
destination addresses, e.g.,
Navigation
favourite destination addresses of
other family members or
destination addresses for your next
journey or business trip in separate
submenus.
See "Organizing the POI data in
several subfolders" below.
Exporting and importing individual
POIs and address book entries
Brief description:
1. Connect a USB drive to the USB
port of your vehicle's Infotainment
system.
2. Store (export) your favourite
destination addresses on the USB
drive.
3. Connect the USB drive to the USB
port of a vehicle equipped with a
Navi 600 or Navi 900 system.
4. Download (import) the address
data to the vehicle's Infotainment
system.
After the import, the addresses can
be selected as destinations for route
guidance.
Detailed descriptions see below.
Exporting POI data to a USB drive
Connect a USB drive to the USB port
of the Infotainment system, see
chapter "USB port" 3 28.
Press the CONFIG button, select
Navigation settings and then select
Export POIs.
The Export POIs menu is displayed.
By default all individual POIs stored in
the myPOIs memory and all address
book entries will be exported.
If desired, deselect the address data
types that you do not want to be
exported.
41
Select Start export to store the
address data of the selected type(s)
on the connected USB drive.
The address data will be stored in a
folder named myPOIs that is located
in the root directory of the USB drive.
For each exported POI category, e.g.
Restaurant or Private, you will find a
correspondingly named file in that
folder.
Examples:
F:\myPOIs\Restaurant_3.poi or
F:\myPOIs\Private_1.poi, where F:\ is
the root directory of the USB drive.
Note
If files with POI data of the same
category are already stored on the
USB drive in the myPOIs folder,
these old file versions will be
overwritten by equally named new
file versions.
The folder myPOIs and the files with
POI data should not be renamed or
moved into another folder on the
USB drive. Otherwise the
Infotainment system will not be able
to import the address data again.
42
Navigation
Importing POI data from a USB drive
Connect a USB drive with POI data
stored on it (details see above) to the
USB port of the Infotainment system,
see chapter "USB port" 3 28.
To start the import: press the
CONFIG button, select Navigation
settings, select Import individual
POIs and then select Continue.
All POI data stored on the USB drive
is imported to the myPOIs memory of
the Infotainment system.
After the import is finished, the
imported POIs are selectable as
destinations via the Enter
destination menu, see chapter
"Destination input" 3 44.
Creating and importing user defined
POIs
User defined points of interest need
to be defined via GPS coordinates
that can be taken, e.g., from a
topographical map.
The GPS coordinates and further
address data need to be entered into
text files, each file representing a POI
category.
Brief description:
1. Create the text files for the POI
data.
2. Enter the desired address data
into the text files.
3. Store the text files with your POI
data on a USB drive.
4. Connect the USB drive to the USB
port of your vehicle's Infotainment
system.
5. Download (import) the text files
with your POI data to the
Infotainment system.
After the import, the addresses can
be selected as destinations for route
guidance.
Detailed descriptions see below.
Creating the text files for POI data
You can assign your favourite
destination addresses to 20 different
POI categories, with each POI
category assigned a number, see
"POI categories and assigned
numbers" below.
For each POI category you need to
create a separate text file.
The text files can be created, e.g., by
using a simple text editor software.
Note
The text editor must support the
UTF-8 character encoding for
Unicode.
Each text file name need to consist of
the category name, a single
underscore, the category's number
and the file extension .poi.
Example file names:
■ Business_2.poi
■ Home & Living_8.poi
■ Culture_15.poi
Note
The length of the text file names is
limited to 32 characters.
POI categories and assigned
numbers:
(1) Private, (2) Business, (3)
Restaurant, (4) Hotel, (5)
Automotive, (6) Travel, (7) Cinema,
(8) Home & Living, (9) Shopping, (10)
Craft, (11) Sport, (12) Sight, (13)
Navigation
Health care, (14) Leisure, (15)
Culture, (16) Nightlife, (17)
Communication, (18) News &
broking, (19) Government office, (20)
General.
Entering POI data into the text files
The image below shows a sample
text file named Home & Living_8.poi
with some sample POI data:
The POI data need to be entered into
the text files in the following format:
Longitude coordinate, Latitude
coordinate, "Name of POI", "Any
additional information", "Phone
number (optional)"
Example: 7.0350000, 50.6318040,
"Michaels Home", "Bonn - Hellweg 6",
"02379234567", see image above.
The GPS coordinates need to be
expressed in decimal degrees.
The maximum length of the POI name
is 60 characters. The same applies to
the additional information string and
the phone number string.
The POI data of each destination
address need to be entered in a single
separate line, see image above.
Storing the text files on a USB drive
The text files with POI data need to be
stored in a folder named myPOIs that
is located in the root directory of the
USB drive.
Example: F:\myPOIs\Home &
Living_8.poi, where F:\ is the root
directory of the USB drive.
After importing the individual POI
data to the Infotainment system (see
import description further below), the
Imported POIs menu will show a list
of selectable POI categories like the
following:
43
Organizing the POI data in several
subfolders
Optionally you can organize the text
files in several, arbitrary named,
subfolders.
Examples: F:\myPOIs\AnnsPOIs or
F:\myPOIs\MyJourney, where F:\ is
the root directory of the USB drive.
After importing individual POI data
organized in that way to the
Infotainment system (see import
description further below), the
Imported POIs menu will show a list
of selectable submenus like the
following:
44
Navigation
After the import is finished, the
imported POIs are selectable as
destinations via the Enter
destination menu, see chapter
"Destination input" below.
Destination input
■
Press the DEST button to open a
menu with various options for
entering or selecting a destination.
■
After selecting a submenu, the
related list of imported POI categories
will be displayed.
Importing the POI data to the
Infotainment system
Connect the USB drive with your
individual POI data to the USB port of
the Infotainment system, see chapter
"USB port" 3 28.
To start the import: press the
CONFIG button, select Navigation
settings, select Import individual
POIs and then select Continue.
All POI data stored on the USB drive
is imported to the myPOIs memory of
the Infotainment system.
■
■ Home: selection of the currently set
home address (if available).
Setting/changing the home
address, see "Setting the home
address" below.
■
After selecting the home address,
the Infotainment system
immediately calculates a route from
the current position to the home
address and then starts route
guidance.
Enter address: direct entry of a
destination address with country,
city, street and house number. See
"Entering an address directly"
below.
Address book: selection of a
destination address stored in the
address book. See "Selecting an
address from the address book"
below.
See also "Storing an address in the
address book or myPOIs memory"
and "Editing or deleting a stored
address" below.
Last destinations: selection from a
list of recently selected
destinations. See "Selecting a
previous destination" below.
myPOIs: selection of a destination
address stored in the myPOIs
memory. See "Selecting an
Navigation
address stored in the myPOIs
memory" below.
See also "Storing an address in the
address book or myPOIs memory"
and "Editing or deleting a stored
address" below.
■ Points of Interest: selection of POIs
(addresses of, e.g., restaurants,
petrol stations, hospitals etc.)
stored on the map SD card of the
Infotainment system. See
"Selecting a point of interest"
below.
■ Select from map: selection of a
destination from the map display
using the eight-way switch 3 6. See
"Selecting a destination from the
map" below.
■ Latitude / Longitude: selection of a
destination using geographic
coordinates. See "Selecting a
destination via geographic
coordinates" below.
45
Selecting a petrol station as
destination after a
Fuel level low alert
When the fuel level in the vehicle's
tank is low, an alert message is
displayed.
To start a search for petrol stations
close to the vehicle's current position:
select Petrol stations.
After the search is finished, a list of all
found petrol stations is displayed.
Below the list detailed information on
the currently marked petrol station is
displayed: the approximate direction
to the petrol station, the address, the
distance and the available fuel types
(in addition to Petrol and Diesel).
Abbreviations used for fuel types:
CNG (Compressed natural gas),
LPG (Liquefied petroleum gas).
Starting route guidance to a petrol
station
Select the desired petrol station.
The Navigation menu is displayed.
Select Start navigation to start route
guidance to the displayed address.
46
Navigation
Description on route guidance, see
chapter "Guidance" 3 58.
Entering an address directly
Press the DEST button and then
select Enter address to open the
menu shown below.
Select the desired country.
Entering an address using the speller
function
Mark the City: input field and then
press the multifunction knob to
activate the speller function.
To change/select the country: mark
the country input field (see image
above) and then press the
multifunction knob to open the
Countries menu.
Using the multifunction knob,
successively mark and accept the
letters for the desired city. During this
process the system will automatically
block letters that cannot occur next in
the city name.
The following symbols can be
selected in the bottom line:
⇧ : Lists with special letters are
displayed in the bottom line.
◀▶ : Previous/next letter is marked.
k : Delete last letter.
Aa : Upper, lower case.
Navigation
j : List function - once two letters
have been entered (in some cases
just one letter), all names available
with these letters are displayed. The
more letters are entered, the shorter
becomes the list.
OK : Complete entry or accept search
term.
By a long press on the BACK button
all letters entered are deleted at once
from the input line.
Repeat the process for the remaining
input fields (entering a house number
or junction is optional).
47
After completing the address, select
OK.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Selecting an address from the
address book
Press the DEST button and then
select Address book.
Select the desired address book
entry.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Selecting a previous destination
Press the DEST button and then
select Last destinations to open the
menu shown below.
48
Navigation
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Select the desired option. A menu
with various sorting options is
displayed.
Selecting an address stored in
the myPOIs memory
Press the DEST button and then
select myPOIs to open the menu
shown below.
A list of the most recently used
destination addresses is displayed.
Select the desired destination.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
Note
The option Imported POIs is only
selectable if points of interest
(address) data were downloaded
from a USB drive, see "Exporting
and importing POI data" in section
"Usage" above.
The sorting options determine in
which order the addresses of the
individual/imported points of interest
will be displayed later.
Select the desired sorting option.
A menu with the currently available
points of interest categories is
displayed.
Navigation
49
Selecting a point of interest
Press the DEST button and then
select Points of Interest.
A menu with various options for the
selection of points of interest (e.g.
restaurants, petrol stations, hospitals
etc.) is displayed.
Select the desired category.
A menu with a list of all available
points of interest of the selected
category (e.g. Restaurant) is
displayed.
Note
Points of interest which are far away
from the vehicle's current position
may not be displayed in the list.
Below the list detailed information on
the currently marked point of interest
is displayed: the approximate
direction to the point of interest, the
address and the distance.
Starting route guidance to a point of
interest
Select the desired point of interest.
The Navigation menu is displayed.
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Vicinity current position
Selection of points of interest close to
the vehicle's current position.
After selecting the option, a list of all
available points of interest categories
is displayed.
For example, you are looking for a
petrol station:
50
Navigation
Select Automotive & Petrol Stations.
A menu is displayed that provides
options for further refinement of the
petrol station search.
After selecting Start search, a search
for all petrol stations in the area is
started. The search takes into
account all petrol stations that meet
the currently set filter criteria for
Brand or chain name and Fueltype
(changing the filter criteria, see
"Setting filters for search refinement"
below).
After the search is finished, a list of all
found petrol stations is displayed.
Below the list detailed information on
the currently marked petrol station is
displayed: the approximate direction
to the petrol station, the address, the
distance and the available fuel types
(in addition to Petrol and Diesel).
Abbreviations used for fuel types:
CNG (Compressed natural gas),
LPG (Liquefied petroleum gas).
Setting filters for search refinement
After selecting Brand or chain name,
a list is displayed with all available
petrol station brands/chains in the
area.
The number of petrol stations can be
reduced by marking at least one
petrol station brand/chain.
After marking the desired brands/
chains: select Start search with
selected filters or, for further
refinement of the search, select
Continue with next filter (fuel types).
After selecting Fueltype, a list is
displayed with all fuel types available
(in addition to Petrol and Diesel) at
petrol stations in the area.
The number of petrol stations can be
reduced by marking at least one fuel
type.
Navigation
After marking the desired fuel types:
select Start search with selected
filters or, for further refinement of the
search, select Continue with next
filter (petrol station brands/chains).
After starting a search, a list of all
petrol stations that meet the
previously selected filter criteria is
displayed.
Along freeway
Selection of motorway related points
of interest (e.g. petrol stations or
service areas) along the route. Only
available when you are currently
driving on a motorway.
Selecting a point of interest: see
example above for "Vicinity current
position".
Select the desired petrol station.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Around destination
Selection of points of interest close to
the destination entered.
Selecting a point of interest: see
example above for "Vicinity current
position".
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Around other cities
Selection of points of interest around
any city.
After selecting the option, a country
list is displayed.
Select the desired country. A menu
for entering a city name is displayed.
51
Enter the desired city using the
speller function, see "Entering an
address using the speller function"
above.
Once the entry is specific enough, a
list with possible cities is displayed.
Sometimes it may be necessary to
select j to display the list.
Select the desired city. A menu
appears on which the points of
interest close to the selected city are
listed by category.
Selecting a point of interest: see
example above for "Vicinity current
position".
52
Navigation
Search by name
Selection of points of interest by
entering a name.
After selecting the option, a country
list is displayed.
Select the desired country. A menu
for name input is displayed.
Enter the name of the desired point of
interest using the speller function, see
"Entering an address using the
speller function" above.
Once the entry is specific enough, a
list with possible points of interest is
displayed. Sometimes it may be
necessary to select j to display the
list.
Select the desired point of interest.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Search by phone number
Selection of points of interest by
entering a telephone number.
After selecting the option, a country
list is displayed.
Select the desired country. A menu
for number input is displayed.
Enter the desired telephone number
using the speller function, see
"Entering an address using the
speller function" above.
Once the entry is specific enough a
list with possible telephone numbers
(each number representing a point of
interest) is displayed. Sometimes it
may be necessary to select j to
display the list.
Select the desired point of interest.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Navigation
53
Description on route guidance, see
chapter "Guidance" 3 58.
Description on route guidance, see
chapter "Guidance" 3 58.
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Selecting a destination from the
map
Selecting a destination via
geographic coordinates
Press the DEST button and then
select Select from map.
A menu with a map showing the area
around the current location is
displayed.
Note
The map scale can be changed by
turning the multifunction knob.
Using the eight-way switch on the
multifunction knob 3 6 position the
crosswire on a destination on the
map.
Press the multifunction knob to
confirm the selection.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Press the DEST button and then
select Latitude / Longitude.
A menu that allows the input of
geographic coordinates as
destination address is displayed.
54
Navigation
Entering the Longitude coordinate
1. Select Longitude.
2. Turn the multifunction knob to
select W or E (west or east of the
prime meridian in Greenwich).
3. Press the multifunction knob to
confirm the entry.
4. Enter and confirm the desired
values for the longitude degrees,
minutes and seconds.
Entering the Latitude coordinate
1. Select Latitude.
2. Turn the multifunction knob to
select N or S (north or south of the
equator).
3. Press the multifunction knob to
confirm the selection.
4. Turn the multifunction knob to
enter the desired degrees of
latitude.
5. Press the multifunction knob to
confirm the entry.
6. Enter the desired values for the
latitude minutes and seconds.
Select Apply to confirm the displayed
coordinates.
The Navigation menu is displayed.
Starting route guidance
Select Start navigation to start route
guidance to the displayed address.
Description on route guidance, see
chapter "Guidance" 3 58.
Storing the address
Select Store if you want to store the
displayed address in the address
book or myPOIs memory.
The Store menu is displayed, see
"Storing an address in the address
book or myPOIs memory" below.
Storing an address in the
address book or myPOIs
memory
The Infotainment system provides
two separate memory areas where
you can store your favourite
destination addresses: the address
book and the myPOIs memory.
Before storing an address in one of
these memory areas, you need to
assign the address to a category:
■ If you want to store an address in
the address book, you need to
assign the address to the
categories Private or Business.
■ If you want to store an address in
the myPOIs memory, you can
choose from 18 categories (e.g.
Restaurant, Travel or Culture).
Storing an address in the address
book
Press the DEST button to open the
Enter destination menu, and then
select an option for the input or
selection of a destination address
(e.g. Enter address or Last
Navigation
destinations), see regarding
descriptions on address input or
selection above.
After entering or selecting the desired
destination address, the Navigation
menu is displayed.
Select Store.
The menu Store is displayed, with the
previously entered or selected
destination address as default name.
The default name can be changed
(see example in the image below)
using the speller function, see
"Entering an address using the
speller function" above.
A telephone number can be entered
optionally.
The default category Private can be
changed to Business:
Select the displayed category to open
a menu with a list of all available
address categories.
Note
If you select another category than
Private or Business, the destination
address will be stored in the myPOIs
memory not in the address book.
Select Business.
The menu Store is displayed again.
55
Select OK to store the destination
address in the address book using the
displayed name and category.
A maximum of 100 destination
addresses can be stored in the
address book.
Storing an address in the myPOIs
memory
Storing a destination address in the
myPOIs memory functions the same
as described above for the address
book.
The only difference: select a category
different from Private or Business,
e.g. Restaurant, Automotive or
Shopping.
Note
If you select one of the categories
Private or Business, the destination
address will be stored in the address
book not in the myPOIs memory.
56
Navigation
Editing or deleting a stored
address
Address data (including the category
and telephone number) stored in the
address book or myPOIs memory can
be edited or entirely deleted at any
time.
Editing or deleting an address book
entry
Press the DEST button, select
Address book, select the desired
address entry and then select Edit.
The Edit menu is displayed.
The following options are available:
■ Address: opens the Enter address
menu. You can edit the displayed
address using the speller function,
see "Entering an address using the
speller function" above.
After confirming the edited address,
the Navigation menu is displayed
again.
If you want to edit also the name or
change the category, you need to
select the regarding address in the
address book again, see above.
■ Name & Number: after selecting
this option, you can edit the name
of the address book entry, edit the
telephone number or select a new
category, see "Storing an address
in the address book" above.
■ Delete: deletes the displayed
address from the address book.
■ Set as Home: sets the displayed
address as home address, see
"Setting the home address" below.
Editing or deleting a myPOIs entry
Press the DEST button and then
select myPOIs to open the menu
shown below.
Editing or deleting Individual POIs
Select Individual POIs, select the
desired sorting option (e.g. Vicinity
current position), select the desired
category (e.g. Restaurant), select the
desired address and then select Edit.
The Edit menu is displayed.
Editing or deleting the displayed
myPOIs entry functions the same as
described for an address book entry,
see above.
Navigation
Notes on Imported POIs
Imported points of interest (POIs
downloaded from a USB drive)
cannot be edited directly.
If you want to edit the address data of
an imported POI:
■ You first need to store the address
in the address book or as an
individual point of interest. Then
you can edit the address data of the
regarding address book entry or
myPOIs entry (selectable via
Individual POIs).
■ Or you can import updated address
data from a USB drive, see
"Exporting and importing POI data"
in chapter "Usage" above.
It is also not possible to directly
remove the address data of individual
imported points of interest from the
myPOIs memory.
If you want to remove individual
imported POIs:
Import updated POI data to the
Infotainment system that do not
contain the address data of the POIs
which you want to be removed.
To remove all imported POIs of a
certain category: import an empty POI
data file of the regarding category.
Descriptions on importing POI data,
see "Exporting and importing POI
data" in chapter "Usage" above.
Deleting all imported POIs at once:
Press the CONFIG button, select
Navigation settings and then select
Delete all imported POIs.
57
Setting a myPOIs entry as home
address
Press the DEST button and then
select myPOIs to open the menu
shown below.
Setting the home address
Before you can set an address as
home address, you need to store this
address in the address book or
myPOIs memory, see corresponding
descriptions above.
Setting an address book entry as
home address
Press the DEST button, select
Address book, select the desired
address entry, select Edit and then
select Set as Home.
The displayed address is set as new
home address and displayed as first
option in the Enter destination menu.
Setting an individual POI as home
address
Select Individual POIs, select the
desired sorting option (e.g. Vicinity
current position), select the desired
category (e.g. Restaurant), select the
desired address, select Edit and then
select Set as Home.
The displayed address is set as new
home address and displayed as first
option in the Enter destination menu.
58
Navigation
Notes on Imported POIs
Imported points of interest (POIs
downloaded from a USB drive)
cannot be set as home address
directly.
If you want to set the address of an
imported POI as home address:
You first need to store the address in
the address book or as an individual
point of interest.
Then you can set the address data of
the regarding address book entry or
myPOIs entry (selectable via
Individual POIs) as home address.
Functions with route guidance
inactive
Guidance
Start navigation
After selecting Start navigation the
menu shown below is displayed.
Press the NAVI button and then the
multifunction knob to display the
navigation main menu.
Depending on whether the route
guidance is currently inactive or
active, different menu options are
available.
The following options are available:
■ Start navigation: start route
guidance to the displayed address.
■ Show on map: show the location of
the displayed address on the map.
■ Call: not available.
■ Store: store the displayed address
in the address book or myPOIs
memory, see "Storing an address in
the address book or myPOIs
memory" in chapter "Destination
input" above.
Navigation
■ Edit: change/edit the displayed
address, see "Editing or deleting a
stored address" in chapter
"Destination input" above.
■ Route criteria: set/change criteria
for route calculation, see
"Navigation options" below.
TMC messages
Information on TMC, see chapter
"Dynamic guidance" 3 34.
Select TMC messages to display a list
of all TMC traffic messages that are
currently received.
Select a TMC traffic message to
display detailed information on the
related traffic issue.
59
Route criteria
Navigation options
The corresponding menu provides
options and a multitude of relating
submenus for route guidance
configuration.
The calculation of the route can be
controlled by various criteria.
Select one of the following criteria:
■ Fastest
■ Shortest
■ Economic: an energy-optimized
route is calculated, taking into
account the vehicle-specific
parameters that are currently set in
the Vehicle parameters menu, see
below.
Select Vehicle parameters to open a
menu for the selection of vehiclespecific parameters.
60
Navigation
The selected settings will be taken
into account for route calculation, if
Economic is currently selected, see
above.
After setting the desired vehicle
parameters, press the BACK button
to leave the menu.
Select Dynamic guidance to open a
menu for the configuration of dynamic
route guidance.
Information on dynamic route
guidance, see chapter "Dynamic
guidance" 3 65.
Select Dynamic guidance to activate/
deactivate dynamic route guidance.
If dynamic route guidance is
activated:
Select Automatic recalculation if you
want the route be recalculated
automatically when there are traffic
problems.
Select Recalculation after
confirmation if you want the route be
recalculated only after confirming the
corresponding message.
Select Apply settings to activate the
displayed settings and to leave the
menu.
If desired select one or several of the
following options in the Route
criteria menu:
■ Avoid freeways
■ Avoid toll roads
■ Avoid tunnels
■ Avoid ferries
■ Consider time restricted roads
Display route guidance
The following options are available for
the display of route guidance:
Navigation
61
Using the Popup information option,
you can select whether route
guidance information from the
navigation should be displayed in
pop-up windows in other operating
modes (e.g. radio). The information is
hidden after a set time or by pressing
the BACK button.
Select Apply settings to activate the
displayed settings and to return to the
Navigation options menu.
Using the Highway lane guidance
option, you can determine which type
of illustration should be displayed
when reaching a highway
intersection.
If Highway lane guidance is
deactivated the following type of
illustration will be displayed:
If Highway lane guidance is activated
the following type of illustration will be
displayed:
Map options
Select Map options and then Map
mode to display the following
submenu:
62
Navigation
Select between map orientation north
up and head up on the map display.
Select Map options and then Show
POIs on map to open a submenu with
various options to define whether and
which points of interest should be
displayed on the map.
When User defined is selected the
type of points of interest can be
defined that should be displayed,
e.g. restaurant, hotel, public places,
etc.
Display of arrival time or driving time
After selecting the option Indication
estimated driving time or Indication
estimated arrival time in the menu
Navigation options, the
corresponding time is shown in the
top line on the route guidance screen.
Current position information
The following information on the
current position is displayed:
■ City
■ Street name
■ Latitude
■ Longitude
■ Map display
Functions for active route
guidance
The current position can be copied to
the address book or myPOIs memory
using Store, see "Storing an address
in the address book or myPOIs
memory" in chapter "Destination
input" above.
Stop navigation
After selecting Stop navigation, the
route guidance is deactivated and the
menu options for route guidance
inactive are displayed, see
"Functions with route guidance
inactive" above.
Destination information
Displayed information: same as on
the display for Current position.
TMC messages
Information on TMC, see chapter
"Dynamic guidance" 3 34.
After selecting TMC messages the
Filtering menu is displayed.
Navigation
Select whether All traffic messages or
only Traffic messages along route
should be displayed in the TMC
messages list, see below.
Navigation options
Description, see "Functions with
route guidance inactive" above.
Route information
The following information can be
accessed on the Route information
menu:
■ Route list
■ Current position information
■ Destination information
■ Overview current route
Route list
All streets on the calculated route are
listed with the related distances.
Route list items marked with a "+"
symbol can be expanded by selecting
the related list item. After selection,
further details on the related list item
are displayed.
Current position information
Description, see "Functions with
route guidance inactive" above.
Destination information
Description, see "Functions with
route guidance inactive" above.
Overview current route
The following information on the
current route is displayed:
■
■
■
■
■
Position
Destination
Arrival time
Distance
Map display
63
64
Navigation
Route blocking
The following options are available to
manually exclude certain areas/route
sections from the route guidance:
Route list
In the list of street names on the
currently calculated route, streets can
be excluded from the route guidance.
By distance
By setting a distance the section of
route from the current position to the
set distance can be excluded from the
route guidance.
To exclude a street from the route
guidance:
Mark the regarding street name and
press the multifunction knob. The
street name is displayed crossed-out.
If desired, exclude further streets from
the route guidance.
Select Apply settings and confirm the
displayed message.
The route is re-calculated, taking into
account the excluded streets.
Set the desired distance, press the
multifunction knob and then confirm
the displayed message.
The route is re-calculated taking into
account the excluded route section.
Note
The route blocking entered remains
active until a new route calculation is
performed.
Navigation
Remove all route blockages
After selecting this option, all areas/
route sections previously selected as
to be excluded from the route
guidance will be taken into account
again for route guidance.
Dynamic guidance
If dynamic route guidance is active,
the entire current traffic situation that
the Infotainment system receives via
TMC is included in the calculation of
the route. The route is suggested
taking into account all traffic problems
or restrictions as per pre-set criteria
(e.g. "shortest route", "avoid
freeways" etc.).
In the case of a traffic problem (e.g.
traffic jam, closed road) on the route
driven, a message is displayed and a
voice message output indicating the
nature of the problem. The driver can
decide whether to drive around the
traffic problem taking the suggested
change to the route or to carry on
through the traffic problem.
Nearby traffic problems are also
reported if route guidance is not
active.
If route guidance is active, the system
continuously checks, based on the
traffic information, whether it would
be better to recalculate the route or
take an alternative route taking into
account the current traffic situation.
The activation and deactivation of
dynamic route guidance, as well as
criteria for the calculation of the route
and other settings for navigation, are
made in the Navigation options menu,
see chapter "Guidance" 3 58.
65
Dynamic route guidance only works if
traffic information is received via the
RDS-TMC traffic information system.
The possible delay due to a traffic
problem calculated by the
Infotainment system is based on data
that the system receives via the RDSTMC station currently set. The actual
delay may be different to that
calculated.
Maps
All map data required for use of the
navigation system is stored on an SD
card provided with the Infotainment
system.
Map SD card
The SD card reader of the
Infotainment system can only read
the SD card provided specifically for
use with the vehicle's navigation
system. The SD card reader cannot
read any other SD cards.
Due to production date of the map
data on the SD card, some new roads
may not be included, or some names
66
Navigation
and roads may differ from those in
use at the time the map data was
produced.
To order additional SD cards or an
update of the map data, contact a
Vauxhall Authorised Repairer.
Replacing a map SD card, see below .
Important information on SD card
handling
Caution
Never attempt to use an SD card
that has been cracked, deformed
or repaired using adhesive tape.
Doing so may damage the
equipment.
■ Handle the SD card with care.
Never touch the metal contacts.
■ Do not use any conventional
cleaner, benzine, thinner, or
antistatic spray.
■ If you need to clean the SD card,
use a soft cloth.
■ Do not bend the SD card. Do not
use any SD card that is bent or
cracked.
■ Do not put any sticker or write
anything on either surface.
■ Do not store the SD card in
locations exposed to direct
sunlight, or in high temperatures or
humidity.
■ Always place the SD card in its
storage case, when not in use.
Removing the SD card
Replacing a map SD card
The SD card slot is located in the
centre console in front of the
gearshift.
Press on the inserted SD card to
unlock it, and then carefully pull the
SD card out of the SD card slot.
Navigation
Inserting the SD card
Push the SD card with the cut-out
edge on the left side (see image
above) carefully into the SD card slot
until the card engages.
Note
The SD card and SD card slot must
always be kept clean and dry.
67
68
Navigation
Symbols overview
Navigation
No. Explanation
No. Explanation
1
Current position (map)
18
Closed list
2
Destination
19
Shopping centre
3
Current position (route list)
20
Toll road
4
not available
21
Tourist information
5
not available
22
Sight
6
Fog
23
Sport & leisure
7
Road works
24
Going out
8
Slippery road
25
Museum
9
Smog
26
Car rental
10
Snow
27
Travel information
11
Storm
28
Leisure activity
12
Caution/warning
29
Provision of services
13
Closed road
30
Cash machine
14
Dense traffic
31
Bus station
15
Traffic jam
32
Camp site
16
Narrow lanes
17
Open list
69
70
Navigation
Navigation
No.
Explanation
No.
Explanation
33
Chemist
50
Petrol station
34
Cinema
51
Service area
35
Airport
52
Restaurant
36
Amusement park
53
WC
37
City
54
Historical monument
38
Bank
55
Hospital
39
Traffic message
56
Emergency
40
Ferry
57
Police
41
Border
58
Harbour
42
Tunnel
59
Mountain pass
43
Kiosk
60
Public place
44
Grocery
61
Related to the car
45
Hotel/motel
62
Garage
46
Motorway exit
63
Cemetery
47
Car park
48
Park & ride
49
Multi-storey car park
71
72
Speech recognition
Speech recognition
General information ..................... 72
Phone control ............................... 73
General information
The speech recognition of the
Infotainment system enables you to
operate various functions of the
phone portal via voice input. It
recognises commands and numeric
sequences independently of the
relevant speaker. The commands
and numeric sequences can be
spoken without a voice pause
between the individual words.
You can also save telephone
numbers assigning a name of your
choice (voice tag). Using these
names, you can later set up a
telephone connection.
In the event of incorrect operation or
commands the speech recognition
gives you acoustic feedback and
requests you to re-enter the desired
command. Apart from this, the
speech recognition acknowledges
important commands and will enquire
if necessary.
To ensure that conversations inside
the vehicle do not lead to
unintentional triggering of system
functions, the speech recognition
does not start until it has been
activated.
Important notes on language
support
■ Not all languages available for the
display of the Infotainment system
are also available for the speech
recognition.
■ If the currently selected language
for the display is not supported by
the speech recognition, you need to
enter the voice commands in
English.
To be able to enter voice
commands in English, you first
need to activate the phone main
menu by pressing the PHONE
button on the Infotainment system,
and then activate the speech
recognition of the phone portal by
pressing the button w on the
steering wheel.
Speech recognition
Phone control
Activating speech recognition
To activate the speech recognition of
the Phone portal, press the button w
on the steering wheel. For the
duration of the dialogue any active
audio source is muted and any traffic
news fade-in is cancelled.
Adjusting the volume for voice
output
Turn the volume knob on the
Infotainment system, or press the
+ or ― button on the steering wheel.
Cancelling a dialogue
There are various possibilities of
deactivating the speech recognition
and cancelling the dialogue:
■ Press the button x on the steering
wheel.
■ Say "Cancel".
■ Do not enter (say) any commands
for some time.
■ After the third unrecognised
command.
Operation
With the aid of the speech recognition
the mobile phone can be operated
very conveniently via voice input. It is
sufficient to activate the speech
recognition and to enter (say) the
desired command. After input of the
command the Infotainment system
guides you through the dialogue with
appropriate questions and feedback
to achieve the desired action.
Main commands
After activation of the speech
recognition a short tone signals that
the speech recognition is expecting
input.
Main commands available:
■ "Dial"
■ "Call"
■ "Redialing"
■ "Save"
■ "Delete"
■ "Directory"
■ "Pair"
73
■ "Select device"
■ "Voice feedback"
Commands that are frequently
available
■ "Help": the dialogue is terminated
and all commands available within
the actual function are enumerated.
■ "Cancel": the speech recognition is
deactivated.
■ "Yes": a suitable action is triggered
depending on the context.
■ "No": a suitable action is triggered
depending on the context.
Entering a telephone number
After the command "Dial" the speech
recognition requests input of a
number.
The telephone number must be
spoken in your normal voice without
any artificial pauses between the
individual numbers.
Recognition works best, if a pause of
at least half a second is made after
every three to five digits. The
Infotainment system then repeats the
numbers recognised.
74
Speech recognition
You can then enter further numbers
or the following commands:
■ "Dial": the inputs are accepted.
■ "Delete": the number last entered or
the block of numbers last entered is
deleted.
■ "Plus": a preceding "+" is entered
for a call abroad.
■ "Verify": the inputs are repeated by
the voice output.
■ "Asterisk": An asterisk "*" is
entered.
■ "Hash": A hash "#" is entered.
■ "Help"
■ "Cancel"
The maximum length of the telephone
number entered is 25 digits.
To be able to make a call abroad you
can say the word "Plus" (+) at the
beginning of your number. The plus
allows you to call from any country
without knowing the prefix for calls
made abroad in that country. Then
say the required country code.
Example of a dialogue
User: "Dial"
Voice output: "Please, say the
number to dial"
User: "Plus Four Nine"
Voice output: "Plus Four Nine"
User: "Seven Three One"
Voice output: "Seven Three One"
User: "One One Nine Nine"
Voice output: "One One Nine Nine"
User: "Dial"
Voice output: "The number is being
dialled"
Entering a name
Using the "Call" command a
telephone number is entered that has
been stored in the telephone book
under a name (voice tag).
Commands available:
■ "Yes"
■ "No"
■ "Help"
■ "Cancel"
Example of a dialogue
User: "Call"
Voice output: "Please, say the
nametag to call"
User: <Name>
Voice output: "Do you want to call
<Michael>?"
User: "Yes"
Voice output: "The number is being
dialled"
Starting a second call
A second call can be started during an
active telephone call. To do so, press
the button w.
Commands available:
■ "Send": activate manual DTMF
(touch-tone dialling), e.g. for voice
mail or telephone banking.
■ "Send nametag": activate DTMF
(touch-tone dialling) by entering a
name (voice tag).
■ "Dial"
■ "Call"
■ "Redialing"
■ "Help"
■ "Cancel"
Speech recognition
Example of a dialogue
User: <if a telephone call is active:
press the w button>
User: "Send"
Voice output: "Please, say the
number to send."
(for number input see the dialogue
example for Entering a telephone
number)
User: "Send"
Redialing
The number last dialled is redialled
with the command "Redialing".
Saving
With the command "Save" a
telephone number is stored in the
telephone book under a name (voice
tag).
The name entered must be repeated
once. The pitch and pronunciation
must be as identical as possible for
both name inputs, otherwise the
speech recognition will reject the
inputs.
A maximum of 50 voice tags can be
stored in the telephone book.
Voice tags are speaker-dependent,
i.e. only the person who recorded a
voice tag can open it.
To avoid the start of the recording of
a saved name from being cut-off, a
short pause should be left after an
input request.
To be able to use the voice tag
independently of the location, i.e.
including other countries, all
telephone numbers should be
entered with a "plus" character and a
country code.
Commands available:
■ "Save": the inputs are accepted.
■ "Verify": the last input is repeated.
■ "Help"
■ "Cancel"
Example of a dialogue
User: "Save"
Voice output: "Please, say the
number to save"
(for number input see the dialogue
example for Entering a telephone
number)
User: "Save"
75
Voice output: "Please, say the
nametag to save"
User: <Name>
Voice output: "Please, repeat the
nametag to confirm"
User: <Name>
Voice output: "Saving the nametag"
Deleting
A previously saved voice tag is
deleted with the command "Delete".
Commands available:
■ "Yes"
■ "No"
■ "Help"
■ "Cancel"
Listening to stored names
The voice output of all stored names
(voice tags) is started with the
command "Directory".
76
Speech recognition
Commands available during voice
output of the voice tags:
■ "Call": the telephone number of the
voice tag last read aloud is
selected.
■ "Delete": the entry of the voice tag
last read aloud is deleted.
Saving a mobile phone to or deleting
it from the device list
With the command "Pair" a mobile
phone can be saved to or deleted
from the device list of the Phone
portal 3 78.
Commands available:
■ "Add"
■ "Delete"
■ "Help"
■ "Cancel"
Example of a dialogue
User: "Pair"
Voice output: "Do you want to add or
delete a device?"
User: "Add"
Voice output: "Using the pair function
in the external device, enter <1234>
to pair."
Voice output: "Do you want to pair the
device?"
User: "Yes"
Voice output: "The device is
connected as the number
<device_number>"
Selecting a mobile phone from the
device list
Using the "Select device" command,
a mobile phone can be selected in the
device list for setting up a Bluetooth
connection.
Example of a dialogue
User: "Select device"
Voice output: "Please, say a device
number to select"
User: <device_number>
Voice output: "Do you want to select
the device number <device_num‐
ber>?"
User: "Yes"
Voice output: "Do you want to pair the
device?"
User: "Yes"
Voice output: "One moment. The
system searches for the selected
device"
Voice output: "Device number
<dev_num> is selected"
Voice feedback
Each voice input is answered or
commented on by the Infotainment
system by way of a voice output that
is adapted to the situation.
To switch the voice output on or off,
enter "Voice feedback" or press the
button w.
Phone
Phone
General information ..................... 77
Bluetooth connection ................... 78
Emergency call ............................ 83
Operation ..................................... 84
Mobile phones and CB radio
equipment .................................... 87
General information
The Phone portal provides you with
the possibility of having mobile phone
conversations via a vehicle
microphone and the vehicle
loudspeakers as well as operating the
most important mobile phone
functions via the Infotainment system
in the vehicle. To be able to use the
Phone portal, the mobile phone has
to be connected with it via Bluetooth.
The Phone portal can be operated
optionally via the speech recognition
system.
Not all Phone portal functions are
supported by every mobile phone.
The possible phone functions depend
on the relevant mobile phone and
network provider. You will find further
information on this in the operating
instructions for your mobile phone or
you can enquire about them with your
network provider.
77
Important information for
operation and traffic safety
9 Warning
Mobile phones have effects on
your environment. For this reason
safety regulations and directions
have been prepared. You should
be familiar with the related
directions before you use the
telephone function.
9 Warning
Use of the hands-free facility while
driving can be dangerous because
your concentration is reduced
when telephoning. Park your
vehicle before you use the handsfree facility. Follow the stipulations
of the country in which you find
yourself at present.
Do not forget to follow the special
regulations that apply in specific
areas and always switch off the
mobile phone if the use of mobile
78
Phone
phones is prohibited, if
interference is caused by the
mobile phone or if dangerous
situations can occur.
EU R & TTE Compliance
Bluetooth
The Phone portal supports Bluetooth
Handsfree Profile V. 1.5 and is
specified in accordance with the
Bluetooth Special Interest Group
(SIG).
You will find further information about
the specification on the Internet at
http://www.bluetooth.com.
Additionally, the Phone portal
supports SIM Access Profile (SAP).
Hereby, we declare that the Bluetooth
System Transceiver is in compliance
with the essential requirements and
other relevant provisions of Directive
1999/5/EC.
Operating the speech
recognition
Do not use the speech recognition in
emergencies, because in stress
situations your voice can change so
much that it can no longer be
recognised sufficiently to set up the
desired connection quickly enough.
Control elements
The most important telephone
specific control elements are as
follows:
PHONE button: opens the telephone
main menu.
Controls on steering wheel:
q, w: take call, activate speech
recognition.
n, x: end/reject call, deactivate
speech recognition.
The Phone portal can be operated
optionally via speech recognition
3 72.
Bluetooth connection
Bluetooth is a radio standard for the
wireless connection of, for example, a
telephone with other devices.
Information such as a telephone
book, call lists, the network operator’s
name and field strength can be
transferred. The functionality can be
restricted depending on the
telephone type.
Phone
To be able to set up a Bluetooth
connection with the Phone portal, the
Bluetooth function of the mobile
phone has to be activated and the
mobile phone must be set to "visible".
For further information please refer to
the operating instructions for the
mobile phone.
Bluetooth menu
Press CONFIG button.
Select Phone settings and then
Bluetooth.
Activating Bluetooth
If the Bluetooth function of the Phone
portal is deactivated:
Set Activation to On and confirm the
subsequent message.
Device list
When a mobile phone is connected to
the Phone portal via Bluetooth for the
first time, the mobile phone is saved
in the device list.
A maximum of 5 mobile phones can
be saved in the device list.
79
Connecting a mobile phone for
the first time
There are two options for connecting
a mobile phone to the Phone portal:
by adding it as a handsfree device or
by using the SIM Access Profile
(SAP).
Handsfree mode
When the mobile phone is added as
a handsfree device the user can
make or receive calls and use other
functions via the Phone portal. The
range of functions available depends
on the mobile phone. While it is
connected with the Phone portal the
mobile phone can be operated as
usual.
Note that the mobile phone battery
may discharge at a higher speed than
usual due to the Bluetooth connection
active along with normal operation of
the mobile phone.
SAP mode
When using the SAP option, a wider
range of functions is available via the
Phone portal such as various security
and messaging options. The actual
80
Phone
range of functions depends on the
network provider. Additionally, in the
SAP mode the mobile phone is in the
standby mode. Only the Bluetooth
connection and the SIM card are
active, which leads to lower energy
consumption of the connected mobile
phone.
As soon as the mobile phone has
detected the Phone portal the
Bluetooth code can be entered on the
mobile phone.
can be changed at any time. For
security reasons a four-digit and
randomly selected code must be
used for pairing devices.
As soon as the Phone portal has
detected the mobile phone, the
connection set-up can be confirmed.
The mobile phone is adopted in the
device list and can be operated via
the Phone portal.
Select Change Bluetooth code. On
the menu displayed, edit the actual
Bluetooth code and accept the
modified code using OK.
Connecting a mobile phone as a
handsfree device
Select Add device (Handsfree). The
Bluetooth code to be entered into the
mobile phone is displayed.
The Phone portal can now be
detected by other Bluetooth devices.
Changing the Bluetooth code
(only relevant for handsfree mode)
The first time a Bluetooth connection
to the Phone portal is set up, a default
code is displayed. This default code
Connecting a mobile phone via SIM
Access Profile (SAP)
Select Add SIM access device
(SAP). The mobile portal scans for
available devices and displays a list
of devices found.
Phone
81
Note
The mobile phone must have
Bluetooth activated and be set to
visible.
Select the desired mobile phone from
the list. The SAP passcode prompt is
shown on the Infotainment display
containing a 16-digit code.
Enter the displayed SAP passcode in
the mobile phone (without spaces).
The mobile phone PIN code is shown
on the Infotainment display.
If the PIN request function is active,
the user will have to enter the PIN
code of the SIM card in the mobile
phone.
Enter the PIN code of the mobile
phone SIM. The mobile phone is
paired with the Phone portal.
Services of the mobile network
provider can be used via the Phone
portal.
82
Phone
Connecting a mobile phone saved in
the device list
Select the desired mobile phone and
then select the option Select in the
menu displayed.
As soon as the Phone portal has
detected the mobile phone, the
connection setup can be confirmed.
The mobile phone can be operated
via the Phone portal.
Removing a mobile phone from the
device list
Select the desired mobile phone from
the device list. In the menu displayed
select Delete and confirm the
subsequent message.
Adjusting the ring tone
To change the ring tone
characteristic:
Press CONFIG button.
Select Phone settings and then
Ringtone.
Select the desired option.
To change the ring tone volume:
While the phone rings turn the m knob
of the Infotainment system or press
the buttons + / - on the steering wheel.
Setting up a connected phone
Various mobile phone settings can be
configured in the Phone settings
menu, if the phone is connected via
SAP.
Changing security settings
Press CONFIG button.
Select Phone settings and then
Security.
The security dialogue is displayed.
Activating/Deactivating PIN request
Select PIN request On or Off.
Enter the PIN code of the mobile
phone SIM card and confirm.
Note
This option depends on the
individual network provider.
Changing the PIN code
Select Change PIN.
Enter the current PIN code. Enter the
new PIN code. Repeat the new PIN
code and confirm. The PIN has been
changed.
Configuring network services
Select Phone settings and then
Network services. The Network
services dialogue is displayed.
Depending on the network provider
and the mobile phone several options
are available.
Phone
■ Network selection: choose
between automatic or manual
network selection.
■ Call waiting: activate or deactivate
call waiting.
■ Call diverting: select diverting
options depending on the situation.
■ Call barring: configure call barring
options depending on the situation.
For details on network services
configuration refer to the mobile
phone manual or enquire with the
mobile network provider.
Configuring SMS centre number
The SMS centre number is a phone
number that acts as a gateway for
transferring SMS messages between
mobile phones. This number is
usually preset by the network
provider.
To configure the SMS centre number
select Phone settings and then SMS
center number. If required, modify the
SMS centre number.
Resetting the mobile phone to factory
settings
Select Phone settings and then
Factory settings.
Emergency call
9 Warning
Connection setup cannot be
guaranteed in all situations. For
this reason you should not rely
exclusively on a mobile phone
when a vitally important
communication (e. g. a medical
emergency) is concerned.
In some networks it may be
necessary for a valid SIM card to
be properly inserted in the mobile
phone.
9 Warning
Bear in mind that you can make
and receive calls with the mobile
phone, if it is in a service area with
a sufficiently strong signal. Under
83
certain circumstances emergency
calls cannot be made on all mobile
phone networks; it is possible that
they cannot be made when certain
network services and/or telephone
functions are active. You can
enquire about this with the local
network operators.
The emergency call number can
differ depending on the region and
country. Please enquire
beforehand about the correct
emergency call number for the
relevant region.
Making an emergency call
Dial the emergency call number (e.g.
112).
The telephone connection to the
emergency call centre is set up.
Answer when the service personnel
questions you about the emergency.
84
Phone
9 Warning
Do not end the call until you are
requested to do so by the
emergency call centre.
Operation
Introduction
As soon as a connection via
Bluetooth has been set up between
your mobile phone and the
Infotainment system, you can also
operate many functions of your
mobile phone via the Infotainment
system.
Via the Infotainment system, you can,
e.g., set up a connection to the
telephone numbers stored in your
mobile phone or change the
telephone numbers.
Note
In the handsfree mode mobile phone
operation continues to be possible,
e. g. taking a call or adjusting the
volume.
After setup of a connection between
the mobile phone and the
Infotainment system the mobile
phone data is transmitted to the
Infotainment system. This can take
some time depending on the phone
model. During this period operation of
the mobile phone is possible via the
Infotainment system only to a limited
extent.
Not every telephone supports all
functions of the Phone portal.
Therefore deviations from the range
of functions described with these
specific telephones are possible.
Setting the volume for handsfree facility
Turn the m knob of the Infotainment
system or press the buttons + / - on
the steering wheel.
Dialling a telephone number
With the telephone main menu active,
press the multifunction knob to open
the Phone menu.
Several options for dialling telephone
numbers, for using the phone book
and call lists, for viewing and editing
messages are available.
Using the Phone off command the
connected phone can be detached
from the Phone portal.
Phone
Entering a number manually
85
If the SIM card or telephone are
different, the telephone book is
reloaded. This process can take a few
minutes depending on the phone
model.
Selecting a telephone number from
the telephone book
Note
Telephone book entries are carried
over as they are transferred from the
mobile phone. The presentation and
order of the telephone book entries
may be different on the Infotainment
system's display and the mobile
phone's display.
Select Enter number, then enter the
desired number sequence.
To start the dialling process, select y.
To open the telephone book menu,
select z.
Telephone book
After setting up the connection the
telephone book is compared with the
telephone book in the temporary
memory, provided that the same SIM
card or same telephone is concerned.
During this period any newly added
entries are not displayed.
Select Phone book.
On the Search menu displayed,
select the desired first letter range to
start a preselection of the telephone
book entries that you want to have
displayed.
After having performed the
preselection: select the desired entry
in the telephone book to display the
numbers saved under this entry.
Select the desired number to start the
dialling process.
86
Phone
Call lists
Messaging functions
Incoming call
When there is an incoming call a
menu is displayed for you to accept or
decline the telephone call.
Select the required option.
Functions during a telephone
call
Via the menu Call lists the incoming,
outgoing and missed calls can be
viewed and the relevant numbers can
be dialled. The lists can also be
deleted in this menu.
To start a dialling process: select the
desired call list, an entry in the call list
and finally the desired telephone
number.
When the mobile phone is paired
using the SAP mode, messages can
be viewed, composed and sent via
the Phone portal. The messages can
also be deleted in this menu.
To view received messages: select
Inbox.
To view sent messages: select
Outbox.
To compose a message: select Write
new message.
Note
Messages are limited to 70
characters.
If you are currently making a
telephone call, press the multifunction
knob to open a submenu.
Various options are available
depending on the situation and range
of functions of the mobile phone:
■ Hang up: disconnect the telephone
connection.
■ Call number: enter a telephone
number to make a second
telephone call or perform DTMF
(touch-tone dialling), e.g. for voice
mail or telephone banking.
■ Detach call: detach the connection
to a conference participant in a
telephone conference.
■ Merge calls: merge two calls when
there are several active calls.
Phone
■ Switch calls: switch between calls,
if there are several calls.
■ Mute call: mute a call.
Note
If the ignition is turned off during a
telephone call the connection
remains active until the telephone
call is terminated.
Mobile phones and CB
radio equipment
Installation instructions and
operating guidelines
The vehicle specific installation
instructions and the operating
guidelines of the mobile phone and
handsfree manufacturer must be
observed when installing and
operating a mobile telephone. Failure
to do so could invalidate the vehicle
type approval (EU directive 95/54/
EC).
Recommendations for fault-free
operation:
■ Professionally installed exterior
antenna to obtain the maximum
range possible,
■ Maximum transmission power
10 watts,
■ Installation of the phone in a
suitable spot, consider relevant
Note in the Owner's manual,
chapter Airbag system.
Seek advice on predetermined
installation points for the external
antenna or equipment holder and
ways of using devices with a
transmission power exceeding
10 watts.
Use of a handsfree attachment
without external antenna with mobile
telephone standards GSM
900/1800/1900 and UMTS is only
permitted if the maximum
transmission power of the mobile
telephone is 2 watts for GSM 900 or
1 watt for the other types.
87
For reasons of safety, do not use the
phone while driving. Even use of a
handsfree set can be a distraction
while driving.
9 Warning
Operation of radio equipment and
mobile telephones which fail to
meet above mentioned mobile
telephone standards is only
permitted using an antenna
located outside of the vehicle.
Caution
Mobile telephones and radio
equipment may lead to
malfunctions in the vehicle
electronics when operated inside
the vehicle with no exterior
antenna, unless the above
mentioned regulations are
observed.
88
Index
A
Activating CD player..................... 25
Activating speech recognition....... 73
Activating the navigation system. . 35
Activating the radio....................... 15
Address book................................ 44
Address input................................ 44
Autostore lists............................... 16
B
BACK button................................. 10
Basic operation............................. 10
Bluetooth...................................... 77
Bluetooth connection.................... 78
C
CD player
activating................................... 25
important information................ 24
usage........................................ 25
Configuring DAB........................... 22
Configuring RDS........................... 20
Control elements overview............. 6
D
DAB.............................................. 22
Destination input .......................... 44
Digital audio broadcasting............ 22
Dynamic guidance........................ 65
E
Emergency call............................. 83
Enhanced Other Networks........... 20
EON.............................................. 20
F
Favourite lists............................... 16
G
General information...................
.......... 4, 24, 27, 28, 31, 34, 72, 77
Guidance ..................................... 58
H
Handsfree mode........................... 78
Home address.............................. 35
I
Individual POIs............................. 35
Infotainment system
maximum startup volume.......... 14
speed dependent volume.......... 14
tone settings.............................. 12
volume of the traffic
announcements........................ 14
volume settings......................... 14
89
M
Maps ............................................ 65
Map SD card
handling..................................... 65
replace...................................... 65
Menu operation............................. 10
Mobile phones and CB radio
equipment ................................ 87
Multifunction knob......................... 10
Mute................................................ 9
myPOIs......................................... 44
N
Navigation
activating................................... 35
Address book............................ 44
control elements........................ 35
deleting Home address............. 35
deleting imported POIs............. 35
destination input........................ 44
dynamic guidance............... 58, 65
fuel level low alert...................... 44
functioning................................. 34
highway lane guidance............. 58
Home address........................... 44
importing/exporting POIs........... 35
map SD card............................. 65
myPOIs..................................... 44
navigation display..................... 35
navigation options..................... 58
navigation volume..................... 35
Points of Interest....................... 44
repeat last navigation message 58
route blocking............................ 58
route guidance.......................... 58
route list..................................... 58
start navigation.......................... 58
symbols overview...................... 68
TMC messages......................... 58
usage........................................ 35
using the speller function.......... 44
Navigation display........................ 35
Navigation volume........................ 35
O
Operation...................................... 84
P
Phone
adjusting ring tones................... 78
Bluetooth................................... 77
Bluetooth connection................ 78
call lists...................................... 84
control elements........................ 77
dialling a number....................... 84
emergency calls........................ 83
functions during a call............... 84
handsfree mode........................ 78
important information................ 77
messaging functions................. 84
recharging the battery............... 77
setting the volume..................... 84
SIM Access Profile (SAP)......... 78
telephone book......................... 84
Phone control............................... 73
Playing saved audio files.............. 29
R
Radio
Radio data system (RDS)......... 20
activating................................... 15
autostore lists............................ 16
Digital audio broadcasting
(DAB)........................................ 22
favourite lists............................. 16
selecting the waveband............ 15
station lists................................ 17
station search............................ 15
usage........................................ 15
waveband menus...................... 17
Radio data system (RDS) ............ 20
RDS.............................................. 20
Recharging the phone battery...... 77
Regionalization............................. 20
Retrieving stations........................ 16
Route guidance...................... 58, 65
90
S
SAP mode.................................... 78
SD card......................................... 65
Selecting the waveband............... 15
Setting the navigation volume...... 35
Setting the volume.......................... 9
SIM Access Profile (SAP)............. 78
Speech recognition................. 72, 73
activating................................... 73
phone control............................ 73
usage........................................ 73
volume for voice output............. 73
Speed compensated volume.......... 9
Speller function............................. 44
Starting CD replay........................ 25
Station search............................... 15
Storing stations............................. 16
Switching the Infotainment
system on or off........................... 9
Switching the radio on.................. 15
Symbols overview ........................ 68
T
Theft-deterrent feature ................... 5
Tone settings................................ 12
Traffic announcements................. 14
U
Updating station lists.................... 17
Usage............... 9, 15, 25, 27, 31, 35
User defined POIs........................ 44
Using the AUX input..................... 27
Using the CD player..................... 25
Using the digital picture frame...... 31
Using the Infotainment system....... 9
Using the navigation system........ 35
Using the radio............................. 15
Using the USB port....................... 28
V
Voice recognition.......................... 72
Volume for voice output................ 73
Volume settings............................ 14
W
Waveband menus......................... 17
CD 400
Introduction .................................. 92
Radio ......................................... 104
Audio players ............................. 117
Phone ........................................ 132
Index .......................................... 148
92
Introduction
Introduction
General information ..................... 92
Theft-deterrent feature ................. 93
Control elements overview .......... 94
Operation ..................................... 96
Personalisation .......................... 100
General information
The Infotainment system provides
infotainment in your vehicle, using the
latest technology.
The radio can easily be used by
registering up to 36 FM, AM and DAB
(Digital Audio Broadcasting) radio
stations with the 1 ~ 6 preset buttons
per every six pages. DAB is only
available for Type A and Type D
models.
The integrated CD player can play
audio CD and MP3 (WMA) discs, and
the USB player can play connected
USB storage devices or iPod
products. The USB player is only
available for Type A and Type B
models.
The Bluetooth phone connection
function allows for the use of wireless
handsfree phone calls, as well as a
phone music player. The Bluetooth
phone connection function is only
available for Type A and Type B
models.
Connect a portable music player to
the exterior sound input and enjoy the
rich sound of the Infotainment
system. The AUX function is only
available for Type A and Type B
models.
The digital sound processor provides
a number of preset equaliser modes
for sound optimisation.
The system can be easily adjusted
with the carefully designed adjusting
device, smart displayer, and
multifunctional menu dial regulator.
■ The "Overview" section provides a
simple overview of the Infotainment
system's functions and a summary
of all regulatory devices.
■ The "Operation" section explains
the basic controls of the
Infotainment system.
Introduction
Screen display
(10) Station name
(11) Favourites page
(12) Stations list
(13) Band
93
(8) List indicator bar
(9) Menu
The screen display may differ from
the manual display since most screen
displays differ according to the
device's setup and vehicle
specification.
Theft-deterrent feature
Start-up screen
(1) Clock
(2) Disc loaded
(3) RDS service
(4) Inside air temperature (driver/
passenger)
(5) Bluetooth connected
(6) Bluetooth music
(7) Outside air temperature
(8) Date
Radio screen
(9) Category
The Infotainment system has an
electronic security system installed to
prevent theft.
The Infotainment system therefore
functions only in your vehicle and is
worthless to a thief.
CD/MP3 screen
(1) Playing time
(2) Folder/track
(3) Song title
(4) Artist
(5) Disc type
Settings screen
(6) Settings title
(7) Selection bar
94
Introduction
Control elements overview
Overview
3.
4.
Type A: Radio/DAB + CD/MP3 + AUX
+ USB/iPod + Bluetooth
Type B: Radio + CD/MP3 + AUX +
USB/iPod + Bluetooth
Type C: Radio + CD/MP3
Type D: Radio/DAB + CD/MP3
1. 1 ~ 6 preset buttons
◆ Hold down any of these buttons
to add the current radio station
to the current favourites page.
◆ Press any of these buttons to
select the channel linked to that
button.
2. m button with VOL control knob
5.
6.
7.
◆ Press this button to turn the
power on and off.
◆ Turn the control knob to adjust
the overall volume.
RADIO/BAND button
Select the FM, AM band radio or
DAB function.
CD button
Press this button to select the CD/
MP3 disc play function.
AUX button
Press this button to select the
AUX/USB/iPod/Bluetooth audio
function.
O button
◆ Press this button to activate the
Bluetooth mode.
◆ Hold down this button to turn the
mute/pause function for CD and
USB/iPod on and off.
Disc slot
This is the slot in which compact
discs are inserted or taken out.
8. TONE button
Press this button to adjust/select
the sound setup mode.
9. P BACK button
Cancel the input content or return
to the previous menu.
10. Multifunction knob
◆ Press the button to display the
currently functioning menu or
select the setup content and
setup values.
◆ Turn the control knob to move/
change the setup content and
setup values.
◆ In the Bluetooth handsfree
mode, take a call by pressing
the button. You can turn the
control knob to answer or reject
the call, and then press the
button to confirm.
11. CONFIG button
Press this button to enter the
system setup menu.
Introduction
12. INFO button
◆ Press this button to view the file
information when using the CD/
MP3 and USB/iPod play
modes.
◆ View information about a radio
station and the currently playing
song when using the radio
function.
13. R button
Press this button and take out the
disc.
14. TP button
While using the FM RDS function,
turn the TP (Traffic Programme)
function on or off.
15. AS 1-2 button
◆ Hold down this button to
automatically store the radio
stations to the AS station page
1 or 2.
◆ Press this button to select the
AS station pages 1 or 2.
16. FAV 1-2-3 button
Press this button to select the
page of saved favourite files.
17. 1 / 8 buttons
◆ Press these buttons when using
radio or DAB to automatically
seek stations with clear
reception. You can manually
set the broadcasting frequency
by holding down these buttons.
◆ Press these buttons while using
the CD/MP3 and USB/iPod play
modes to instantly play the
previous or next track.
◆ You can hold down these
buttons to quickly rewind/fast
forward through the currently
playing songs.
95
Steering wheel audio controls
Steering wheel audio control Type 1:
option
1. xn button
Press this button in any music
play mode to turn the mute
function on and off. In engaged
mode you can press this button to
reject calls or to finish the call.
96
Introduction
2. q button
◆ Press this button to answer the
call or enter the redial mode.
◆ Hold down this button to enter
the dialled call log or to move
back and forth from hands-free
mode and private call mode
during a call.
3. d SRC c button
◆ Press this button to select a
sound play mode.
◆ Turn the control to change the
registered radio station or
change the music being played.
4. + buttons
◆ Press the + button to increase
the volume.
◆ Press the - button to decrease
the volume.
Steering wheel audio control Type 2:
option
1. x button
Press this button to turn the mute
function on and off.
2. Not available.
3. d SRC c button
◆ Press this button to select a
sound play mode.
◆ Turn the control to change the
registered radio station or
change the music being played.
4. + button
◆ Press the + button to increase
the volume.
◆ Press the - button to decrease
the volume.
Operation
Buttons and control devices
The Infotainment system is operated
by using the function buttons,
multifunction knob, and the menu
indicated on the screen display.
The buttons and controls used in the
system are the following:
■ The Infotainment system buttons
and control knob
■ The steering wheel remote control
buttons
Introduction
System on and off
Turning off automatically
If you turn on the Infotainment system
using the m button while the ignition
switch (vehicle ignition key) is in the
off position, the Infotainment system
will automatically be turned off
10 minutes after the last user input.
Volume control
Press the m button to turn the system
on.
Once the power is turned on, the
previously used function will be
executed after time, date,
temperature, and function are ready.
Press the m button to turn the system
off.
■ Using the steering wheel remote
control, press the + and - buttons to
adjust the volume.
■ The current sound volume is
indicated.
■ Turning on the Infotainment system
power will set the volume level to its
previous selection (when it is less
than the maximum startup volume).
■ When turning on the power, the
maximum startup volume value can
be separately set (when the
previous volume level is less than
the maximum starting volume).
Auto volume control
Turn the VOL control knob to adjust
the volume.
97
Once the speed-compensating sound
volume setup starts operating, the
volume will automatically be
controlled according to the vehicle's
speed to offset the noise from the
engine and tyres. (Refer to Settings →
Radio settings → Auto volume
control).
98
Introduction
Volume limit at high
temperatures
If the inside temperature of the radio
is very high, the Infotainment system
will limit the controllable maximum
volume.
If necessary, the volume will
automatically decrease.
Press the TONE button when using
the relevant functioning mode.
Turn the multifunction knob to select
the desired tone control mode, and
then press the multifunction knob.
Tone settings
From Tone settings, sound features
can be setup differently according to
the FM, AM or DAB radio and each
audio player’s functions.
Turn the multifunction knob to select
the desired tone control value, and
then press the multifunction knob.
Tone settings menu
■ Bass: Adjust the bass level from -12
to +12.
■ Midrange: Adjust the midrange
level from -12 to +12.
■ Treble: Adjust the treble level from
-12 to +12.
■ EQ (Equaliser): Select or turn off
the sound style (OFF ↔ Pop ↔
Rock ↔ Classical ↔ Talk ↔
Country).
■ Fader: Adjust the front/rear speaker
balance from front 15 to rear 15 in
the six speaker system vehicle
model.
■ Balance: Adjust the left/right
speaker balance from left 15 to right
15.
Introduction
Select a function
99
CD/MP3 disk player
FM, AM or DAB radio
Press the RADIO/BAND button to
select FM, AM or DAB radio.
Press the multifunction knob to open
the FM menu, AM menu or DAB
menu that includes options for
selecting broadcast stations.
(1) Audio CD
(2) Audio CD with text
(3) MP3/WMA CD
Insert an audio CD or MP3 (WMA)
disc to be played with the printed
surface facing upwards in the disk
slot. When a disc is already inserted,
press the CD button to select the CD/
MP3 player.
From the steering wheel remote
control, press d SRC c to select the
CD/MP3 player.
(1) Audio CD
(2) MP3/WMA CD
Press the multifunction knob to open
the menu with options for the relevant
function or the menu of the relevant
device.
100
Introduction
USB/iPod audio play or AUX input
Connect the USB/iPod with music
files to be played to the USB
connecting terminal or connect the
audio output of the external audio
equipment to be listened to to the
AUX input terminal.
When the USB, iPod or AUX device is
already inserted, repeatedly press the
AUX button to select the desired
function (AUX → USB → Bluetooth
audio → AUX → ...)
From the steering wheel remote
control, press d SRC c to select the
desired mode.
Bluetooth handsfree phone device
Press the multifunction knob to open
the menu with options for the relevant
function or the menu of the relevant
device.
Press the O button to select the
Bluetooth handsfree phone function.
Press the multifunction knob to open
the Bluetooth menu with options for
the relevant function.
Personalisation
Main buttons and controls
The buttons and controls used in the
Settings are the following.
(11) CONFIG button
Press this button to enter the
Settings menu.
Introduction
(10) Multifunction knob
■ Turn the control knob to select the
desired menu or setup item.
■ Press the button to select/enter the
detailed control screen provided by
the current menu or setup item.
(9) P BACK button
Cancel the input item or return to the
previous screen or menu.
Example: Settings → Time Date → Set
date: 23 Jan 2012
How to use the Settings menu
for personalisation
■ Setup menus and functions may
differ according to the vehicle
model.
■ Reference: Table of information for
the Settings menu below.
101
Press the CONFIG button for the
Settings menu.
After referring to the table of
information for the Settings menu
below, turn the multifunction knob to
move to the desired settings menu,
and then press the multifunction
knob.
■ Indicates the detailed list for the
relevant settings menu or
functioning state.
■ If there is another detailed list from
the relevant detailed list, you can
repeat this action.
102
Introduction
Table of information for Settings
Languages
Turn the multifunction knob to attain
the desired setup value or functioning
state, and then press the
multifunction knob.
■ If the relevant detailed list is made
of several items, then repeat this
action.
■ Set/enter the relevant setup value
or the functioning state will change.
Select the desired language for the
display.
Time Date
■ Set time: Manually set the hours
and minutes for the current time.
■ Set date: Manually set the current
year/month/date.
■ Set time format: Select 12h or 24h
time display.
■ Set date format: Set the date
display format.
YYYY.MM.DD: 2012 Jan. 23
DD/MM/YYYY: 23 Jan. 2012
MM/DD/YYYY: Jan. 23, 2012
■ RDS clock synchronization: Select
On or Off.
Introduction
Radio settings
- TA volume: Set the TA volume.
■ DAB settings: Set the DAB settings.
- Auto ensemble linking: Select On
or Off.
- Auto linking DAB-FM: Select On
or Off.
- Dynamic audio adaption: Select
On or Off.
- Band selection: Set Both, L-Band
or Band III.
Bluetooth settings
■ Auto volume control: Set Off/Low/
Medium/High.
■ Maximum startup volume:
Manually set the maximum limit for
the startup volume.
■ Radio favourites: Manually set the
Max. number of favourites pages.
■ RDS options: Set the RDS options.
- RDS: Select On or Off.
- Regional: Select On or Off.
- Text scroll freeze: Select On or
Off.
- Radio text: Select On or Off.
103
■ Activation: Select On or Off.
■ Device list: Select the desired
device and Select, Disconnect or
Delete.
■ Pair device: Try pairing a new
Bluetooth device.
■ Change Bluetooth code: Manually
change/set the Bluetooth code.
■ Restore factory settings: Restore
the initial setup values back to the
default settings.
104
Radio
Radio
Usage ........................................ 104
Radio data system (RDS) .......... 112
Fixed mast antenna ................... 116
Usage
Before using FM, AM or DAB
radio
Main buttons and controls
(3) RADIO/BAND button
Toggle between FM, AM or DAB band
radio.
(10) Multifunction knob
■ Turn this control knob to manually
find a broadcasting frequency.
■ Press this button to access the
menu screen from the current
mode.
(9) P BACK button
Cancel the input item or return to the
previous screen/menu.
(17) 1 / 8 buttons
■ Press these buttons to
automatically search for available
radio stations.
■ Press and hold these buttons to
change the radio frequency as
desired, and then let the button stop
at the current frequency.
(16) FAV 1-2-3 button
Press this button to move through the
pages of saved favourite radio
stations.
(1) 1 ~ 6 preset buttons
■ Press and hold any of these preset
buttons to register the current radio
station to that button.
■ Press this button to select the
station registered to the preset
button.
(15) AS 1-2 button
■ Press and hold this button to
automatically store the radio
stations to the AS station pages 1
or 2.
■ Press this button to select the AS
station pages 1 or 2.
(14) TP button
While using the FM RDS function,
turn the TP (Traffic Programme)
function On or Off.
(12) INFO button
View the information for the
broadcasted radio stations.
(6) O button
Radio
Press this button to turn the mute
function on and off.
105
Automatically searching for a radio
station
Automatically searching for the DAB
service component
Press the 1 / 8 buttons to
automatically search for available
radio stations with good reception.
Press the 1 / 8 buttons to
automatically seek for the available
DAB service component in the
current ensemble.
Listening to a radio or DAB
station
Selecting the FM, AM or DAB mode
Repeatedly press the RADIO/BAND
button to select FM, AM or DAB band.
The previously chosen broadcasting
station will be received.
106
Radio
Seeking for a radio station
Seeking for a DAB ensemble
Linking the DAB service
Press and hold the 1 / 8 buttons
to quickly change the frequency, and
then release the button at the desired
frequency.
Press and hold the 1 / 8 buttons
to automatically seek for the available
DAB service component with good
reception.
(DAB-DAB on/DAB-FM off)
(DAB-DAB off/DAB-FM on)
Radio
(DAB-DAB on/DAB-FM on)
When you setup the Auto linking
DAB-FM as activated, if the DAB
service signal is weak, the
Infotainment system receives the
linked service component
automatically (refer to Settings →
Radio settings → DAB settings → Auto
linking DAB-FM).
107
Tuning a radio station manually
Tuning a DAB station manually
Turn the multifunction knob to
manually find the desired
broadcasting frequency.
From the DAB mode, press the
multifunction knob to enter the DAB
menu.
Turn the multifunction knob to select
DAB manual tuning and then press
the multifunction knob.
Turn the multifunction knob to
manually find the desired
broadcasting frequency, and then
press the multifunction knob.
108
Radio
Using the DAB stations list
Showing the DAB information
Using the preset buttons
Registering the preset button
Turn the multifunction knob to display
the DAB stations list.
■ The DAB stations list information
will be displayed.
■ If the DAB stations list is empty, the
DAB stations list update is started
automatically.
Turn the multifunction knob to select
the desired list, and then press the
multifunction knob to receive the
relevant broadcasting channel.
Repeatedly press the INFO button to
select the desired display mode for
the DAB station information.
The number 1 broadcasting
information of the selected favourites
preset page (FAV1, FAV2, etc.) will
be displayed.
Press the FAV 1-2-3 button to select
the desired page of saved favourites.
■ Up to 3 favourites pages can be
saved, and each page can store up
to six radio or DAB stations.
Radio
■ It is possible to setup the number of
favourites pages being used under
Settings → Radio settings → Radio
favourites → Max. number of
favourites pages.
■ If a new radio station is registered
to one of the previously registered
1 ~ 6 preset buttons, its previous
content will be deleted and
replaced with the new radio or DAB
station that is saved.
The number 1 broadcasting
information of the selected favourites
presets page will be displayed.
Press one of the 1 ~ 6 preset buttons
to directly listen to the radio or DAB
station saved to that button.
Using the auto store stations
109
■ An update message appears on the
display.
■ Up to two pages can be saved and
each page can store up to six radio
stations.
Listening to the auto stored stations
Registering the stations automatically
Listening to the preset button directly
Repeatedly press the FAV 1-2-3
button to select the desired favourites
presets page.
Hold down the AS 1-2 button to store
the stations with good reception to
that button of the auto store page.
Repeatedly press the AS 1-2 button
to select the desired auto store preset
page.
The number 1 broadcasting
information of the selected favourites
page will be displayed.
110
Radio
Press one of the 1 ~ 6 preset buttons
to directly listen to the radio station
saved to that button.
FM, AM or DAB menu → Favourites
list
DAB menu → DAB manual tuning
Using the FM, AM or DAB menu
Press the multifunction knob to
display the radio menu or DAB menu.
Turn the multifunction knob to move
to the desired menu item, and then
press the multifunction knob to select
the relevant item or to display the
item's detailed menu.
From FM menu, AM menu or DAB
menu, turn the multifunction knob to
select the Favourites list, and then
press the multifunction knob.
The Favourites list information will be
displayed.
Turn the multifunction knob to select
the desired Favourites list, and then
press the multifunction knob to
receive the relevant broadcasting
channel.
From the DAB menu, turn the
multifunction knob to select DAB
manual tuning, and then press the
multifunction knob. Turn the
multifunction knob to manually find
the desired broadcasting frequency.
Radio
FM or AM menu → FM or AM stations
list
FM or DAB menu → FM or DAB
category list
From the FM menu or AM menu, turn
the multifunction knob to select the
FM stations list or the AM stations
list, and then press the multifunction
knob.
The FM stations list or AM stations
list information will be displayed.
Turn the multifunction knob to select
the desired list, and then press the
multifunction knob to receive the
relevant broadcasting channel.
From the FM menu or DAB menu,
turn the multifunction knob to move to
the FM category list or the DAB
category list, and then press the
multifunction knob.
The FM category list or the DAB
category list will be displayed.
Turn the multifunction knob to select
the desired list, and then press the
multifunction knob to receive the
relevant broadcasting frequency.
111
DAB menu → DAB announcements
From the DAB menu, turn the
multifunction knob and move to the
DAB announcements, and then press
the multifunction knob.
The DAB announcements will be
displayed.
Turn the multifunction knob to select
the desired list, and then press the
multifunction knob to receive the
relevant broadcasting frequency.
112
Radio
FM, AM or DAB menu → Update the
FM, AM or the DAB stations list
multifunction knob or the P BACK
button to stop it from saving
changes.
Radio data system (RDS)
■ The Radio Data System (RDS) is a
service by FM stations that
considerably makes it easier to find
radio stations with fault-free
reception.
From the FM menu, AM menu or DAB
menu, turn the multifunction knob and
move to Update FM stations list,
Update AM stations list or Update
DAB stations list, and then press the
multifunction knob.
■ The FM stations list update, AM
stations list update or DAB stations
list update will proceed.
■ During the FM stations list update,
AM stations list update or DAB
stations list update, press the
■ RDS stations are indicated by the
programme name with the
broadcasting frequency.
View RDS broadcasting
information
While receiving RDS broadcasting,
press the INFO button to check RDS
broadcasting information that is being
received.
Configuring RDS
Press the CONFIG button to display
the Settings menu.
Turn the multifunction knob to move
to Radio settings, and then press the
multifunction knob.
Radio
Turn the multifunction knob to select
RDS options, and then press the
multifunction knob.
Switching RDS on and off
Set the RDS option On or Off.
The following advantages result from
activating RDS:
■ On the display, the programme
name of the set station appears
instead of its frequency.
■ The Infotainment system always
tunes into the best receivable
broadcasting frequency of the set
station by means of AF (alternative
frequency).
113
From RDS options, turn the
multifunction knob to move to RDS
Off, and then press the multifunction
knob to turn on the RDS function.
Switching regionalisation on
and off
RDS must be activated for
regionalisation.
At certain times, some RDS stations
broadcast regionally different
programmes on different frequencies.
Set the option Regional to On or Off.
Only alternative frequencies (AF) with
the same regional programmes are
selected.
If regionalisation is switched off,
alternative frequencies of the stations
are selected without regarding
regional programmes.
From Settings → Radio settings →
RDS options, turn the multifunction
knob to move to Regional Off, and
then press the multifunction knob to
turn on the Regional function.
Switching Text scroll freeze on
and off
Switch the Text scroll freeze function
(for displaying the information of the
programme service) on or off:
114
Radio
From Settings → Radio settings →
RDS options, turn the multifunction
knob to move to Text scroll freeze
Off, and then press the multifunction
knob to turn on the Text scroll freeze
function.
Switching the Radio text
function on and off
Switch the Radio text function for
displaying the information of the
programme service on and off.
From Settings → Radio settings →
RDS options, turn the multifunction
knob to select Radio text Off, and then
press the multifunction knob to turn
on the Radio text function.
Volume of the traffic
announcements (TA)
The minimum volume of the traffic
announcements (TA) can be preset.
The minimum volume of the traffic
announcements can be increased or
reduced in comparison to the normal
audio volume.
From RDS options, turn the
multifunction knob to move to TA
volume, and then press the
multifunction knob.
Turn the multifunction knob to adjust
the TA volume level, and then press
the multifunction knob.
Radio traffic service
TP = traffic programme
Radio traffic service stations are RDS
stations that broadcast traffic news.
Switch the traffic announcement
standby facility of the Infotainment
system on or off:
Radio
115
Blocking out traffic
announcements
Block out a traffic announcement, e.g.
during CD or MP3 replay or during
radio reception:
Press the TP button to turn the traffic
programme service function on or off.
■ If the radio traffic service is
switched on, [ ] is displayed in the
radio main menu.
■ If the current station is not a radio
traffic service station, then a search
is automatically started for the next
radio traffic service station.
■ Once a radio traffic service station
has been found, [TP] is displayed in
the radio main menu.
■ If the radio traffic service is
switched on, then the CD, MP3,
USB, iPod, Bluetooth music or AUX
replay is interrupted for the duration
of the traffic announcement.
Press the TP button.
Switch on the radio traffic service and
fully turn down the volume of the
Infotainment system.
The traffic announcement is aborted,
but the radio traffic service remains
switched on.
116
Radio
Blocking out current traffic
announcements
Fixed mast antenna
Block out a current traffic
announcement, e.g. during TA radio
reception:
Install the antenna fully tightened and
adjusted to the upright position to
ensure proper reception.
To remove the roof antenna, rotate it
counterclockwise. To install the roof
antenna, rotate it clockwise.
(1) Blocking out the status indicator:
[TP] → TP
Press the TP button.
the roof panel. Be sure to remove
your antenna before entering the
automatic car wash.
Caution
Be sure to remove the antenna
before entering a place with a low
ceiling or it may be damaged.
Entering the automatic car wash
with the antenna installed may
result in damage to the antenna or
Audio players
Audio players
CD player
CD player ................................... 117
Auxiliary devices ........................ 125
Before using the CD player
The CD/MP3 player of this system
can play audio CD and MP3 (WMA)
discs.
Important information about audio CD
and MP3 (WMA) discs
Caution
In any case, do not insert any
DVDs, mini disks with a diameter
of 8 cm, or discs with abnormal
surfaces in this CD/MP3 (WMA)
player.
Do not put any stickers on the disk
surface. Such disks may get stuck
in the CD player, and damage the
drive device. If this occurs, then
the device will need to be replaced
at high costs.
■ An audio CD disc with an antipiracy function with no compatibility
with the audio CD standard may not
work properly or not at all.
117
■ CD-R and CD-RW discs that are
manually recorded are more often
handled with carelessness than the
original CD discs. Manually
recorded CD-R and CD-RW discs
should be handled with special
care. Please refer to the following.
■ Manually recorded CD-R and CDRW discs may not play properly or
not at all. In such cases, this is not
a problem with the device.
■ When changing discs, take care to
not smear any fingerprints on the
playing side.
■ After removing the disc from the
CD/MP3 player, make sure to
immediately put the disc into a disc
sleeve to prevent it from being
damaged or smeared with dust.
■ If the disc is smeared with dust or
liquid, then this may cause
problems by contaminating the lens
of the CD/MP3 player inside the
device.
■ Protect the disc from heat and
exposure to direct light.
118
Audio players
Usable disc type
■ This product can play audio CD/
MP3 (WMA) discs.
◆ CD-DA: CD-R/CD-RW
◆ MP3 (WMA): CD-R/CD-RW/CDROM
■ The MP3 (WMA) files below cannot
be played.
◆ Files encoded in MP3i (MP3
interactive) or MP3 PRO
standards
◆ MP3 (WMA) files encoded in nonstandards
◆ MP3 files that are not in MPEG1
Layer3 format
Cautions for using discs
■ Do not use any of the discs
described below. Excessive use of
these discs in the player may cause
problems.
◆ Discs with stickers, labels, or a
protective cell attached
◆ Discs affixed with a label printed
with an inkjet printer
■
■
■
■
■
◆ Discs that are made by overburning, thus holding data
exceeding the standard capacity
◆ Discs with cracks or scratches or
which are bent
◆ An 8 cm disc or a non-circular
disc (quadrangle, pentagon,
oval)
Do not put anything other than
discs in the disc slot since this may
cause trouble or damage.
The disc player may not work
properly if the heater is turned on in
cold weather due to moisture
created inside the device. If this is
a concern, keep the product off for
about one hour before use.
Play may be stopped due to the
vehicle shaking while driving on
rugged roads.
Do not forcefully take out or insert
the disc or block it with your hand
while it is being ejected.
Insert the disc with the printed side
facing up. It cannot be played if it is
inserted upside down.
■ Do not touch the recording side with
your hand while handling the disc
(the side without any print or
decoration).
■ Place discs that are not being used
in cases, and keep them in a place
not exposed to direct light or high
temperature.
■ Do not smear any chemical
substances on the disc. Clean
discs of dirt with a moist, soft cloth,
wiping from the centre to the edge.
Caution for using CD-R/RW discs
■ When using CD-R/CD-RW discs,
only the discs that have been
"finalised" can be used.
■ Discs that are created with a PC
may not play according to the
application programme setup and
environment.
■ CD-R/CD-RW discs, especially
bulk discs, may not work if they are
exposed to direct light or high
temperature, or if they are kept
inside your vehicle for a long time.
Audio players
■ The title and other text information
recorded on CD-R/CD-RW discs
may not be displayed on this
device.
■ CD-RW discs may have longer
loading times than CDs or CD-R
discs.
■ Damaged music files may not be
played or will be cut off while
playing.
■ Folders and music files are
displayed in the order of: symbol →
number → alphabet.
■ Some anti-piracy discs may not be
played.
■ An MP3 (WMA) disc can have a
maximum of 512 files for each of
the 10 folder levels, and a
maximum number of 999 files can
be played.
■ The folder and file names are not
arranged, and are indicated in the
order in which they are recorded on
the disc.
■ This system can only recognise
MP3 (WMA) discs made in
ISO-9660 level 1/2 or in the Joliet
file system. (It does not support the
UDF file system.)
■ MP3 (WMA) files are not
compatible with packet writing data
transmission.
■ The disc on which MP3 (WMA) files
and audio data (CDDA) are written
may not be played if it is a CD-Extra
or Mixed-Mode CD.
■ The file/folder names that can be
used per disc storage type are the
following, including the four-digit file
name extensions (.mp3):
◆ ISO 9660 Level 1: Maximum of
12 characters
◆ ISO 9660 Level 2: Maximum of
31 characters
◆ Joliet: Maximum of 64 characters
(1 byte)
◆ Windows long file name:
Maximum of 28 characters
(1 byte)
119
Cautions for using MP3 (WMA) music
files
■ This product can play MP3 (WMA)
files with .mp3, .wma (lower case
letters) or .MP3 and .WMA (capital
letters) file name extensions.
■ MP3 files that can be played by this
product are the following:
◆ Bit rate: 8kbps ~ 320kbps
◆ Sampling frequency: 48kHz,
44.1kHz, 32kHz (for MPEG-1),
24kHz, 22.05kHz, 16kHz (for
MPEG-2)
■ While this product can play files
with an 8kbps ~ 320kbps bit rate,
files with a bit rate above 128kbps
will result in high quality sound.
■ This product can display ID3 tag
(version 1.0, 1.1, 2.2, 2.3 or 2.4)
information for MP3 files, such as
the album name and the artist.
120
Audio players
■ To display album (disc title), track
(track title), and artist (track artist)
information, the file should be
compatible with the ID3 tag V1 and
V2 formats.
■ This product can play MP3 files
using VBR. When playing an MP3
file of this VBR type, the remaining
time displayed may be different
from the real time.
Playing CD/MP3
Main buttons and controls
(4) CD button
Select the CD/MP3 player.
(10) Multifunction knob
■ Turn the control knob to move to the
track list, menu, or MP3 (WMA)
track information item.
■ Press the button to display the
menu screen for the current item or
current mode.
(17) 1 / 8 buttons
■ Press these buttons to play the
previous or next track.
■ Hold down these buttons to rewind
or fast forward through the track,
and release the button to resume
playing at normal speed.
(13) R button
Eject the disc.
(12) INFO button
Display the information for the track
being played.
(6) O button
Hold down the button to turn the mute
function on or off.
Inserting and playing the disk
Insert the disc to be played with the
printed surface facing upwards in the
disc inserting slot.
■ Once the reading of the disc
information is completed, the
Infotainment system will
automatically start playing from
track 1.
■ When a non-readable disc is
inserted, the disc will automatically
be ejected with the display of a disc
error message, and then the
system will switch to the previously
used function or FM radio.
Audio players
(1) Audio CD
(2) Audio CD with text
(3) MP3/WMA CD
When a disc to be played is already
inserted, repeatedly press the CD
button to select CD/MP3 play.
■ If there is no disc to be played, No
CD inserted will be displayed on the
screen and the function will not be
selectable.
■ The track that was previously
played will automatically play.
121
Ejecting the disc
Changing the playing track
To eject the disc, press the R button
and take out the disc.
■ When the disc comes out, it
automatically switches to the
previously used function or FM
radio.
■ The disc will automatically be
inserted back again if it is not taken
out for some time.
Press the 1 / 8 buttons in play
mode to play the previous or next
track.
Using the steering wheel remote
control, tracks can easily be changed
by turning the d SRC c control knob.
122
Audio players
For MP3 (WMA) tracks, turn the
multifunction knob to move to the play
track list, and then press the
multifunction knob to instantly change
it.
Changing playing position
View information on playing track
Hold down the 1 / 8 buttons
during play mode to rewind or fast
forward through the song. Release
the button to resume playing the song
at normal speed.
The volume is slightly reduced during
rewinding and fast forwarding, and
the playing time will be displayed.
Press the INFO button in play mode
to display information about the track
being played.
If there is no information on the
playing track for audio CDs, then the
system will display No information.
For MP3 (WMA) tracks, more
information can be viewed by turning
the multifunction knob from the track
information display.
■ The information displayed includes
the file name, folder name, and ID3
tag information saved with the
song.
Audio players
If incorrect ID3 tag information (e.g.
artist, song title) was added to the
MP3 (WMA) files before they were
burnt to disc, this information will be
displayed as is by the Infotainment
system.
Incorrect ID3 tag information
cannot be modified or corrected on
the Infotainment system (ID3 tags
can only be corrected on a PC).
■ The information for songs
expressed in special symbols or in
unavailable languages may be
displayed as ---- or are not
displayed at all.
Using the CD menu
123
CD menu → Track list
Changing the playback mode
From the play mode, press the
multifunction knob to display the CD
menu.
Turn the multifunction knob to select
the shuffle or repeat playback
functions, and then press the
multifunction knob to turn the relevant
functions On or Off.
For audio CD discs, turn the
multifunction knob from the CD
menu to select the Track list, and then
press the multifunction knob.
Turn the multifunction knob to find the
desired track list, and then press the
multifunction knob to play the
selected track.
124
Audio players
CD menu → Folders
For MP3 (WMA) discs, turn the
multifunction knob from the CD
menu to select Folders, and then
press the multifunction knob.
Turn the multifunction knob to select
the desired folder, and then press the
multifunction knob.
Turn the multifunction knob to find the
desired track, and then press the
multifunction knob to play the
selected track from the selected
folder.
CD menu → Search...
For MP3 (WMA) discs, turn the
multifunction knob from the CD
menu, move to Search..., and then
press the multifunction knob.
■ After the system reads the disc
information, the first song of the
Playlist will be displayed.
■ If there are no music files in the
Playlist, the first song from the
Artists will be displayed.
Press the multifunction knob again,
and from the displayed search item,
turn the multifunction knob to select
the desired play mode.
The number of relevant songs will be
displayed by Playlist, Artists, Albums,
Songs and Genres.
Audio players
■
Turn the multifunction knob to select
the detailed classification item, and
then press the multifunction knob.
Turn the multifunction knob to find the
desired track/title, and then press the
multifunction knob to play the
selected track.
Auxiliary devices
USB player
Cautions for using USB devices
■ Operation cannot be guaranteed if
the HDD built-in USB mass storage
device or CF or SD memory card is
■
■
■
■
connected by using an USB
adapter. Use a USB of flash
memory type storage device.
Take caution to avoid static
electricity discharge when
connecting or disconnecting the
USB device. If connection and
disconnection are repeated many
times in a short time, this may
cause a problem in using the
device.
Operation is not guaranteed if the
connecting terminal of the USB
device is not metal.
The connection with i-Stick Type
USB storage devices may be faulty
due to vehicle vibration, so their
operation cannot be guaranteed.
Be careful not to touch the USB
connecting terminal with an object
or any part of your body.
The USB storage device can only
be recognised when it is formatted
in FAT16/32 file format. Only
devices with an allocated unit size
of 512 byte/sector or 2,048 byte/
■
■
■
■
125
sector can be used. NTFS and
other file systems cannot be
recognised.
According to the type and capacity
of the USB storage device and the
type of the stored file, the time it
takes to recognise the files may
differ. This is not a problem with the
product in this case, so please wait
for the files to be processed.
Files in some USB storage devices
may not be recognised due to
compatibility problems, and
connections with a memory reader
or a USB hub are not supported.
Please check the device's
operation in the vehicle before use.
When devices such as an MP3
player, mobile phone, or digital
camera are connected through a
mobile disc, it may not operate
normally.
Do not disconnect the USB storage
device while it is being played. This
may cause damage to the product
or the performance of the USB
device.
126
Audio players
■ Disconnect the connected USB
storage device when the vehicle
ignition is turned off. If the ignition
is turned on while the USB storage
device is connected, the USB
storage device may be damaged or
may not operate normally in some
cases.
■ USB storage devices can only be
connected to this product for the
purpose of playing music files.
The product's USB terminal should
not be used to charge USB
accessory equipment since the
heat generation using the USB
terminal may cause performance
issues or damage to the product.
■ When the logical drive is separated
from a USB mass storage device,
only the files from the top-level
logical drive can be played for USB
music files. This is why the music
files to be played should be stored
in the top-level drive of the device.
Music files, in particular USB
storage devices, may also not be
normally played if an application is
loaded by partitioning a separate
drive inside the USB device.
■ Music files to which DRM (Digital
Right Management) is applied
cannot be played.
■ This product can support USB
storage devices that are up to
16 Gigabytes in capacity with a limit
of 999 files, 512 folders, and
10 stages of folder structure.
Normal usage cannot be
guaranteed for storage devices that
exceed this limit.
Cautions for using USB music files
■ Damaged music files may be cut off
during playback or may not be
played at all.
■ Folders and music files are
displayed in the order of Symbol →
Number → Language.
■ A maximum of 64 characters can
be recognised for folder or file
names written in the Joliet file
system.
About MP3 (WMA) music files
■ The MP3 files that can be played
are the following:
◆ Bit rate: 8kbps ~ 320kbps
◆ Sampling frequency:
48kHz, 44.1kHz, 32kHz (for
MPEG-1)
24kHz, 22.05kHz, 16kHz (for
MPEG-2)
■ This product displays MP3 (WMA)
files with the mp3, .wma (lower
case letters) or .MP3 or .WMA
(capital letters) file name
extensions.
■ This product can display ID3 tag
(version 1.0, 1.1, 2.2, 2.3, 2.4)
information about album, artist, etc.
for MP3 files.
■ The file/folder names that can be
used according to the storage type
are the following, including the four
character file name extension
(.mp3):
Audio players
◆ ISO 9660 Level 1: Maximum of
12 characters
◆ ISO 9660 Level 2: Maximum of
31 characters
◆ Joliet: Maximum of 64 characters
(1 byte)
◆ Windows long file name:
maximum of 28 characters
(1 byte)
■ This product can play MP3 files
which use VBR. When a VBR type
MP3 file is being played, the
remaining time displayed may be
different from the actual time
remaining.
Main buttons and controls
The following main buttons and
controls are used to play USB music
files.
(5) AUX button
Press the button repeatedly when the
USB device is connected to select the
USB play mode.
(10) Multifunction knob
■ Turn the control knob to move to the
track list, menu or MP3 (WMA)
track information.
■ Press the button to display the
menu screen provided by the
current item or current mode.
(17) 1 / 8 buttons
■ Press these buttons to play the
previous or next track.
■ Hold down these buttons to rewind
or fast forward, and then release to
play at normal speed.
(12) INFO button
Displays the information of the track
being played.
(6) O button
Hold down the button to turn the
pause function on or off.
(9) P BACK button
Cancel the input item or return to the
previous menu.
127
Connecting the USB storage device
Connect the USB storage device in
which music files are stored to the
USB connection terminal.
128
Audio players
Afterwards, the functions of the USB
player are operated similarly to CD/
MP3 playback.
Ending the USB music files playback
Press the RADIO/BAND or CD button
to select other functions.
To end the play and disconnect the
USB storage device, use Menu USB
→ Remove USB to safely remove the
USB storage device.
■ Once the product finishes reading
the information on the USB storage
device, it will automatically play
from track 1.
■ If a non-readable USB storage
device is connected, then an error
message will appear and the
product will automatically switch to
the previously used function or the
FM radio function.
If the USB storage device to be
played is already connected,
repeatedly press the AUX button to
select the USB player.
It will automatically play from the point
at which the playback stopped.
Using the USB menu
The instructions for Shuffle songs/
Repeat/Folders/Search... from the
Menu USB are similar to the CD/MP3
player's CD menu; only the Remove
USB item has been added. Refer to
the CD/MP3 player functions from the
CD menu.
Menu USB→ Remove USB
Press the multifunction knob from
play mode to display the Menu USB.
Turn the multifunction knob to select
Remove USB, and then press the
multifunction knob to display the
message notifying that it is safe to
remove the USB device.
Disconnect the USB device from the
USB connection terminal.
Return to the previously used
function.
Audio players
iPod player
Main buttons and controls
The following main buttons and
controls are used to play iPod music
files.
(5) AUX button
Press the button repeatedly when the
iPod is connected to select the iPod
play mode.
(10) Multifunction knob
■ Turn the control knob to move and
display the track list that is playing.
■ Press the button to display the
menu screen provided by the
current item or current mode.
(17) 1 / 8 buttons
■ Press these buttons to play the
previous or next track.
■ Hold down these buttons to rewind
or fast forward, and then release to
play at normal speed.
(12) INFO button
Displays the information of the track
being played.
(6) O button
Hold down the button to turn the
pause function on or off.
(9) P BACK button
Cancel the previous item or return to
the previous menu.
129
◆ iPod 120GB & 160GB Classic
◆ iPod 1G, 2G, & 3G Touch
◆ iPhone 3G & 3GS
Connecting the iPod player
Connect the iPod device in which the
music files are stored to the USB
connection terminal.
■ The iPod product models that are
connected/supported by this
product are the following:
◆ iPod 2G Nano/iPod 3G Nano/
iPod 4G & 5G Nano
■ Only connect the iPod to this
product with connection cables
supported by the iPod products.
Other connection cables cannot be
used.
■ In some cases, the iPod product
may be damaged if the ignition is
turned off when it is connected to
the product.
When the iPod product is not being
used, keep it separately from this
130
Audio players
product with the vehicle ignition
turned off.
■ Once the product finishes reading
the information on the iPod device,
it will automatically play from track
1 or the previously played track.
■ If a non-readable iPod device is
connected, then the relevant error
message will appear and the
product will automatically switch to
the previously used function or the
FM radio function.
■ It will automatically play from the
previously played point.
■ The playback functions and the
information display items of the
iPod player used with this product
may be different from the iPod in
terms of play order, method, and
the information displayed.
Afterwards, the functions to play the
iPod are operated similarly to CD/
MP3 playback.
Log-off the iPod playback
To end the playback, press the
RADIO/BAND or the CD button to
select other functions.
Using the iPod Menu
From the iPod Menu, the instructions
for Shuffle songs/Repeat/Search...
(including Audiobooks and
Composers) are similar to the CD/
MP3 player's CD menu; only the Eject
iPod item has been added. Refer to
each item of CD/MP3 for use.
If the iPod device to be played is
already connected, repeatedly press
the AUX button to select the iPod
player.
iPod Menu → Eject iPod
From the iPod mode, press the
multifunction knob to display the iPod
Menu.
Turn the multifunction knob to move
to Eject iPod, and then press the
multifunction knob to display the
message notifying you that it is safe
to remove the device.
Separate the iPod device from the
USB connection terminal.
Return to the previously used
function.
Audio players
Exterior sound (AUX) Input
Main buttons and controls
The following main buttons and
controls are used to enjoy the rich
sound of the Infotainment system
from the sound output of a connected
exterior sound device.
(5) AUX button
When an exterior sound device is
connected, press the button
repeatedly to select the exterior
sound input mode.
(2) m button with VOL control knob
Turn the control knob to adjust the
volume.
(6) O button
Hold down this button to turn the mute
function On or Off.
131
Connecting an exterior sound
Connect the audio output of the
external audio equipment to the AUX
input terminal.
The Infotainment system will
automatically switch to the exterior
sound (AUX) input mode when the
exterior sound device is connected.
Press the AUX button to switch to the
exterior sound input mode if the
exterior sound system has already
been connected.
Turn the VOL control knob to adjust
the volume.
132
Phone
Phone
Bluetooth®
Main buttons and controls
Bluetooth® ................................. 132
Hands free phone ...................... 137
The following main buttons and
controls are used to play music files
or use the call functions via a
Bluetooth device.
(6) O button
Press this button to activate the
Bluetooth mode.
(5) AUX button
When a Bluetooth device with a music
player function is connected, press
this button repeatedly to select
Bluetooth audio play mode.
(10) Multifunction knob
■ Press the button in Bluetooth
phone mode to display the menu
screen.
■ Turn the control knob to move to the
menu or setup value.
(17) 1 / 8 buttons
■ Press these buttons in Bluetooth
audio play mode to play the
previous or next track.
■ Hold down these buttons to rewind
or fast forward, and release to play
at normal speed.
Connecting Bluetooth
Registering the Bluetooth device
Register the Bluetooth device to be
connected to the Infotainment system
with the vehicle ignition turned off.
Firstly, set up the Bluetooth device to
be connected from Bluetooth
settings to enable other devices to
search for the Bluetooth device.
Phone
Press the CONFIG button, and use
the multifunction knob to move to
Settings → Bluetooth settings →
Bluetooth → Add device (Handsfree),
and then press the multifunction
knob.
■ Bluetooth devices can be
registered not only by using the
CONFIG button, but also by using
Phone Menu → Bluetooth settings
→ Bluetooth → Add device
(Handsfree).
■ If there already is a Bluetooth
device connected to the
Infotainment system, the Bluetooth
is busy message will appear.
■ Connection standby will be
displayed with a message and a
security code. (The initial value is
0000, and can be changed from
Settings → Bluetooth settings →
Bluetooth → Change Bluetooth
code.)
The Infotainment system can be
found by searching the to-beconnected Bluetooth device.
Enter the security code for the
Infotainment system through the
Bluetooth device.
If the registration of the device to be
connected to the Infotainment system
is successful, then the screen will
display the information of the
Bluetooth device.
133
The Infotainment system can register
up to five Bluetooth devices.
Connecting/deleting/separating the
Bluetooth devices
Firstly, set up the Bluetooth device to
be connected from Bluetooth
settings to enable other devices to
search for the Bluetooth device.
134
Phone
Use the multifunction knob to move
from the registered Bluetooth device
to the device to be deleted, and then
press the multifunction knob.
Press the CONFIG button, and use
the multifunction knob to move to
Settings → Bluetooth settings →
Bluetooth → Device list and then
press the multifunction knob.
Use the multifunction knob to move
from the registered Bluetooth device
to the device to be connected, and
then press the multifunction knob.
To disconnect the currently
connected Bluetooth device from the
device list screen, select the
connected device, which will display
Disconnect, and then press the
multifunction knob.
Cautions for registering/connecting
Bluetooth
■ When it is not possible to connect
to Bluetooth, delete the entire
device list from the Bluetooth
Phone
device to be connected, and try
again. If deleting the entire device
list does not work, then reinstall the
battery and reconnect.
■ If there is a problem after the
Bluetooth device has been
connected, use the multifunction
knob to carry out Settings →
Bluetooth settings → Restore
factory settings.
Initialise the device with the
problem caused by an error that
occurred with the connection of the
Bluetooth device and the
Infotainment system.
■ Sometimes, Bluetooth can only be
connected through handsfree or
the Bluetooth audio play functions
despite a stereo headset being
connected. In this case, try and
reconnect the Infotainment system
using the Bluetooth device.
■ For Bluetooth devices that do not
support stereo headsets, the
Bluetooth audio play function
cannot be used.
Bluetooth audio
How to play Bluetooth audio
■ A mobile phone or Bluetooth device
that supports A2DP (Advanced
Audio Distribution Profile) versions
over 1.2 must be registered and
connected to the product.
■ From the mobile phone or
Bluetooth device, find the Bluetooth
device type to set/connect the item
as a stereo headset.
A musical note icon n will appear at
the bottom right of the screen, if the
stereo headset is successfully
connected.
■ Do not connect the mobile phone to
the Bluetooth connection terminal.
An error may occur if it is connected
during the CD/MP3 and Bluetooth
audio play mode.
135
Playing Bluetooth audio
Press the AUX button repeatedly to
select the connected Bluetooth audio
play mode.
If the Bluetooth device is not
connected, then this function cannot
be selected.
Activating the mobile phone or
Bluetooth device will play the music
files.
136
Phone
■ The sound played by the Bluetooth
device is delivered through the
Infotainment system.
■ For Bluetooth audio to play, the
music must at least be played once
from the music player mode of the
mobile phone or Bluetooth device
after connecting as a stereo
headset. After being played at least
once, the music player will
automatically play upon entering
play mode, and it will automatically
stop when the music player mode
ends. If the mobile phone or
Bluetooth device is not in the
waiting screen mode, some
devices may not automatically play
in Bluetooth audio play mode.
Press the 1 / 8 buttons to switch
to the previous or next track, or hold
down these buttons to fast forward or
rewind.
■ This function only operates with
Bluetooth devices that support
AVRCP (Audio Video Remote
Control Profile) version 1.0 or
above. (Depending on the
Bluetooth device options, some
devices may display AVRCP being
connected for the initial
connection.)
■ The information about the playing
track and the track position will not
be displayed on the Infotainment
system screen.
Cautions for playing Bluetooth audio
■ Do not change the track too quickly
when playing Bluetooth audio.
It takes some time to transmit data
from the mobile phone to the
Infotainment system.
■ The Infotainment system transmits
the order to play from the mobile
phone in the Bluetooth audio play
mode. If this is done in a different
mode, then the device transmits the
order to stop.
Depending on the mobile phone's
options, this order to play/stop may
take some time to activate.
■ If the mobile phone or Bluetooth
device is not in the waiting screen
mode, it may not automatically play
despite being carried out from the
Bluetooth audio play mode.
If Bluetooth audio playback is not
functioning, then check to see if the
mobile phone is in the waiting
screen mode.
■ Sometimes, sounds may be cut off
during the Bluetooth audio
playback. The Infotainment system
outputs the sound from the mobile
phone or Bluetooth device as it is
transmitted.
Bluetooth error messages and
measures
■ Bluetooth deactivated
Check if Bluetooth is activated. The
Bluetooth function can be used
upon activating Bluetooth.
■ Bluetooth is busy
Check if there are any Bluetooth
devices connected. To connect
another device, disconnect any
other connected devices first, and
then reconnect.
■ Device list is full
Check if there are less than
5 registered devices. No more than
5 devices can be registered.
Phone
■ No phone book available
This message will be displayed if
the mobile phone does not support
contacts transmission. If this
message appears after several
attempts, then the device does not
support contacts transmission.
Caution
Hands free phone
Taking calls
When a phone call comes through the
connected Bluetooth mobile phone,
the track currently playing will be cut
off and the phone will ring, displaying
the relevant information.
The message will be displayed
when the transmission of contacts
is supported while information with
a device error is also transmitted.
Update the device again if this
occurs.
■ The phone book is empty
This message is displayed if no
phone numbers are stored in the
mobile phone. This will also be
displayed if the phone log
transmission is supported, but in a
way that is not supported by the
Infotainment system.
■ To reject a call, press the O
button on the steering wheel
remote control or use the
multifunction knob and select
Decline.
To talk on the phone, press the q
button on the steering wheel remote
control or turn the multifunction knob
to move to the answer function, and
then press the multifunction knob.
137
138
Phone
■ While talking on the phone, it is
possible to block the transmitted
sound by selecting the Mute Mic
(mute microphone) item by using
the multifunction knob.
■ While talking on the phone, press
and hold the q button from the
steering wheel remote control to
change to the private call mode
(some phones may not support the
private call mode depending on the
phone's options).
■ When a call is received with the
Infotainment system and Bluetooth
is being connected, there are
mobile phones that do not
automatically change to the private
call mode. This depends on the
original specifications of each
mobile phone.
■ When it is possible to use services
related to a third-party conversation
supported by the communications
service provider through an
application, it is possible to make
calls during a call through the
Infotainment system.
■ While third or more-party
conversations, displaying contents
may differ from practical
information.
Phone
Calling by redial
From the steering wheel remote
control, press the q button to display
the redial guidance screen, or press
and hold the button to display the
caller log screen.
Turn the multifunction knob to select
Yes, and then press the multifunction
knob to make a call.
■ If the mobile phone is not in waiting
mode, your phone might not
support the redial function. This
depends on the mobile phone's
options.
■ When redialling a number, the
connected phone number will not
be displayed.
■ Depending on the mobile phone,
there are cases in which the call is
made through the call history of the
received or missed calls instead of
the redial mode. This depends on
the mobile phone's options.
139
Calling by outgoing call log
To make a call by the outgoing call
log, press and hold the q button on
the steering wheel remote control and
turn the multifunction knob to select
the desired call list, then press the
multifunction knob.
Press the multifunction knob while the
phone is connected to display the
connecting functions as shown
below.
Use the multifunction knob to use the
functions in the menu that appears.
140
Phone
Calling by entering numbers
To make a call by entering the phone
number, press the multifunction knob
and turn the multifunction knob to
select Enter number, and then press
the multifunction knob.
Turn the multifunction knob to select
the desired letters, and then press the
multifunction knob to enter the
number.
After the telephone number has been
fully entered, turn the multifunction
knob to move to y and then press the
multifunction knob to start dialling.
To cancel the dialling process, press
the multifunction knob.
Use the phone book for entering the
phone number.
(1) Move: Move input position
(2) Delete: Delete entered character
(3) Phone book: Search contacts
(usable after updating the phone
numbers)
(4) Dial: Start dialling
■ Repeat this procedure to enter all
telephone numbers.
■ Press the P BACK button to delete
a letter one by one, or press and
hold the button to delete all content
that has been entered.
■ Refer to the following contents to
edit the input contents.
Turn the multifunction knob to select
Phone book, and then press the
multifunction knob to enter the
Search function (see below).
Phone
Using the Phone Menu
Phone Menu → Phone book → Search
141
Turn the multifunction knob to select
First Name or Last Name, and then
press the multifunction knob.
To end a call, turn the multifunction
knob to choose Hang up, and then
press the multifunction knob.
Press the multifunction knob, turn the
multifunction knob to select Phone
book, and then press the
multifunction knob.
A notification will appear on screen,
with no contacts to use, and you will
be returned to the previous menu.
Turn the multifunction knob to select
Search, and then press the
multifunction knob.
Turn the multifunction knob to select
the search terms/range, and then
press the multifunction knob.
Turn the multifunction knob from the
search results screen to select the
desired item, and then press the
multifunction knob to view the details
for that item.
Display number types
[iH]: Home
[iM]: Mobile
[iW]: Work
142
Phone
[iO]: Other
To call the relevant number, press the
multifunction knob.
For more information, refer to the
making phone calls item.
Turn the multifunction knob to select
Yes or No, and then press the
multifunction knob to activate or
cancel the update.
Phone Menu → Phone book → Update
Update the contacts of the connected
mobile phone to the system’s
contacts.
Using the multifunction knob, select
Phone Menu → Phone book →
Update, and then press the
multifunction knob.
Notice for updating contacts
■ This function can be used with
mobile phones that support a
contacts update and the call history
transmission function. (If the
product is connected to a mobile
phone that does not support these
functions, the call history can be
displayed through the Infotainment
system.)
■ An update is not supported for more
than 1,000 contact numbers.
■ Be aware that hands-free and
Bluetooth audio playback will be cut
off while proceeding with updates
for contacts (other functions except
for handsfree and Bluetooth audio
playback can be used.)
■ To update your contacts, it is
possible to request for the
transmission certification for
contacts. If the waiting screen does
not change for a long time, you can
check whether the mobile phone is
requesting for certification. When
requesting for certification of the
mobile phone, all Bluetooth
connections will be cut off if it is not
accepted, and then the device will
be reconnected.
■ When receiving the call history, it is
possible to request for the
transmission certification for the
call history from the mobile phone.
If the waiting screen does not
change for a long time, check
whether the mobile phone is
requesting for certification.
When requesting for the
certification of the mobile phone, all
Phone
■
■
■
■
■
Bluetooth connections will be cut
off if it is not accepted, and then the
device will be reconnected.
If there is a problem in the stored
information of the mobile phone,
the contacts may not be updated.
The Infotainment system only uses
information coded in UTF-8 format.
If other operations (game, map
search, navigation, etc.) are
activated during the contacts
update or call history transmission
progress, the update/transmission
process may not work.
This is because other operations
running on the mobile phone are
affecting the data transmission.
When the contacts update or call
history transmission is completed,
all handsfree and Bluetooth audio
play modes will be automatically
disconnected and then
reconnected.
If the Infotainment system gets
turned off while talking on the
phone, the call will be transmitted to
the mobile phone. Some phones
■
■
■
■
may need to setup a call
transmission function beforehand,
depending on the type of the
phone.
If the user disconnects the
connection directly (using the
Infotainment or mobile phone), the
auto connection function does not
take place.
Auto-connection: This function
automatically finds and connects
the device that was last connected.
The contacts may not always
display all the lists on the phone
when selected. The Infotainment
system only displays what has
been transmitted from the mobile
phone.
The contacts update can only
receive four numbers per contacts
directory (mobile phone, office,
home, and other).
Changing the language setup
during the contacts update will
delete all previous updates.
143
■ If the mobile phone is not set with a
waiting screen, calls may not be
made to this Infotainment system.
■ If the OS of the mobile phone gets
updated, it may change how the
phone's Bluetooth function works.
■ Special characters and
unsupported languages will be
displayed as ____.
■ Calls registered in the contacts
without any name will be indicated
as No number in contact.
■ The Infotainment system will
display contacts, call history, and
redial information as it is
transmitted from the mobile phone.
144
Phone
Phone Menu → Phone book → Delete
all
Use the multifunction knob to select
Phone Menu → Phone book → Delete
all, and then press the multifunction
knob.
Turn the multifunction knob to select
Yes or No, and then press the
multifunction knob to delete all
contacts or to cancel.
Phone Menu → Call lists
Check, use, or delete contacts.
Use the multifunction knob to select
Phone Menu → Call lists, and then
press the multifunction knob.
Use the multifunction knob to select
the detailed call history, and then
press the multifunction knob.
Turn the multifunction knob to check
the call history and to make a call.
Press the multifunction knob to call
the selected number from the call
history.
■ If the Please wait screen continues
to be displayed for too long after
selecting the call log, check if the
mobile phone is requesting
verification for the transfer of call
numbers. After completing the
mobile phone verification
Phone
145
procedures, the contacts and the
call log will be transmitted to the
Infotainment system.
■ The call log from the mobile phone
and the log displayed on the
Infotainment system may be
different. This Infotainment system
shows the information transmitted
from the mobile phone as it is.
Phone Menu → Bluetooth settings
Setup the Bluetooth function.
To activate the Bluetooth function,
register, connect or delete the
Bluetooth device or change the
Bluetooth code, choose Bluetooth by
using the multifunction knob, and
then use the multifunction knob to set
up the desired item.
Using the multifunction knob, select
the Phone Menu → Bluetooth
settings, and then press the
multifunction knob.
To set up the ring tone and its volume
used by the Bluetooth function, use
the multifunction knob to select
Sound & Signals, and then set up the
desired items with the multifunction
knob.
146
Phone
To reinitialise the Bluetooth settings
to their default values, use the
multifunction knob to select the initial
setup restoration item, and then
select Yes with the multifunction
knob.
Phone
147
148
Index
A
Auxiliary devices ........................ 125
B
Bluetooth® ................................. 132
C
CD player ................................... 117
Control elements overview........... 94
F
Fixed mast antenna.................... 116
G
General information...................... 92
H
Hands free phone ...................... 137
O
Operation ..................................... 96
P
Personalisation........................... 100
R
Radio data system (RDS) .......... 112
T
Theft-deterrent feature ................. 93
U
Usage......................................... 104
Download PDF