wDALI Controls

wDALI Controls
Datasheet
DALI RF Remote Control
Wireless control of DALI systems
Art.Nr. 86459587-TR (Transceiver)
Art. Nr. 86459534-W (Remote white)
Art. Nr. 86459534-B (Remote black)
Art.Nr. 89453848 (MC)
Art.Nr. 86459541-W (Switch white)
Art.Nr. 86459541-B (Switch black)
combo transmitter/receiver:
Art. Nr. 86459534-W+T (Remote white +Tr.)
Art. Nr. 86459534-B+T (Remote black +Tr.)
Art.Nr. 89453848+T (MC +Tr.)
Art.Nr. 86459541-W+T (Switch white +Tr.)
Art.Nr. 86459541-B+T (Switch black +Tr.)
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
wDALI Controls
2
wDALI Controls
Wireless DALI Controls
Overview
•
•
•
•
•
•
•
•
Wireless control of a DALI-line
A wDALI control consist of at least two
components – the freely placeable
user interface (input device) and a
transceiver, which has to be
connected to the DALI signal line
Available input devices: Remote (12
buttons), Switch (4 Buttons) and MC, a
pushbutton coupler with 4 potentialfree inputs (pushbuttons only)
•
•
•
•
•
Up to 4 effective ranges, switching
mode and DALI-command can be
assigned to each pushbutton.
•
Factory default setting offers basic
control functions
•
Individual addresses (0-63), group
addresses (0-15) or broadcast can be
set as effective range.
•
Various switching modes (short, long
press; toggle; stairways function etc.)
can be assigned to each pushbutton.
Configurable power up function
Memory function for brightness
Simple installation and configuration
with the DALI-Cockpit software tool
Multiple input devices can be paired
with the same transceiver (FWVersion 2.0 and higher), each paired
device has the same function.
A input device can be paired with
several transceivers in order to control
multiple DALI-lines
Multiple wDALI-transceivers can be
used on the same DALI signal line.
The transmitter part (input device can
be placed anywhere in the radio
receiver range.
The transceiver must not be
connected to the mains. It is supplied
directly via the DALI signal line.
DALI DT8 support for adjustable white
luminaires
typical installation (several input devices, one transceiver)
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
3
typical installaiton (one input device, simultanous conrol of multiple DALI-lines)
Specification, Characteristics
type
article number
electrical data:
supply
typ.current
consumption
output
function after power
return
frequency range
wDALI Transceiver
86459587-TR
via DALI signal-line
3.8mA
DALI
programmable
2,4 Ghz
receiving range
up to 300m (outdoors)
technical data:
dimensions
59mmx33mmx15mm
housing/mounting
connecting wire cross
section
ambient temperature
protection class
wDALI Controls, Datasheet
back box
0.5 to 1.5 mm
2
-10°C…+50°C
IP20
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
4
type
article number
wDALI
Switch Cross
86459541-W (white)
86459541-B (black)
electrical data:
supply
estimated battery
lifetime
output
wDALI MC
86459534-W (white)
86459534-B (black)
89453848
battery
6 years
2,4Ghz RF
4 pushbuttons
12 pushbuttons
4 potential free inputs for
pushbuttons
82mmx82mmx8,5mm
140mmx52mmx10mm
40mmx28mmx15mm
wall mounting
-
back box
inputs
technical data:
dimensions
wDALI Remote
housing
connecting wire cross
section
ambient temperature
protection class
2
-
0.5 to1.5 mm
-10°C…+50°C
IP20
geometry MC (input device)
geometry transceiver (receiver)
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
5
geometry switch (input device)
geometry remote (input device)
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
6
Installation
•
•
wDALI Transceiver is supplied by the
DALI-line (typ. current consumption
3.8mA)
the connection to the DALI-line is
polarity free
•
the DALI-input is protected against
overvoltage (up to mains voltage)
•
the wDALI transceiver is suitable for
back box mounting
•
input devices can be placed within the
receiver range (dependent on
structural conditions, outdoors up to
300m)
Function
•
Simple addressing and configuration
with the DALI Cockpit software tool
•
Simple Pairing/Unpairing of additional
input devices
•
The function assigned to a button can
be recalled by each of the paired input
devices (Switch&MC: Button 1-4,
Remote: Button 1-12)
•
Factory setting (Preset1) can be
restored at any time
•
Preset 2 for tunable white mode can
be configured quickly
•
Individual configuration for each
button
•
Command selection from DALI
command set, predefined and
customized macros
•
Predefined macros for dynamic and
sequential recall of scenes, tunable
white control and memory function
•
Adjustable power up function (no
change, Off, scene 0-15)
•
Operating modes for interacting with
a central control unit
Hint: only pushbuttons may be connected to the wDALI MC. Do not connect switches!
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
7
Preset1: Switch&Dim (factory default)
MC – input 1: Recall Max
MC – input 2: Dim Up
MC – input 3 : Off
MC – input 4: Dim Down
wDALI Controls, Datasheet
Preset2: switch, dim & tunable white
MC – input 1 short: Recall Max
MC – input 1 long: Dim Up
MC – input 2: Cooler
MC – input 3 short : Off
MC – input 3 long: Dim Down
MC – input 4: Warmer
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
8
Pairing (supported by firmware 2.0 and higher) : Add/Remove input device, all paired input devices are shown in
the DALI Cockpit
The pairing number of the input device can be found on the round sticker on the backside of the input device
(e.g. see DALI Switch below):
The active button is always shown on all paired input device types:
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
9
Settings for Switching function of a pushbutton:
Definition:
Key
Definition
short
long
buttonfunction
Duration
min
40 ms
>400 ms
max
400 ms
key press
release after
short press
long press
repeat
remarks
0
1
2
CmdX
CmdX
-
CmdY
-
3
CmdX
-
CmdY
CmdY
4
-
-
-
-
-
-
CmdX/Y depending on bus status
6
CmdX /
CmdY toggle
CmdX /
CmdY toggle
-
sends CmdX on key press
sends CmdX on key press
sends CmdY after long press delay
sends CmdX on key press
sends CmdY with 200ms repetition after long
press delay
sends CmdX and CmdY alternating on key press
CmdX / CmdY
toggle
ON and
STEPUP
UP / DOWN
7
8
9
CmdX
-
-
-
10
11
CmdX
CmdX
-
CmdY
-
CmdY
CmdY
12
CmdX
CmdY
-
CmdX
CmdX/Y depending on bus status, UP/DOWN
alternating, ON AND STEPUP, if bus state is OFF
before UP
Staircase control. CmdY is sent after a
programmable delay.
CmdX after short press, CmdY for repeat
CmdX with repeat; repeats CmdY without long
press delay
CmdX with repeat; if button is released within
short press time, CmdY is finally sent
5
Hint: When using overlapping areas a correct evaluation of the state of the areas cannot be
guaranteed
Hint: DALI commands are always sent to all effective ranges assigned to a key.
Settings for CmdX/CmdY
CmdX and CmdY represent DALI commands or sequences of DALI commands which are sent on the
DALI-line after the corresponding switching action has occurred. CmdX and CmdY can be:
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
10
•
•
•
DALI commands
Predefined macros (command sequences)
Custom macros
DALI-Commands:
CmdNr
0
1
2
3
4
5
6
7
8
10
16-31
Command name
DIRECT ARC POWER
OFF
UP
DOWN
function
Direct set of the light level in %
Off
Dim up (using faderate)
Dim down (using faderate)
STEP UP
STEP DOWN
RECALL MAX
RECALL MIN
STEP DOWN AND
OFF
Increases light level by one increment
Decreases light level by one increment
Recalls maximum value
Recalls minimum value
Decreases light level by one increment, if light level is already at minimum
switch off
Switch on light to minimum if it is off, otherwise increase level by one
increment
Switch to last active level (supported by DALI2 compatible ballasts, firmware
version 2.0 and higher)
Recall scene 0-15
ON AND STEP UP
GOTO LAST ACTIVE
LEVEL (DALI 2)
GO TO SCENE
Macros:
MacroNr
M1
M2
M3
M4
M5
M6
M7
Macro (required
memory)
Go Home
(2 Byte)
Sequential Scenes
(3Byte)
Dynamic Scenes
(33 Byte)
DALI-Reset
(1 Byte)
User Defined Cmd-List
(5 Byte je Befehl,
19 Befehle max.)
3x Cooler (DT8)
(0 Byte)
3x Warmer (DT8)
(0 Byte)
M8
Memory Switch On
(4 Byte)
M9
M10
Memory Switch Off
(3 Byte)
Memory Dim Up
(after Switch Off)
(3 Byte)
wDALI Controls, Datasheet
Function
Light dims down to DAP 0 with predefined fade time, then fade time is set
back to a programmable value
Selectable scenes (or OFF) will be sent sequentially with each button press
Dynamic sequence of up to 16 scenes, fadetimes and delays (0…254s) can
be configured, stops with next button press
Sends DALI-Reset (address can be deleted optionally)
A user defined macro file can be loaded
Activates DT8 and sends STEP COOLER command 3x
Activates DT8 and sends STEP WARMER command 3x
MEMORYFUNCTION
recalls last used level, only works in combination with Switch Off macro
(firmware version 1.8 and higher)
MEMORYFUNCTION
Stores the actual value in the ballast and switches off (firmware version
1.8 and higher)
MEMORYFUNCTION
Macro for dimming up if Switch Off Macro has been used before (firmware
version 1.8 and higher)
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
11
Hint: The available macro memory of 96 bytes per button (button 1-4) must not be exceeded.
For button 5-8 and button 9-12 a total macro space of 192 bytes is available (the required
memory for each macro is mentioned in the second column of the macrotable)
Memory Function
wDALI-Controls support different methods of
memory function for brightness.
Method 1: Macro M8-M10, the actual level is
stored as MAX-Level before the ballast is
switched off. When switching on by using
Recall Max the stored level (=last active level)
is recalled. The old Max-value is restored
finally.
Method 2: Support of DALI 2.0 command Nr.
10 - GOTO LAST ACTIVE LEVEL. Suitable only
for Ballast, which already support this
command (firmware 2.0 and higher)
Method 3: As alternative scenes can be used
for storing the last level temporary. Before
switching off the actual value has to be stored
as scene value. Switching on to the last active
level can then be realised with recalling the
corresponding scene.
DALI-Cockpit
With the help of the DALI Cockpit the
mentioned functions can be configured for
each button separately.
In the settings for each button there are 2
parts: the effective range (destination
address) and the function (button function
and its configuration options)
Operating Modes
Three operation modes are supported, one of
them for direct control of DALI ballasts
(master mode) and 2 others for operation in
combination with a central controller (slave
mode, event message mode).
Master Mode (Default)
In this operating mode the wDALI-device acts
as DALI control device on the DALI-line and
sends event based DALI-commands directly to
the ballasts (as configured).
Event Message Mode
In this mode predefined proprietary
commands are sent on the DALI-line on
button press. They can be evaluated by a
central controller. In this mode DALIcommands are not sent directly to the
ballasts.
Hint: Any command (DALI or
proprietary extension) can be
generated in master mode using user
defined command lists (macro M5).
Hence a custom solution for event
messaging can be realized.
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
12
Slave Mode
The slave mode is a passive operating mode.
The wDALI Control does not send commands
by its own, it only replies on requests.
The operating mode can be set in the DALICockpit.
Additional Information and
Equipment
DALI-Cockpit – free configuration tool from
Lunatone for DALI systems
http://lunatone.at/en/downloads/Lunatone_
DALI-Cockpit.zip
Lunatone DALI products
http://www.lunatone.at/en/
Lunatone datasheets and manuals
http://lunatone.at/en/downloads/
Contact
Technical Support: support@lunatone.com
Requests: sales@lunatone.com
www.lunatone.com
Purchase Information
Transceiver:
Art.Nr. 86459587-TR wDALI Transceiver, base
unit – connected to the DALI-line, can be
paired with several input devices
Disclaimer
Subject to change. Information provided without guarantee.
The datasheet refers to the current delivery.
The compatibility with other devices must be tested in advance
to the installation.
Input devices:
Art. Nr. 86459534-W Remote white, 12
buttons
Art. Nr. 86459534-B Remote black, 12 buttons
Art.Nr. 89453848 MC, 4 inputs
Art.Nr. 86459541-W Switch white, 4 buttons
Art.Nr. 86459541-B Switch black, 4 buttons
Combination (Transceiver and Input devices):
Art. Nr. 86459534-W+T Remote white+Trans.
Art. Nr. 86459534-B+T Remote black +Trans.
Art.Nr. 89453848+T MC+Transceiver
Art.Nr. 86459541-W+T Switch white+Trans.
Art.Nr. 86459541-B+T Switch black+Trans.
wDALI Controls, Datasheet
© 2017/04/28, Lunatone Industrielle Elektronik GmbH
Download PDF