SLP 4-6D single-mode test kit with Wave ID and set

SLP 4-6D single-mode test kit with Wave
ID and set reference
Features
• Rugged, handheld, lightweight
• Designed for field use
• Certify single-mode links per TIA/EIA
standards
• Wave ID - automatic wavelength identification and switching
• Dual Wave ID, single Wave ID, CW, and
modulated Tone (on single-mode output)
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone
• Adjustable output
• Large LCD with Backlight
• Power measurements in dBm or µW;
insertion loss in dB
• Reference power level storage
• AA alkaline, optional rechargeable NiMH
battery pack or AC adapter
• Low battery indicator
• Cost-effective, easy to use
• N.I.S.T traceable
The SLP 4-6D test kit combines the OPM 4-4D optical power meter and OLS 2-Dual
LASER light source and is ideally suited for testing single-mode fiber optic networks.
The OLS 2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and is easy to operate. The LASER output is stabilized to ensure accurate test results
per current TIA/EIA requirements. This light source offers 4 modes of operation: Dual
wavelengths sending ID, single wavelength sending ID, CW, and modulated Tone. [Active
Output], [Tone], [Battery], and [External Power] indicators identify the currently enabled
operating mode, battery charge status, and external power presence. The output port is
equipped with a removable SC (FC & ST available) adapter to allow the output connector to
be inspected and cleaned.
The OPM 4-4D offers Wave ID, automatic wavelength identification and switching, when
used with the OLS 2-Dual. Multiple test Tone detection is provided for fiber identification. The OPM 4-4D stores optical references for each calibrated wavelength. An easy to
read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or
insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery
charge status.
In addition to being powered by two AA alkaline, the OPM 4-4D or OLS 2-Dual can be
powered by optional AC adapter and/or rechargeable NiMH battery pack.
The OPM 4-4D optical input port accepts Noyes thread-on style adapter caps. Adapter
caps are required for operation and must be ordered separately.
The OPM 4-4D and OLS 2-Dual are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP 4
OLS 2-Dual optical light source, OPM 4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
Test & Inspection
© 2002, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision A, 6.28.05
Specifications are subject to change without notice.
1
SLP 4-6D single-mode test kit with Wave ID and set reference
OLS 2 - Dual specifications
Optical
OLS 2-Dual (single port)
Output wavelength
1310 ±20 nm, 1550 ±20 nm
0 dBm*
Output power
Laser classification
Class 1 (FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1)
Output connector
SC (FC & ST available)
Spectral width (FWHM)
5 nm (max)
Stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
General
Power
2 x AA batteries, optional NiMH or AC adapter
Battery life (2 x AA)
Typical 120 hours, Minimum 75 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.65 lb (.29 kg)
* Adjustable
2 dB.
All specifications at 25°C.
OPM 4-4D specifications
Optical
OPM 4-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850 nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
General
dB, dBm, µW
Power
2 x AA batteries, optional NiMH
Battery life (2 x AA)
300 hours with backlight [Off]
20 hours with backlight [On]
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Test & Inspection
© 2002, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision A, 6.28.05
Specifications are subject to change without notice.
2
Download PDF