Installation height of the outdoor camera

Outdoor MotionViewerTM
DCV
I N S TA L L ATI O N DATA S H E E T
Made by RSI VIDEO TECHNOLOGIES
Installation height of the outdoor camera :
2m80 to 3m (9’ to 9 1/2’) to the bottom of the camera
The outdoor MotionViewer detector DCV250/DCV650/
DCV750 is integrated with filters and analytical levels which
enables it from untimely triggering on with the presence of
small animals : rabbits, cats, birds.... However, dogs, foxes
and wild boars can be detected.
Base
Screw cover
for the base
Screw + Allen
key
Wing screw
It is highly recommended to use a camera head kit (no Kodak
screw) or our MB100 camera kit to fix the camera, indeed,
if you bore a hole in the lower stand of the camera, its
waterproofness will be lost...
Composition of the MB100 kit
- Base stand with screw cover.
- A camera head enabling a 360° orientation of the camera
with a wing screw (or Allen screw supplied with its key).
- Two extension cords - 5 cm each. Camera fixing screw
(diameter 6.35 mm - 20 threads per inch).
Extention
5 cm (2 1/2
inches)
Clamping
ring
Base
Indicator LED
Camera
Infrared LED for night vision
DCV means DCV650 for USA/Canada, DCV750 for Australia/Singapore
and DCV250 for Europe and rest of the world.
Clamping screw for camera
Ball pivot
360°
Outdoor MotionViewerTM DCV
I N S TA L L ATI O N DATA S H E E T
Back wall
Recording of the detector
The alarm panel must be put in "Recording device
mode", and the keypad must display“PRESS
PROGRAM BUTTON OF DEVICE”.
1
Insert the 3 Lithium batteries LS14500 (in the same directions).
2
Press the PROGRAM BUTTON of the camera detector, release as soon as the indicator flashes.
3
Carefully place the block camera on its base and screw down the 4 clamping screws.
4
Fix the base of the ball and socket head on a desired height and place (while respecting fixing height.
5
Place the screw cover on top and screw down the ball pivot.
6
If need be, use extentions then screw them down to the camera detector on the top of the ball and socket head (or extentions) and screw down the ring of the ball and socket head in order guarantee adequate fixing.
7
Finally, direct the camera as required and tighten with wing screw or Allen screw (to be used instead of the wing screw).
Location of the ball pivot,
camera fixing screw
Camera block
8 Test the RF range (RSSI level at 20 seconds).
9
Allocate an area (with direction arrows of the keypad) and validate with the [YES] key.
10 Name the device.
11 Test the detection coverage area.
> Possibility of testing RF cover (minimum radio level at 20).
> Possibility of testing the detection cover range.
* This indicator will no longer flash from then on except at
opening, arming or during a detection test.
Self protection
of the camera
Program Button
DCV means DCV650 for USA/Canada, DCV750 for Australia/Singapore
and DCV250 for Europe and rest of the world.
North American Headquarter
EMEA SALES
2, rue Alexis de Tocqueville
92160 ANTONY
FRANCE
Hot line : +33 (0)820 846 620 / UK : 0871 951
Fax : +33 (0)3 90 20 66 36
4455 White Bear Parkway, Suite 700
White Bear Lake, MN 55110
USA
Hot line : 877-206-5800
Fax : 651-762-4693
www.videofied.com
© 2009 RSI VIDEO TECHNOLOGIES. VIDEOFIEDTM is a Registered Trademark of RSI VIDEO TECHNOLOGIES.
Specifications subject to change without notice.
Download PDF