LINK HDEXT1IR232_manual-update

HDMI PIN DEFINITION

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

TMDS Data2+

TMDS Data2 Shield

TMDS Data2–

TMDS Data1+

TMDS Data1 Shield

TMDS Data1–

TMDS Data0+

Pin 8

Pin 9

Pin 10

Pin 11

Pin 12

Pin 13

Pin 14

Type A (Receptacle) HDMI

TMDS Data0 Shield

TMDS Data0–

TMDS Clock+

TMDS Clock Shield

TMDS Clock–

CEC

Pin 15

Pin 16

Pin 17

Pin 18

Pin 19

Reserved(N.C. on device)

SCL

SDA

DDC/CEC Ground

+5V Power

Hot Plug Detect

NOTICE

1.

2.

All HDMI over CAT5 transmission distances are measured using

Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video

Signal Generator VG-859C & VG-870B.

Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in

3.

the damage.

The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI sources, and the type of HDMI display. The

4.

UTP cables (usually in the form of fixed length patch cords). solid UTP Cat-5e cable shows longer transmission range than

UTP/STP cables are the only viable choice.

5.

6.

To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable, one can use shielded STP cables to improve EMI problems, which is worsen in long transmission.

Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality, the actual transmission range is subject to than 1080i or 1280x1024, a Cat-6 cable is recommended.

7.

transmission performance among all HDMI inputs.

Performance Guide for HDMI over Category Cable Transmission

Wiring

Performance rating

Shielding

Unshielded (UTP)

Solid

Stranded

Shielded (STP)

Unshielded (UTP)

Shielded (STP)

Termination

Type of category cable

CAT5



CAT5e



CAT6





















Please use EIA/TIA-568-B termination (T568B) at any time

HARDWARE INSTALLATION

1.

Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the

2.

5.

6.

3.

4.

Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit HDEXT1IR232-RX.

Connect IR Blaster/Receiver to both TX and RX units.

receiving units.

Plug in 5V DC power supply unit to the power jack of the receiving

WARRANTY

with

The SELLER warrants the HDEXT1IR232 HDBasedT Lite Extender

free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working order the unit, provided that the unit has not been subjected to accident, discharge and power surge. This warranty is offered by the SELLER for its seal on the metal housing is broken.

repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit.

Under no circumstances will a unit be accepted without a return disclaimed.

Proof of sale may be required in order to claim warranty.

Customers outside Taiwan are responsible for shipping charges to and from the SELLER. Cables and power adapters are limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled.

The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER advised of the possibility of such damages. Also, the technical

HDEXT1IR232 features and and the HDMI logo are trademarks of HDMI Licensing LLC in the United

States and other countries.

User Manual

Safety and Notice

The HDEXT1IR232 HDBasedT Lite Extender with

& RS-232

However, like all electronic equipments, the HDEXT1IR232 should be used with care. Please read and follow the safety minimize the risk of damage to the unit.

explained in this manual.

water.

Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.

cables designed for this unit.

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

INTRODUCTION

The

HDEXT1IR232 HDBasedT Lite Extender with

Bi-directional IR & RS-232

boosts up your video/audio transmission distance up to 60m (198ft) in HDTV 1080p with 48-bit color depth.

HDEXT1IR232 also supports the most advanced 3D video format complaint with HDMI specification and therefore guarantees the highest 3D video compatibility on the market. With only one cost effective CAT5/5e/6 cable, users can readily extend HDTV sources from

DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display monitors including

HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the latest HDMI technology, deep color video, DTS-HD or

Dolby TrueHD audio, and HDCP supports and compatibility are all further insured. This flexibility makes HDCP compliant DVD players or

PS3 transmit utmost high quality video and audio with a greater distance at the minimal cost, when integrating several components apart. In addition, HDEXT1IR232 is also equipped with bi-directional IR pass-through path and RS-232 serial port control. These bonus features allow users to boost IR control distance up to 60m (198 ft) and makes IR control possible through only single CAT5/5e/6 cable including HDMI signals. In addition, serial port offers the convenient path for interactive application, such as touch panels.

The HDEXT1IR232 includes two units: transmitting unit

HDEXT1IR232-TX and receiving unit HDEXT1IR232-RX. The transmitting unit is used to capture the input HDMI / DVI signals with IR control packets and carry the signals via one cost effective CAT5/5e/6 cable.

The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR signals. HDEXT1IR232 offers the most convenient solution for digital signage with long distance A/V transmission path, and with 10G transmission width ready,

HDEXT1IR232 is ready for your next HDMI generation and applications!

i

FEATURES

Support HDMI Deep Color & full 3D & 4K2K@30 (HDBaseT-Lite technology)

Extend the transmission up to 60m (198ft) from the HDMI source at

Full HD 1080p 48-bit and 40m (130ft) at 4K2K@30

HDCP & EDID Bypass

CEC support

Auto equalization

Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission

DTS-HD Master Audio and Dolby TrueHD high bit rate audio support

Support full frequency IR signal from 20KHz to 60KHz

Bi-directional IR path-through

Full Duplex RS-232 control up to 115,200 bps through connector

Wall mounting housing design for easy and robust installation

The length depends on the characteristics and quality of the cables.

Higher resolutions and longer transmission distances require low skew cables (<25ns/100m) for best performance. Unshielded CAT6 with metal RJ45 connectors is recommended.

PACKAGE CONTENTS

1x HDEXT1IR232 [TX&RX]

2x 5V DC power supply

1x User Manual

1x IR blaster

1x IR receiver

SPECIFICATIONS

Model Name

Technical

Role of usage

HDMI compliance

HDCP compliance

Video bandwidth

Video support

HDMI over UTP

Audio support

Equalization

Input TMDS signal

Input DDC signal

ESD protection

PCB stack-up

IR pass-thru

RS-232 support

Input

Output

HDMI source control

HDMI connector

Min DIN connector

RJ-45 connector

Rotary control switch

3.5mm connector

Mechanical

Housing

Dimensions

[L x W x H]

Weight

Model

Package

Carton

Model

Package

HDMI Deep Color, full 3D & 4K2K@30

Yes

Single-link 340MHz [10.2Gbps]

480i / 480p / 720p / 1080i / 1080p60

1080p@60 60m (198ft) [CAT5e]

Surround sound [up to 7.1ch) or stereo digital audio

Auto

1.2 Volts [peak-to-peak]

5 Volts [peak-to-peak, TTL]

[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]

[2] Core chipset — ±8kV

4-layer board [impedance control — differential 100Ω; single 50Ω]

Bi-directional

Yes

1x HDMI

1x 3.5mm

1x RJ-45[HDBaseT]

1x 3.5mm

1x RJ-45[HDBaseT]

1x 3.5mm

1x HDMI

1x 3.5mm

Controllable via IR pass-through from RX to TX with IR extenders

Type A [19-pin female]

DIN-9

WE/SS 8P8C(Reverse Mode)

None

IR receiver / IR blaster IR receiver / IR blaster

HDEXT1IR232-TX HDEXT1IR232-RX

Metal enclosure

73 x 89 x 26mm [2.9" x 3.5" x 1"]

175 x 125 x 216mm [6.8" x 4.9" x 8.5"]

647 x 366 x 237mm [2'1" x 1'2" x 9.3"]

200g [7oz] 196g [6.9oz]

900g [2 lbs]

Fixedness

Power supply

Power consumption

Operation temperature

Storage temperature

Relative humidity

HDEXT1IR232-TX

Transmitter [TX]

HDEXT1IR232

Wall-mounting case with screws

5V 2A DC

3 Watt [max] 7 Watt [max]

0~40°C [32~104°F]

-20~60°C [-4~140°F]

HDEXT1IR232-RX

Receiver [RX]

20~90% RH [no condensation]

PANEL DESCRIPTIONS

Transmitting unit [Receiving unit]

Latch-locking power jack: Connect to 5V

DC power supply

LED: Power indicator

HDMI IN[OUT]: Connects to a HDMI source[Display] with a HDMI male-male cable

IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster

IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver

RS-232: Connect to host/device serial port with a DSUB-9 male-male cable here

Dip Switch: Setup the RS-232 mode for serial communication channel

RJ45: Plug in a CAT5/5e/6 cable that needs to be linked to the transmitter or receiver.

LED: Link indicator

DIP Switch Position

TX & RX

ON [](DTE)

PIN#1

OFF [](DCE)

PIN#2

ON []

OFF []

Description

TxD: The 2 nd

RxD: The 3 rd

pin of RS-232, which is in charge of sending data

pin of RS-232, which is in charge of receiving data

TxD: The 3

RxD: The 2 rd nd

pin of RS-232, which is in charge of sending data

pin of RS-232, which is in charge of receiving data

Firmware Update

Normal

CONNECTION DIAGRAM

IR PASS-THROUGH

IR Extenders

IR Blaster IR Receiver

IR Sockets

IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other end to control the devices corresponding to the IR signals.

IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices.

!

Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. Warranty will not cover the damage.

Definition of IR Earphone Jack

1. IR Signal

2. Grounding

1. IR Signal[20-60 kHz]

2. Grounding

3. Power

IR Blaster IR Receiver i

You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m

(6-ft) may not work.