400ws TTL WithmicroMANUAL

#067M
L
U
400ws TTL
M
E
POWER PACK
D
With microMANUAL
Y
1. Deluxe TTL/TTM Pack operates
full TTL or Manually from
400ws to 6ws.
In TTL Mode Pack must be
connected to a TTL Flash Head
and a TTL compatible camera
with Quantum or Metz module.
E
I
N
2. Recycle Time is 2.5 seconds @
200ws, 1.3 sec @ 100ws.
C
3. Runs from any size Lumedyne
P
0
1
O
R
T
0
R
W
I
A
C
L
L
S
T
TTL Up and Runnin
in 60 Seconds
TTL System
From 3ws to 2400ws
4 200ws or 400ws TTL Power Packs.
4
4
4
4
N
6
The Worlds Fastest
Most Powerful
H
Battery, Vehicle Adaptor or
AC Power Supply.
4. Accepts other Modules
to increase power (Boosters),
and/or decrease recycling time
(High Speed Modules).
5. Will work Two Flash Heads TTL
without special modules or
adaptor cables.
E
Y
F
L
R
E
3
E
4
T
6
6
8
Lumedyne
Phone: (727) 847-5394
Fax: (727) 841-0000
Help Line: 800-lumedyne
800-586-3396
E-mail : info@lumedyne.com
Web : www.lumedyne.com
4
4
4
Attach charged Battery to Pack.
Screw on TTL Flash Head to Pack.
Place the appropriate TTL Module
in the camera’s Hot Shoe.
Connect the Cord of the TTL Module
to the Flash Head.
Push the Switches up on the Power
Pack to the TTL position.
Select the TTL Confirmatone™
On or Off.
(Not MicroManual™)
Make sure Camera and Flash
Head are on.
Go Shoot!
In addition to the Lumedyne System, (TTL Pack, Head, Battery,
Shooting TTL
and Charger) the appropriate Quantum or Metz™Ô TTL Module is
necessary to function between the TTL Camera and the Lumedyne
TTL System.
The back of the Flash Head comes with a Quantum or Metz™
connector.
You can obtain the correct module for your camera from your
Lumedyne Dealer. See list below.
Ô
Quantum # Camera
QF10
Olympus
QF11
Minolta X
QF12
Nikon
QF13N
Canon
QF14
Minolta XI
QF15
Contax
QF16
Leica
QF17
Pentax
QF18
Rollei
QF19
Hasselblad
QF20
Bronica
QF22
Mamiya
QF51
20 ft. Extension Cord
Assuming the Battery, Head and TTL connector are attached, and the
TTL Camera is on, all you have to do is set the White Switchto the top
#2
position. (Micro TTL/A; Red Switch position does not matter.)
The Confirm-A-Tone switchshould also
#5 be set to either the Right
position,Tone, or the center position, No Tone. If switch is in the far left
#5
position, and the White Switch is at the
#2top, then the Pack is in
microManual Mode; not in TTL Mode. To make sure the Pack is in TTL
Mode, push
the White Switch to the
#2top, and make sure the Confirm-ATone Switchis set
#5 to either the Tone On, or Tone Off position.
Manual Operation
#067M Pack have two Manual Modes. Regular Manual operation is
achieved through the use of the two Switches . (Red and #2
White) The
White switch on the right should be in the Middle postition. Then, the Red
switch on the left operates in three positions: 400ws - 200ws - 100ws.
Both Switches are color coded with white area on the label for the
respective positions. While
in the Manual Mode the microManual Switches
on the bottom do not function.
About the Lights
Recycle Light stays
(#1)on during recycling.
The light goes out when the Pack is ready
to shoot.
From time to time the light will flash as the
Pack maintains power.
The OK Light(appears
(# 4) clear) glows
green for a couple of seconds when a
correct TTL exposure was made. It
comes on and stays on when the Pack is
in the microManual mode, as does the
Red Ready Lightnext to(#3)
it.
The Ready Light also(#3)
lets you know
when you are r
eady to make a TTL
exposure by steadily glowing red in
microManual.
MicroMANUAL
1
2
4
5
6
7
3
MicroManual operation, is a Manual Mode achieved
through setting the TTL Switch to the top,
#2 and sliding
Switch all#5
the way to the left, to the color coded section
(red) on the bottom of the label. In this Mode both the OK
4)3)and Ready Lights will come on and stay on.
The left Switch, is a #6
One Stop Increment switch
down to 6ws on the #067M Pack. The right slider Switch
#7 , is a One Stop Fine Tuning Switch, allowing for
adjustments between stops and making the lowest
settings for the Pack
s to be one stop less. (3ws) The
Normal position for the slider Switch , is at the#7
bottom
of the Pack (in the High setting).
Recycle time in microMANUAL is no faster
than 2 frames per second. Taking pictures
Before the unit has fully recycled will result in
incorrect exposures.
During Recycling certain Cameras (Canon
and Hasselblad in particular) will operate the
Lights in a non-traditional manner
.
Download PDF