USER MANUAL
OMX-HDMI-CAT6
HDMI over Single Cat6 Transmission System with Looping Input
Ocean Matrix
812 Kings Highway · Saugerties, NY 12477
www.oceanmatrix.com
OMX-HDMI-CAT6
HDMI Extender
The Ocean Matrix OMX-HDMI-CAT6 extends high definition audio/
video transmission beyond the standard distances of HDMI cable and
its inherent limitations. Consisting of a transmitter and a receiver, this
system delivers a full 1080P HDMI signal up to 197 feet over a single
CAT6 network cable.
The transmitter features a built-in looping HDMI output for local display
and monitoring. IR signal transmission allows for remote control of the
source at a secondary location via included IR extension cables.
Includes
 One transmitter
 One receiver
 Two 5VDC power adapters
 One IR blaster extension cable- 3.28 ft (1m)
 One IR receiver extension cable - 3.28 ft (1m)
Specifications
Supported Resolutions
480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz,
1080p@50/60Hz
Network Cable
Low resistance and consumption oxygen-free
copper core UTP or STP
Transmission Range
1080p resolution up to 197 feet (60m)
IR Remote Control
Supports 20~60KHz standard IR remote controls
Power Supply
5VDC/1A
Power Consumption
Transmitter 3W, Receiver 2W
Working Temperature
32°F - 140°F (0℃- 60℃)
Dimensions (LxWxH)
2.82x2.62x0.97in (71.6x66.6x24.8mm) per unit
Weight
Transmitter 2.93 lb., Receiver 2.84 lb. (83g/80.6g)
Ocean Matrix OMX-HDMI-CAT6
Page 2
OMX-HDMI-CAT6
Installation Requirements
1. HDMI source device such as a video camera, media player,
monitoring equipment or computer.
2. HDMI display device such as an SDTV, HDTV, or projector with
HDMI port.
3. UTP/STP Cat6/6A/7 cable, in accordance with the IEEE-568B
wiring standard.
OMX-HDMI-CAT6 Installation Safety
1. Identify the receiver and the transmitter in order to make proper
connections during installation.
2. Do not hot plug/swap when in operation.
3. Use 5VDC power supply only.
Ocean Matrix OMX-HDMI-CAT6
Page 3
OMX-HDMI-CAT6
HDMI to RJ45 Transmitter
1
4
2
5
3
6
7
1 HDMI Signal Output
2 HDMI Signal Indicator LED
- HDMI signal input—on
- No signal—flashes
3 HDMI Signal Input
4 IR Signal Output
- Connect IR blaster extension cable
5 RJ45 Signal Output
6 Reset Button
7 5VDC Power Input
Ocean Matrix OMX-HDMI-CAT6
Page 4
OMX-HDMI-CAT6
RJ45 to HDMI Receiver
1
4
2
5
3
6
1 Reset Button
2 RJ45 Signal Input
3 RJ45 Indicator LED
- HDMI signal transmission—on
- No signal—flashes
4 5VDC Power Input
5 HDMI Signal Output
6 IR Signal Input
- Connect IR receiver extension cable
Ocean Matrix OMX-HDMI-CAT6
Page 5
OMX-HDMI-CAT6
Installation Procedures
Cat6 Network Cable—follow the IEEE-568B wiring standard:
1.
2.
3.
4.
5.
6.
7.
8.
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Connection
1.
2.
3.
4.
5.
Connect TX HDMI input to source device HDMI output
Connect TX HDMI output to HDTV HDMI input
Connect TX CAT6 to RX CAT6
Connect RX HDMI output to HDTV HDMI input
Turn the power ON
DDVD
VD
H D M IInIN
HDMI
HHDMI
DM I O
UT
Out
TTV
V
HDM I to RJ45 sender TX
HDMI to RJ45 sender TX
C AT 6Cable
C a b le
CAT6
RJ45
I receiver
RX RX
RJ45totoHDM
HDMI
receiver
H D M I Out
OUT
HDMI
TTV
V
Ocean Matrix OMX-HDMI-CAT6
Page 6
OMX-HDMI-CAT6
IR User Guide
1. Plug the IR blaster extension cable into the IR-OUT port of the
Transmitter TX.
2. Plug the the IR receiver extension cable into the IR-IN port of the
Receiver RX.
3. Place the emitter of the IR blaster as close as possible to the IR
receiver of the signal source device.
4. Direct the IR remote controller of the signal source device towards
the IR receiver (connected to the RX of HDMI extender), to remote
control source media playback.
Troubleshooting
No image/audio output or degraded signal

Press RX RESET button to reset the device.

Use a shorter network cable.
RX LINK LED is flashing consistently

Ensure the network cable connection follows IEEE-568B
wiring standard.

Ensure TX has an HDMI signal input.

Reset TX & RX and reconnect.
RX LINK LED is on but there is no image output

Press RX RESET button to reset the device.

Ensure the HDMI cable is correctly connected.

Ensure you are using a CAT6 network cable.
Ocean Matrix OMX-HDMI-CAT6
Page 7
SAFETY PRECAUTIONS
1. To prevent fire or shock hazard, do not expose this equipment to high
humidity and/or dust. Do not use in an unprotected outdoor installation
nor any area classified as overly damp or wet.
2. The temperature for installation should be kept between 32°F to 140°F
(0°C to 60°C). Avoid direct sunlight exposure or extreme changes of temperature over a short period of time.
3. Do not disassemble the unit or place it on an unstable base.
4. Do not drop the unit and avoid heavy impact.
5. This unit should not be permanently installed unless proper ventilation is
provided. Any enclosure openings must not be blocked or covered as
they protect the unit from overheating.
6. Before cleaning, turn off the power and unplug the unit from all connections. Use a damp cloth. Do not use liquid cleaners nor aerosol cleaners.
7. Do not overload outlets and extension cords as this may
result in a risk of fire or electric shock.
8. Enclosure entry is dangerous. Never push objects of any kind, including
liquids, into this unit through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.
9. Do not attempt to open or service this unit yourself as
opening or removing covers may expose you to dangerous voltage and
other hazards.
10. There are no user-serviceable parts inside the unit. If the unit requires
service contact your authorized dealer, or an
authorized repair service company.
Ocean Matrix
812 Kings Highway
Saugerties NY 12477
www.oceanmatrix.com
Download PDF