BACnet®/IP to MS/TP Adapter
Overview
The BACnet/IP to MS/TP adapter is a convenient device
used to connect a laptop to an MS/TP network. All the
electronics are provided in a lightweight, small plastic
case. The unit is powered from a USB port. This small
device can easily be carried from jobsite to jobsite in a
laptop bag utilizing a CAT5e cable for communication
and USB cable for power. No batteries or wall plug are
required.
The adapter routes messages between BACnet/IP and
BACnet MS/TP networks as per the ANSI/ASHRAE 135
(ISO 16484-5) standard. It allows BACnet/IP devices
connected over Ethernet to communicate with MS/TP
devices. The adapter is configurable via its web page.
Applications
 Connect to MS/TP network using a notebook or PC
 Commission devices before your network is up and running
 Lightweight portable plastic case for inclusion in integration
kit
 Connect directly to a Distech Controls field controller using
the provided cable
A resident web server allows commissioning, reconfiguration and troubleshooting with a standard web
browser. A reset switch is provided on the adapter to set
the unit to factory default IP address. Three LEDs are
provided: the power LED glows green when proper
power is provided. A bi-color Ethernet LED glows green
for 100 Mbps operation and yellow for 10 Mbps and
indicates activity by flashing. A green LED flashes when
valid MS/TP traffic is received.
The adapter is shipped with a 5-foot CAT5 cable, a 6foot USB cable and a 10-foot cable specifically designed
to connect directly to Distech Controls field controllers.
Each unit compiles with Class A radiated and conducted
emissions as defined by EN55022 and CFR 47, Part 15.
Features & Benefits
®
®
 Route between BACnet /IP to BACnet BACnet MS/TP
networks
 Web server for commissioning, re-configuring and
troubleshooting
 Diagnostic LEDs include MS/TP traffic monitor
 10/100 Mbps Ethernet auto-negation and automatic
medium-dependent interface crossover port
 Optically isolated MS/TP communication port
 Powered through USB port
Product Warranty & Total Quality Commitment
All Distech Controls product lines are built to meet rigorous quality standards and carry a two-year warranty. Distech
Controls is an ISO 9001 registered company. Distech Controls' products provide both the contractor and the end user with
the flexibility of using “best-of-breed” products in system design.
Available Models
PDICC-BASRTPBXX
BACnet/IP to MS/TP Adapter
- Connect a laptop PC directly to the MS/TP trunk
- Commission devices before the network is up and running
Product Specifications
www.distech-controls.com
Power
Input:
Voltage:
Current
Power Consumption:
Environmental
Operating Temperature:
Storage Temperature:
Relative Humidity:
Protection
Enclosure
Material:
Color:
Dimensions (W x H x D):
Installation:
Interface
Port:
Compliance:
Data rate:
Physical Layer:
Max Cable Length:
port Connector:
LED Indicators:
Regulatory Compliance
CE:
CFR
USB (Type B Port)
5 VDC (nominal)
300 mA (typical)
2.5 W
0oC to 60oC; 32oF to 140oF
-40oC to 85oC; -40oF to 185oF
10 to 95%, non-condensing
IP30
Plastic
Black
4.25” x 2.63” x 1.26” (108mm x 67mm x 32mm)
USB Plug
Ethernet
IEEE 802.3
10 Mbps, 100 Mbps
10BASE-T, 100BASE-TX
100 m
Shielded RJ-45
Green = 100 Mbps (flash for activity)
Yellow = 10 Mbps (flash for activity)
MS/TP
ANSI/ASHRAE 135 (ISO 16484-5)
9,600; 16,200; 38,400; 76,800 bps
EIA-485
1200 m
3-pin terminal block
Jumper-selectable bias and termination
green = MS/TP (flash for activity)
EN 55022
EC 55024
CFR 47, Part 15 Class A
All materials and manufacturing processes comply with the RoHS directive
.
Specifications subject to change without notice.
Distech Controls is a registered trademark of Distech Controls Inc.;
BACnet is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE);
All other trademarks are property of their respective owners.
*05DI-DSBRTPB-10*
05DI-DSBRTPB-10
BACnet /IP to MS/TP Adapter
www.distech-controls.com
Download PDF