D2550 System Board for TX120

PRIMERGY
System Board D2550
for TX120
Technical Manual
Martin Jung
Fujitsu Siemens Computers GmbH München
81730 München
e-mail: email: manuals@fujitsu-siemens.com
Tel.: (089) 61001-154
Fax: 0 700 / 372 00000
D2550 (TX120)
Sprachen: En
Edition July 2007
Comments… Suggestions… Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2007 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
This manual is printed on
paper treated with
chlorine-free bleach.
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3
Environmental Protection . . . . . . . . . . . . . . . . . . . 11
3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3
PCI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.4
Screen resolution
3.5
Temperature / system monitoring . . . . . . . . . . . . . . . 20
3.6
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.7
3.7.1
3.7.2
Connectors and Jumpers . . . . . . . . . . . . . . . . . . . 23
Settings with jumpers . . . . . . . . . . . . . . . . . . . . . . 24
External connectors . . . . . . . . . . . . . . . . . . . . . . . 25
4
Replacing the lithium battery . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . 20
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
D2550 (TX120)
Technical Manual
1
Introduction
This technical manual describes the system board D2550, which is equipped
with one Intel® processor.
You will find further information in the manual “BIOS Setup”.
Further information about drivers is provided in the readme files on the hard
disk, or on the supplied CDs/DVDs.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
italics
indicates commands, menu items, file and path
names or software programs
fixed font
indicate system output on the monitor
semi-bold fixed font indicates values to be entered through the
keyboard
[Key symbol]
indicates keys according to their representation on
the keyboard
If capital letters are to be entered explicitly, then the
Shift key is shown, e.g. [SHIFT] - [A] for A.
If two keys need to be pressed at the same time,
then this is shown by placing a hyphen between the
two key symbols.
“quotation marks”
indicates names and terms that are being emphasized.
Ê
indicates an operation that to be performed
V CAUTION!
I
indicates warnings, which, if ignored, will endanger
your health, destroy the system or lead to the loss
of data.
indicates additional information, notes and tips
Table 1: Notational conventions
D2550 (TX120)
Technical Manual
5
2
Important notes
In this chapter you will find essential information regarding safety when working
with the system board.
V CAUTION!
With the system board installed you must open the system to access the
system board. How to access the system board of your system is
described in the appropriate service supplement.
When handling the system board, refer to the specific notes on safety in
the operating manual and/or service supplement for the respective
server.
2.1
Notes on safety
V CAUTION!
●
The actions described in these instructions should only be performed
by authorized, qualified personnel. Equipment repairs should only be
performed by qualified staff. Any failure to observe the guidelines in
this manual, and any unauthorized openings and improper repairs
could expose the user to risks (electric shock, fire hazards) and could
also damage the equipment. Please note that any unauthorized
openings of the device will result in the invalidation of the warranty
and exclusion from all liability.
●
Transport the device only in the antistatic original packaging or in
packaging that protects it from knocks and jolts.
●
Only install expansions that are allowed for the system board. If you
install other expansions, you may damage the requirements and rules
governing safety and electromagnetic compatibility or your system.
Information on which system expansions are suitable can be
obtained from the customer service centre or your sales outlet.
●
The warranty expires if the device is damaged during the installation
or replacement of system expansions.
D2550 (TX120)
Technical Manual
7
Notes on safety
V
Important notes
●
Components can become very hot during operation. Ensure you do
not touch components when making extensions to the system board.
There is a danger of burns!
●
Transmission lines to peripheral devices must be adequately
shielded.
●
To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●
Never connect or disconnect data transmission lines during a storm
(lightning hazard).
Batteries
V CAUTION!
●
Incorrect replacement of lithium battery may lead to a risk of
explosion. The batteries may only be replaced with identical batteries
or with a type recommended by the manufacturer.
It is essential to observe the instructions in chapter “Replacing the
lithium battery”.
8
Technical Manual
D2550 (TX120)
Important notes
Notes on safety
Modules with electrostatic-sensitive components
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●
You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●
The equipment and tools you use must be free of static charges.
●
Remove the power plug from the power socket before inserting or removing
boards containing ESDs.
●
Always hold boards with ESDs by their edges.
●
Never touch pins or conductors on boards fitted with ESDs.
●
Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install/deinstall the board.
●
Place all components on a static-safe base.
I You will find a detailed description for handling ESD components in the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).
D2550 (TX120)
Technical Manual
9
CE Certificate
Important notes
Notes about boards
●
During installation/deinstallation of the system board, observe the specific
instructions described in the service supplement for the respective device.
●
Remove the plug from the mains outlet so that system and system board are
totally disconnected from the mains voltage.
●
To prevent damage to the system board, the components and conductors on
it, please take great care when you insert or remove boards. Take great care
to ensure that extension boards are slotted in straight, without damaging
components or conductors on the system board, or any other components,
for example EMI spring contacts
●
Be careful with the locking mechanisms (catches, centring pins etc.) when
you replace the system board or components on it, for example memory
modules or processors.
●
Never use sharp objects (screwdrivers) for leverage.
2.2
CE Certificate
The system complies with the requirements of the EC directives
2004/108/EC regarding “Electromagnetic Compatibility” and
2006/95/EC "Low Voltage Directive”. This is indicated by the CE
marking (CE = Communauté Européenne).
10
Technical Manual
D2550 (TX120)
Important notes
2.3
Environmental Protection
Environmental Protection
Environmentally friendly product design and development
This product has been designed in accordance with standards for ”environmentally friendly product design and development“. This means that the designers
have taken into account important criteria such as durability, selection of
materials and coding, emissions, packaging, the ease with which the product
can be dismantled and the extent to which it can be recycled.
This saves resources and thus reduces the harm done to the environment.
Notes on saving energy
Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work.
Notes on packaging
Please do not throw away the packaging. We recommend that you do not throw
away the original packaging in case you need it later for transporting.
Notes on dealing with consumables
Please dispose batteries in accordance with local government regulations.
Do not throw batteries and accumulators into the household waste. They must
be disposed of in accordance with local regulations concerning special waste.
All batteries containing pollutants are marked with a symbol (a crossed-out
rubbish bin on wheels). In addition, the marking is provided with the chemical
symbol of the heavy metal decisive for the classification as a pollutant:
Cd Cadmium
Hg Mercury
Pb Lead
Notes on labeling plastic housing parts
Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.
D2550 (TX120)
Technical Manual
11
Environmental Protection
Important notes
Returning, recycling and disposal
The device may not be disposed of with household rubbish. This
appliance is labelled in accordance with European Directive
2002/96/EC concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and
recycling of used appliances as applicable throughout the EU.
To return your used device, please use the return and collection
systems available to you. You will find further information on this
at www.fujitsu-siemens.com/recycling.
For details on returning and reuse of devices and consumables within Europe,
refer to the “Returning used devices” manual, or contact your Fujitsu Siemens
Computers branch office/subsidiary or our recycling centre in Paderborn:
Fujitsu Siemens Computers
Recycling Center
D-33106 Paderborn
Tel.
+49 5251 8 18010
Fax
+49 5251 8 18015
12
Technical Manual
D2550 (TX120)
3
Features
3.1
Overview
Processors
– Dual-Core Intel® XEON® processor 3070 (2,66 GHz) or 3040 (1,86 GHz)
Main Memory
– 4 slots for main memory DDR2 533/667 MHz (unbuffered),
SDRAM memory modules with 512 MB up to 2 Gbyte
– maximum 8 Gbyte of memory
– minimum 512 MB
– ECC multiple bit error detection and single bit error correction
Chips on the system board
Intel® 3000 MCH chipset (north bridge)
Intel® ICH7R chipset (south bridge)
Intel® PXH-V (PCI bridge)
SMSC 5027 (super I/O chipset))
LSI1064E 4-port SAS controller (with integrated RAID support)
GBit LAN controller (Broadcom BCM5754)
Broadcom BCM5241 10/100 BASE-TX single-channel transceiver
(for service LAN)
– iRMC chipset with integrated graphic controller
–
–
–
–
–
–
–
D2550 (TX120)
Technical Manual
13
Overview
Features
internal connectors
– USB 2.0 (for an optional backup drive)
– floppy disk drive
– IDEr
– SAS
– SATA
– 2 SAS-LED/HDD-LE
– CPU fan
– 2 system fan
– 12V (CPU) power
– front panel
– intrusion detection (currently not used)
external connectors
– 1 serial port (COM1)
– 2 PS/2 interfaces for keyboard and mouse
– 4 USB 2.0 ports (2 at the front, 2 at the rear)
– 1 VGA port
– 1 RJ45 LAN port
– 1 RJ45 Service LAN port
Slots for expansion boards (low profile)
– 1 x PCI (32 Bit / 33 MHz)
– 1 x PCI Express x4 (x8 connector)
– 1 x PCI Express x1 (short)
BIOS features
– Phoenix System BIOS V 4.06
Environmental protection
Battery in holder
Form factor, slot compatibility list
– 210 mm x 335 mm
14
Technical Manual
D2550 (TX120)
Features
3.2
Main memory
Main memory
The system board supports up to 8 Gbyte main memory. 4 slots (2 memory
banks with 2 modules) are available for the main memory. Each memory bank
can be populated with 512 Mbyte, 1 Gbyte or 1 Gbyte unbuffered DDR2
memory modules.
Module population
㸣system board
2B
1B
2A
1A
front
rear
Figure 2: Position and structure of the main memory
D2550 (TX120)
Technical Manual
15
Main memory
Features
– If the memory modules are populated in pairs, each pair must consist of
identical memory modules (2-way interleaved mode).
– The module capacity between pairs can differ: pair 2A/2B can be populated
with two 512 Mbyte memory modules and pair 1A/1B with two 1 Gbyte
memory modules.
Following table shows the mandatory population order:
Modes
DIMM-1A
DIMM-2A
DIMM-1B
DIMM-2B
single channel
populated
empty
empty
empty
single / dual
channel1
populated
populated
populated
empty
populated
empty
populated
empty
dual channel
populated
populated
populated
populated
1The
dual channel mode is only activated, if the memory size installed in the DIMM-2A slot is
equal to the sum of the memory modules installed in the DIMM-1A and DIMM-1B slots.
(e. g.: DIMM-1A=512Mbyte, DIMM-1B=512Mbyte, DIMM-2A=1Gbyte)
16
Technical Manual
D2550 (TX120)
Features
3.3
PCI bus
PCI bus
Front
Rear
slot 3: PCI-E x1
slot 2: PCI-E x4
slot 1: PCI (32bit/33MHz )
Figure 3: PCI slots
PCI slots
The following table shows an overview of the PCI slots:
PCI slot Description
1
32 bit PCI bus slot (32-Bit/33MHz)
2
PCI-Express x4 bus-slot (connector with x8 format)
3
PCI-Express x1 bus slot (connector with x1 format)
D2550 (TX120)
Technical Manual
17
PCI bus
Features
PCI IRQ Line x - Assignment of the PCI interrupts
PCI IRQ Line x defines which ISA interrupts are used for the separate PCI slots.
If you select Auto in the BIOS setup, the interrupts are assigned automatically
and no further settings are required.
Multifunctional PCI boards or boards with an integrated PCI-to-PCI bridge can
use several PCI interrupts (INTA#, INTB#, INTC#, INTD#). Monofunctional PCI
boards (default) only use one PCI interrupt (INTA#) per PCI slot.
The PCI interrupts INTA#, INTB#, INTC# and INTD# are available for each PCI
slot.
The same interrupt can be assigned simultaneously to several PCI boards. You
should avoid this condition due to reduced performance.
If you use a setting other than Auto, the Plug&Play functionality of the system
BIOS for the corresponding PCI boards is deactivated.
Auto
The PCI interrupts are assigned automatically in accordance with
the Plug&Play guidelines.
Disabled
No ISA interrupt is assigned to the PCI interrupt.
3, 4, 5, 6, 7, 9, 10, 11, 12, 14, 15
The selected ISA interrupt is assigned to the PCI interrupt. You
may not select an ISA interrupt that is used by a component on
the system board (e.g. controller) or an ISA board.
18
Technical Manual
D2550 (TX120)
Features
PCI bus
IRQ
Device
IRQ 0
timer output 0
IRQ 1
keyboard
IRQ 4
serial port COM1
IRQ 6
floppy drive controller
IRQ 7
ethernet controller
IRQ 8
real time clock (RTC)
IRQ 9
SCI interrupt
IRQ 10
SMB controller
IRQ 12
PS/2 mouse controller
IRQ 13
numeric processor
IRQ 14
embedded hard drive
IRQ 15
embedded hard drive
IRQs 2,3,5, and 11 are available for add-on devices
Mapping expansion slot device ID / IRQ
PCI-X/
PCI
Device
IDSEL
INTA
INTB
INTC
INTD
REQ/
GNT
PCI
PCI
Slot 1
PCI_
AD18
PCI_
IRQ#A
PCI_
IRQ#B
PCI_
IRQ#C
PCI_
IRQ#D
PCI_
IRQ#1
IDSEL: ID Select
REQ/GNT: Request / Grant
D2550 (TX120)
Technical Manual
19
Screen resolution
3.4
Features
Screen resolution
Depending on the operating system used the screen resolutions in the following
table refer to the screen controller on the system board (with Matrox VGA
driver). The Matrox graphic controller is integrated in iRMC (integrated Remote
Management Controller).
Screen resolution Maximal refresh rate (Hz)
Maximal colour depth
640x480
200
32 Bit
800x600
200
32 Bit
1024x768
100
16 Bit
1280x1024
85
8 Bit
If you are using a different screen controller, you will find details of supported
screen resolutions in the documentation supplied with the controller.
3.5
Temperature / system monitoring
Temperature and system monitoring aim to reliably protect the computer
hardware against damage caused by overheating. In addition, any unnecessary
noise is also prevented by reducing the fan speed, and information is provided
about the system status.
The temperature and system monitoring are controlled by an onboard controller.
The following functions are supported:
Temperature monitoring
Measurement of the processor and the inhouse temperature by an onboard
sensor, measurement of the ambient temperature by a I²C temperature sensor.
Fan monitoring
Fans that are no longer available, blocked or sticky fans are detected.
Fan control
The fans are regulated according to temperature.
20
Technical Manual
D2550 (TX120)
Features
Temperature / system monitoring
Sensor monitoring
The removal of, or a fault in, a temperature sensor is detected. Should this
happen all fans monitored by this sensor run at maximum speed, to achieve the
greatest possible protection of the hardware.
Voltage monitoring
When voltage exceeds warning level high or falls below warning level low an
alert will be generated.
Cover monitoring (currently not used)
Unauthorized opening of the cover is detected, even when the system is
switched off. However, this will only be indicated when the system is switched
on again
System Event Log (SEL)
All monitored events of the system board are recorded in the System Event Log.
They could be retrieved after a reboot via ServerView.
D2550 (TX120)
Technical Manual
21
LEDs
3.6
Features
LEDs
2
1
Figure 4: LEDs
The LEDs have the following meaning:
LED
Indicator
1
yellow flashing SAS controller is healthy
2
green flashing
22
Meaning
iRMC is healthy
Technical Manual
D2550 (TX120)
Features
3.7
Connectors and Jumpers
Connectors and Jumpers
Figure 5: Schematic view of the system board D2399
1
system fan 2
12 SAS
2
front panel
13 mouse (top) - keyboard (bottom)
3
intrusion detection
14 COM1 (top) - VGA (bottom)
4
SAS LED cable (upper HDD backplane)
15 service LAN
5
SAS LED cable (lower HDD backplane)
16 GbE-LAN (top) - USB1/2 (bottom)
6
IDE
17 JP3 (see 3.7.1 on page 24)
7
system fan 1
18 buzzer
8
USB for optional backup drive
19 JP2 (see 3.7.1 on page 24)
9
SATA
20 JP1 (see 3.7.1 on page 24)
10 ATX PSU (12 V / 24-Pin)
21 ATX PSU (4-pin)
11 floppy disk drive
22 CPU fan
D2550 (TX120)
Technical Manual
23
Connectors and Jumpers
3.7.1
Features
Settings with jumpers
JP1
JP2
JP3
Example: Changing the standard setting (1-2) to (2-3):
Figure 6: Jumper settings
Number
Function
Setting
Description
JP1
BIOS
recovery
1-2 (standard)
The system is started with the
system BIOS from the system
board
2-3
The system boots from the „Flash
BIOS floppy disk“ (via an external
USB floppy disk drive) and reprograms the system BIOS on the
system board.
1-2
The password query is skipped.
Passwords are deleted.
2-3 (standard)
The password query is effective.
JP2
24
BIOS
password
Technical Manual
D2550 (TX120)
Features
Connectors and Jumpers
Number
Function
Setting
Description
JP3
CMOS
1-2 (standard)
CMOS/RTC settings are not
cleared
2-3
CMOS/RTC settings are cleared
3.7.2
External connectors
1
2
3
5
4
6
7
Figure 7: External ports of the system board D2399
1 LAN port
5 Monitor port (VGA) (blue)
2 2 x USB prots (black)
6 Keyboard port (PS/2) (purple)
3 Service LAN port
7 Mouse port (PS/2) (green)
4 Serial port COM1 (turquoise)
LAN connectors
On this system board you will find a GbE Broadcom LAN controller BCM5754
and a service LAN controller. The GbE Broadcom LAN controller supports the
transfer rates of 10 Mbit/s, 100 Mbit/s and 1 Gbit/s. The LAN controller supports
WOL function through Magic Package™.
It is also possible to boot a device without its own boot hard disk via LAN. Here
PXE is supported.
D2550 (TX120)
Technical Manual
25
Connectors and Jumpers
Features
The LAN controller connectors are equipped with two LEDs (light emitting
diode) indicating the transfer rate and the activity.
2
1
Figure 8: LAN connectors
1
LAN link/activity
LAN transfer rate
standard LAN
2
LAN transfer rate
service LAN
26
off
no LAN connection
lights up green
LAN connection
flashes green
LAN transfer
off
transfer rate 10 Mbit/s
lights up green
transfer rate 100 Mbit/s
lights up yellow
transfer rate 1Gbps
off
transfer rate 10 Mbit/s
lights up green
transfer rate 100 Mbit/s
Technical Manual
D2550 (TX120)
4
Replacing the lithium battery
In order to save the system information permanently, a lithium battery is
installed to provide the CMOS-memory with a current. When the charge is too
low or the battery is empty, a corresponding error message is provided. The
lithium battery must then be replaced.
V ATTENTION!
The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer (CR2032).
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
Make sure that you insert the battery the right way round. The plus pole
must be on the top!
Figure 9: Replacing the lithium battery
Ê Press the locking spring into direction of the arrow (1), so that the lithiumbattery jumps out of its socket.
Ê Remove the battery (2).
Ê Insert a new lithium battery of the same type into the socket (3) and (4).
D2550 (TX120)
Technical Manual
27
Abbreviations
The technical terms and abbreviations given below represent only a selection of
the full list of common technical terms and abbreviations.
Not all technical terms and abbreviations listed here are valid for the described
system board.
ACPI
Advanced Configuration and Power management Interface
ASRR
Automatic Server Recovery and Restart
ATA
Advanced Technology Attachment
BBU
Battery Backup Unit
BIOS
Basic Input Output System
CMOS
Complementary Metal Oxide Semiconductor
COM
COMmunication port
CPU
Central Processing Unit
DDR
Double Data Rate
DIMM
Dual In-line Memory Module
DIP
Dual In-line Package
D2550 (TX120)
Technical Manual
29
Abbreviations
DMI
Desktop Management Interface
DRAM
Dynamic Random Access Memory
ECC
Error Correction Code
EEPROM
Electrical Erasable Programmable Read Only Memory
EPROM
Erasable Programmable Read Only Memory
EMRL
Embedded RAID Logic
EVRD
Enterprise VRD
HPC
Hot-plug Controller
ICE
In Circuit Emulation
IDE
Integrated (intelligent) Drive Electronics
IME
Integrated Mirror Enhanced
IOOP
Intelligent Organization Of PCI
IPMB
Intelligent Platform Management Bus
IPMI
Intelligent Platform Management Interface
30
Technical Manual
D2550 (TX120)
Abbreviations
iRMC
Integrated Remote Management Controller
LAN
Local Area Network
LED
Light Emitting Diode
MPS
Multi Processor Specification
NMI
Non Maskable Interrupt
OEM
Original Equipment Manufacturer
OHCI
Open Host Controller Interface
OS
Operating System
PCI
Peripheral Components Interconnect
PDA
Prefailure Detection and Analyzing
PIO
Programmed Input Output
PLD
Programmable Logic Device
PS(U)
Power Supply (Unit)
PWM
Puls Wide Modulation
D2550 (TX120)
Technical Manual
31
Abbreviations
PXE
Preboot eXecution Environment
RAID
Redundant Array of Independent Disks
RSB
Remote Service Board
RST
ReSeT
RTC
Real Time Clock
SAS
Serial Attached SCSI
SATA
Serial Advanced Technology Attachment
SCSI
Small Computer Systems Interface
SDDC
Single Device Data Correction
SDRAM
Synchronous Dynamic Random Access Memory
SHDG
Server Hardware Design Guide
SMB
System Management Bus
SMM
Server Management Mode
SMP
Symmetrically Multi Processing
32
Technical Manual
D2550 (TX120)
Abbreviations
UHCI
Unified Host Controller Interface
USB
Universal Serial Bus
VGA
Video Graphics Adapter
VRD
Voltage Regulator Down
VRM
Voltage Regulator Module
WfM
Wired for Management
WOL
Wake up On LAN
D2550 (TX120)
Technical Manual
33
Fujitsu Siemens Computers GmbH
User Documentation
81730 München
Germany
Fax: 0 700 / 372 00000
email: manuals@fujitsu-siemens.com
http://manuals.fujitsu-siemens.com
Submitted by
✁
Comments on System Board D2550
for TX120
D2550 (TX120)
Comments
Suggestions
Corrections
Fujitsu Siemens Computers GmbH
User Documentation
81730 München
Germany
Fax: 0 700 / 372 00000
email: manuals@fujitsu-siemens.com
http://manuals.fujitsu-siemens.com
Submitted by
✁
Comments on System Board D2550
for TX120
D2550 (TX120)
Comments
Suggestions
Corrections
Information on this document
On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Computers. This new subsidiary of Fujitsu has been renamed Fujitsu Technology Solutions.
This document from the document archive refers to a product version which
was released a considerable time ago or which is no longer marketed.
Please note that all company references and copyrights in this document have
been legally transferred to Fujitsu Technology Solutions.
Contact and support addresses will now be offered by Fujitsu Technology Solutions and have the format …@ts.fujitsu.com.
The Internet pages of Fujitsu Technology Solutions are available at
http://ts.fujitsu.com/...
and the user documentation at http://manuals.ts.fujitsu.com.
Copyright Fujitsu Technology Solutions, 2009
Hinweise zum vorliegenden Dokument
Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von
Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seitdem den Namen Fujitsu Technology Solutions.
Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine
bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche
Produktversion.
Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden
Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind.
Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions
angeboten und haben die Form …@ts.fujitsu.com.
Die Internetseiten von Fujitsu Technology Solutions finden Sie unter
http://de.ts.fujitsu.com/..., und unter http://manuals.ts.fujitsu.com finden Sie die
Benutzerdokumentation.
Copyright Fujitsu Technology Solutions, 2009
Download PDF
Similar pages
BFS-15W02 カタログ(PDF 242KB)
null 8797379
R17ID7T OFM1
TPPC 150 2550
C
null 10774757