Brief introduction Many thanks for purchasing Gigabit

Brief introduction
Installation
Explanation for LED indicator lamp
Many thanks for purchasing Gigabit Ethernet media
converter!
1. Interface
RJ-45 interface
The transmission media adopts CAT5 twisted-pair with
typical length of 100 meter. It features the function of
automatically identifying the through line and cross
wire.
LED indicator lamps serve as device monitoring and
trouble display. The following is the explanation for
each LED indicator lamp.
This
product
supports
10/100/1000Base-T,
1000Base-X protocol, as well as full duplex and half
duplex mode. This manual is for 10/100/1000M
transceivers. The following purchasing guide is for
customer’s reference.
Purchasing guide for optical transceivers
Model
UTP-MM
Specifications
10/100/1000M adaptive, multi mode 2km,
Fiber interface
All of two fiber interface is SFP fiber module. It is easy
to change fiber module according to custom’s
requirement, such as link length, fiber type etc.
LED
function
status
Describing
PWR
Power LED
ON
Power is
ON.
OFF
Power is
Fail.
ON
Optical
Signal
Detected
OFF
No laser
input.
ON
Fiber link
is ok.
Blink
Acted
OFF
Fiber link
is fail.
3
Blinks
1000M
speed
2
Blinks
100M speed
1
Blinks
10M speed
ON
Link is ok.
Blink
Data is
been
received or
transmitte
d
FX-SD
(RIGHT-DOWN
)
Fiber port
signal
detect LED
SC
UTP-SM
10/100//1000M adaptive, single mode 20km,
SC
UTP-SM
10/100/1000M adaptive, single mode 40km,
SC
UTP-SM
10/100/1000M adaptive, single mode 60km,
2. Connection
The network device (work station, hub or switch) with
RJ-45 interface is connected to RJ-45 jack of Media
Converter through twisted-pair. And the multi/single
mode fiber is connected to SFP fixed in SFP slots.
FX-LINK/ACT
(LEFT-DOWN)
Fiber port
link/action
status LED
SC
UTP-SM
TX-SPEED
(RIGHT-UP)
10/100/1000M adaptive, single mode 80km,
SC
UTP port
speed LED
Packing list
Please check the following items in the package before
installing the transceiver.
Gigabit Ethernet optical transceiver
1set
AC/DC adapter (external)
1pc
Power line (built-in)
1pc
User manual
1copy
Please contact the dealer immediately for any loss or
damage to the above items.
Figure 1
Front Panel of Media Converter
TX-LINK/ACT
(LEFT-UP)
Figure 2
Back Panel of Media Converter
1
UTP port
link/action
status LED
Transmission characteristics of single fiber transceiver
Technical parameters:
Product
Optical
1. Standard Protocol: 10/100/1000Base-T, 1000Base-X protocol
model
wavelength power
(m)
optical
(dBm)
UTP-SM
1310/1550 -3~-8
(20km)
1550/1310
UTP-SM
1310/1550 0~-5
(40km)
1550/1330
UTP-SM
1310/1550 0~-3
(60km)
1550/1330
Receiving
Transmission
sensitivity distance
(dBm)
<-22
2.Connector: Four UTP RJ-45connector, Two SFP SLOTS
(km)
3. Operation mode: full duplex mode or half duplex mode
20
4. Power supply parameter: outside: 5V DC 3A
5. Environmental temperature: 0℃-60 ℃
<-24
40
6. Relative humidity: 5%-90%
8. TP cable: Cat5 UTP cable
<-25
60
9. Transfer fiber:
multi-mode: 50/125, 62.5/125 or 100/140μm
single mode:: 8.3/125, 8.7/125, 9/125 or 10/125μm
Fiber transmission features:
10 .Dimensions:
Gigabit Ethernet Media
Product
Optical
Optical
Sensibility Transmission
40mm x 110mm x 140mm
model
wavelength
power
(dBm)
distance (km)
(nm)
(dBm)
Cautions:
850
-12~-15 <-20
0.55
1. This product is suitable for indoor application.
UTP-SM 20 1310
-3~-8
<-22
20
2. Put on the dust cover of fiber interface when not used.
UTP-SM 40 1310
0~-5
<-24
40
UTP-SM 60 1310
0~-3
<-25
60
UTP-SM 80 1550DFB
0~-1
<-25
80
UTP-MM
Main features
1. Supports 10/100/1000Base-T, 1000Base-X protocol.
2. Flow control for full duplex and half duplex.
3. Supports up to 10k byte JUMBO frame.
4.Suppots Fiber Port Trunking, Increasing Fiber Channel
Bandwidth and Supply Fiber Channel Redundancy.
5. Supports Ports Based VLANS and TAG Based VLANS
(reserved for future releases).
6. In conformity to safety code of FCC and CE MARK.
Converter
(Two Fiber Ports and Four UTP Ports)
3. It is forbidden to stare at the TX fiber-transfer end with naked
eyes.
4. Single optical fiber transceiver must be used in pair (See the
attachment description in delivery).
Trouble shooting:
user manual
(Do not use until you read this manual carefully)
1. Device is not matched. Please select the corresponding
network device according to the transfer rate of the product
(10Mbps or 100Mbps) when connected to other network devices
(network card, hub, switch).
2. Line loss is excessive during the fiber wiring. Excessive loss
in connector plug-in and fiber soldering welding, and excessive
intermediate nodes may cause excessive loss rate or abnormal
operation.
2
Download PDF