SDL-075 PAR灯使用说明书

NEO-STB-0003
Neo-Flash 150 RGB
User Manual
Introduction
Thank you for investing in our Neo-Flash series. The Neo-Flash 150 RGB features 396 high power SMD 5050’s and is a
compact, yet powerful strobe fixture that has been built and designed from the ground up. With correct operation procedures this
fixture will provide many years of service to you. Please read this manual before operating to ensure safety and keep a copy for your
future reference.
Note:
1. Do not use the chemical material around the fixture.
2. The working temperature must be below +40℃,the humidity must be 0~95%.
Indoor use only
Cautions:
1. Please do not link the power when the fixture is in the package;
2. Please do not link the power before the fixture is earth linked.
3. Please do not open the fixture. If you get the problem, please contact the service engineers.
4. Be sure to have the same power input as per the fixture remark.
Special notice: If you want to link more pieces together, the max load is 6pcs.
Packing list:
● NEO-STB-0003 -NEO-FLASH150 RGB LED Strobe light ----------------- 1pc
● User Manual --------------------------------------------------------------------------- 1pc
● Power cable ---------------------------------------------------------------------------- 2pcs
Technical Specifications:
1. Voltage: 90-264VAC 50Hz/60Hz
2. Fuse: 220V 2A/250V or 120V 5A/125V
3. Peak Power:145W
4. Light Source:396x5050 RGB LED
5. Working Mode:DMX、Auto、Sound、Master/Slave
6. DMX Channels:13CHs
7. Dimension:L365xW209xH210mm
8. Weight:5.5 KG
Operation Manual
1、 Panel description:
1. Power Input 2. Power Output 3. MIC 4. DIP SWITCH 5. 3P DMX Input
6. 5P DMX Input 7. 3P DMX Output 8. 5P DMX Output 9、FUSE 10. SAFETY CABLE
2、Dip-switch setting
As per the above photo, switch 1 is “ON”, and the rest are at “OFF”. Set switch 1”~“ switch 10” as “#1”~“#10”, When the switch is
“ON” , we read it as “1”, when the switch is“OFF”, we read it as “0”. When the“ON” or “OFF” are no use, we read it as “X” (When you
switch the switch which is read it as X, there is no function.). If there is no remark, you can also read it as“0”。
3、Function description
Dip switch
#1 #2 #3 #4 #5 #6 #7 #8 #9 #10
Function
DMX Address #1~9 to set up
DMX Mode
0
the DMX address
Auto Mode
X
X
X
X
X
X
X
0
0
1
Sound Mode
X
X
X
X
X
X
X
0
1
1
#10、#9 and #8 is setting the DMX, Auto and Sound function
1. Auto Mode:
Speed Chart:
Speed
1
2
3
4
5
6
7
8
9
10
0
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
0
0
1
Speed 1 (Fastest)
Speed 2
1
Speed 3
Speed 4
1
Speed 5
Speed 6
1
1
Speed 7
1
1
1
Speed 8 (Slowest)
At the Auto mode, 1,2,3 is to select the strobe speed.
Time chart:
8
9
10
0
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
0
1
1
1
Time (longest delay)
At the Auto mode, 4,5,6 is to select the delay of each strobe.
1
0
0
1
Light up time(on time)
1
2
3
4
5
6
7
Time (Shortest delay)
1
Time
Time
1
Time
Time
1
Time
Time
2. Sound Mode:
8
9
10
0
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
1
1
0
Time (longest delay)
At the Sound mode, 4,5,6 is to select the delay of each strobe as per the sound signal.
1
1
Light up time(on time)
1
2
3
4
5
6
Time (Shortest delay)
Time
1
Time
Time
1
Time
Time
Time
1
1
7
3. DMX Mode:
DMX
Channels
Functions
DMX Value
CH1
Strobe brightness
0~255
CH2
Strobe brightness
0~255
Description
st
LED panel 0% ~100%.
nd
LED panel 0%~100%.
rd
LED panel 0%~100%.
Adjust red brightness of the 1
Adjust red brightness of the 2
CH3
Strobe brightness
0~255
Adjust red brightness of the 3
CH4
Strobe brightness
0~255
Adjust green brightness of the 1 LED panel 0%~100%.
CH5
Strobe brightness
0~255
Adjust green brightness of the 2 LED panel 0%~100%.
CH6
Strobe brightness
0~255
Adjust green brightness of the 3 LED panel 0%~100%.
CH7
Strobe brightness
0~255
Adjust blue brightness of the 1
CH8
Strobe brightness
0~255
Adjust blue brightness of the 2
st
nd
rd
st
LED panel 0%~100%.
nd
LED panel 0%~100%.
rd
LED panel 0%~100%.
CH9
Strobe brightness
0~255
Adjust blue brightness of the 3
CH10
Strobe speed
0~255
Adjust the strobe speed: 0%~100%.
CH11
Strobe delay time
0~255
Adjust the strobe delay time 0%~100%.
CH12
CH13
Program
Speed
0~7
CH1~CH11 control effect
8~39
Program 1
40~79
Program 2
80~119
Program 3
120~159
Program 4
160~199
Program 5
200~255
Program 6
0
1~255
Stop
Speed up
1). To link the DMX controller and the strobe light with 3-pin XLR cable.
2). At Master/Slave mode, set up 1pc PAR at AUTO or Sound,the others set up at DMX, the fixture will work at Master/Slave mode.
3). At DMX mode, Note: ① dipswitch #1~9 is address code (set up the address at 1~512; ② dipswitch #1~9 is to say all the address
are at off, the address is 0,Even it is at DMX mode, no DMX signal reception.
4). DMX Address setting as below:
Switch #9 =0;Switch #8 = 0;Switch #7 = 0;Switch #6 = 0; Switch #5 =0;Switch #4 = 0;Switch #4 = 0;Switch #2 = 2; Switch
#1 = 0;值为 0+0+0+0+0+0+4+2+0 = 6, Address is at the value + 1, and the address is 7.
4、 DMX Linking description
DMX controller
Input/output 3pin connector spec:Pin1 = Gnd
Pin2 = Dmx-
Pin3 = Dmx+
Installation setting
Hanging installation
This fixture can be use in the flat surface or hanging in the ceiling or truss with the special clamp.
When you hang it, please fix the bracket hole of the fixture with the special clamp. And then use the safety cable to tie up the
fixture in the truss of ceiling. Note: the safety cable must be available for 10 times weight of the fixture,
Trouble shooting
Problems
Checking list
Trouble shooting
DMX not responding
If the dipswitch set up correctly.
No power for the unit
Check powercon connect correctly
Insert the powercon and twist It approx 10 degree. It
should be “Click” into the position.
Check the DMX connection
Ensure your DMX network is terminated at the end of
the chain with an XLR termination plug.
Check if connection is incorrect.
Inspect and maintain or replace the signal cable,
make sure of the correct connection. And the 1st unit
input is connected with DMX controller output
Check DMX address is incorrect.
Set up the DMX address correctly
Check if the DMX connector in
1unit is getting trouble
Connect the unit input with the other unit output one
by one. If you cannot find the problem this way, please
contact the local service engineer people.
Strobe turns on/off
without control when in
DMX.
Ensure the dipswitch settings are correct, number 10
should be set to the “off” position.
Cleaning and maintenance
We recommend periodic maintenance to make ensure your fixture remains as good as the day you purchased it.
Ensure ventilation points are free of blockages, such as dust, balloons and small children.
Check if the connection is getting loosen or correct regularly to get the safety using.
Check this every month to prevent unit from the overheating. This is crucial to maintain long life on your SMD array.
Clean external housing once a month with a damp cloth, a small amount of household detergent can be used to remove buildup
of oils such as glycol from fog machines.
Clean toughened glass with a non scratch cloth and suitable glass cleaner, do not use a hammer.
Do not use solvents or acid/alkaline solutions to clean, doing so will damage the fixture.
Download PDF