microphone console

PZ-39
MICROPHONE
CONSOLE
Desk top microphone console
with gooseneck for paging,
with push button.
UDE
Main Avda. BARCELONA, 24
Office 08970 - SANT JOAN DESPÍ
BARCELONA - ESPAÑA
Tel: 34-93 477 28 54
Fax: 34-93 261 17 52
ude@udeaudio.com
Madrid C/ LUIS I, 88, 3ª planta
Delegation 28031 - MADRID
ESPAÑA
Tel: 34-91 311 60 76
Fax: 34-91 450 19 97
centro@udeaudio.com
UDE reserves the right to modify the technical characteristics of its products without previous notice
610.145A
1 4
PZ-39
INSTALLATION
PZ-39 microphone console is delivered from factory with following configuration:
Phantom power supply and remote control connection N. It may be connected directly to an
amplifier / mixer UDE, on one input with configuration “microphone with phantom power supply”.
In necessary case, you may configure the console as follow:
1.- Remove back cover of the microphone console (see figure 3)
2.- Phantom power supply:
PZ-39 microphone console is operating with phantom power supply from 12 to 24V DC.
For phantom power supply between 24 to 48V DC, cut resistances R4 and R6 (2 K7) on circuit
board 107.287 (see figure 1)
3.- Connect audio cable to the amplifier or preamplifier, see note 2.
Remote control, normally in position N (see note 1)
4.- Refit the back cover (see figure 3).
NOTE 1: If it is necessary to connect the microphone console far from the amplifier, it is
indispensable to use GZ-924 cable or equivalent.
For distances more than 100m, you have to select jumper JP1 on position D (see figure 1) and
connect according with schematic (see figure 2).
NOTE 2 : The microphone console is delivered from factory with a 3 meters long cord and DIN
connector.
One terminal block built-in is available allowing to disconnect the 3 m cord and to connect the audio
cable with remote control according to the installation requirements (see figure 2).
MICROPHONE CONFIGURATION
Figure 1
PHANTON POWER SUPPLY BETWEEN 24 to 48 VDC
Cut resistances
R4 and R6 (2K7)
JP1
N
-1
2
REMOTE CONTROL N
Distance less than 100 m.
D
REMOTE CONTROL D
Distance more than 100 m.
+3
R4
R6
TM4
RTM
5
D N
610.145A
2 4
PZ-39
Figure 2
CONNECTION (JP1 on position D)
AMPLIFIER
PREAMPLIFIER
Distance=
100 m.
PZ-39
-1
DIN
CONNECTOR
2
1
3
5 2 4
+3
TM4
RTM
5
4
8 cm.
aprox.
2
1
Figure 3
3
OPENING AND CLOSING
BACK COVER
610.145A
3 4
PZ-39
PZ-39
1
2
1 Microphone cell
2 Microphone gooseneck
3 Push button "SPEECH"
4 Lamp "SPEECH"
UDE
4
3
DIN
CONNECTOR
Gooseneck length: 300 mm.
SIGNAL
1
3
5 2 4
REMOTE
CONTROL
TECHNICAL CHARACTERISTICS
58
108
152
DIMENSIONS IN MILLIMETRES
- Unidirectional electret microphone.
- Signal output:
Balanced.
- Impedance:
600 .
- Power supply:
Phantom.
- Sensibility: -67 dB (0 dB = 1 V / µBar).
150 Hz to 10 kHz.
- Frequency range:
ABS / Metal.
- Material:
- Colour:
Anthracite grey.
- Connection:
DIN connector.
- Cable length:
3 metres.
400 grammes.
- Weight:
610.145A
4 4
Download PDF