AII 24307-26524 Security System.pmd

Accessory
INSTALLATION
INSTRUCTIONS
Publications No.
AII 24307-26524
2003 ELEMENT
SECURITY SYSTEM
Issue Date
JAN 2004
NOTE: An optional keyless entry system (sold
seperately) must be installed before you can install the
security system.
PARTS LIST
Application
Security System Attachment (sold separately)
P/N 08E55-SCV-100
Security system harness
Security System (sold separately)
P/N 08E51-EP4-100
Security unit
8 Wire ties
2 Cushion tapes
LED
Wire tie with connector holder
Push nut
2-pin connector (for LED)
Microphone
Window decal
Owner’s Manual
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Holder bracket
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Felt-tip pen
Tape measure
Eye protection (safety goggles, face shield, etc.)
Drill
3 mm, 5.5 mm, and 8 mm Bits
Isopropyl alcohol
Shop towel
Center punch
File
Diagonal cutters
Ratchet
10 mm Socket
Electrical tape
AII 24307-26524 (0401)
08E55-SCV-1000-91
1 of 8
Illustration of the Security System Installed on the
Vehicle
4.
LED
SECURITY
UNIT
2715090K
SECURITY SYSTEM
HARNESS
Lower the steering wheel using the tilt lever.
Remove the two self-tapping screws and one
washer-screw from the lower steering column
cover. Separate the upper steering column cover
from the lower steering column cover by gently
pressing down on the six retaining tabs, and
release them.
NOTE: To remove the upper steering column
cover from the lower steering column cover, turn
the steering wheel 90° clockwise, then press down
on the area shown to release the retaining tab
indicated so that the remaining tabs can easily be
released.
MICROPHONE
STEERING WHEEL
(Turn the steering wheel 90°
clockwise.)
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1.
Press.
If equipped, make sure you have the anti-theft
code for the radio, then write down the radio
station presets.
UPPER STEERING
COLUMN COVER
2.
Disconnect the negative cable from the battery.
3.
Remove the driver’s dashboard lower cover, turn
the knobs clockwise, then pull the lower cover out
toward you to release the six retaining tabs.
TILT LEVER
LOWER
STEERING
COLUMN
COVER
RETAINING
TABS (6)
WASHER
SCREW
DRIVER’S
DASHBOARD
LOWER
COVER
KNOB
2 of 8
RETAINING
TABS (6)
SELF
TAPPING
SCREW
2422011K
2403050K
AII 24307-26524 (0401)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
5.
Remove the center dashboard lower cover (two
expansion clips, two clips and four retaining tabs).
7.
NOTE: This illustration shows the center lower
cover with subwoofer. Remove the center lower
cover without subwoofer the same way.
On A/T model: Using a hammer handle, push up
on the shift lever cover to release the four
retaining tabs and four clips. Unplug the hazard
switch harness connector and remove the shift
lever cover.
RETAINING
TABS (4)
HAMMER
CLIPS (4)
RETAINING
TAB
EXPANSION
CLIPS (2)
CLIPS (2)
CENTER
DASHBOARD
LOWER COVER
2403062K
SHIFT LEVER
COVER
6.
If the vehicle is equipped with a subwoofer,
remove the bolts that fastens the subwoofer,
unplug the connectors and remove the subwoofer.
RETAINING
RETAINING
TAB
TAB
HAZARD SWITCH
HARNESS CONNECTOR
2712061K
VEHICLE
CONNECTOR
BOLT
BOLT
SUB WOOFER
(if equipped)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
2712050K
AII 24307-26524 (0401)
3 of 8
8.
On M/T model: Slide the top of the shift boot down
away from the shift knob, then remove the shift
knob by turning it counter-clockwise.
Slide top
down.
SHIFT
BOOT
SHIFT
KNOB
12. Route the terminal ends of the LED through the
hole and secure the LED with the push nut. Using
isopropyl alcohol, clean the area where the
cushion tape will attach. Secure the LED harness
to the back of the upper column cover with one
cushion tape.
CLIPS (4)
LED
UPPER STEERING
COLUMN COVER
RETAINING
TAB
RETAINING
TAB
HAZARD SWITCH
HARNESS
CONNECTOR
9.
RETAINING
TAB
SHIFT LEVER
COVER
CUSHION
TAPE
2712071K
PUSH
NUT
On M/T model: Reach through the shift boot, pull
up the shift lever cover to release the four
retaining tabs and four clips and unplug the hazard
switch harness connector.
2712090K
10. Measure and mark the upper steering column
cover in the area shown.
PUNCH
13. Locate the 2-pin connector from the kit. Firmly
push the LED terminals into the 2-pin connector
and lower the lock as shown.
DRILL
NOTE: If the wires are not correctly installed in
the connector, the LED will not work.
5.5 mm bit
LOCK
FELT-TIP PEN
WHITE WIRE
2-PIN
CONNECTOR
UPPER STEERING
COLUMN COVER
2712080K
2712100K
RED WIRE
60 mm
11. While wearing eye protection, lightly center-punch
the mark and drill a 5.5 mm hole through the upper
steering column cover. Remove all burrs.
4 of 8
AII 24307-26524 (0401)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
14. Measure and mark the shift lever cover as shown.
CLIP
A/T Model:
16. Measure and mark the microphone cable in the
area shown. Attach a piece of electrical tape to
the microphone cable at the marked location.
Mark with a piece of
electrical tape.
FELT-TIP PEN
DRILL
MICROPHONE
13 mm
9 mm
A/T model: 180 mm
M/T model: 250 mm
2715010K
8 mm bit
17. Route the microphone jack down through the hole
in the shift lever cover and seat the microphone.
2712110K
SHIFT LEVER
COVER
M/T Model:
SHIFT LEVER
COVER
FELT-TIP PEN
CLIP
DRILL
14 mm
8 mm bit
MICROPHONE
SHIFT
LEVER
COVER
MICROPHONE
JACK
2712120K
2715020K
18. Reconnect the Hazard Switch Harness connector
and reinstall the shift lever cover.
15. While wearing eye protection, lightly center-punch
the mark and drill an 8 mm hole through the
center-punched mark. Remove all burrs. Drill a
pilot hole with a 3 mm bit, then finish with an 8
mm bit.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 24307-26524 (0401)
5 of 8
19. Locate the 22-pin connector blue-taped to the
vehicle harness and remove the blue tape to free
the 22-pin connector. Remove the retainer from the
22-pin connector.
RETAINER
23. Slide the security unit into place on the keyless
entry receiver bracket holder. Do not push the
connector area.
KEYLESS ENTRY
RECEIVER BRACKET
TERMINAL CONNECTOR LOCATION
SECURITY
UNIT
VEHICLE 22-PIN
CONNECTOR
Wire Side View
SECURITY
SYSTEM
HARNESS
TERMINAL
2011010K
CONNECTOR AREA
(Do not push here.)
VEHICLE
22-PIN
CONNECTOR
BLUE
TAPE
2715032K
20. Push the security system harness terminal into
the appropriate vehicle 22-pin connector terminal,
then reinstall the retainer.
24. Plug the vehicle 22-pin connector into the security
unit. Reinstall the receiver bracket.
21. Unplug the vehicle 5-pin connector from the
keyless unit. Remove the receiver bracket (one
bolt).
BOLT
BOLT
(Reuse.)
RECEIVER
BRACKET
RECEIVER
BRACKET
KEYLESS
UNIT
SECURITY
UNIT
BOLT
(Reuse.)
VEHICLE
5-PIN
CONNECTOR
SECURITY SYSTEM
HARNESS TERMINAL
2007121K
VEHICLE 22-PIN
CONNECTOR
SECURITY SYSTEM
HARNESS
22. Remove the bolt that secures the vehicle ground
terminal and attach the security system harness
ground terminal with this bolt.
6 of 8
2715042K
VEHICLE 5-PIN
CONNECTOR
25. Reconnect the vehicle 5-pin connector to the
keyless unit.
AII 24307-26524 (0401)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
26. Reinstall the upper steering column cover, then
route the LED harness along the vehicle harness.
UPPER STEERING
COLUMN COVER
28. Slide the holder bracket onto the LED harness
2-pin connector and then onto the the wire tie with
the connector holder. Secure the LED harness
2-pin connector to the vehicle harness.
Loop and
secure the
excess LED
harness.
LED
HARNESS
LED
HARNESS
WIRE TIE
2-PIN
CONNECTOR
WIRE TIE
WITH
CONNECTOR
HOLDER
VEHICLE
HARNESS
VEHICLE
HARNESS
VEHICLE
WIRE TIE
STEERING
SHAFT
SECURITY
SYSTEM
HARNESS
WIRE TIE
WITH
CONNECTOR
HOLDER
2715050K
LED HARNESS 2-PIN
CONNECTOR
27. Route the security system harness 2-pin
connector under the steering shaft and connect it
to the LED harness 2-pin connector.
HOLDER
BRACKET
2715061K
29. Secure the LED harness to the vehicle harness
with one additional wire tie.
30. Reinstall the lower steering column cover to the
upper steering column cover.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 24307-26524 (0401)
7 of 8
31. Route the microphone jack along the vehicle
harness and the security harness, and plug it into
the security unit.
35. Check that all wire harnesses and cables are
routed properly and that all connectors are
plugged in.
36. Reinstall all removed parts.
SECURITY UNIT
MICROPHONE
INSTRUMENT
PANEL FRAME
37. Reconnect the negative cable to the battery.
38. Enter the customer’s radio anti-theft code and
reset the radio station presets.
39. Reset the clock.
40. Check operation of the security system according
to the Security System owner’s manual.
MICROPHONE
JACK
Clean
here.
CUSHION
TAPE
2715070K
32. Using isopropyl alcohol, thoroughly clean the
instrument panel frame where the cushion tape will
attach. Attach the cushion tape to the instrument
panel frame.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
41. Start the engine. Push down on the driver’s
window switch until the window is fully open.
42. Pull up on the driver’s window switch to close
the window completely, then hold the switch for
2 seconds.
43. Lower and raise the window to check operation of
the driver’s window AUTO function.
33. Secure the microphone harness to the instrument
panel frame with one wire tie at the point where
the electrical tape was attached in step 16.
SECURITY
HARNESS
ELECTRICAL TAPE
(Attached in step 16.)
MICROPHONE
HARNESS
INSTRUMENT
PANEL FRAME
WIRE TIE
INSTRUMENT
PANEL FRAME
WIRE TIE
WIRE TIE
(Loop the microphone
harness and secure it
with a wire tie.)
MICROPHONE
HARNESS
WIRE TIE
2715080K
34. Attach the security harness and microphone
harness to the vehicle harness with five wire ties
in the areas shown.
NOTE: Loop the excess microphone harness and
secure it with one wire tie as shown.
8 of 8
AII 24307-26524 (0401)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Download PDF