The first electromechanical crimping tool with

www.klauke.com
Technical data
Article
Crimping force
15 kN (max.)
Electromechanical crimping tool 0.14 - 50 mm²
Crimping range
0.14 - 50 mm²
Scope of supply
Crimping time
< 1.5 sec. (depending on connecting material)
Battery 10.8 V / 1.5 Ah, Li-Ion (16.2 Wh)
RAML1
Number of crimps
per battery charge
approx. 300 at 10 mm² Cu DIN 46234
Charger for 10.8 V Li-Ion batteries, 230 V
LGML1
Battery voltage
10.8 V
Crimping die for insulated connectors 0.5 - 6 mm²
IS5071
Battery capacity
1.5 Ah, Li-Ion
Charging time
approx. 40 min.
Weight incl. battery
0.96 kg
Environmental temperature
-10 °C up to +40 °C
Accessories
USB adapter
PGA1
Variants
Electromechanical crimping tool 0.14 - 50 mm²
with RAM L1 battery, excl. charger, crimping die, plastic case
Crimping range
Tubular cable lugs and connectors – Cu, standard design
0.75 - 10 mm²
Solderless terminals (DIN 46234) and pin terminals (DIN 46230),
solderless connectors (DIN 46341)
0.5 - 10 mm²
Cable end-sleeves
0.14 - 50 mm²
Insulated cable connections
0.1 - 16 mm²
Non-insulated receptacles
0.25 - 6 mm²
You will find more available dies in our catalogue or at www.klauke.com
Strong brands for your success:
Phone
Fax
Email
Website
+49 2191/ 907- 0
+49 2191/ 907-141
info@klauke.textron.com
www.klauke.com
EK50ML-L
Crimping profile
© 2014 Gustav Klauke GmbH, All rights reserved. Subject to technical changes without notice. BRMICROGB 3.000 03/14 I
Connecting material
Suitable for
Gustav Klauke GmbH
Auf dem Knapp 46
42855 Remscheid
Germany
TECHN
EK50ML
The first electromechanical crimping tool
with PowerSense technology
OLOGY
Times change.
www.klauke.com
Technical data
Article
Crimping force
15 kN (max.)
Electromechanical crimping tool 0.14 - 50 mm²
Crimping range
0.14 - 50 mm²
Scope of supply
Crimping time
< 1.5 sec. (depending on connecting material)
Battery 10.8 V / 1.5 Ah, Li-Ion (16.2 Wh)
RAML1
Number of crimps
per battery charge
approx. 300 at 10 mm² Cu DIN 46234
Charger for 10.8 V Li-Ion batteries, 230 V
LGML1
Battery voltage
10.8 V
Crimping die for insulated connectors 0.5 - 6 mm²
IS5071
Battery capacity
1.5 Ah, Li-Ion
Charging time
approx. 40 min.
Weight incl. battery
0.96 kg
Environmental temperature
-10 °C up to +40 °C
Accessories
USB adapter
PGA1
Variants
Electromechanical crimping tool 0.14 - 50 mm²
with RAM L1 battery, excl. charger, crimping die, plastic case
Crimping range
Tubular cable lugs and connectors – Cu, standard design
0.75 - 10 mm²
Solderless terminals (DIN 46234) and pin terminals (DIN 46230),
solderless connectors (DIN 46341)
0.5 - 10 mm²
Cable end-sleeves
0.14 - 50 mm²
Insulated cable connections
0.1 - 16 mm²
Non-insulated receptacles
0.25 - 6 mm²
You will find more available dies in our catalogue or at www.klauke.com
Strong brands for your success:
Phone
Fax
Email
Website
+49 2191/ 907- 0
+49 2191/ 907-141
info@klauke.textron.com
www.klauke.com
EK50ML-L
Crimping profile
© 2014 Gustav Klauke GmbH, All rights reserved. Subject to technical changes without notice. BRMICROGB 3.000 03/14 I
Connecting material
Suitable for
Gustav Klauke GmbH
Auf dem Knapp 46
42855 Remscheid
Germany
TECHN
EK50ML
The first electromechanical crimping tool
with PowerSense technology
OLOGY
Times change.
ELECTROMECHANICAL CRIMPING TOOL EK 50ML
Whether you want high speed, low weight or efficient drive technology, the Klauke micro
combines the benefits of manual crimping tools with the convenience of battery-powered
hydraulic tools in just one device. Thanks to its compact design it is ideal for jobs where
connecting material has to be crimped quickly and in a high volume on the one hand and
also wherever a handy, mobile tool is required, e.g. for switch cabinet construction and
numerous other installation applications in trade and industry. The Klauke micro is the ideal
solution for those who want both – maximum efficiency and optimum ease of use.
PowerSense
Technology
And so do requirements.
Technologies develop.
Micro compact, maximum efficiency
Very easy handling
thanks to PowerSense technology
Automatic retraction
when operation is complete
Interchangeable Klauke 50-series
crimping dies
for all common applications up to 50 mm²
Electronic control
with blocking function and motor stall protection
High speed
Crimping time < 1.5 sec.
Ergonomic two-component housing
in Klauke “In-line Design”
Very low weight
tool incl. battery < 1 kg
LED light to illuminate
working area
10.8 V lithium-ion battery
with charge level indicator
Long service life
with service intervals of 35,000 cycles
Versatile
for comfortable crimping of cable
connections, cable end-sleeves and
cable lugs
Balanced and drop-proof
thanks to key ring for use with balancer
or for securing in field work
LED light
to illuminate working area
Smart and powerful
with multi-function LED for maintenance
control and data transfer as well as
a powerful lithium-ion battery with
charge level indicator
Fast, light, efficient –
the way you crimp today.
Innovative
The new way of crimping for cross-sections up to
50 mm2: Klauke micro. As fast and easy to use as a
mechanical crimping tool, as powerful and efficient
as a hydraulic tool.
single-lever control
for all tool functions
The unique PowerSense technology – “Manual
pre-clamping, motorized crimping” makes the
crimping process revolutionary simpler and at the
same time more efficient than ever.
THE REVOLUTIONARY POWERSENSE TECHNOLOGY
clamp
1. Manual pre-clamping
2. Motorized crimping
… and done
Operating the lever closes the crimping jaws
without any exertion on the part of the user
and fixes the connecting material. In this
“pre-clamped” state it is still possible to
adjust the position and the alignment.
Further actuation or “pulling back”
the lever starts the crimping process
fully automatically using the power of
the integrated motor.
The retraction to the starting position is also
fully automatic. During the entire crimping
cycle the process can be interrupted by
actuating the lever in the opposite direction.
crimp
ELECTROMECHANICAL CRIMPING TOOL EK 50ML
Whether you want high speed, low weight or efficient drive technology, the Klauke micro
combines the benefits of manual crimping tools with the convenience of battery-powered
hydraulic tools in just one device. Thanks to its compact design it is ideal for jobs where
connecting material has to be crimped quickly and in a high volume on the one hand and
also wherever a handy, mobile tool is required, e.g. for switch cabinet construction and
numerous other installation applications in trade and industry. The Klauke micro is the ideal
solution for those who want both – maximum efficiency and optimum ease of use.
PowerSense
Technology
And so do requirements.
Technologies develop.
Micro compact, maximum efficiency
Very easy handling
thanks to PowerSense technology
Automatic retraction
when operation is complete
Interchangeable Klauke 50-series
crimping dies
for all common applications up to 50 mm²
Electronic control
with blocking function and motor stall protection
High speed
Crimping time < 1.5 sec.
Ergonomic two-component housing
in Klauke “In-line Design”
Very low weight
tool incl. battery < 1 kg
LED light to illuminate
working area
10.8 V lithium-ion battery
with charge level indicator
Long service life
with service intervals of 35,000 cycles
Versatile
for comfortable crimping of cable
connections, cable end-sleeves and
cable lugs
Balanced and drop-proof
thanks to key ring for use with balancer
or for securing in field work
LED light
to illuminate working area
Smart and powerful
with multi-function LED for maintenance
control and data transfer as well as
a powerful lithium-ion battery with
charge level indicator
Fast, light, efficient –
the way you crimp today.
Innovative
The new way of crimping for cross-sections up to
50 mm2: Klauke micro. As fast and easy to use as a
mechanical crimping tool, as powerful and efficient
as a hydraulic tool.
single-lever control
for all tool functions
The unique PowerSense technology – “Manual
pre-clamping, motorized crimping” makes the
crimping process revolutionary simpler and at the
same time more efficient than ever.
THE REVOLUTIONARY POWERSENSE TECHNOLOGY
clamp
1. Manual pre-clamping
2. Motorized crimping
… and done
Operating the lever closes the crimping jaws
without any exertion on the part of the user
and fixes the connecting material. In this
“pre-clamped” state it is still possible to
adjust the position and the alignment.
Further actuation or “pulling back”
the lever starts the crimping process
fully automatically using the power of
the integrated motor.
The retraction to the starting position is also
fully automatic. During the entire crimping
cycle the process can be interrupted by
actuating the lever in the opposite direction.
crimp
ELECTROMECHANICAL CRIMPING TOOL EK 50ML
Whether you want high speed, low weight or efficient drive technology, the Klauke micro
combines the benefits of manual crimping tools with the convenience of battery-powered
hydraulic tools in just one device. Thanks to its compact design it is ideal for jobs where
connecting material has to be crimped quickly and in a high volume on the one hand and
also wherever a handy, mobile tool is required, e.g. for switch cabinet construction and
numerous other installation applications in trade and industry. The Klauke micro is the ideal
solution for those who want both – maximum efficiency and optimum ease of use.
PowerSense
Technology
And so do requirements.
Technologies develop.
Micro compact, maximum efficiency
Very easy handling
thanks to PowerSense technology
Automatic retraction
when operation is complete
Interchangeable Klauke 50-series
crimping dies
for all common applications up to 50 mm²
Electronic control
with blocking function and motor stall protection
High speed
Crimping time < 1.5 sec.
Ergonomic two-component housing
in Klauke “In-line Design”
Very low weight
tool incl. battery < 1 kg
LED light to illuminate
working area
10.8 V lithium-ion battery
with charge level indicator
Long service life
with service intervals of 35,000 cycles
Versatile
for comfortable crimping of cable
connections, cable end-sleeves and
cable lugs
Balanced and drop-proof
thanks to key ring for use with balancer
or for securing in field work
LED light
to illuminate working area
Smart and powerful
with multi-function LED for maintenance
control and data transfer as well as
a powerful lithium-ion battery with
charge level indicator
Fast, light, efficient –
the way you crimp today.
Innovative
The new way of crimping for cross-sections up to
50 mm2: Klauke micro. As fast and easy to use as a
mechanical crimping tool, as powerful and efficient
as a hydraulic tool.
single-lever control
for all tool functions
The unique PowerSense technology – “Manual
pre-clamping, motorized crimping” makes the
crimping process revolutionary simpler and at the
same time more efficient than ever.
THE REVOLUTIONARY POWERSENSE TECHNOLOGY
clamp
1. Manual pre-clamping
2. Motorized crimping
… and done
Operating the lever closes the crimping jaws
without any exertion on the part of the user
and fixes the connecting material. In this
“pre-clamped” state it is still possible to
adjust the position and the alignment.
Further actuation or “pulling back”
the lever starts the crimping process
fully automatically using the power of
the integrated motor.
The retraction to the starting position is also
fully automatic. During the entire crimping
cycle the process can be interrupted by
actuating the lever in the opposite direction.
crimp
www.klauke.com
Technical data
Article
Crimping force
15 kN (max.)
Electromechanical crimping tool 0.14 - 50 mm²
Crimping range
0.14 - 50 mm²
Scope of supply
Crimping time
< 1.5 sec. (depending on connecting material)
Battery 10.8 V / 1.5 Ah, Li-Ion (16.2 Wh)
RAML1
Number of crimps
per battery charge
approx. 300 at 10 mm² Cu DIN 46234
Charger for 10.8 V Li-Ion batteries, 230 V
LGML1
Battery voltage
10.8 V
Crimping die for insulated connectors 0.5 - 6 mm²
IS5071
Battery capacity
1.5 Ah, Li-Ion
Charging time
approx. 40 min.
Weight incl. battery
0.96 kg
Environmental temperature
-10 °C up to +40 °C
Accessories
USB adapter
PGA1
Variants
Electromechanical crimping tool 0.14 - 50 mm²
with RAM L1 battery, excl. charger, crimping die, plastic case
Crimping range
Tubular cable lugs and connectors – Cu, standard design
0.75 - 10 mm²
Solderless terminals (DIN 46234) and pin terminals (DIN 46230),
solderless connectors (DIN 46341)
0.5 - 10 mm²
Cable end-sleeves
0.14 - 50 mm²
Insulated cable connections
0.1 - 16 mm²
Non-insulated receptacles
0.25 - 6 mm²
You will find more available dies in our catalogue or at www.klauke.com
Strong brands for your success:
Phone
Fax
Email
Website
+49 2191/ 907- 0
+49 2191/ 907-141
info@klauke.textron.com
www.klauke.com
EK50ML-L
Crimping profile
© 2014 Gustav Klauke GmbH, All rights reserved. Subject to technical changes without notice. BRMICROGB 3.000 03/14 I
Connecting material
Suitable for
Gustav Klauke GmbH
Auf dem Knapp 46
42855 Remscheid
Germany
TECHN
EK50ML
The first electromechanical crimping tool
with PowerSense technology
OLOGY
Times change.
Crimping dies
Series 50
K 50
EK 15/50
EK 15/50 G
◾ Crimping dies R 50
Suitable for:
◾ Copper tubular cable lugs and connectors, standard design
Copper tubular cable lugs and connectors, standard design
mm²
Part No.
0.75-2.5
R501
Empty
Empty
0.75-2.5
R501
Empty
Empty
4-10
R502
◾ Crimping dies M 50
Suitable for:
◾ Copper tubular cable lugs and compression joints for solid conductors
Copper tubular cable lugs and compression joints for solid conductors
mm²
Part No.
1.5-4
M50154
Empty
Empty
1.5-4
M50154
Empty
Empty
6-10
M50610
◾ Crimping dies Q 50
Suitable for:
Copper solderless terminals (DIN 46234) and pin terminals (DIN 46230)
acc. to DIN - Cu
◾ Copper solderless terminals (DIN 46234) and pin terminals (DIN 46230)
acc. to DIN - Cu
◾ Copper solderless connectors (DIN 46341) acc. to DIN
mm²
Part No.
0.5-10
Q501
Empty
Empty
0.5-10
Q501
Empty
Empty
◾ Crimping dies AE 50
Suitable for:
◾ Cable end sleeves
Cable end sleeves
mm²
Part No.
0.14-6
AE501
Empty
Empty
0.14-6
AE501
Empty
Empty
10-25
AE502
35-50
AE503
◾ Crimping dies IS 50
Suitable for:
◾ Insulated cable connections, double crimping
Insulated cable connections, double crimping
mm²
Part No.
IS501
leer
IS501
leer
0.1-1
390
for part
0.5-6
0.5-6
8201-8,201B
IS503
Crimping dies
Series 50
◾ Crimping dies IS 50
Suitable for:
◾ Insulated cable connections, single crimping
Insulated cable connections, single crimping
mm²
for part
Part No.
10-16
IS502
Empty
10-16
IS502
Empty
0.5-2.5
670 WS
680 WS
IS504
4-6
700 WS
IS505
◾ Crimping dies CR 50
Suitable for:
◾ Non-insulated receptacles
Non-insulated receptacles
mm²
for part
Part No.
Tab width mm
0,25-6
CR501
2,8 / 6,3
0,25-6
CR501
2,8 / 6,3
0,5-2,5
CR502
4,8
0.5-1
38201, 38,201A
CR503
2.8
0.5-2.5
3720, 3735
CR504
6.3
0.5-1.5
3725
CR505
6.3
◾ Crimping dies BNC 50
Suitable for:
◾ For stud and shielded sleeves
◾ BNC plugs for coax cable RG 58, 59, 62 and 71
For stud and shielded sleeves
Part No.
BNC501
Empty
Empty
Empty
BNC501
Empty
Empty
Empty
Empty
Empty
◾ Crimping dies SB 50
Suitable for:
◾ Turned pin receptacles
◾ Pin connectors
Turned pin receptacles
mm²
Part No.
0.1-1
1.5-2.5
4
SB501
391
Download PDF