model lbt series bluetooth ceiling speaker - Ceiling

BLUETOOTH CEILING SPEAKER
MODEL LBT SERIES
THANK YOU FOR
CHOOSING LITHE AUDIO
Innovative design and advanced engineering built in to our LBT series of wireless Bluetooth
ceiling mount speakers. Designed for easy installation and high quality sound, within seconds each
room is setup and ready. This manual describes the installation of LBS series speakers within
conventional stud and sheetrock (Joist and plasterboard) ceilings.
BOX CONTENTS
Please ensure you read the entire instruction manual carefully before you commence any work.
Carefully unpack the speakers from the packaging. Please check to ensure all the parts shown
below are included.
If any parts of the speaker appear damaged, please contact your dealer/reseller immediately or
contact www.LitheAudio.com for contact details.
MODEL LBT1
MODEL LBT2
IMPORTANT SAFETY WARNING
ALSO INCLUDES
SPEAKER GRILLE
Before use please read completely and use in accordance with these safety instructions.
Before commencing any electrical work ensure the supply is switched OFF at the mains. Either
by switching off the consumer unit or by removing the appropriate fuse. This product should
be installed in accordance with the relevant sections of the building regulations code and in
accordance with the latest edition of IEE regulations (BS 7671).
POWER ADAPTOR
PASSIVE CEILING SPEAKER
If the unit is to be used as a replacement for an existing product, remove the existing unit from its
location and disconnect the wiring. Connect the wires as shown in diagram. Ensure terminals are
properly tightened and ensure no bare wires are visible. When fitting the speaker into the ceiling,
ensure no wires are trapped.
LED COVER
READ THE INSTRUCTIONS CAREFULLY BEFORE STARTING THE
INSTALLATION PROCESS AND KEEP THEM SAFE FOR FUTURE
REFERENCE.
•
•
•
•
•
•
•
•
•
•
Failure to follow the instructions in this guide voids all warranties on your speakers.
Warning: Do not use the product in water.
Warning: Do not install speaker directly above any heat sources such as radiators, or other
apparatus that produce heat.
Warning: To reduce the risk of fire or electric shock, do not expose this speaker to rain or
moisture (directly above bath or shower area) in Bathroom Zone 0, Zone 1 and Zone 2.
Protect the power cable from being damaged, do not over stretch cable.
Only use attachments/accessories specified by the manufacturer Lithe Audio.
Turn off the power to the speaker when unused for long periods of time.
A Fire and Acoustic speaker hood must be used in accordance with UK building and IEE
Regulations with a fire rating of up to 90 minutes, is Parts B, L, C and E compliant.
Do not open the back cover to the speaker as this protects the PCB as this will invalidate
the warranty and could cause electric shock.
Ensure speaker location is free from obstructions such as electrical conduit, HVAC ducts or
Water lines.
BLUETOOTH CEILING
SPEAKER
PREPARATION
BLUETOOTH CEILING SPEAKER
SPEAKER CABLE
EQUIPMENT YOU WILL NEED
Listed below is the hardware equipment needed to install the speaker, with the addition of
a ladder to ensure the installation is done safely. A cutting template is included in the box.
PENCIL
PROTECTIVE EYEWEAR
SPEAKER CABLE
1
CUTTING GUIDE
STUD FINDER
SCREWDRIVER
CUTTING SAW
TAPE
MEASURING TAPE
DRILL
WIRE CUTTERS
2
KNOW YOUR SPEAKER
INSTALLATION
The LitheAudio LBT range of Bluetooth ceiling wireless speakers have various inputs:
IMPORTANT: BEFORE COMMENCING ANY ELECTRICAL WORK ENSURE
THE SUPPLY IS SWITCHED OFF AT THE MAINS. IF YOU ARE UNSURE HOW
TO FIT SEEK HELP FROM A PROFESSIONAL ELECTRICIA /AV INSTALLER
SPEAKER OUTPUT - To connect one additional passive (Slave) speaker (Gold Plated)
RCA INPUTS - To connect directly from CD Player, TV Output, DVD Player etc..
POWER INPUT - To connect (as supplied) transformer
All models have an in ceiling
depth of 3.8” (95 mm)
Connection Reset Button
1. Mark out the position of the speaker using a,
tape measure and mark using a pencil with the
template supplied. Check using a stud finder
to make sure no obstruction is present prior
to cutting.
2. Drill a pilot hole and cut the speaker hole
using a cutting saw. Take caution when
cutting to keep fingers away from cutting
blade and wear protective eyewear.
3. Connect the Power lead from the
transformer (supplied) to a 13A mains plug
socket or terminate to a dedicated fused spur.
Ensure the power lead is not overstretched.
4. Insert speaker into the ceiling then using a
screwdriver lock the 4 dog leg fixings to secure
the speaker in place, do not over tighten.
Attach the magnetic grille to the speaker front.
LED indicator
Ball joint tweeter to
fine tune direction
Magnets for Cover (8)
Enviromental equalizer
(+/- 3db)
RCA Input
RCA-(Black) RCA+(Red)
Built in Amplifier
& Bluetooth driver
Power input 24V/2.5A
Speaker output
R+ (Red) R- (Black)
Dog leg easy install fixings (4)
6.5” (165mm) Kevlar/Polyproplene cone
In built over voltage, under voltage, over temperature, and short circuit protection, if there is an electrical fault,
the power supply to the amplifier will cut off automatically and restart when the speaker has stabilised.
3
BLUETOOTH CEILING SPEAKER
PAINTING THE SPEAKER GRILLE
Do not paint the speaker grilles whilst attached to the speaker. Lithe Audio reccomends spray
painting using 5 parts thinning agent to 1 part paint. Spray thinly to ensure speaker cover grille holes
are not blocked as this will effect the sound quality of the speakers.
INSTALLATIONS IN FIRE-RATED CEILINGS
If you plan to mount your speakers in a fire-rated ceiling, you should purchase a fire hood for the
speaker. Visit Litheaudio.com for more information.
4
SETUP AND PAIRING
CONNECTING DEVICES
NOTE: ENSURE THE BLUETOOTH WIRELESS SPEAKER IS CONNECTED TO
THE POWER SUPPLY AND TURNED ON.
If other devices (such as laptops, tablets, phones etc) want to play through the Bluetooth
speakers please follow the steps below:
The Led indicator will flash Blue/red when ready to pair, turn solid Blue whilst the device is
connected to the speaker and flash blue when music is playing
1. FIRST CONNECTION: If device A connects and controls to Bluetooth, Device B
cannot search or control the Bluetooth speaker. Device A MUST no longer be connected,
then Device B can connect and control.
1. Open the setting menu
and select Bluetooth
2. SECOND CONNECTION: If Device A is connected and has control, Device B can’t
connect to Bluetooth until Device A disconnects, enabling Device B to control the
Bluetooth speakers.
2. Turn on Bluetooth
and search devices
3. ADDITIONAL DEVICES: If additional Devices want to connect to Bluetooth speakers,
a maximum of 2 devices can connect at any one time, only the 1st device to connect
controls the speakers. Please ensure devices A or B are disconnected before trying to
connect additional devices C, D, E etc...
NOTE: If your connection to speaker is lost, the device maybe out of range (>10m).
To reconnect simply go to setting menu on the home screen on your device and reconnect to
Litheaudio BT, Bluetooth speaker.
HARD WIRED INPUT- RCA INPUT
3. Click Lithe Audio BT and
insert PIN “1234” and click Pair
4. The Lithe Audio Bluetooth
speaker is now connected to your
device ready to play your Music.
To connect other devices that may not have a Bluetooth
connection (such as CD players, BluRay player etc) to play
through the Bluetooth speakers please follow the steps
below:
RCA CONNECTION: To play music via speaker RCA
connection connect an RCA cable to the speaker and play
through your device. Ensure ALL Bluetooth connections are
turned off to be able to play through the speaker.
ADDITIONAL SPEAKER - OPTIONAL
PLEASE NOTE: LBT1 DOES NOT INCLUDE PASSIVE SPEAKER
The Lithe Audio Master Bluetooth ceiling
speaker is able to connect to an addtional
passive speaker via the speaker output (+/-)
Use wire cutters to strip the ends of the
speaker cable (if required).
5
Image shows Apple iPhone but visuals may change from device to device. Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
6
SPECIFICATIONS
TROUBLESHOOTING
•
•
•
•
•
•
•
•
•
Sound Quality THD+N<0.009%, 65Hz-20kHz
RMS Power: 50W RMS
Impedance: 8 Ohms
Sensitivity (1W/1m): 90dB
Audio Sample Rate: 8Khz
Line In Analog (RCA), auto-detecting
Type: Class D (Digital)
Woofer: 6.5” Kevlar Woven Cone / Polypropylene
Tweeter: 1.2” Titanium Cone
If a problem arrises, please try the troubleshooting frequently asked guide below. If the
problem is not listed please contact LitheAudio Customer Service Support.
•
•
•
•
•
•
Bluetooth System: Bluetooth V4.0
Frequency Range: 2.4GHz - 2.4832GHz (ISM Band)
RF Channels: 79 (USA, Japan & EU)
Wireless Range: Upto 10 metres
ID Device Name: Lithe Audio
Security Passcode: 1234
•
•
•
•
•
•
•
Power Input Supply : 100 - 240V ~ / 2A
Transformer Output Supply : DC24V / 2.5A
Dimensions (W x D) 6.5 x 3.8 in (230 x 95mm)
Weight 3.85 lbs. (1.75kg)
IP rating: IP44 (Model: LBT1/IP or LBT2/IP only)
Operating Temperature 32º to 104º F (0º to 40º C)
Storage Temperature 4º to 158º F (-20º to 70º C)
•
•
•
Standby : 1.3W / 0.02A
Connected : 1.5W / 0.03A
Playing Music: 2.8W - 10.5W / 0.03A - 0.09A**
*
**
Specifications subject to change without notice.
Power Consumption depends on the type of music & volume - Increased Bass & volume
requires more power loading on the amplifier.
LED INDICATOR COVER
To mask the LED indicator, use the LED cover sticker included
CONNECTION RESET BUTTON
Press and hold the ‘Reset Button’ for 2 seconds to clear the connection memory.
All paired devices will be deleted.
7
BLUETOOTH CEILING SPEAKER
Q: Speaker has not been found during setup
A: Please check power cord is correctly connected into speaker and transformer, Check the
blue / red light is flashing. Press reset button for 5 seconds to reboot the speaker.
Before commencing any electrical work ensure the supply is switched OFF at the mains.
Q: Speaker has failed to connect to Bluetooth
A: Please retry setup and pairing process, follow setup steps 1 - 4 to connect device. Please
ensure speaker password is entered correctly. Ensure the device is within 10m range.
Q: Device is connected to Bluetooth speaker but no sound
A: Ensure your device volume is NOT muted, increase the volume
Q: Can the speaker be installed into the bathroom ceiling.
A: Only the IP rated models ‘LBT1/IP’ or ‘LBT2/IP’can be installed in zone 3 only. Ensure you
read the saftey precautions on page 1 before installation. Warning: Do not use the product
in water or directly above the bath or shower area.
For further queries and support questions please visit www.litheaudio.com/support
Email: support@litheaudio.com or Call +44 (0) 1293 922 015
REGULATION INFORMATION
EUROPE
LitheAudio declares that this product herewith complies with the requirements of the EMC
Directive 2004/108/EC, Low Voltage directive 2006/95/EC, Eco-Design Directive 2005/32/
EC, RoHS Directive 2011/65/EU and the R&TTE Directive 1999/5/EC when installed and
used in accordance with the manufacturer’s instructions. A copy of the full Declaration of
Conformance may be obtained at www.litheaudio.com/support/policies.
Lithe Audio Speakers have a standby mode or remove the power cord from the AC mains.
RECYCLING INFORMATION
This symbol on the product or on its packaging indicates that this product shall not be treated
as household waste.
Instead please deliver it to the applicable collection point for the recycling of electrical and
electronic equipment. By recycling this product correctly, you will help conserve natural
resources and prevent potential negative environmental consequences. For more detailed
information about recycling of this product, please contact your local council office, your
household waste disposal service or the shop where you purchased the product(s) from.
8
2 YEAR GUARANTEE
This Ceiling Speaker is of excellent quality and construction. However, if any defects in materials
or workmanship do appear during the guarantee period, we will, at our discretion, either repair or
replace the defective parts, free of charge, subject to the terms and conditions of our Guarantee
shown below.
This Guarantee covers both parts and labour. Carriage is not included.
This Guarantee provides benefits which are additional to, and do not affect, your statutory rights.
This Guarantee does not cover the cost of returning the product to the dealer from whom it was
purchased or to ourselves. This Guarantee applies only to products sold and located in mainland
Great Britain. It does not cover liability in respect of or replacement of plugs, cables or fuses and
also does not cover defects due to:
• Failure to use or maintain product in accordance with Lithe Audio instructions.
• The product being connected to an unsuitable electricity supply.
• Accidental damage to or abuse or misuse of the product.
• Product modification, except by Lithe Audio or approved agent.
• Dismantling of or interference with the product.
Before returning any product under this Guarantee, please check that:
• You have followed the product instructions correctly.
• Your mains electricity supply is functional.
• The defect is not due to a blown fuse.
If you wish to claim under this guarantee you should:
• Send the product, postage or carriage paid, to the dealer from whom it was purchased or to
Lithe Audio direct.
• Ensure that the product is clean and packed carefully (preferably in its original carton).
• Enclose details of your name, address and telephone number and when and where the product
was purchased, together with proof of purchase (e.g. a invoice or till receipt).
• Give exact details of the nature of the defect.
This Guarantee does not cover any other claims whatsoever, including, without limitation, any
liability for incidental, indirect or consequential damage, nor does it cover any claims for conversion
or modification or for the costs of repair carried out by any third party without the prior consent
of Lithe Audio. If replacement parts are fitted to the product this will not extend the period of the
Guarantee. For further advice contact the Lithe Audio customer services.
Lithe Audio products marked with the CE mark comply with the EC Low Voltage
Directive: 73/23/EEC, Electromagnetic Compatibility Directive 89/336/EEC
WWW.LITHEAUDIO.COM
TEL: 01293 922 015 EMAIL: INFO@LITHEAUDIO.COM
LBTIBGBA
Download PDF