HDMI Extender over IP
Operating Instructions
MODEL:HDIPRX
Operating Instructions
Dear Customer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions
carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
FEATURES

Compliant HDCP.

Flexible and scalable HDMI 1080p High Quality Video Broadcasting with Gigabit Ethernet LAN.

Extends 1080p HDMI signals up to 120m over a single UTP Cat5e/6 cable.

Multicasting and broadcasting architecture, adding more displays without adding LAN bandwidth

Support Point-to-Point, Point-to-Many and Many-to-Many network configuration.

Dual power input: 802.3af compliant PoE & DC5V.
loading.

Up to 8 transmitters and more than 200 receivers possible in a single system.

With IR Control function ,it allows you control back the source at the end of destination

Built-in DIP switch to change Group ID and Utility for remotely

Support IGMP v.1 &v.2 address

Support cascading Ethernet Switches up to 3 layers.
NOTICE
Our company reserve the right to make changes in the hardware, packaging and any accompanying
documentation without prior written notice.
Operating Instructions
TABLE OF CONTENTS
Specifications
Package Contents
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
SPECIFICATIONS
Operating
Temperature
Range
Operating
Humidity
-5 to +35℃(+23 to +95℉)
5 to 90%RH (No Condensation)
Range Video Format
Support
DTV/HDTV:480i/576i/480P/576P/720P/1080i/1080
Output Video
P
HDMI,HDCP
Audio Sampling rate
32kHz, 44.1kHz and 48kHz
Transmission Distance
Power consumption
1080P @60Hz120m(Maximum) over single CAT5E/6
/24AWG/Solid
5V/1A DC , 802.3af PoE
Power consumption: Max. 8W
Dimension (L×W×H)
L94xW93.5x24.6mm
IR frequency range
38-56kHz
Net Weight
Receiver:255g,Transmitter:255g
Default IP address:192.168.168.55;MAC
TX&RX
address:00:0b:78:00:60:01
Default IP address:192.168.168.56;MAC
address:00:0b:78:00:60:02
Note1: Specifications are subject to change without notice. Mass and dimensions are
approximate.
Note2:one TX to many RX or many TX connect to many RX, IP and MAC address must be
different.
PACKING CONTENTS
1) Main Unit. Transmitter & Receiver HDMI Extender
2) Power adapter DC 5V 1Ax2PCS
3) IR-TX cable&IR-RX cable
4) Operating Instructions
Operating Instructions
PANEL DESCRIPTIONS
Transmitter Panel
Indicator of power input
DIP switch
Power input port
Status of signal connection
IR-TX port
HDMI input
Reset button
Ethernet port
4 bits DIP Switch:
1~3for 0~7 (group) ID selection (such as 000,001,010 etc,)
4 for unicast or multicast select
Default Tx unicast IP address is 192.168.168.55 and can be configured from
webpage. Tx Group IP address: 239.168.168.1x, where x is the value of bits[2:0]
Operating Instructions
Receiver Panel
Indicator of power input
DIP switch
Power input port
Status of signal connection
IR-RX port
HDMI Output
Reset button
Ethernet port
4 bits DIP Switch:
1~3for 0~7 (group) ID selection (such as 000,001,010 etc,)
4 for unicast or multicast select
Default Rx unicast IP address is 192.168.168.56 and can be configured from
webpage.Rx Group IP address: 239.168.168.1x, where x is the value of bits[2:0]
Operating Instructions
Using both TX or RX can be as simple plug and play. No configuration
needed. If connecting to multiple receivers or transmitters then setting
the dipswitch to see each end will be required.
Simple set up - place a TX and RX at each end
Advanced set up- Using a POE switch you can eliminate the need for
power supplies on the transmitter and receivers.
User should configure the DIP switch within 10 seconds,
firmware should reset the system 20 second after detecting
the first change of DIP switch, and latch the new DIP switch
value after reset.
How to Connect HDMI Over IP One source to one display
1. Connect one HDMI Cable between the HDMI output port of source device and the
HDMI input port of Transmitter unit
2. Connect one HDMI Cable between the HDMI input port of display and the HDMI
output port of Receiver unit.
3. Connect one UTP Cat5e or better cables between the RJ45 port of Transmitter
unit and RJ45 port of Receiver unit.
4. Connect the included 5V DC power supplies to both Transmitter unit and Receiver
unit.
5. Power on the output device first and the source second.
1) One to One
Transm itter
Receiver
Operating Instructions
How to Connect HDMI Over IP One source to multiple displays
1. Connect one HDMI Cable between the HDMI output port of source device and the
HDMI input port of Transmitter unit
2. Connect one CAT5e or better cable between the RJ45 port of transmitter and
input port of Gigabit Ethernet switch hub.
3. Connect one CAT5e or better cable between the output port of each Gigabit
Ethernet switch hub and RJ45 port of Receiver unit.
5. Power on the output device first and then the source device.
6. Use dip switch has set up on the transmitter side (Group ID:0001) for each
receiver. (Group ID:0001)
Operating Instructions
How to Connect HDMI Over IP multiple source to multiple
displays
Many Sources to Many Displays Function
1. Connect one HDMI Cable between the HDMI output port of source device and the
HDMI input port of Transmitter unit.
2. Connect one HDMI Cable between the HDMI input port of display and the HDMI
output port of Receiver unit.
3. Connect one CAT5e or better cable between the RJ45 of each Transmitter unit
and RJ45 port of Gigabit Ethernet switch hub.
4. Connect one CAT5e or better cable between each RJ45 port of Gigabit Ethernet
switch hub to RJ45 port of Receiver unit. User can select source channel by setting
up dip switch on each transmitter unit. And select display source for Receiver units
via one remote control.
5. Use DIP switch select change sources .
Operating Instructions
MAINTENANCE
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to
clean this unit.
PRODUCT SERVICE
1) Damage requiring service: The unit should be serviced by qualified service
personnel if:
(a)The DC power supply cord or AC adaptor has been damaged;
(b)Objects or liquids have gotten into the unit;
(c)The unit has been exposed to rain;
(d)The unit does not operate normally or exhibits a marked change in performance;
(e)The unit has been dropped or the cabinet damaged.
2) Servicing Personnel: Do not attempt to service the unit beyond that described
in these operating instructions. Refer all other servicing to authorized servicing
personnel.
3) Replacement parts: When parts need replacing ensure the servicer uses parts
specified by the manufacturer or parts that have the same characteristics as the
original parts. Unauthorized substitutes may result in fire, electric shock, or other
hazards.
4) Safety check: After repairs or service, ask the servicer to perform safety checks
to confirm that the unit is in proper working condition.
Distributed by Adigitalife Distribution Pty Ltd
Ph 0755632055 Fax 0755632044
www.adigitalife.com
Download PDF