User Manual PCM-9310

User Manual
PCM-9310
Intel® Celeron N3160/N3060 SoC,
3.5" SBC, DDR3L, VGA, HDMI,
48-bit LVDS/eDP*, 2GbE, Mini PCIe,
mSATA, SUSI API
Copyright
The documentation and the software included with this product are copyrighted 2016
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel® is a trademark of Intel® Corporation.
AMI is a trademark of American Megatrends, Inc.
IBM, PC, PS/2 and VGA are trademarks of International Business Machines
Corporation.
Microsoft Windows®, DirectX® is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
For more information on this and other Advantech products, please visit our websites
at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://support.advantech.com/
This manual is for the PCM-9310.
PCM-9310 User Manual
Part No. 2006931010
Edition 1
Printed in China
June 2016
ii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
iii
PCM-9310 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manflatterer. Discard used batteries according to the manufacturer's instructions.
Technical Support and Assistance
1.
2.
Visit the Advantech website at http://support.advantech.com where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
PCM-9310 User Manual
iv
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:










1 x PCM-9310 SBC
1 x SATA Cable 30cm
1 x SATA Power Cable 35cm
1 x Audio Cable 20cm
2 x COM Cable 22cm
1 x Heatsink
1 x Startup manual
1 x Mini Jumper Pack
1 x Screw Kit (4pcs screws for miniPCIe)
1 x SUSIAccess Pro package
(p/n: 1700006291)
(p/n: 1700018785)
(p/n: 1700019584)
(p/n: 1701200220)
(p/n: 1960071176T001)
(p/n: 2006931000)
(p/n: 9689000002)
(p/n: 9666525100E)
(p/n: 968EMLSAP1)
If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Optional Accessories
Part number
1960075286T001
1703100260
Description
Heat spreader
Internal USB cable
v
PCM-9310 User Manual
PCM-9310 User Manual
vi
Contents
Chapter
1
General Information ............................1
1.1
1.2
Introduction ............................................................................................... 2
Specifications ............................................................................................ 2
1.2.1 Functional Specifications .............................................................. 2
1.2.2 OS support.................................................................................... 4
1.2.3 Mechanical Specifications............................................................. 4
1.2.4 Electrical Specifications ................................................................ 4
1.2.5 Environmental ............................................................................... 4
Block Diagram........................................................................................... 5
Board layout: dimensions.......................................................................... 5
Figure 1.1 PCM-9310 Mechanical Drawing (Top Side) ............... 5
Figure 1.2 PCM-9310 Mechanical Drawing (Bottom Side) .......... 6
Figure 1.3 PCM-9310 Mechanical Drawing (Coastline)............... 6
1.3
1.4
Chapter
2
Installation............................................7
2.1
Jumpers & Switches.................................................................................. 8
Table 2.1: Jumpers & Switches ................................................... 8
Connectors................................................................................................ 8
Table 2.2: Connectors ................................................................. 8
Locating Connectors ................................................................................. 9
Figure 2.1 PCM-9310 Connector Locations (Top Side)............... 9
Figure 2.2 PCM-9310 Connector Locations (Bottom Side) ......... 9
Setting Jumpers ...................................................................................... 10
2.4.1 AT & ATX (J1)............................................................................. 10
2.4.2 LCD Power (J2) .......................................................................... 11
2.4.3 LVDS VCON Setting (J3)............................................................ 11
2.2
2.3
2.4
Chapter
3
AMI BIOS Setup .................................13
3.1
3.2
Introduction ............................................................................................. 14
Entering Setup ........................................................................................ 15
3.2.1 Main Setup.................................................................................. 15
3.2.2 Advanced BIOS Features Setup................................................. 16
3.2.3 Chipset Configuration ................................................................. 31
3.2.4 Security ....................................................................................... 42
3.2.5 Boot............................................................................................. 43
3.2.6 Save & Exit ................................................................................. 44
4
MIOe Installation ................................45
4.1
Quick Installation Guide: ......................................................................... 46
Appendix A
Pin Assignments ...............................47
A.1
Jumper List.............................................................................................. 48
A.1.1 AT & ATX (J1)............................................................................. 48
A.1.2 LCD Power (J2) .......................................................................... 48
A.1.3 LVDS VCON Setting (J3)............................................................ 49
Connector Pin Definition ......................................................................... 49
Chapter
A.2
vii
PCM-9310 User Manual
Appendix B
System Assignments........................ 67
B.1
System I/O Ports..................................................................................... 68
Table B.1: System I/O Ports ...................................................... 68
1st MB Memory Map............................................................................... 68
Table B.2: 1st MB Memory Map ................................................ 68
Interrupt Assignments ............................................................................. 69
Table B.3: Interrupt assignments............................................... 69
B.2
B.3
PCM-9310 User Manual
viii
Chapter
1
1
General Information
This chapter gives background
information on the PCM-9310.
Sections include:
 Introduction
 Specifications
 Block diagram
 Board layout and dimensions
1.1 Introduction
PCM-9310 is designed using MI/O Extension form factor (compact series, 146 x 102
mm) and powered by the latest generation of Intel® Celeron® N3160 and N3060 processors which have low power features but also good performance computing, especially for multimedia capabilities compared to earlier generations. Meanwhile,
PCM-9310 offers flexible expansion possibilities: two full-size mini PCIe, 1 x Full-size
Mini PCIe w/ SIM holder, and 1 x Full-size mSATA, MIOe with PCIex1, SMBus,
3xUSB2.0, line out, DisplayPort, +12V/ +5V Power, and power interface.
PCM-9310 supports various display interfaces included HDMI, VGA, 48-bit LVDS/
eDP*, and rich I/O: 2 x GbE, SATA, mSATA/SD card, 4xSerial Ports, 2 x USB 3.0 and
4 x USB 2.0.
*This specification is supported upon request.
1.2 Specifications
1.2.1 Functional Specifications

Processor:
– Celeron® N3160 1.6 GHz (burst frequency 2.24 GHz), Quad Cores, Four
Threads
– Celeron® N3060 1.6GHz (burst frequency 2.48 GHz), Dual Cores, Two
Threads
– L2 Cache: 2MB
– Advanced Technologies
* Intel® Virtualization Technology (VT-x)
* Intel® 64 Architecture
* Enhanced Intel SpeedStep Technology
* Intel® Trusted Execution Engine (TXE)
– Power Management
* ACPI 5.0
* System sleep states: S0, S3, S4, S5


System Memory Support
– Non-ECC, DDR3L SODIMM up to 8GB
– 64 bit wide channels
– x8 and x16 DDR3L SDRAM device data widths
– DDR3L with 1600 MT/s
Integrated Graphics Controller
– Controller: Intel® HD Graphics 400
– Graphics HFM (High Frequency Mode): 320MHz
– Graphic Features:
* 3D HW Acceleration: DirectX11.1, OpenGL4.2, OpenCL1.2
* HW Video Decode: H.265/HEVC @ level 5, H.264 @ Level 5.1, MPEG2, MVC, VC1, WMV9, JPEG and VP8
* HW Video Encode: H.264 @ Level 5.1, MVC, JPEG
– Multi-display interfaces: VGA, HDMI, 48-bit LVDS/eDP1
* Supports Extend/ Clone Mode with multi-display device
* Dual display: any two combination between: VGA, HDMI, LVDS
– Triple Display:
* VGA+HDMI+48-bit LVDS
– Specification and Resolution
* VGA: 1920 x 1200 at 60Hz
PCM-9310 User Manual
2
– DirectX* Video Acceleration (DXVA) support for accelerating video
processing
* Full AVC/VC1/MPEG2 Hardware Decode
– OpenGL4.0 support
Chapter 1
* HDMI: HDMI 1.4b with audio, 2560 x 1600 at 60Hz
* LVDS/eDP: 48-bit LVDS up to 1920x1200 at 60Hz,
eDP is supported standard version 1.3 with audio up to 2560 x 1440 (optional)
at 60Hz
– DirectX 11.1, DirectX 11, DirectX 10.1, DirectX 10, DirectX 9 support
Gigabit Ethernet
– Controller: RTL8111E
* 10/100/1000 Mbps
* Energy Efficient Ethernet (EEE) IEEE802.3az support [Low Power Idle (LPI) mode]
* IEEE 1588
* 9.5 KB Jumbo frames supported (Full-duplex)
* Flow Control supported
* Magic packet wake-up enable with unique MAC address

Peripheral interface
– MIOe Expansion
 DisplayPort1
 1 PCIe x1
 3 USB 2.0
 LPC
 HD Audio: Line out
 SMBus
 Power: +5 Vsb/+12 Vsb, Power On, Reset
– 2 Serial-ATA port, up to 6.0 Gb/s (600 MB/s)
* SATA Power: 5V / 12V
– 2 USB 3.0 & 4 x USB2.0
* Two USB3.0 and two USB2.0 on rear I/O, two internal USB2.0
* Support wake-up from sleeping state S3
– 2 RS-232 for COM1/2, 2 RS-232/422/485 for COM3/4 (ESD protection: air
gap ±15kV, contact ±8kV)
– 8-bit Programmable General Purpose Input/ Output from iManager
– 1 SMBus / I2C channel from iManager
– Watchdog timer: Output System Reset, Programmable counter from 1 ~ 255
minutes/ seconds
– Mini PCIe / mSATA
 1 Full-size Mini PCIe with SIM holder
 1 Full-size mSATA


High Definition Audio:
– Intel® High Definition Audio Interface
– High Definition Audio Codec with Realtek proprietary loss-less content protection technology
– Supports 1 Line-input, 1 Line output, 1 Mic-input
BIOS
– AMI UEFI 64 Mbit, BIOS for 64 or 32bit is different, default version is for 64bit
– Default setting is UEFI that can be done by T-P/N
1
: This specification is supported upon request.
3
PCM-9310 User Manual
General Information

1.2.2 OS support
PCM-9310 supports Win10, Win8.1, WES7, Linux kernel 4.1
Win7 only supports Legacy mode and Win8 for UEFI mode.
For further information about OS support of PCM-9310, please visit Advantech
website:
http://support.advantech.com.tw/ or contact the technical support center.
1.2.3 Mechanical Specifications



Dimensions: 146 x 102 mm (5.7 x 4 inches)
Height: top side 19mm, PCB 1.6mm, bottom side 6.8mm, total 27.4mm
Weight: 0.6 kg (1.2 lb) (weight of total package)
1.2.4 Electrical Specifications




Power Requirement: +12 V ± 10% (Default support 2x2pin ATX power connector, DC Jack by T-P/N)
Power Consumption:
– Typical in Window 8.1:
N3160: 0.58 A @ 12 V (7.05 W)
N3060: 0.38 A @ 12 V (4.55 W)
– Max in HCT:
N3160: 1.03A @ 12 V (12.27 W)
N3060: 0.85A @12 V (10.20 W)
Power Consumption Conditions:
– Test software: 3DMark 2013
– Max. load: Measure the maximum current value which system under maximum load (CPU: Top speed, RAM &Graphic: Full loading)
– Idle mode: Measure the current value when system in windows mode and
without running any program
RTC Battery:
– Typical Voltage: 3.0 V
– Normal discharge capacity: 210 mAh
1.2.5 Environmental




Operating temperature: 0 ~ 60°C (32 ~ 140°F)
Operating Humidity: 40°C @ 85% RH Non-Condensing
Storage Temperature: Storage temperature: -40~85°C
Storage Humidity: Relative humidity: 95% @ 60°C
PCM-9310 User Manual
4
DDR3L SODIMM
SATA III
SATA
SATA II*
SATA
Full-size mSATA
DP
Transmitter
VGA
DP
Transmitter
48-bit LVDS
eDP*
PCIe
LPC
2 x USB3.0
USB3
Intel
Pentium/Celeron
SoC
DP
HDMI
SPI
BIOS
PCIe
2 x GbE: RTL8111
PCIe
4 x USB2.0
USB2
ALC892
Audio In/Out
Full-size Mini PCIe
SIM
2 x RS-232
Super I/O
USB2
LPC
2 x RS-232/422/485
LPC
PCIe
8bit GPIO
iManager
SMBus/ I2C
1.4 Board layout: dimensions
Figure 1.1 PCM-9310 Mechanical Drawing (Top Side)
5
PCM-9310 User Manual
General Information
USB2
TPM 2.0*
Chapter 1
1.3 Block Diagram
Figure 1.2 PCM-9310 Mechanical Drawing (Bottom Side)
Figure 1.3 PCM-9310 Mechanical Drawing (Coastline)
PCM-9310 User Manual
6
Chapter
2
2
Installation
This chapter explains the setup
procedures of the PCM-9310 hardware, including instructions on
setting jumpers and connecting
peripherals, switches and indicators. Be sure to read all safety precautions before you begin the
installation procedure.
2.1 Jumpers & Switches
The PCM-9310 has a number of jumpers that allow you to configure your system to
suit your application. The table below lists the functions of the various jumpers.
Table 2.1: Jumpers & Switches
J1
AT & ATX
J2
LCD Power
J3
LVDS VCON Setting
2.2 Connectors
Onboard connectors link the PCM-9310 to external devices such as hard disk drives,
a keyboard, or floppy drives. The table below lists the function of each of the connectors.
Table 2.2: Connectors
Label
Function
CN1
12V Power Input
CN2
12V Power Input (by request)
CN3
DC JACK (by request)
CN4
SO-DIMM
CN5
Power Switch
CN7
Reset
CN8
GPIO
CN9
Audio
CN11
LAN
CN13
VGA
CN14
(reserved) eDP**
CN15
HDMI
CN16
Inverter Power Output
CN17
48 bits LVDS Panel
CN18
mSATA
CN19
Mini PCIE
CN20
SIM
CN21
SATA
CN22
SATA Power
CN23
(reserved) SATA II Power**
CN24
(reserved) SATA II*
CN25
External USB
CN26
Internal USB
CN27
USB3.0x2_9H
CN28
COM3/COM4/RS422/RS485
CN29
COM1/COM2
CN31
System FAN
CN32
SMBus
CN33
Battery
PCM-9310 User Manual
8
CN31 CN33
CN32
CN5
CN22 CN23
J1 CN16
CN24
CN21
CN7
Chapter 2
2.3 Locating Connectors
Installation
CN26
CN4
CN25
CN27
CN15
J3
CN13
CN17
J2
CN1
CN11
Figure 2.1 PCM-9310 Connector Locations (Top Side)
CN8
CN29
CN28
CN9
V
V
V
CN20
CN19
CN18
CN14
Figure 2.2 PCM-9310 Connector Locations (Bottom Side)
9
PCM-9310 User Manual
2.4 Setting Jumpers
You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper, you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2 and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows:
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes. Generally, you
simply need a standard cable to make most connections.
2.4.1 AT & ATX (J1)
J1
AT & ATX
Part Number
1653003201
Footprint
HD_3x2P_79_D
Description
PIN HEADER 3x2P 2.0mm 180D(M) DIP 21N22050
Setting
Function
(1-2)*
AT
(N/A)
ATX
1
2
3
3
5
5
ATX
AT
PCM-9310 User Manual
1
10
LCD Power
Part Number
1653003260
Footprint
HD_3x2P_79
Description
PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Setting
Function
(1-3)*
+3.3V
(3-5)
+5V
(3-4)
+12V
1
1
1
3
3
3
5
5
4
+12V
+5V
+3.3V
Installation
J2
2.4.3 LVDS VCON Setting (J3)
J3
LVDS VCON Setting
Part Number
1653000014
Footprint
HD_2x2P_79
Description
PIN HEADER 2x2P 2.00mm 180D(M) SMD 21N22050
Setting
Function
(1-2)*
3.3V High for VCON on LVDS
(1-3)
Low for VCON on LVDS
1
2
1
3
3
5
5
Low
+3.3V
* This specification is the default setting.
** This specification is supported upon request.
11
Chapter 2
2.4.2 LCD Power (J2)
PCM-9310 User Manual
PCM-9310 User Manual
12
Chapter
3
AMI BIOS Setup
3
3.1 Introduction
AMIBIOS has been integrated into a plethora of motherboards for decades. With the
AMIBIOS Setup program, you can modify BIOS settings and control the various system features. This chapter describes the basic navigation of the PCM-9310 BIOS
setup screens.
AMI BIOS ROM has a built-in Setup program that allows users to modify the basic
system configuration. This information is stored in battery-backed CMOS so it retains
the Setup information when the power is turned off.
PCM-9310 User Manual
14
Turn on the computer and check for the patch code. If there is a number assigned to
the patch code, it means that the BIOS supports your CPU. If there is no number
assigned to the patch code, please contact an Advantech application engineer to
obtain an up-to-date patch code file. This will ensure that your CPU‘s system status is
valid. After ensuring that you have a number assigned to the patch code, press
<DEL> and you will immediately be allowed to enter Setup.
When you first enter the BIOS Setup Utility, you will encounter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab. There are
two Main Setup options. They are described in this section. The Main BIOS Setup
screen is shown below.
The Main BIOS setup screen has two main frames. The left frame displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accompany it.
 System time / System date
Use this option to change the system time and date. Highlight System Time or
System Date using the <Arrow> keys. Enter new values through the keyboard.
Press the <Tab> key or the <Arrow> keys to move between fields. The date
must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS
format.
15
PCM-9310 User Manual
AMI BIOS Setup
3.2.1 Main Setup
Chapter 3
3.2 Entering Setup
3.2.2 Advanced BIOS Features Setup
Select the Advanced tab from the PCM-9310 setup screen to enter the Advanced
BIOS Setup screen. You can select any of the items in the left frame of the screen,
such as CPU Configuration, to go to the sub menu for that item. You can display an
Advanced BIOS Setup option by highlighting it using the <Arrow> keys. All Advanced
BIOS Setup options are described in this section. The Advanced BIOS Setup
screens is shown below. The sub menus are described on the following pages.
PCM-9310 User Manual
16
Chapter 3
3.2.2.1 ACPI Settings
AMI BIOS Setup




Enable ACPI Auto Configuration
Enable or disable BIOS ACPI auto configuration.
Enable Hibernation
Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This
option may be not effective with some OS.
ACPI Sleep State
Select the highest ACPI sleep state the system will enter when the SUSPEND
button is pressed.
Lock Legacy Resources
Enables or Disables Lock of Legacy Resources
17
PCM-9310 User Manual
3.2.2.2 Embedded Controller Configuration





EC Hardware Monitor
This page display all information about system Temperature/Voltage/Current.
Backlight Enable Polarity
This item allows users to set backlight mode.
1st LVDS Backlight control
This item allows users to switch Backlight Control for PWM or DC mode.
Power Saving Mode
This item allows users to set board’s power saving mode when off.
Watch Dog Timer
This item allows users to select EC watchdog timer.
PCM-9310 User Manual
18
Chapter 3
3.2.2.3 Trusted Computing
AMI BIOS Setup

Trusted Computing
Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
19
PCM-9310 User Manual
3.2.2.4 S5 RTC Wake Settings

Wake system from S5
Enable or disable System wake on alarm event. Select FixedTime, system will
wake on the hr::min::sec specified.
PCM-9310 User Manual
20
Chapter 3
3.2.2.5 Serial Port Console Redirection
AMI BIOS Setup


Console Redirection
This item allows users to enable or disable console redirection for Microsoft
Windows Emergency Management Services (EMS).
Console Redirection
This item allows users to configuration console redirection detail settings.
21
PCM-9310 User Manual
3.2.2.6 CPU Configuration




Limit CPUID Maximum
Disabled for Windows XP.
Bi-directional PROCHOT
When a processor thermal sensor trips (either core), the PROCHOT# will be
driven. If bi-direction is enabled, external agents can drive PROCHOT# to throttle the processor.
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities provided
by Vanderpool Technology.
Power Technology
Enable the power management features.
PCM-9310 User Manual
22
Chapter 3
3.2.2.7 PPM Configuration
AMI BIOS Setup


CPU C state Report
Enable/Disable CPU C state report to OS.
Max CPU C-state
This option controls Max C state that the processor will support.
23
PCM-9310 User Manual
3.2.2.8 SATA Configuration





SATA Controller
Enable / Disable SATA Device.
SATA Mode Selection
Determine how SATA controller operate.
SATA Interface Speed
SATA Interface Speed Support Gen1, Gen2 or Gen3.
Aggressive LPM Support
Enable PCH to aggressively enter link power state.
Port 1 / Port 2
Enable / Disable Serial ATA Port 1 / Port 2.
PCM-9310 User Manual
24
Chapter 3
3.2.2.9 PCI Subsystem Settings
AMI BIOS Setup







PCI Latency Timer
Value to be programmed into PCI Latency Timer Register.
PCI-X Latency Timer
Value to be programmed into PCI Latency Timer Register.
VGA Palette Snoop
Enables or Disables VGA Palette Registers Snooping.
PERR# Generation
Enables or Disables PCI Device to Generate PERR#.
SERR# Generation
Enables or Disables PCI Device to Generate SERR#.
Above 4G Decoding
Enables or Disables 64bit capable Devices to be Decoded in Above 4G Address
Space (Only if System Supports 64bit PCI Decoding).
Don’t Reset VC-TC Mapping
If system has Virtual Channels, Software can reset Traffic Class mapping
through Virtual Channels, to it’s default state. Setting this option to Enabled will
not modify VC Resources.
25
PCM-9310 User Manual
3.2.2.10 Network Stack Configuration

Network Stack
Enable/Disable UEFI Network Stack.
PCM-9310 User Manual
26
Chapter 3
3.2.2.11 CSM Configuration
AMI BIOS Setup








CSM Support
Enable/Disable CSM Support.
GateA20 Active
UPON REQUEST - GA20 can be disabled using BIOS services. ALWAYS - do
not allow disabling GA20; this option is useful when any RT code is executed
above 1MB.
INT19 Trap Response
BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE - execute the
trap right away; POSTPONED - execute the trap during legacy boot.
Boot option filter
This option controls Legacy/UEFI ROMs priority.
Network
Controls the execution of UEFI and Legacy PXE OpROM.
Storage
Controls the execution of UEFI and Legacy Storage OpROM.
Video
Controls the execution of UEFI and Legacy Video OpROM.
Other PCI devices
Determines OpROM execution policy for devices other than Network, Storage,
or Video.
27
PCM-9310 User Manual
3.2.2.12 USB Configuration







Legacy USB Support
Enables Legacy USB support. AUTO option disables legacy support if no USB
devices are connected. DISABLE option will keep USB devices available only
for EFI applications.
XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.
USB Mass Storage Driver Support
Enable/Disable USB Mass Storage Driver Support.
Port 60/64 Emulation
Enables I/O port 60h/64h emulation support. This should be enabled for the
complete USB keyboard legacy support for non-USB aware OSes.
USB transfer time-out
Time-out value for control, Bulk, and interrupt transfers.
Device reset time-out
USB mass storage device start unit command time-out.
Device power-up delay
Maximum time the device will take before it properly reports itself to the Host
Controller. 'Auto' uses default value: for a Root port it is 100 ms, for a Hub port
the delay is taken from Hub descriptor.
PCM-9310 User Manual
28
Chapter 3
3.2.2.13 Security Configuration
AMI BIOS Setup



TXE HMRFPO Disable
TXE Firmware Update
TXE EOP Message
Send EOP Message Before Enter OS.
29
PCM-9310 User Manual
3.2.2.14 IT8768E Super I/O Configuration




Serial Port 1 Configuration
Set Parameters of Serial Port 1 (COMA).
Serial Port 2 Configuration
Set Parameters of Serial Port 2 (COMB).
Serial Port 3 Configuration
Set Parameters of Serial Port 3 (COMC).
Serial Port 4 Configuration
Set Parameters of Serial Port 4 (COMD).
PCM-9310 User Manual
30
Chapter 3
3.2.3 Chipset Configuration
AMI BIOS Setup


North Bridge
Details for North Bridge items.
South Bridge
Details for South Bridge items.
31
PCM-9310 User Manual
3.2.3.1 North Bridge





Intel IGD Configuration
Config Intel IGD Settings.
Graphics Power Management Control
Graphics Power Management Control Options.
Memory Configuration Options
MRC EV Setup Option.
AMI Graphic Output Protocol Policy
User Select Monitor Output by Graphic Output Protocol.
Max TOLUD
Maximum Value of TOLUD.
PCM-9310 User Manual
32
Chapter 3
3.2.3.2 Intel IGD Configuration
AMI BIOS Setup








Integrated Graphics Device
Enable: Enable Integrated Graphics Device (IGD) when selected as the Primary
Video Adaptor. Disable : Always disable IGD.
IGD Turbo
Select the IGD Turbo feature, if Auto selected, IGD Turbo will only be enabled
when SOC stepping is B0 or above.
PAVC
Enable/Disable Protected Audio Video Control.
PR3 (For Win 10 only)
Enable/Disable PR3 (For Win 10 only).
DVMT Pre-Allocated
Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the
Internal Graphics Device.
DVMT Total Gfx Mem
Select DVMT 5.0 Total Graphic Memory size used by the Internal Graphics
Device.
Aperture Size
Select the Aperture Size.
GTT Size
Select the GTT Size.
33
PCM-9310 User Manual
3.2.3.3 Graphics Power Management Control


RC6 Render Standby)
Check to enable render standby support.
Power Meter Lock
Enable/Disable Power Meter Lock.
PCM-9310 User Manual
34
Chapter 3
3.2.3.4 Memory Configuration Options
AMI BIOS Setup









DDR DVFS
Enable or disable DDR Dynamic Voltage and Frequency Scaling in MRC.
Memory Frequency Override
Allows override of memory frequency parameters that are automatically
obtained from DDR3 DIMM SPD. May cause memory instability if the selected
frequency is not supported by the memory device. This option has no effect on
systems configured without “UseDIMMSpd’ option.
Frequency A selection
Frequency A selection.
Frequency B selection
Option to Select Frequency B (Min DDR DVFS Frequency).
Dynamic Self Refresh
Enable or disable PUNIT driven DUNIT DDR dynamic self refresh.
DRAM PM5
Enable or disable DRAM PM5 PUNIT configuration.
DDR3 2N Mode
Set the DDR3 mode to 2N. 1N mode is used by default.
MRC Fast Boot
Enable/Disable MRC fast Boot. Forces MRC training to occur when disable.
Scrambler
Enable/Disable Scrambler.
35
PCM-9310 User Manual
3.2.3.5 AMI Graphic Output Protocol Policy

LVDS Panel Type
Select LCD Panel Type.
PCM-9310 User Manual
36
Chapter 3
3.2.3.6 South Bridge
AMI BIOS Setup





Security Configuration
Security Configuration settings.
Azalia Configuration
Azalia HD Audio Options.
USB Configuration
USB Configuration Settings.
PCI Express Configuration
PCI Express Configuration settings.
Restore AC Power Loss
Select AC power state when power is re-applied after a power failure.
37
PCM-9310 User Manual
3.2.3.7 Security Configuration



RTC Lock
Enable or disable bytes 38h-3Fh in the upper and lower 128-byte bank of RTC
RAM lockdown.
BIOS Lock
Enable/Disable the BIOS Lock Enable feature.
Global SMI Lock
Enable or Disable SMI Lock.
PCM-9310 User Manual
38
Chapter 3
3.2.3.8 Azalia Configuration
AMI BIOS Setup


Audio Controller
Control Detection of the Azalia device. Disabled = Azalia will be unconditionally
disabled. Enabled = Azalia will be unconditionally Enabled.
Azalia HDMI Codec
Enable/Disable internal HDMI codec for Azalia.
39
PCM-9310 User Manual
3.2.3.9 USB Configuration


USB2 PHY Power Gating
Configure USB2 PHY Power Gating.
USB3 PHY Power Gating
Configure USB3 PHY Power Gating.
PCM-9310 User Manual
40
Chapter 3
3.2.3.10 PCI Express Configuration
AMI BIOS Setup





PCI Express Port 3 / Port 4
Control the PCI Express Root Port.
Native PCIE Enable
PCI Express Native Support Enable/Disable. This feature is only available in
Vista.
PCIE Wake
Enable or disable PCIE to wake the system from S5.
Onboard LAN1/LAN2 Controller
Select to Enable or Disable Onboard LAN1/LAN2 Controller.
LAN Option ROM
Enabled / Disabled Onboard LAN’s PXE option ROM.
41
PCM-9310 User Manual
3.2.4 Security
Select Security Setup from the PCM-9310 Setup main BIOS setup menu. All Security
Setup options, such as password protection and virus protection are described in this
section. To access the sub menu for the following items, select the item and press
<Enter>:
 Change Administrator / User Password
Select this option and press <ENTER> to access the sub menu, and then type
in the password.
PCM-9310 User Manual
42
Chapter 3
3.2.5 Boot
AMI BIOS Setup






Setup Prompt Timeout
Number of seconds that the firmware will wait before initiating the original
default boot selection. A value of 0 indicates that the default boot selection is to
be initiated immediately on boot. A value of 65535(0xFFFF) indicates that firmware will wait for user input before booting. This means the default boot selection is not automatically started by the firmware.
Bootup NumLock State
Select the keyboard NumLock state.
Quiet Boot
Enables or disables Quiet Boot option.
Boot Option #1
Sets the system boot order.
Fast Boot
Enables or disables boot with initialization of a minimal set of devices required
to launch active boot option. Has no effect for BBS boot options.
New Boot Option Policy
Controls the placement of newly detected UEFI boot options.
43
PCM-9310 User Manual
3.2.6 Save & Exit










Save Changes and Exit
This item allows you to exit system setup after saving the changes.
Discard Changes and Exit
This item allows you to exit system setup without saving any changes.
Save Changes and Reset
This item allows you to reset the system after saving the changes.
Discard Changes and Reset
This item allows you to rest system setup without saving any changes.
Save Changes
This item allows you to save changes done so far to any of the options.
Discard Changes
This item allows you to discard changes done so far to any of the options.
Restore Defaults
This item allows you to restore/load default values for all the options.
Save as User Defaults
This item allows you to save the changes done so far as user defaults.
Restore User Defaults
This item allows you to restore the user defaults to all the options.
Boot Override
Boot device select can override your boot priority.
PCM-9310 User Manual
44
Chapter
4
MIOe Installation
4
The MI/O compact form factor SBC is a new-generation SBC design with a variety of
mechanical improvements. Here is the quick installation guide for our thermal design
and MIOe module installation.
4.1 Quick Installation Guide:
1.
There is a Heatsink / Cooler in the white box inside the package. Carefully
remove the release paper from the thermal pad before installation.
Remove Release Paper
PAD XR-Pe 13.9x13.9x1mm
2.
There are six screws and six studs inside the white box, please install the heatsink into place as per illustration below:
PCM-9310 User Manual
46
Appendix
A
A
Pin Assignments
This appendix contains information of a detailed or specialized
nature.
Sections include:
 Jumper and Connector Tables
A.1 Jumper List
A.1.1 AT & ATX (J1)
J1
AT & ATX
Part Number
1653003201
Footprint
HD_3x2P_79_D
Description
PIN HEADER 3x2P 2.0mm 180D(M) DIP 21N22050
Setting
Function
(1-2)*
AT
(N/A)
ATX
1
2
1
3
3
5
5
ATX
AT
A.1.2 LCD Power (J2)
J2
LCD Power
Part Number
1653003260
Footprint
HD_3x2P_79
Description
PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Setting
Function
(1-3)*
+3.3V
(3-5)
+5V
(3-4)
+12V
1
1
1
3
3
3
5
5
+3.3V
PCM-9310 User Manual
+5V
48
4
+12V
J3
LVDS VCON Setting
Part Number
1653000014
Footprint
HD_2x2P_79
Description
PIN HEADER 2x2P 2.00mm 180D(M) SMD 21N22050
Setting
Function
(1-2)*
3.3V High for VCON on LVDS
(1-3)
Low for VCON on LVDS
1
2
1
3
3
5
5
Low
+3.3V
A.2 Connector Pin Definition
CN1
12V Power Input
Part Number
1655003865
Footprint
WF_2x2P_165_BOX_RA_D_740SP
Description
ATX PWRCONN 2x2P 4.2mm 90D(M) DIP 740-77-04TS50
Pin
Pin Name
1
GND
2
GND
3
+12V
4
+12V
49
PCM-9310 User Manual
Appendix A Pin Assignments
A.1.3 LVDS VCON Setting (J3)
CN2
12V Power Input (by request)
Part Number
1655004584-01
Footprint
WF_2x2P_165_BOX_D
Description
ATX PWR CONN. 2x2P 4.2mm 180D(M) DIP 24W4310-04S
Pin
Pin Name
1
GND
2
GND
3
+12V
4
+12V
CN3
DCJACK (by request)
Part Number
1652005624
Footprint
PJ_2P_2DC-G213B200
Description
DC POWER JACK 2.5mm 90D(M) DIP 2DC-G213B200
Pin
Pin Name
1
+12V
2
GND
CN4
SO-DIMM
Part Number
1651002088
Footprint
SODIMMDDR3_204P_AS0A626-HA
Description
DDR3 SODIMM H=9.2mm 204P SMD AS0A626-HASN-7H
Pin
Pin Name
CN5
Power Switch
Part Number
1655302020
Footprint
WF_2P_79_BOX_R1_D
Description
WAFER BOX 2P 2.0mm 180D(M) DIP A2001WV2-2P
Pin
Pin Name
1
PSIN
2
GND
PCM-9310 User Manual
50
Reset
Part Number
1655302020
Footprint
WF_2P_79_BOX_R1_D
Description
WAFER BOX 2P 2.0mm 180D(M) DIP A2001WV2-2P
Pin
Pin Name
1
RESET#
2
GND
CN8
GPIO
Part Number
1653004099
Footprint
HD_5x2P_79_23N685B-10M10
Description
BOX HEADER 5x2P 2.00mm 180D(M) SMD 23N685B-10M10
Pin
Pin Name
1
+5V
2
GPIO4
3
GPIO0
4
GPIO5
5
GPIO1
6
GPIO6
7
GPIO2
8
GPIO7
9
GPIO3
10
GND
51
PCM-9310 User Manual
Appendix A Pin Assignments
CN7
CN9
Audio
Part Number
1653004099
Footprint
HD_5x2P_79_23N685B-10M10
Description
BOX HEADER 5x2P 2.00mm 180D(M) SMD 23N685B-10M10
Pin
Pin Name
1
LOUTR
2
LINR
3
GND
4
GND
5
LOUTL
6
LINL
7
GND
8
GND
9
MIC1R
10
MIC1L
Matching Cable: 1703100152
CN11
LAN
Part Number
1652003274
Footprint
RJ45_28P_RTB-19GB9J1A
Description
PHONE JACK RJ45 28P DIP RTB-19GB9J1A
Pin
Pin Name
1
TX+(10/100),BI_DA+(GHz)
2
TX-(10/100),BI_DA-(GHz)
3
RX+(10/100),BI_DB+(GHz)
4
BI_DC+(GHz)
5
BI_DC-(GHz)
6
RX-(10/100),BI_DB-(GHz)
7
BI_DD+(GHz)
8
BI_DD-(GHz)
PCM-9310 User Manual
52
VGA
Part Number
1654000055
Footprint
DBVGA-VF5MS
Description
D-SUB Conn. 15P 90D(F) DIP 070242FR015S200ZU
Pin
Pin Name
1
RED
2
GREEN
3
BLUE
4
NC
5
GND
6
GND
7
GND
8
GND
9
+5V
10
GND
11
NC
12
DDAT
13
HSYNC
14
VSYNC
15
DCLK
CN14
(reserved) eDP**
Part Number
00
Footprint
SPH10X2
Description
Pin
Pin Name
1
GND
2
GND
3
EDP_PANEL_z_TX0-
4
EDP_PANEL_z_TX3-
5
EDP_PANEL_z_TX0+
6
EDP_PANEL_z_TX3+
7
GND
8
HDMI1_DDAT
9
EDP_PANEL_z_TX1-
10
HDMI1_DCLK
11
EDP_PANEL_z_TX1+
12
EDP_PANEL_z_AUX-
13
GND
53
PCM-9310 User Manual
Appendix A Pin Assignments
CN13
14
EDP_PANEL_z_AUX+
15
EDP_PANEL_z_TX2-
16
GND
17
EDP_PANEL_z_TX2+
18
EDP_PANEL_HPD
19
+V_eDP_CONN
20
+V_eDP_CONN
** This specification is supported upon request.
CN15
HDMI
Part Number
1654011175-01
Footprint
HDMI_19P_QJ51191-LFB4-7F
Description
Pin
Pin Name
1
TMDS Data2+
2
TMDS Data2 Shield
3
TMDS Data2–
4
TMDS Data1+
5
TMDS Data1 Shield
6
TMDS Data1–
7
TMDS Data0+
8
TMDS Data0 Shield
9
TMDS Data0–
10
TMDS Clock+
11
TMDS Clock Shield
12
TMDS Clock–
13
Reserved
14
Reserved
15
SCL
16
SDA
17
DDC Ground
18
+5V Power
19
Hot Plug Detect
PCM-9310 User Manual
54
Inverter Power Output
Part Number
1655000453
Footprint
WHL5V-2M-24W1140
Description
WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI
Pin
Pin Name
1
+12V
2
GND
3
ENABKL
4
VBR
5
+5V
CN17
48 bits LVDS Panel
Part Number
1653920200
Footprint
SPH20X2
Description
B/B Conn. 40P 1.25mm 90D SMD DF13-40DP-1.25V(91)
Pin
Pin Name
1
+5V or +3.3V
2
+5V or +3.3V
3
GND
4
GND
5
+5V or +3.3V
6
+5V or +3.3V
7
LVDS0_D0-
8
LVDS1_D0-
9
LVDS0_D0+
10
LVDS1_D0+
11
GND
12
GND
13
LVDS0_D1-
14
LVDS1_D1-
15
LVDS0_D1+
16
LVDS1_D1+
17
GND
18
GND
19
LVDS0_D2-
20
LVDS1_D2-
21
LVDS0_D2+
22
LVDS1_D2+
23
GND
55
PCM-9310 User Manual
Appendix A Pin Assignments
CN16
24
GND
25
LVDS0_CLK-
26
LVDS1_CLK-
CN17
48 bits LVDS Panel
Part Number
1653920200
Footprint
SPH20X2
Description
B/B Conn. 40P 1.25mm 90D SMD DF13-40DP-1.25V(91)
Pin
Pin Name
27
LVDS0_CLK+
28
LVDS1_CLK+
29
GND
30
GND
31
NC
32
NC
33
GND
34
GND
35
LVDS0_D3-
36
LVDS1_D3-
37
LVDS0_D3+
38
LVDS1_D3+
39
NC
40
VCON
PCM-9310 User Manual
56
mSATA
Part Number
00A00000770
Footprint
MINIPCIE_HALF_PICO_ITX
Appendix A Pin Assignments
CN18
Description
Pin
Pin Name
1
WAKE#
2
+3.3VSB
3
NC
4
GND
5
NC
6
+1.5V
7
NC
8
UIM_PWR
9
GND
10
UIM_DATA
11
REFCLK-
12
UIM_CLK
13
REFCLK+
14
UIM_RESET
15
GND
16
UIM_VPP
17
NC
18
GND
19
NC
20
W_DISABLE#
21
GND
22
PERST#
23
PERn0
24
+3.3VSB
25
PERp0
26
GND
57
PCM-9310 User Manual
CN18
Mini PCIE
Part Number
00A00000770
Footprint
MINIPCIE_HALF_PICO_ITX
Description
Pin
Pin Name
27
GND
28
+1.5V
29
GND
30
SMB_CLK
31
PETn0
32
SMB_DAT
33
PETp0
34
GND
35
GND
36
USB D-
37
GND
38
USB D+
39
+3.3VSB
40
GND
41
+3.3VSB
42
NC
43
SEL
44
NC
45
NC
46
NC
47
NC
48
+1.5V
49
NC
50
GND
51
NC
52
+3.3VSB
PCM-9310 User Manual
58
Mini PCIE
Part Number
00A00000770
Footprint
MINIPCIE_HALF_PICO_ITX
Appendix A Pin Assignments
CN19
Description
Pin
Pin Name
1
WAKE#
2
+3.3VSB
3
NC
4
GND
5
NC
6
+1.5V
7
NC
8
UIM_PWR
9
GND
10
UIM_DATA
11
REFCLK-
12
UIM_CLK
13
REFCLK+
14
UIM_RESET
15
GND
16
UIM_VPP
17
NC
18
GND
19
NC
20
W_DISABLE#
21
GND
22
PERST#
23
PERn0
24
+3.3VSB
25
PERp0
26
GND
CN19
Mini PCIE
Part Number
00A00000770
Footprint
MINIPCIE_HALF_PICO_ITX
Description
Pin
Pin Name
27
GND
28
+1.5V
29
GND
30
SMB_CLK
31
PETn0
32
SMB_DAT
33
PETp0
59
PCM-9310 User Manual
34
GND
35
GND
36
USB D-
37
GND
38
USB D+
39
+3.3VSB
40
GND
41
+3.3VSB
42
NC
43
SEL
44
NC
45
NC
46
NC
47
NC
48
+1.5V
49
NC
50
GND
51
NC
52
+3.3VSB
CN20
SIM
Part Number
1654010809-01
Footprint
SIM_6P_5210622-SINR03
Description
SIM card conn. 6p 2.54mm 90D(F) SMD 5210622-SINR
Pin
Pin Name
C1
UIM_PWR
C2
UIM_RESET
C3
UIM_CLK
C5
GND
C6
UIM_VPP
C7
UIM_DATA
PCM-9310 User Manual
60
SATA
Part Number
1654011616-01
Footprint
SATA_7P_WATF-07DBN6SB1U
Appendix A Pin Assignments
CN21
Description
Pin
Pin Name
1
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
CN22
SATA Power
Part Number
1655001154
Footprint
WF_4P_98_BOX_R1_D
Description
WAFER BOX 4P 2.50mm 180D(M) DIP 24W1170-04S10-01
Pin
Pin Name
1
+5V
2
GND
3
GND
4
+12V
61
PCM-9310 User Manual
CN23
(reserved) SATA II Power**
Part Number
00
Footprint
WF_4P_98_BOX_R1_D
Description
Pin
Pin Name
1
+5V
2
GND
3
GND
4
+12V
** This specification is supported upon request.
CN24
(reserved) SATA II**
Part Number
00
Footprint
SATA_7P_WATF-07DBN6SB1U
Description
Pin
Pin Name
1
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
** This specification is supported upon request.
PCM-9310 User Manual
62
External USB
Part Number
1654009513
Footprint
USB_8P_UB1112C-8FDE-4F
Description
USB CONN. 8P 2.0mm 90D DIP UB1112C-8FDE-4F
Pin
Pin Name
1
+5V
2
D-
3
D+
4
GND
CN26
Internal USB
Part Number
1653003718
Footprint
HD_5x2P_79_RA_N10_21N22050
Description
PIN HEADER 5x2P 2.00mm 90D(M) SMD 21N22050
Pin
Pin Name
1
+5V
2
+5V
3
A_D-
4
B_D-
5
A_D+
6
B_D+
7
GND
8
GND
9
GND
Matching Cable: 1703100121 1703100260
63
PCM-9310 User Manual
Appendix A Pin Assignments
CN25
CN27
USB3.0x2_9H
Part Number
1654010969-01
Footprint
USB_9x2P_UEA1112C-8HS6-4F
Description
Pin
Pin Name
CN28
COM3/COM4/RS422/RS485
Part Number
1653004793
Footprint
HD_10x2P_79_23N685B-20M10
Description
BOX HEADER 10x2P 2.0mm 180D(M)SMD 23N685B-20M10B
Pin
Pin Name
1
422TX3-/485D3-/DCD3#
2
DSR3#
3
422TX3+/485D3+/RXD3
4
RTS3#
5
422RX3+/TXD3
6
CTS3#
7
422RX3-/DTR3#
8
RI3#
9
GND
10
GND
11
422TX4-/485D4-/DCD4#
12
DSR4#
13
422TX4+/485D4+/RXD4
14
RTS4#
15
422RX4+/TXD4
16
CTS4#
17
422RX4-/DTR4#
18
RI4#
19
GND
20
GND
PCM-9310 User Manual
64
COM1/COM2
Part Number
1653004793
Footprint
HD_10x2P_79_23N685B-20M10
Description
BOX HEADER 10x2P 2.0mm 180D(M)SMD 23N685B-20M10B
Pin
Pin Name
1
DCD1#
2
DSR1#
3
RXD1
4
RTS1#
5
TXD1
6
CTS1#
7
DTR1#
8
RI1#
9
GND
10
GND
11
DCD2#
12
DSR2#
13
RXD2
14
RTS2#
15
TXD2
16
CTS2#
17
DTR2#
18
RI2#
19
GND
20
GND
Matching Cable: 1701200220
65
PCM-9310 User Manual
Appendix A Pin Assignments
CN29
CN31
System FAN
Part Number
1655003010
Footprint
WHP3VA
Description
Wafer 2.54mm 3P 180D(M) DIP 22-27-2031
Pin
Pin Name
1
GND
2
+12V
3
NC
CN32
SMBus
Part Number
1655904020
Footprint
FPC4V-125M
Description
WAFER 4P 1.25mm 180D(M) SMD 85205-04001
Pin
Pin Name
1
GND
2
SMB_DAT
3
SMB_CLK
4
+5V
CN33
Battery
Part Number
1655902032
Footprint
WHL2V-125
Description
WAFER BOX 2P 1.25mm 180D(M) DIP 53047-0210
Pin
Pin Name
1
+3V
2
GND
PCM-9310 User Manual
66
Appendix
B
B
System Assignments
This appendix contains information of a detailed nature.
Sections include:
 System I/O Ports
 1st MB Memory Map
 Interrupt Assignments
B.1 System I/O Ports
Table B.1: System I/O Ports
Addr. Range (Hex)
Device
20–2D
Interrupt Controller
2E – 2F
Motherboard resources
30 – 3D
Interrupt Controller
40 – 43
System timer
4E – 4F
Motherboard resources
50 – 53
System timer
60 – 67
Motherboard resources
70 - 7F
System CMOS/real time clock
80 - 92
Motherboard resources
A0 – AD
Interrupt Controller
B0 – BD
Interrupt Controller
272 – 273
Motherboard resources
290 – 29F
Embedded Controller resources
2E8 – 2EF
COM4
2F8 – 2FF
COM2
3B0 – 3DF
Intel® HD Graphics
3E8 – 3EF
COM3
3F8 – 3FF
COM1
400 – 47F
Motherboard resources
4D0 – 4D1
Interrupt Controller
500 – 57F
Motherboard resources
B.2 1st MB Memory Map
Table B.2: 1st MB Memory Map
Addr. Range (Hex)
Device
A0000h - BFFFFh
Intel® HD Graphics
A0000h - BFFFFh
PCI Bus
C0000h - DFFFFh
PCI Bus
E0000h - FFFFFh
PCI Bus
90400000 – 905FFFFF Intel® Trusted Execution Engine Interface
E0000000 - FEFFFFFF System resources
PCM-9310 User Manual
68
Table B.3: Interrupt assignments
Interrupt#
Interrupt source
NMI
Parity error detected
IRQ0
System timer
IRQ1
Using SERIRQ, Keyboard Emulation
IRQ2
Slave controller INTR output
IRQ3
Communications Port (COM2)
IRQ4
Communications Port (COM1)
IRQ5
Communications Port (COM3) / iManager WatchDog IRQ
IRQ6
Available
IRQ7
Communications Port (COM4)
IRQ8
Internal RTC or HPET
IRQ9
Microsoft ACPI-Compliant System
IRQ10
Available
IRQ11
Available
IRQ12
Available
IRQ13
Numeric data processor
IRQ14
SATA controller
IRQ15
SATA controller
69
PCM-9310 User Manual
Appendix B System Assignments
B.3 Interrupt Assignments
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2016
Download PDF