Datasheet_CatLinc VID SVID HD Datasheet_v2

CatLinc™ VID SVID HD
CAT5 Signal Distribution System
Transmitter/Receiver pair sends Composite Video, S-Video, or Component Video over CAT5/6
CatLinc SVID
CatLinc HD
CatLinc VID Transmitter and Receiver
FEATURES
Also Available from SP Controls
CatLinc VGA
VGA over CAT5.
CatLinc VGA-L
VGA over CAT5. Includes local
loop for monitor.
CatLinc DA8
Splits any CatLinc signal to as
many as 8 receivers.
CatLinc DA8
Splits any CatLinc signal to as
many as 8 receivers
CatLinc RS232
RS-232 to CAT5.
Simple
and
Intuitive
SP Controls, Inc.
930 Linden Avenue
South San Francisco
California 94080
phone: (877) 367-8444
fax: (650) 392-7881
email: help@spcontrols.com
The CatLinc VID, SVID, and HD extend video
signal up to 365m/1200ft over standard
CAT5, CAT5e, or CAT6 twisted pair cable. For
shorter distances(110m/350ft or less), system
power may be attached to either the
Transmitter or Receiver. For distances
greater than 110m/350ft, the CatLinc
Transmitter and Receiver must both be
powered. In this case, an additional power
supply must be separately ordered (part no.
CatLinc PS).
CATLINC VID allows composite video
connection and unbalanced stereo audio
connection between two devices using
CAT5, CAT5e, or CAT6 twisted pair cable.
The CatLinc VID supports NTSC, PAL, or
SECAM video signals. Connection is made
to devices using 3 standard RCAconnectors.
CATLINC SVID allows S-Video
(YC)connection between two devices using
CAT5, CAT5e, or CAT6 twisted pair cable.
Connection is made to devices using
standard S-Video mini-DIN connectors.
CATLINC HD allows component video (Y, PB,
PR or YUV) connection between two
devices using CAT5, CAT5e, or CAT6 twisted
pair cable. Connection is made to devices
using 3 standard RCAconnectors. No
configuration is necessary.
SPControls always recommends use of
shielded cable for all models.
TECHNICAL SPECIFICATIONS
Power:
9V DC@030 mA UL Approved
Power Connector:
3.5mm O.D./1.3mm I.D. Center
pos(d)
Power Connector Requirements
@0-350 ft/0-110m:
1 power supply (either end)
@351-1200 ft/111-365m:
2 power supply (both ends)
Video – Gain
Unity
Video Input/Output
Signal Type
CatLinc VID:
Composite video
CatLinc SVID:
S-video
CatLinc HD:
Composite video
Connectors:
CatLinc VID:
3 male RCA, RJ-45
CatLinc SVID:
1 mini-DIN, RJ-45
CatLinc HD:
3 male RCA, RJ-45
Nominal Level
CatLinc VID:
0.7V p-p
CatLinc SVID:
1.0V p-p
CatLinc HD:
Y: 1.0V p-p, C:0.3V p-p
Y: 1.0V p-p, PB (CB):
Minimum/Maximum Levels:
Impedance (all models):
Sync (all models):
0.7V p-p, PR (CR): 0.7V p-p
0.3V to 1.5V p-p
75 ohms
NTSC 3.58, NTSC 4.43, PAL, SECAM
© 2015 SP Controls, Inc. All rights reserved. CatLinc™ and the SP Controls switch logo are trademarks of SP Controls, Inc.
Audio – CatLinc VID only
Connectors;
Gain:
Frequency response (-3dB):
Input impedance:
Output impedance:
THD+N@0dBu:
Max level in:
Output clip level:
Output noise:
Cross-talk:
Dynamic range:
Signal-to-noise ratio (min):
Size (metal housing):
VGA Cable Length (approx.):
Shipping Weight:
Optional Accessories:
UL Listed
2 male RCA
Unity
2Hz - 100 kHz
20 kOhms
75 Ohms
0.008%
+10.5dBu
-86dBu
-86dBu
-78dBu
95dB
95dB
0.95" (h) x 1.15" (w) x 2.5" (d)
6”
2.0 lb
CatLinc PS (additional power
supply)
Download PDF