9010,STYLUS-7040 /μ -7040,STYLUS

DIGITAL CAMERA
STYLUS-9010 /
STYLUS-7040 /
STYLUS-5010 /
μ-9010
μ-7040
μ-5010
Instruction Manual
● Thank you for purchasing an Olympus digital camera. Before you start to
use your new camera, please read these instructions carefully to enjoy
optimum performance and a longer service life. Keep this manual in a
safe place for future reference.
● The application software and instruction manual PDF file are stored on
the internal memory of the camera.
● We recommend that you take test shots to get accustomed to your
camera before taking important photographs.
● In the interest of continually improving products, Olympus reserves the
right to update or modify information contained in this manual.
● The screen and camera illustrations shown in this manual were produced
during the development stages and may differ from the actual product.
Unless otherwise specified, the explanation about these illustrations is
provided for STYLUS-9010/μ-9010.
Step
1
Checking the contents of the box
or
Strap
*
Lithium Ion Battery*
STYLUS-9010/μ-9010: LI-50B
STYLUS-7040/μ-7040 and STYLUS-5010/μ-5010: LI-42B
Digital camera
or
USB cable
AV cable
USB-AC adapter (F-2AC)
Other accessories not shown: Warranty card
Contents may vary depending on purchase location.
Step
2
Step
3
Preparing the Camera
Shooting and Playing Back Images
“Preparing the Camera” (p. 10)
“Shooting, Playback, and Erasing” (p. 15)
Step
4
Step
5
How to Use the Camera
Printing
“Camera Settings” (p. 3)
“Direct printing (PictBridge)” (p. 47)
“Print Reservations (DPOF)” (p. 50)
Contents
¾ Names of Parts .............................. 6
¾ Menus for Playback, Editing, and
Printing Functions ....................... 34
¾ Preparing the Camera ................. 10
¾ Menus for Other Camera
¾ Shooting, Playback, and
Settings ........................................ 40
Erasing ......................................... 15
¾ Printing ......................................... 47
¾ Using Shooting Modes................ 21
¾ Usage Tips ................................... 52
¾ Using Shooting Functions .......... 26
¾ Appendix ...................................... 57
¾ Menus for Shooting Functions ... 30
2
EN
Camera Settings
Using the Direct Buttons
Frequently used functions can be accessed using the direct buttons.
Operation guide
The symbols FGHI displayed for image selections
and settings indicate that the wheel controller is to
be used by pressing, not turning, the wheel controller
sections shown below.
4/30
X
Y
M D
TIME
2010 . 02 . 26 12 : 30
CANCEL MENU
NORM 14M
FILE 100 0004
’10/02/26 12:30
Y/M/D
SET OK
PRINT OK
MORE
SINGLE PRINT
Wheel controller
F (up) /
INFO button (changing
information display) (p. 17, 19)
Shutter button (p. 15, 52)
H (left)
I (right)
Zoom buttons (p. 16, 19)
A button
G (down) /
D button (erase) (p. 18)
Movie record button (p. 16)
q button (switching
between shooting and
playback) (p. 16, 17, 41)
m button (p. 4)
Operation guides displayed at the bottom of the screen
indicate that the m button, A button, or zoom
buttons can be used.
1
IMAGE SIZE
2
COMPRESSION NORMAL
SHADOW ADJUST
AUTO
AF MODE
FACE/iESP
ESP
ESP/
FINE ZOOM
OFF
DIGITAL ZOOM
OFF
1
2
3
EXIT MENU
14M
SEL. IMAGE
SET OK
E button (camera guide/
menu guide) (p. 20)
SET OK
OK
ERASE/CANCEL MENU
Operation guide
EN
3
Using the Menu
Use the menu to change camera settings such as the shooting mode.
Press the m button to display the function menu. The function menu can be used to set frequently
used shooting and playback functions such as shooting mode.
Selected option
Shooting
PROGRAM AUTO
P
Shooting
mode
4
● The [SETUP] menu is displayed.
IMAGE SIZE
2
COMPRESSION NORMAL
SHADOW ADJUST
AUTO
AF MODE
FACE/iESP
ESP
ESP/
FINE ZOOM
OFF
DIGITAL ZOOM
OFF
3
There may be additional operations.
“Menu Settings” (p. 30 to 46)
1
X
2
WORLD TIME
POWER SAVE
1
X
2
WORLD TIME
POWER SAVE
Submenu 1
--.--.-- --:--
1
X
x
2
WORLD TIME
--.--.-- --:-x
2
3
EXIT MENU
5
OFF
POWER SAVE
1
2
2
3
OFF
3
SET OK
EXIT MENU
SET OK
Use FG to select the desired submenu 1
and then press the A button.
Submenu 2
Press the m button to complete the
setting.
Some functions cannot be used in some
shooting modes. In such cases, the
following message is displayed after
setting.
1
IMAGE SIZE
2
COMPRESSION NORMAL
SHADOW ADJUST
AUTO
CONFLICTING
SETTINGS
AF
MODE
iESP
ESP/*1
ESP
FINE ZOOM
OFF
DIGITAL ZOOM
OFF
1
2
1
X
2
WORLD TIME
--.--.-- --:--
1
x
2
TV OUT
POWER SAVE
X
--.--.---:-POWER
SAVE
WORLD TIME
HOME
TV OUT
OFF
1
1
2
VIDEO OUT
POWER SAVEOFF OFF
ON
2
3
EXIT MENU
SET OK
TV OUT
1
EXIT MENU
EN
x
ON
1
TV OUT
4
--.--.-- --:--
TV OUT
SET OK
Press H to select the page tabs. Use FG
to select the desired page tab and press I.
Page tab
3
to the previous screen.
14M
EXIT MENU
2
Use FG to select the desired submenu 2
and then press the A button.
● Once a setting is selected, the display returns
1
2
SETUP
Use FG to select a menu and press
the A button.
In the [SETUP] menu, various camera functions can be set,
including shooting and playback functions not displayed in the
function menu, and other settings such as date, time and screen
display.
Select [SETUP] and then press the A
button.
1
BEAUTY FIX
EDIT
ERASE
o [SETUP]
menu
4 14M
To select the shooting mode
Use HI to select the shooting mode and
press the A button.
To select the function menu
Use FG to select a menu and use HI to
select a menu option. Press the A button to
set the function menu.
SLIDESHOW
PHOTO SURFING
EVENT
Function
menu
0.0
WB
AUTO
ISO
AUTO
1
Playback
3
SET OK
EXIT MENU
SET OK
3
EXIT MENU
14M
SET OK
Menu Index
Menus for Shooting Functions
P
PROGRAM AUTO
0.0
WB
AUTO
ISO
AUTO
4 14M
1
2
3
4
5
6
7
8
9
1
IMAGE SIZE
2
COMPRESSION 1 NORMAL
R
SHADOW ADJUST
AUTO
2 IMAGE STABILIZER
AF MODE
FACE/iESP
REC VIEW
ESP
ESP/
PIC ORIENTATION
FINE ZOOM
OFF
1 ICON GUIDE
DIGITAL ZOOM
OFF
1
2
3
14M
1
2
OFF
ON
IMAGE SIZE
ON
IMAGE QUALITY
ON
IS MOVIE MODE
ON
R
OFF
ON
2
EXIT MENU
SET OK
3
1
2
EXIT MENU
3
SET OK
EXIT MENU
1 Shooting mode
P (PROGRAM AUTO) .......p. 15
M (iAUTO) ....................p. 21
s (SCENE MODE) ......p. 21
P (MAGIC FILTER) .....p. 22
p (PANORAMA) ...............p. 23
Q(BEAUTY) ................p. 25
2 Flash..................................p. 26
3 Macro ................................p. 26
4 Self-timer ...........................p. 27
5 Exposure compensation ....p. 27
6 White balance....................p. 27
VGA
NORMAL
7 ISO ....................................p. 28
8 Drive ..................................p. 29
9 o (SETUP)
IMAGE SIZE (Still images)
.......................................p. 30
IMAGE SIZE (Movies) .......p. 30
COMPRESSION (Still images)
.......................................p. 30
IMAGE QUALITY (Movies)
.......................................p. 30
SHADOW ADJUST ...........p. 31
AF MODE ..........................p. 31
SET OK
ESP/n ............................p. 31
FINE ZOOM ......................p. 32
DIGITAL ZOOM .................p. 32
R (Still images) ..................p. 32
R (Movies) .........................p. 32
IMAGE STABILIZER
(Still images)/
IS MOVIE MODE
(Movies).............................p. 32
REC VIEW.........................p. 33
PIC ORIENTATION ...........p. 33
ICON GUIDE .....................p. 33
Menus for Playback, Editing, and Printing Functions
SLIDESHOW
PHOTO SURFING
EVENT
COLLECTION
BEAUTY FIX
EDIT
ERASE
1
2
3
4
5
6
7
8
1
2
PRINT ORDER
0
y
R
1
2
3
EXIT MENU
SET OK
SETUP
1
2
3
4
5
SLIDESHOW .....................p. 34
PHOTO SURFING.............p. 34
EVENT q ........................p. 35
COLLECTION q .............p. 35
BEAUTY FIX......................p. 36
6 EDIT ..................................p. 36
7 ERASE ..............................p. 38
8 o (SETUP)
PRINT ORDER ..................p. 38
0 (Protect) .....................p. 38
y (Rotate).........................p. 38
R (Add sound to still images)
.......................................p. 39
Menus for Other Camera Settings
1
2
1
2
3
INTERNAL/SD
MEMORY FORMAT
DATA REPAIR
COPY
AUTO
ENGLISH
1
2
RESET
3
USB CONNECTION
EXIT MENU
PC
SET OK
1 r (Settings 1)
INTERNAL/SD...................p. 40
MEMORY FORMAT/
FORMAT............................p. 40
DATA REPAIR ...................p. 40
u COPY.....................p. 40
l (Language) ................p. 40
RESET...............................p. 41
USB CONNECTION ..........p. 41
2 s (Settings 2)
q POWER ON ................p. 41
SAVE SETTINGS ..............p. 41
PW ON SETUP .................p. 41
SOUND SETTINGS ..........p. 42
FILE NAME .......................p. 42
PIXEL MAPPING ...............p. 43
s (Monitor) .....................p. 43
3 t (Settings 3)
X (Date/time) ..................p. 43
WORLD TIME....................p. 44
TV OUT .............................p. 44
POWER SAVE...................p. 46
EN
5
Names of Parts
Camera unit
1
8
2
9
3
4
10
5
6
11
7
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
3
2
3
2
8
9
8
9
12
12
1
2
3
4
5
6
*1
6
EN
Connector cover ..................... p. 11, 12
HDMI micro connector ................. p. 46
Multi-connector........... p. 11, 12, 45, 47
Strap eyelet .................................... p. 7
Flash ............................................ p. 26
Battery/card compartment lock*1
.................................................... p. 10
STYLUS-9010/μ-9010 and STYLUS-7040/μ-7040
only
7
8
9
10
11
12
*2
Battery/card compartment cover
.................................................... p. 10
Self-timer lamp ............................. p. 27
Microphone ............................ p. 32, 39
Lens ............................................. p. 57
Tripod socket
Speaker*2
STYLUS-7040/μ-7040 and STYLUS-5010/μ-5010
1
6
2
7
3
8
9
10
11
4
5
1
2
3
4
5
6
7
8
9
*
12
Speaker*
n button........................ p. 13, 15
Zoom buttons ......................... p. 16, 19
Monitor ......................... p. 8, 15, 43, 52
m button .............................. p. 3, 4
Shutter button......................... p. 15, 52
Indicator lamp......................... p. 11, 12
Movie record button ..................... p. 16
q button (switching between shooting
and playback) ................... p. 16, 17, 41
10
11
12
A button (OK) ............................... p. 3
Wheel controller ............................. p. 3
INFO button (changing information
display) ............................. p. 17, 19
D button (erase) .................... p. 18
E button
(camera guide/menu guide) ......... p. 20
STYLUS-9010/μ-9010
Attaching the camera strap
Pull the strap tight so that it does not come loose.
EN
7
Monitor
Shooting mode display
1
2
P
24
23
22
21
20
19
18
0.0
P
WB
AUTO
ISO
AUTO
00:34
4 14M NORM
3
4
5
6
7
8
9
10
17 16 15 14 13 12 11
1
2
3
4
5
6
7
8
9
10
11
12
13
8
EN
1/100
F3.2
26
25
Battery check ......................... p. 12, 53
Shooting mode ....................... p. 15, 21
Flash ............................................ p. 26
Flash standby/flash charge .......... p. 52
Macro/super macro ...................... p. 26
Self-timer ...................................... p. 27
Exposure compensation............... p. 27
White balance .............................. p. 27
ISO ............................................... p. 28
Drive ............................................. p. 29
[SETUP] menu ........................... p. 4, 5
World time .................................... p. 44
Image stabilization (still images)/
Digital image stabilization (movies)
.................................................... p. 32
Metering ....................................... p. 31
14
15
16
17
18
19
20
21
22
23
24
25
26
Shadow Adjustment Technology
.................................................... p. 31
Compression (still images) ..... p. 30, 60
Image size (still images) ......... p. 30, 60
Number of storable still pictures
(still images) ................................. p. 15
Current memory ........................... p. 59
Movie recording icon .................... p. 16
Remaining recording time (movies)
Image size (movies) ............... p. 30, 61
Histogram ..................................... p. 17
AF target mark ............................. p. 15
Camera shake warning
Aperture value .............................. p. 15
Shutter speed ............................... p. 15
Playback mode display
● Standard display
1
2 3 4
5 6
10
1
4/30
’10/02/26 12:30
00:12/00:34
17
Still image
6
Movie
● Advanced display
1
2 3 4
5 6
10
4/30
1/1000 F3.2
P
2.0
ISO WB
AUTO AUTO
NORM 14M
FILE 100 0004
’10/02/26 12:30
1
2
3
4
5
6
7
8
9
10
8
9 10 11
2.0
7 22 1/1000 F3.2
ISO WB
21
P
AUTO AUTO
20
19
NORM 14M
18
FILE 100 0004
12
13
14
15
16
’10/02/26 12:30
17
Battery check ......................... p. 12, 53
Print reservation/
number of prints .................. p. 50/p. 49
Protect .......................................... p. 39
Adding sound ......................... p. 32, 39
Current memory ........................... p. 59
Frame number/total number of images
(still images) ................................. p. 17
Elapsed time/total recording time
(movies) ....................................... p. 18
Histogram ..................................... p. 17
Shutter speed ............................... p. 15
Aperture value .............................. p. 15
ISO ............................................... p. 28
11
12
13
14
15
16
17
18
19
20
21
22
Exposure compensation............... p. 27
White balance .............................. p. 27
Compression (still images) ..... p. 30, 60
Image quality (movies) ........... p. 30, 61
Image size ........................ p. 30, 60, 61
Drive ............................................. p. 29
File number
Date and time ......................... p. 13, 43
Metering ....................................... p. 31
Shadow Adjustment Technology
................................................... p. 31
Flash ............................................ p. 26
Shooting mode ....................... p. 15, 21
Macro ........................................... p. 26
EN
9
Preparing the Camera
3
Inserting the battery
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
1
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
2
2
STYLUS-5010/μ-5010
1
1
2
2
1
1
Battery/card
compartment lock
Battery/card
compartment cover
Battery/card
compartment cover
2
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
STYLUS-9010/μ-9010, STYLUS-7040/
μ-7040: Insert the battery by putting in the
▼ marked side first, with the B marks
toward the battery lock knob.
STYLUS-5010/μ-5010: Insert the battery by
putting in the ▼ marked side first, with the
C marks toward the battery lock knob.
Damage to the battery exterior (scratches,
etc.) may produce heat or an explosion.
Insert the battery while sliding the battery
lock knob in the direction of the arrow.
Slide the battery lock knob in the direction
of the arrow to unlock, and then remove the
battery.
Turn off the camera before opening the
battery/card compartment cover.
When using the camera, be sure to close
the battery/card compartment cover.
Battery charge and camera
setup
STYLUS-7040/
μ-7040
Battery lock knob
Battery lock knob
Connect the camera to the computer to charge
the battery and setup the camera.
System requirements
Windows XP (SP2 or later)/
Windows Vista/Windows 7
STYLUS-5010/μ-5010
10
EN
When using another system other
than the above or no computer,
see “Charging the battery with the
included USB-AC adapter.” (p. 12)
1
Camera setup
Connect the camera to the
computer.
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
Set the camera date and time, time zone
and display language automatically; install
the camera instruction manual and PC
software (ib).
STYLUS-9010/
μ-9010
Do not insert SD/SDHC memory cards
before the camera setup.
Multi-connector
Do not format the internal memory until the
camera setup is complete. Doing so will
erase the camera instruction manual and
the PC software (ib) data that are stored on
the internal memory.
Indicator lamp
Check that your computer meets the
following system requirements:
Windows XP (SP2 or later)/
Windows Vista/Windows 7
Refer to the PC software (ib) help guide for
details on how to use the PC software (ib).
USB cable
(supplied)
2
Connector
cover
If nothing is displayed on the camera screen
even after connecting the camera to the
computer, the battery may be exhausted.
Leave the camera connected to the
computer until the battery has charged, then
disconnect and reconnect the camera.
Computer (on
and running)
Even if a computer has USB ports, proper
operation is not guaranteed in the following
cases:
Charging the battery
● Computers with USB ports installed using an
When the camera is connected to the
computer, the battery in the camera will be
charged.
expansion card, etc.
● Computers without a factory-installed OS and
home-built computers
● When charging, the indicator lamp light. When
charging is complete, the indicator lamp will turn
off.
If the indicator lamp does not light, the
camera may be incorrectly connected, or
the battery, camera, computer, or USB cable
may not be functioning correctly.
Select and execute “OLYMPUS
Camera Initialization”, which is
displayed on the computer screen
when the camera is recognized by
the computer.
Double-click the icon for the camera drive
(Removable Disk), and then execute
Setup. exe to start the camera setup.
3
Follow the instructions on the
computer screen and setup the
camera.
EN
11
Charging the battery with the
included USB-AC adapter
The included USB-AC adapter (F-2AC)
(hereafter referred as AC adapter) has
been designed to be used for charging
and playback. Make sure that shooting
is not being used while the AC adapter is
connected to the camera.
Example: AC adapter with an AC cable
1 STYLUS-7040/μ-7040
STYLUS-9010/
μ-9010
STYLUS-5010/μ-5010
The battery is not fully charged at
shipment. Before use, be sure to charge
the battery until the indicator lamp turns off
(STYLUS-9010/μ-9010: up to 3.5 hours,
STYLUS-7040/μ-7040, STYLUS-5010/
μ-5010: up to 3 hours).
If the indicator lamp does not light, the AC
adapter is not connected to the camera
correctly, or the battery, camera, or AC
adapter may be broken.
For details on the battery and the AC
adapter, see “Battery, USB-AC adapter
(included), Charger (sold separately)”
(p. 57).
Battery can be charged by connecting
the camera to the computer. However,
when charging with the system other than
Windows XP (SP2 or later)/Windows Vista/
Windows 7, charging takes much time.
Multi-connector
When to charge the batteries
Charge the battery when the error message
shown below appears.
Flashes in red
2
Connector
cover
BATTERY EMPTY
USB cable
(supplied)
4 14M
Monitor top left
Error message
When not using a computer
1
AC outlet
2
12
EN
See the next section under “Setting the date,
time and time zone.”
When using a computer with system
other than Windows XP (SP2 or later)/
Windows Vista/Windows 7
3
Indicator lamp
On: Charging
Off: Charged
The Instruction Manual PDF file can be
saved on a computer with the following
procedure.
Connect the camera to the computer and
copy the instruction manual PDF file for
your language in the “Manual” folder in the
internal memory of the camera.
Setting the date, time and
time zone
4
The date and time set here are saved to image
file names, date prints, and other data.
1
As in Steps 2 and 3, use FGHI
and the A button to set [M]
(month), [D] (day), [TIME] (hours
and minutes), and [Y/M/D] (date
order).
Press the n button to turn on
the camera.
For precise time setting, press the A button
as the time signal strikes 00 seconds.
● The date and time setting screen is displayed
To change the date and time, adjust the
setting from the menu. [X] (Date/time)
(p. 43)
when the date and time are not set.
X
Y
----
M D
TIME
. -- . --
-- : --
5
Y/M/D
Use HI to select the [x] time
zone and then press the A button.
● Use FG to turn daylight saving time ([SUMMER])
on or off.
’10.02.26 12:30
CANCEL MENU
Date and time setting screen
2
Use FG to select the year for [Y].
X
Y
Seoul
Tokyo
SUMMER
M D
TIME
2010 . -- . --
-- : --
Y/M/D
SET OK
The menus can be used to change the
selected time zone. [WORLD TIME] (p. 44)
CANCEL MENU
3
Press I to save the setting for [Y].
X
Y
M D
TIME
2010 . 00 . --
-- : --
Y/M/D
CANCEL MENU
EN
13
Changing the display language
The language for the menu and error messages
displayed on the monitor is adjustable.
1
1
STYLUS-9010/μ-9010
STYLUS-5010/μ-5010
Write-protect
switch
Contact area
Display the [SETUP] menu.
“Using the Menu” (p. 4)
2
2
INTERNAL/SD
MEMORY FORMAT
DATA REPAIR
AUTO
Insert the card straight until it clicks into
place.
COPY
ENGLISH
1
2
3
RESET
USB CONNECTION
EXIT MENU
4
5
Write-protect
switch
Use FG to select the r (Settings
1) tab and then press I.
1
3
STYLUS-7040/μ-7040
Do not touch the contact area directly.
PC
SET OK
Use FG to select [l] and press
the A button.
2
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
1
1
Use FGHI to select your
language and press the A button.
2
2
Press the m button.
“Number of storable pictures (still images)/
Continuous recording length (movies) in the
internal memory and SD/SDHC memory
cards” (p. 60)
Inserting the SD/SDHC
memory card (sold separately)
Always use SD/SDHC memory cards with
this camera. Do not insert other types of
memory card. “Using a SD/SDHC memory
card” (p. 58)
STYLUS-5010/μ-5010
To remove the SD/SDHC memory card
1
2
Although the camera can store images in
internal memory, SD/SDHC memory cards
(sold separately) can be also used to store
pictures.
Press the card in until it clicks and comes
out slightly, then remove the card.
14
EN
Shooting, Playback, and Erasing
2
Shooting with the optimum
aperture value and shutter
speed (P mode)
Hold the camera and compose the
shot.
In this mode, automatic shooting settings are
activated while also allowing changes to a wide
range of other shooting menu functions, such
as exposure compensation, white balance, etc.
as needed.
1
Monitor
Horizontal grip
Press the n button to turn on
the camera.
P mode indicator
P
Vertical grip
0.0
When holding the camera, take care not to
cover the flash with your fingers, etc.
WB
AUTO
ISO
AUTO
00:34
3
4 14M
Number of storable still pictures (p. 60)
Press the shutter button halfway
down to focus on the subject.
● When the camera focuses on the subject, the
Monitor
(standby mode screen)
If P mode is not displayed, press the m
button to display the function menu screen
and then set the shooting mode to P. “Using
the Menu” (p. 4)
exposure is locked (shutter speed and aperture
value are displayed), and the AF target mark
changes to green.
● The camera was unable to focus if the AF target
mark flashes red. Try focusing again.
AF target mark
Current shooting mode display
PROGRAM AUTO
P
P
0.0
Press halfway
WB
AUTO
ISO
AUTO
4 14M
Press the n button again to turn off
the camera.
1/400
Shutter speed
F3.2
Aperture value
“Focusing” (p. 54)
EN
15
4
To take the picture, gently press
the shutter button all the way down
while being careful not to shake the
camera.
2
Press the movie record button
again to stop recording.
Sound will also be recorded.
During sound recording, only the digital
zoom can be used. To record a movie with
optical zoom, set [R] (movies) (p. 32) to
[OFF].
P
Using the zoom
Press fully
1/400
F3.2
Pressing the zoom buttons adjusts the shooting
range.
Image review screen
Pressing the wide
(W) button
To view images during shooting
Pressing the q button enables playback of
images. To return to shooting, either press
the q button or press the shutter button
halfway down.
Zoom bar
P
Shooting movies
1
Continuous recording length
(p. 61)
P
0.0
0.0
WB
AUTO
ISO
AUTO
00:34
Press the movie record button to
start recording.
Pressing the telephoto
(T) button
WB
AUTO
ISO
AUTO
00:34
4 14M
4 14M
Model No.
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
Optical zoom
10×
7×
5×
Digital zoom
5×
5×
5×
To take larger images without reducing
image quality
[FINE ZOOM] (p. 32)
REC
00:34
00:12
Recording time
Lights up red when recording
The effects of the set shooting mode can
be used when shooting movies (when
P mode, p mode or Q mode is
set, shooting is performed with the P mode
setting).
To take larger images
[DIGITAL ZOOM] (p. 32)
The zoom bar appearance identifies the
status of the fine zoom/digital zoom.
When using
optical zoom
Optical zoom range
When using
fine zoom
Fine zoom
range
When using
digital zoom
Digital zoom
range
16
EN
Changing the shooting
information display
The display of the screen information can
be changed to best match the situation, for
example, the need for a clear view of the screen
or for making a precise composition by using the
grid display.
1
Viewing images
1
Press the q button.
Number of frames/
Total number of images
4/30
Press F (INFO).
● The displayed shooting information changes in
the order shown below each time the button is
pressed. “Shooting mode display” (p. 8)
Normal
’10/02/26 12:30
P
Playback image
0.0
WB
AUTO
ISO
AUTO
No information
00:34
4 14M
2
Turn the wheel controller to select
an image.
● It can be performed by pressing HI.
Detailed
P
0.0
Displays
previous
image
Displays
next image
WB
AUTO
ISO
AUTO
00:34
4 14M NORM
Reading a histogram
If the peak fills too much of the frame,
the image will appear mostly white.
If the peak fills too
much of the frame,
the image will
appear mostly black.
The green section shows
luminance distribution
within the screen’s center.
Keep turning the wheel controller to fast
forward or reverse. It can be performed by
holding HI.
The display size of the images can be
changed. “Index view, close-up view, and
event index” (p. 19)
To play sound recordings
To play sound recorded with an image,
select the image and press the A button. A
! icon appears on images with which sound
has been recorded.
[R] (still images) (p. 32, 39)
During audio playback
EN
17
To play back movies
Operations while playback is paused
Select a movie, and press the A button.
4/30
00:14/00:34
MOVIE PLAY OK
During pause
’10/02/26 12:30
Movie
Cueing
Operations during movie playback
Use F to display the first
frame and press G to display
the last frame.
Turn the wheel controller to
Advancing
advance or rewind by one
and rewinding
frame at a time. Keep turning
one frame at a
the wheel controller for
time*1
continuous advance or rewind.
Resuming
playback
Elapsed time/
Total recording
time
Press the A button to resume
playback.
00:12/00:34
To operate with HI
During playback
*1
Pausing and
restarting
playback
Press the A button to pause
playback. During pause, fast
forward or reverse, press the
A button to restart playback.
Fast forward
Press I to fast forward. Press
I again to increase the fast
forward speed.
Rewind
Press H to rewind. The speed
at which the recording rewinds
increases each time H is
pressed.
Turn the wheel controller
Adjusting the
or use FG to adjust the
volume
volume.
Press I or H to advance or rewind one frame
at a time. Hold I or H pressed for continuous
advance or rewind.
To stop movie playback
Press the m button.
Erasing images during
playback (Single image erase)
1
Display the image you want to erase
and press G (D).
ERASE
ALL ERASE
SEL. IMAGE
ERASE
CANCEL
BACK MENU
2
SET OK
Press FG to select [ERASE], and
press the A button.
[ALL ERASE] (p. 39) and [SEL. IMAGE]
(p. 38) can be used to erase multiple images
at the same time.
18
EN
Index view, close-up view, and
event index
To select an image in index view
Use FGHI to select an image, and press
the A button to display the selected image
in single-image view.
Index view enables quick selection of a desired
image. Close-up view (up to 10x magnification)
allows checking of image details. In event
index*1, images are grouped by the shooting
dates and representative images for an event
can be displayed.
*1
To scroll an image in close-up view
Use FGHI to move the viewing area.
To select an image in event index
Pictures with different dates can be grouped into the
same event using the PC software (ib).
1
Use HI to select the representative image
and press the A button. The images in the
selected event are played back.
Press the zoom buttons.
Single-image view
4/30
Changing the image
information display
Close-up view
W
4/30
Shooting information settings displayed on the
screen can be changed.
1
Press F (INFO).
● The displayed image information changes in
’10/02/26 12:30
W
T
T
’10/02/26 12:30
the order shown below each time the button is
pressed.
Normal
10
Index view
4/30
’10/02/26
No information
2
’10/02/26 12:30
4
Detailed
W
T
10
4/30
’10/02/26
1/1000 F3.2
2
4
P
2.0
ISO WB
AUTO AUTO
NORM 14M
FILE 100 0004
’10/02/26 12:30
“Reading a histogram” (p. 17)
W
T
Event index
’10/02/26
EN
19
Playing back panorama
images
Using the menu guide
Panorama images that were combined together
using [AUTO] or [MANUAL] can be scrolled for
viewing.
If the E button is pressed while settings are
being adjusted in the playback function or
[SETUP] menus, a description of the selected
option is displayed.
“Using the Menu” (p. 4)
“Creating panoramic images (p mode)”
(p. 23)
1
Using the camera guide
Select a panorama image during
playback.
Use the camera guide to look up camera
operations.
“Viewing images” (p. 17)
4/30
1
Press the E button in the standby
mode screen or the playback
screen.
IN-CAMERA MANUAL
REPLAY OK
2
Search
Learn about the camera
History
Message
’10/02/26 12:30
Press the A button.
EXIT
Submenu 2
Current viewing area
To control panorama image playback
Zoom in/Zoom out: Press the A button to
pause playback. Then press the zoom button
to enlarge/shrink the image.
Playback direction: Press FGHI to
pause playback and scroll the image in the
direction of the pressed button.
Pause: Press the A button.
Restart scrolling: Press the A button.
Stop playback: Press the m button.
SET OK
Application
Search
Functions or operating methods
can be searched from a term or
shooting objective.
Learn about the
camera
Information is shown about
recommended functions and basic
operating methods for the camera.
History
Searches can be performed from
the search history.
Message
Messages from the camera can
be viewed.
2
Use FG to select the desired item.
IN-CAMERA MANUAL
Search
Learn about the camera
History
Message
EXIT
SET OK
● Follow the on-screen instructions to search the
desired contents.
20
EN
Using Shooting Modes
To change the shooting mode
The shooting mode (P, M, s, P,
p, Q) can be changed with using the
function menu.
“Using the Menu” (p. 4)
Using the best mode for the
shooting scene (s mode)
1
SCENE MODE
Shooting with automatic
settings (M mode)
The camera will automatically select the optimal
shooting mode for the scene. This is a fully
automatic mode that allows you to take a picture
suited to the scene by simply pressing the
shutter button. In M mode, settings in the
shooting menu can be selected, but the changed
setting is not reflected in the actual shot.
1
Set the shooting mode to s.
0.0
WB
AUTO
4 14M
2
Press G to go to the submenu.
Set the shooting mode to M.
PORTRAIT
The icon changes depending on the scene
that the camera automatically selects.
0.0
WB
AUTO
4 14M
3
00:34
Use HI to select the mode and
then press the A button to set.
4 14M NORM
In some cases, the camera may not select
the desired shooting mode.
When the camera cannot identify the
optimal mode, P mode will be selected.
0.0
00:34
WB
AUTO
4 14M
Icon indicating the scene mode
that is set
EN
21
In s modes, the optimum shooting
settings are pre-programmed for specific
shooting scenes. For this reason, settings
may not be changed in some modes.
Option
B PORTRAIT/F LANDSCAPE/
G NIGHT SCENE*1/
M NIGHT+PORTRAIT/
C SPORT/N INDOOR/
W CANDLE/
R SELF PORTRAIT/
S SUNSET*1/X FIREWORKS*1/
V CUISINE/d DOCUMENTS/
q BEACH & SNOW/ PET
*1
Application
Shooting with special effects
(P mode)
To add expression to your photo, select the
desired special effect.
1
Set the shooting mode to P.
The camera
takes a picture
using the
optimum settings
for the scene
conditions.
When the subject is dark, noise reduction is
automatically activated. This approximately doubles
the shooting time during which no other pictures can
be taken.
MAGIC FILTER
0.0
WB
AUTO
4 14M
2
Press G to go to the submenu.
To take pictures of a moving subject
like a pet ([ PET] mode)
POP ART
1 Use HI to select [ PET], and press
the A button to set.
2 Hold the camera to align the AF target
mark on the subject and press the A
button.
0.0
WB
AUTO
● When the camera recognizes the subject,
the AF target mark automatically tracks the
subject movement to focus on it continuously.
“To focus on a moving subject continuously
(AF Tracking)” (p. 31).
3
Use HI to select the desired effect
and then press the A button to set.
0.0
WB
AUTO
00:34
4 14M
Icon indicating P mode that
is set
Shooting mode
MAGIC FILTER
Option
[ POP ART
\ PIN HOLE
] FISH EYE
@ DRAWING
In P mode, the optimum shooting
settings are pre-programmed for each
scene effect. For this reason, some settings
cannot be changed in some modes.
22
EN
Creating panoramic images
(p mode)
1
Taking pictures with [AUTO]
1 Press the shutter button to take the first
frame.
2 Move the camera slightly in the direction
of the second frame.
Set the shooting mode to p.
PANORAMA
AUTO
AUTO
Target mark
0.0
WB
AUTO
2
Press G to go to the submenu.
3
Use HI to select the desired mode
and then press the A button to set.
Submenu 1
Pointer
CANCEL MENU
4 14M
Application
AUTO
Three frames are taken and
combined by the camera. The
user only composes the shots
so that the target marks and
pointers overlap, and the camera
automatically releases the shutter.
MANUAL
Three frames are taken and
combined by the camera. The
user composes the shots using
the guide frame and manually
releases the shutter.
PC
The frames that were taken are
combined into a panorama image
using the PC software (ib).
SAVE OK
Screen when combining images
from left to right
3 Move the camera slowly while keeping it
straight, and stop the camera where the
pointer and target mark overlap.
● The camera releases the shutter
automatically.
AUTO
CANCEL MENU
SAVE OK
To combine only two pictures, press the
A button before taking a third frame.
4 Repeat Step 3 to take a third frame.
For details on installing the PC software
(ib), see “Battery charge and camera setup”
(p. 10).
● After the third frame is taken, the camera
When set to [AUTO] or [MANUAL], [IMAGE
SIZE] (p. 30) is fixed to [2].
To exit the panorama function without
saving an image, press the m button.
The focus, exposure (p. 27), zoom position
(p. 16), and white balance (p. 27) are locked
at the first frame.
If the shutter does not automatically release,
try [MANUAL] or [PC].
automatically processes the frames and the
combined panorama image is displayed.
The flash (p. 26) is fixed to $ (FLASH OFF)
mode.
EN
23
Taking pictures with [MANUAL]
Taking pictures with [PC]
1 Use HI to specify at which edge the
next picture is to be connected.
1 Use FGHI to select the direction that
the frames are combined.
MANUAL
Direction for
combining the
next frame
1
2
2 Press the shutter button to take the first
frame, and then compose the second
shot.
Before first
shot
BACK MENU
PC
1
2 Press the shutter button to take the first
frame.
2
BACK MENU
Joint areas
MANUAL
1
MANUAL
2
1
BACK MENU
CANCEL MENU
2
1
3 Compose the next shot so that joint area
1 overlaps joint area 2.
MANUAL
1
CANCEL MENU
2
SAVE OK
Composition of the 2nd frame
4 Press the shutter button to take the next
shot.
To combine only two pictures, press the
A button before taking the third frame.
5 Repeat steps 3 and 4 to take a third
frame.
● After the third frame is taken, the camera
automatically processes the frames and the
combined panorama image is displayed.
To exit the panorama function without
saving an image, press the m button.
EN
PC
SAVE OK
1st frame
24
After first
shot
2
EXIT MENU
● After the first shot, the area shown in white
reappears on the side of the display opposite
the pan direction. Frame subsequent
photographs so that they overlap with the
image in the monitor.
3 Repeat Step 2 until the number of
desired frames is taken, and then press
the A button or m button when
finished.
Panorama shooting is possible for up to
10 frames.
Refer to the PC software (ib) help guide for
details on how to make panorama images.
Smoothing out skin tone and
texture (Q mode)
The camera identifies a person’s face and gives
the skin a smooth, translucent look for taking
the picture.
1
Set the shooting mode to Q.
P
BEAUTY
0.0
WB
AUTO
4 14M
2
Point the camera toward the
subject. Check the frame appearing
around the face detected by the
camera, and then press the shutter
button to take the picture.
● The unedited image and edited image are both
saved.
● If the image cannot be retouched, only the
unedited image is saved.
The frame may not appear or may take
some time to appear for some subjects. In
addition, this function may have no visible
effect on some subjects.
The [IMAGE SIZE] of the retouched image
is limited to [n] or lower.
EN
25
Using Shooting Functions
Shooting closeups
(Macro shooting)
“Using the Menu” (p. 4)
Using the flash
This function enables the camera to focus and
shoot subjects at close distances.
The flash functions can be selected to best
match the shooting conditions.
1
1
Select the flash option in the
shooting function menu.
Select the macro option in the
shooting function menu.
P
P
FLASH AUTO
OFF
0.0
WB
AUTO
ISO
AUTO
0.0
WB
AUTO
ISO
AUTO
4 14M
2
26
EN
2
Use HI to select the setting
option, and press the A button to
set.
Option
4 14M
Description
FLASH AUTO
The flash fires automatically in
low-light or backlight conditions.
REDEYE
Pre-flashes are emitted to reduce
the occurrence of red eye in your
photos.
FILL IN
The flash fires regardless of the
available light.
FLASH OFF
The flash does not fire.
Use HI to select the setting
option, and press the A button to
set.
Option
Application
Description
Macro mode is
deactivated.
OFF
―
When the zoom is at the widest (W) position, this function enables
shooting as close as the following distances.
MACRO
This enables the
camera to shoot
subjects at close
distances.
STYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
10 cm (3.9 in.)
10 cm (3.9 in.)
15 cm (5.9 in.)
When the zoom is at the most telephoto (T) position, this function
enables shooting as close as the following distances.
STYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
90 cm (35.4 in.)
60 cm (23.6 in.)
60 cm (23.6 in.)
This function enables shooting as close as the following distances.
STYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
SUPER MACRO*1
This enables the
camera to shoot
subjects at even
closer distances.
1 cm (0.4 in.)
2 cm (0.8 in.)
7 cm (2.8 in.)
Subjects at the following or farther distances cannot be brought into
focus.
STYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
50 cm (19.7 in.)
*1
70 cm (27.6 in.)
60 cm (23.6 in.)
The zoom is automatically fixed.
The flash (p. 26) and zoom (p. 16) cannot be set when [a SUPER MACRO] (p. 26) is selected.
Using the self-timer
Option
Description
After the shutter button is pressed all the way
down, the picture is taken after a short delay.
Y OFF
The self-timer is deactivated.
1
Y 12 SEC
The self-timer lamp turns on for
approx. 10 seconds, then blinks
for approx. 2 seconds, and then
the picture is taken.
Y 2 SEC
The self-timer lamp blinks for
approx. 2 seconds, then the
picture is taken.
Select the self-timer option in the
shooting function menu.
P
OFF
2
12
0.0
WB
AUTO
ISO
AUTO
4 14M
2
Self-timer shooting is automatically canceled
after one shot.
To cancel the self-timer after it starts
Press the m button.
Use HI to select the setting
option, and press the A button to
set.
EN
27
2
Adjusting the brightness
(Exposure compensation)
The standard brightness (appropriate exposure)
set by the camera based on the shooting mode
(except for M) can be adjusted brighter or
darker to obtain a desired shot.
1
Select the exposure compensation
option in the shooting function
menu.
P
0.0
0.3 0.0 0.3
WB
AUTO
ISO
AUTO
2
Use HI to select the desired
brightness, and press the A button.
Adjusting to a natural color
scheme (White balance)
Select the white balance option in
the shooting function menu.
P
WB AUTO
0.0
WB
AUTO
28
EN
Option
Description
WB AUTO
The camera automatically adjusts
the white balance according to the
shooting scene.
5
For shooting outdoors under a
clear sky.
3
For shooting outdoors under a
cloudy sky.
1
For shooting under tungsten
lighting.
w
For shooting under daylight
fluorescent lighting (household
lighting, etc.)
x
For shooting under neutral
fluorescent lighting (desk lamps,
etc.)
y
For shooting under white
fluorescent lighting (offices, etc.)
Selecting the ISO sensitivity
Abbreviation for the International
Organization for Standardization. ISO
standards specify the sensitivity for digital
cameras and film, thus codes such as “ISO
100” are used to represent sensitivity.
For more natural coloring, choose a white
balance option suited to the scene.
1
Use HI to select the setting
option, and press the A button to
set.
ISO
AUTO
In the ISO setting, although smaller values
result in less sensitivity, sharp images can
be taken under fully lit conditions. Larger
values result in higher sensitivity, and
images can be taken at fast shutter speeds
even under low light conditions. However,
high sensitivity introduces noise into the
resulting picture, which may give it a grainy
appearance.
1
Select the ISO setting option in the
shooting function menu.
P
Sequential shooting (Drive)
Pictures are taken sequentially while the shutter
button is held down.
1
Select the drive option in the
shooting function menu.
0.0
ISO 200
1/400
ISO
100
ISO
200
P
WB
AUTO
ISO
400
F3.2
0.0
2
WB
AUTO
ISO
AUTO
Use HI to select the setting
option, and press the A button to
set.
Option
ISO AUTO
Option
Description
The camera automatically adjusts
the sensitivity according to the
shooting scene.
The camera uses a higher
sensitivity compared to
HIGH ISO AUTO [ISO AUTO] to minimize blur
caused by a moving subject or by
camera shake.
Value
SEQUENTIAL
The ISO sensitivity is fixed to the
selected value.
Description
o
One frame is shot each time the
shutter button is pressed.
j*1
Take sequential shots using the
focus, brightness (exposure) and
white balance set in the first frame.
c
The camera takes sequential shots
at a faster speed than in [j].
d
The camera takes sequential shots
at approximately 10 frames/sec*2.
*1
*2
The shooting speed varies depending on the
settings for [IMAGE SIZE/COMPRESSION] (p. 30).
approximately 14 frames/
sec.
approximately 10 frames/
STYLUS-5010/μ-5010
sec.
STYLUS-7040/μ-7040
When set to [j], the flash (p.26) cannot
be set to [REDEYE]. In addition, when
set to [c] or [d], the flash is fixed to
[FLASH OFF].
When set to [c] or [d], [IMAGE SIZE]
is limited to [3] or lower, and the ISO
sensitivity is fixed to [ISO AUTO].
EN
29
Menus for Shooting Functions
The default settings of the function are highlighted in
.
Selecting the image quality for still images [IMAGE SIZE/COMPRESSION]
I (Shooting menu 1) X IMAGE SIZE/COMPRESSION
Available shooting modes: P M s P p Q
Submenu 1
IMAGE SIZE
COMPRESSION
Submenu 2
Application
14M (4288×3216)
Suitable for printing pictures over A3 (11×17 in.).
8M (3264×2448)
Suitable for printing pictures up to A3 (11×17 in.).
5M (2560×1920)
Suitable for printing pictures at A4 (8.5×11 in.).
3M (2048×1536)
Suitable for printing pictures up to A4 size (8.5×11 in.).
2M (1600×1200)
Suitable for printing pictures at A5 (5×7 in.).
1M (1280×960)
Suitable for printing pictures at postcard size.
VGA (640×480)
Suitable for viewing pictures on a TV or using pictures on emails and
web sites.
16:9G (4288×2416)
Suitable for playing pictures on a widescreen TV and for printing on A3
or 11"×17".
16:9F (1920×1080)
Suitable for playing pictures on a widescreen TV and for printing on A5
or 5"×7".
FINE
Shooting at high quality.
NORMAL
Shooting at normal quality.
“Number of storable pictures (still images)/Continuous recording length (movies) in the internal
memory and SD/SDHC memory cards” (p. 60)
Selecting the image quality for movies [IMAGE SIZE/IMAGE QUALITY]
A (Movie menu) X IMAGE SIZE/IMAGE QUALITY
Available shooting modes: P M s P p Q
Submenu 1
IMAGE SIZE
Submenu 2
720P
VGA (640×480)
QVGA (320×240)
IMAGE QUALITY FINE/NORMAL
Application
Select the image quality based on the image size and frame rate.
Select [FINE] to shoot with higher image quality.
“Number of storable pictures (still images)/Continuous recording length (movies) in the internal
memory and SD/SDHC memory cards” (p. 60)
When [IMAGE SIZE] is set to [QVGA], [IMAGE QUALITY] is fixed to [FINE].
30
EN
For information on using the menus, see “Using the Menu” (p. 4).
Brightening the subject against
backlight [SHADOW ADJUST]
I (Shooting menu 1) X SHADOW ADJUST
Available shooting modes: P M s P p
Q
Submenu 2
Application
AUTO
The shadow adjustment effect is
applied when shooting against
backlight.
OFF
The effect is not applied.
ON
Shoot with automatic adjustment
to brighten an area that has
become darker.
To focus on a moving subject
continuously (AF Tracking)
1 Hold the camera to align the AF target
mark on the subject and press the
A button.
2 When the camera recognizes the subject,
the AF target mark automatically tracks
the subject movement to focus on it
continuously.
3 To cancel the tracking, press the
A button.
Depending on the subjects or the shooting
conditions, the camera may be unable to
lock the focus or fail to track the subject
movement.
When set to [ON], [ESP/n] (p. 31) is
automatically fixed to [ESP].
When the camera fails to track the subject
movement, the AF target mark changes to
red.
Selecting the focusing area [AF MODE]
I (Shooting menu 1) X AF MODE
Available shooting modes: P M s P p
Q
Submenu 2
FACE/iESP*1
Application
The camera focuses automatically.
(If a face is detected, it is shown
by a white frame*1; when the
shutter button is pressed halfway
and the camera focuses, the
frame turns to green*2. If no face is
detected, the camera chooses a
subject in the frame and focuses
automatically.)
SPOT
The camera focuses on the
subject located within the AF
target mark.
AF TRACKING
The camera tracks the subject
movement automatically to focus
on it continuously.
*1
*2
For some subjects, the frame may not appear or
may take some time to appear.
If the frame blinks in red, the camera cannot focus.
Try refocusing on the subject.
Selecting the method for measuring
the brightness [ESP/n]
I (Shooting menu 1) X ESP/n
Available shooting modes: P M s P p
Q
Submenu 2
Application
ESP
Shoots to obtain a balanced
brightness over the entire screen
(Meters the brightness at the
center and surrounding areas of
the screen separately).
5 (spot)
Shoots the subject at the center
during backlighting (Meters the
brightness at the center of the
screen).
When set to [ESP], the center may
appear dark when shooting against strong
backlighting.
EN
31
Shooting at higher magnifications than
optical zoom without reducing the
image quality [FINE ZOOM]
I (Shooting menu 1) X FINE ZOOM
Available shooting modes: P M s P p
Q
Submenu 2
Application
OFF
Optical zoom is used to zoom in
for shooting.
ON
Optical zoom and image cropping
are combined to zoom in for
shooting.*1
*1
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
Recording sound when shooting still
images [R]
J (Shooting menu 2) X R
Available shooting modes: P M s P p
Q
Submenu 2
No sound is recorded.
ON
The camera automatically starts
recording sound for approx.
4 seconds after a picture is taken.
This is useful for recording notes
or comments about the picture.
When recording, aim the microphone (p. 6) at
the source of the sound you want to record.
Approx. 67× (max.)
Approx. 47× (max.)
Approx. 33.5× (max.)
This function will not reduce the image
quality since it dose not convert the data with
fewer pixels into the data with larger pixels.
When set to [ON], [IMAGE SIZE] is limited
to [4] or lower.
The setting is not available when
[DIGITAL ZOOM] is set to [ON].
[FINE ZOOM] is not available when
[a SUPER MACRO] (p. 26) is selected.
Recording sound when shooting
movies [R]
A (Movie menu) X R
Available shooting modes: P M s P p
Q
Submenu 2
No sound is recorded.
ON
Sound is recorded.
When set to [ON], only the digital zoom can
be used during movie recording. To record
the movie with the optical zoom, set [R]
(movies) to [OFF].
I (Shooting menu 1) X DIGITAL ZOOM
Submenu 2
Application
OFF
Only optical zoom is used to zoom
in for shooting.
ON
Optical zoom and digital zoom
are combined to zoom in for
shooting.*1
*1
STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
Approx. 50× (max.)
Approx. 35× (max.)
Approx. 25× (max.)
The setting is not available when [FINE
ZOOM] is set to [ON].
[DIGITAL ZOOM] is not available when
[a SUPER MACRO] (p. 26) is selected.
32
EN
Application
OFF
Shooting at higher magnifications than
optical zoom [DIGITAL ZOOM]
Available shooting modes: P M s P p
Q
Application
OFF
Reducing the blur caused by the
camera shake when shooting
[IMAGE STABILIZER] (still images)/
[IS MOVIE MODE] (movies)
I (Shooting menu 1) X
IMAGE STABILIZER (still images)/
A (Movie menu) X
IS MOVIE MODE (movies)
Available shooting modes: P M s P p
Q
Submenu 2
Application
OFF
The image stabilizer is
deactivated. This is recommended
for shooting when the camera is
fixed in place on a tripod or other
stable surface.
ON
The image stabilizer is activated.
For information on using the menus, see “Using the Menu” (p. 4).
The camera’s default settings are [IMAGE
STABILIZER] (still images) to [ON] and [IS
MOVIE MODE] (movies) to [OFF].
There may be a noise coming from inside
the camera when the shutter button is
pressed with [IMAGE STABILIZER] (still
images) set to [ON].
Automatically rotating images shot
with the camera in a vertical position
during playback [PIC ORIENTATION]
J (Shooting menu 2) X PIC ORIENTATION
Available shooting modes: P M s P p
Q
Images may not be stabilized if camera
shake is too severe.
During shooting, the [y] (p. 39) setting on
the playback menu is set automatically.
When the shutter speed is extremely slow,
such as when taking pictures at night,
[IMAGE STABILIZER] (still images) may not
be as effective.
When shooting while the [IS MOVIE MODE]
(movies) is set to [ON], the image will be
enlarged somewhat before saving.
Viewing the image immediately after
shooting [REC VIEW]
This function may not work properly if
the camera is facing up or down during
shooting.
Submenu 2
OFF
ON
Information about the vertical/
horizontal orientation of the
camera during shooting is
recorded with images. Images
are automatically rotated during
playback.
J (Shooting menu 2) X REC VIEW
Available shooting modes: P M s P p
Q
Submenu 2
Application
OFF
The image being recorded is not
displayed. This allows the user
to prepare for the next shot while
following the subject in the monitor
after shooting.
ON
The image being recorded is
displayed. This allows the user to
make a brief check of the image
that was just taken.
Application
Information about the vertical/
horizontal orientation of the
camera during shooting is not
recorded with images. Images
shot with the camera in a vertical
position are not rotated during
playback.
Displaying icon guides [ICON GUIDE]
J (Shooting menu 2) X ICON GUIDE
Available shooting modes: P M s P p
Q
Submenu 2
Application
OFF
No icon guide is displayed.
ON
The explanation of the selected
icon will be displayed when
a shooting mode or shooting
function menu icon is selected
(position the cursor on the icon for
a while to display the explanation).
PROGRAM AUTO
Icon guide
P
Functions can be changed
manually.
0.0
WB
AUTO
ISO
AUTO
4 14M
EN
33
Menus for Playback, Editing, and
Printing Functions
The default settings of the function are highlighted in
.
Data must have been created with the PC software (ib) before using some function.
Refer to the PC software (ib) help guide for details on how to use the PC software (ib).
For details on installing the PC software (ib), see “Battery charge and camera setup” (p. 10).
Playing back pictures automatically
[SLIDESHOW]
SLIDESHOW
Submenu 1
SLIDE
BGM
TYPE
START
Searching for images and playing back
the related images [PHOTO SURFING]
PHOTO SURFING
Submenu 2
Application
Selects the content
ALL/EVENT/
to be included in the
COLLECTION
slideshow.
OFF/Cosmic/
Breeze/
Selects the
Mellow/
background music
Dreamy/
options.
Urban
Selects the type of
STANDARD/
transition effect used
FADE/ZOOM
between slides.
―
Starts the slideshow.
Single-frame advance/rewind:
In [PHOTO SURFING], images can be
searched and related images can be played
back by selecting the related items.
To start [PHOTO SURFING]
Press the A button to start
[PHOTO SURFING].
When a related item of the image displayed
is selected with FG, images related to the
item are displayed in the lower part of the
monitor. Use HI to display an image.
To select the related items undisplayed,
press the A button when selecting an item.
To stop [PHOTO SURFING], press the
m button, or select [BACK] and press
the A button.
During a slideshow, press I to skip ahead
one frame or press H to go back one frame.
BACK
2010/
02/26
Related items
35ºN
139ºE
Images corresponding the
related items
34
EN
For information on using the menus, see “Using the Menu” (p. 4).
Viewing images by event [EVENT q]
EVENT q
In [EVENT q], images in an event are
played back. (Images with the same
shooting date are grouped into the same
event.)
To start [EVENT q]
To start [COLLECTION q]
Press the A button, and then use
FGHI to select the desired collection.
Press the A button again to start playback
of the selected collection. Use HI to
advance or rewind by one frame.
To stop [COLLECTION q], press the
m button.
Press the A button to start [EVENT q].
(The event, including the image for which
single-image view was being performed
when the playback function menu was
selected, is played back.)
Use HI to advance or rewind by one
frame.
To stop [EVENT q], press the
m button.
4/30
COLLECTION
BACK MENU
SET OK
Using a PC software (ib) and importing
data back to the camera
The following functions can be performed
when data created with the PC software (ib)
is imported back to the camera.
EXIT MENU
PLAY OK
’10/02/26 12:30
Refer to the PC software (ib) help guide for
details on how to use the PC software (ib).
[PHOTO SURFING]
Playing back images by Collection
created with the PC software (ib)
[COLLECTION q]
COLLECTION q
In [COLLECTION q], the collection is
played back that has been created with the
PC software (ib) and imported back from a
computer.
Information of persons or shooting locations
and new Collections can be added in the
related items.
[EVENT q]
Images can be played back by event created
with the PC software (ib).
Event index (p. 19)
The representative images for an event
created with the PC software (ib) can be
displayed.
EN
35
Retouching the skin and eyes
[BEAUTY FIX]
Changing the image size [Q]
EDIT X Q
BEAUTY FIX
Depending on the picture, the editing may
not be effective.
Submenu 1
Submenu 2
―
ALL
CLEAR SKIN
SOFT/AVG/
HARD
SPARKLE EYE
―
DRAMATIC
EYE
―
Application
[CLEAR SKIN],
[SPARKLE EYE] and
[DRAMATIC EYE] are
applied together.
Makes skin look
smooth and
translucent. Select the
correction effect from
3 levels.
Enhances the contrast
of the eyes.
Enlarges the subject’s
eyes.
1 Use FG to select a correction item, and
press the A button.
2 Use HI to select an image for
retouching, and press the A button.
Submenu 2
C 640 × 480
E 320 × 240
Application
This saves a high-resolution image
as a separate image with a smaller
size for use in e-mail attachments
and other applications.
1 Use HI to select an image.
2 Use FG to select an image size and
press the A button.
● The resized image is saved as a separate
image.
Cropping image [P]
EDIT X P
1 Use HI to select an image, and press
the A button.
2 Use the zoom buttons to select the size of
the cropping frame, and use FGHI to
move the frame.
● The retouched image is saved as a separate
image.
When [CLEAR SKIN] is selected
Use FG to select the retouching level, and
press the A button.
Cropping frame
SET OK
CLEAR SKIN
SOFT
AVG
HARD
BACK MENU
36
EN
SET OK
3 Press the A button after you have
selected the area to trim.
● The edited image is saved as a separate
image.
For information on using the menus, see “Using the Menu” (p. 4).
Changing the color tone of image
[COLOR EDIT]
1 Use HI to select an image, and press
the A button.
2 Use HI to select a calendar. Use FG
to select the image orientation, and then
press the A button.
EDIT X COLOR EDIT
Submenu 2
Application
BLACK & WHITE
This changes the image to black
and white.
3 Use FG to select the Year of the
calendar, and press I.
SEPIA
This changes the image to a
sepia tone.
4 Use FG to select the Month of the
calendar, and press the A button.
HIGH
SATURATION
This increases the color saturation
of the image.
LOW
SATURATION
This slightly increases the color
saturation of the image.
COLOR EDIT
SEPIA
● The edited image is saved as a separate
image.
Brightening areas that are dark
due to backlight or other reasons
[SHADOW ADJ]
EDIT X SHADOW ADJ
1 Use HI to select an image, and press
the A button.
● The edited image is saved as a separate
EXIT MENU
SET OK
1 Use HI to select an image, and press
the A button.
2 Use HI to select the desired color, and
press the A button.
● The image with the selected color is saved as
a separate image.
image.
Depending on the picture, the editing may
not be effective.
The retouching process may lower the
image resolution.
Retouching red eyes in flash shooting
[REDEYE FIX]
EDIT X REDEYE FIX
Adding a calendar to an image
[CALENDAR]
1 Use HI to select an image, and press
the A button.
EDIT X CALENDAR
● The edited image is saved as a separate
image.
CALENDAR
Depending on the picture, the editing may
not be effective.
The retouching process may lower the
image resolution.
SET OK
EN
37
Erasing images [ERASE]
To erase all images [ALL ERASE]
ERASE
Submenu 1
Application
ALL ERASE
All images in the internal memory
or card will be erased.
SEL. IMAGE
Images are individually selected
and erased.
ERASE/
Deletes the image displayed.
ERASE EVENT*1
CANCEL
*1
Cancels deletion of the image.
If G is pressed when an event is played back, all
images in the event are erased.
When erasing pictures in the internal
memory, do not insert the card into the
camera. Or set [INTERNAL/SD] to [IN].
Before erasing pictures from a memory
card, insert the card into the camera and
select [AUTO] for [INTERNAL/SD].
“Selecting a storage device [INTERNAL/
SD]” (p. 40)
Protected images cannot be erased.
To individually select and erase
images [SEL. IMAGE]
1 Use FG to select [SEL. IMAGE], and
press the A button.
2 Use HI to select the image to be
erased, and press the A button to add a
R mark to the image.
● Press the W zoom button to display an index
view. Images can be quickly selected using
the FGHI buttons. Press the T button to
return to the single frame display.
1 Use FG to select [ALL ERASE], and
press the A button.
2 Use FG to select [YES], and press the
A button.
Saving print settings to the image data
[PRINT ORDER]
q (Playback menu) X PRINT ORDER
“Print reservations (DPOF)” (p. 50)
Print reservation can be set only for still
images that are recorded to the card. Set
[INTERNAL/SD] to [AUTO].
Protecting images [0]
q (Playback menu) X 0
Protected images cannot be erased by
[ERASE] (p. 18, 38), [ERASE EVENT]
(p. 38), [SEL. IMAGE] (p. 38), or
[ALL ERASE] (p. 38), but all images are
erased by [MEMORY FORMAT]/[FORMAT]
(p. 40).
1 Use HI to select an image.
2 Press the A button.
● Press the A button again to cancel the
settings.
3 If necessary, repeat Steps 1 and 2
to protect other images, and press the
m button.
Rotating images [y]
q (Playback menu) X y
SEL. IMAGE
1 Use HI to select an image.
2 Press the A button to rotate the image.
R mark
3 If necessary, repeat Steps 1 and 2 to
make settings for other images, and press
the m button.
OK
ERASE/CANCEL MENU
3 Repeat Step 2 to select the images to be
erased, and then press the m button
to erase the selected images.
4 Use FG to select [YES], and press the
A button.
● The images with a R mark are erased.
38
EN
The new picture orientations will be saved
even after the power is turned off.
For information on using the menus, see “Using the Menu” (p. 4).
Adding sound to still images [R]
q (Playback menu) X R
1 Use HI to select an image.
2 Aim the microphone toward the sound
source.
Microphone
3 Press the A button.
● Recording starts.
● The camera adds (records) sound for approx.
4 seconds while playing back the image.
EN
39
Menus for Other Camera Settings
The default settings of the function are highlighted in
Selecting a storage device
[INTERNAL/SD]
r (Settings 1) X INTERNAL/SD
Submenu 2
Application
AUTO
If a card is inserted, the card is
automatically selected. If no card
is inserted, internal memory is
used.
IN*1
Internal memory is selected.
*1
Internal memory is used even if a card is inserted.
Erasing data completely
[MEMORY FORMAT]/[FORMAT]
r (Settings 1) X MEMORY FORMAT/
FORMAT
Before formatting, check that no important
data is left in the internal memory or card.
If the internal memory is formatted, the
camera instruction manual and the PC
software (ib) data that are stored on the
internal memory are erased. If necessary,
store the backup before formatting.
Cards must be formatted with this camera
before first use or after being used with
other cameras or computers.
Submenu 2
YES*1
Completely erases the image data
in the internal memory or card
(including protected images).
NO
Cancels formatting.
*1
40
EN
Application
If [AUTO] is selected for [INTERNAL/SD] and a card
is inserted, the card will be formatted. If no card is
inserted, internal memory will be formatted.
If [IN] is selected for [INTERNAL/SD], internal
memory will be formatted whether a card is inserted
or not.
.
Restoring data in the camera
[DATA REPAIR]
r (Settings 1) X [DATA REPAIR]
Playback will become available by
performing [DATA REPAIR] when images
never appear on the monitor after q button
is pressed. However, data such as
collections and other groups created with
the PC software (ib) is deleted from the
database in the camera.
Import the data back into the camera from a
computer to playback the data created with
the PC software (ib).
Copying images in the internal memory
to the card [u COPY]
r (Settings 1) X u COPY
To copy images in the internal memory
to the card
Use HI to select an image, and press the
A button.
Changing the display language [l]
r (Settings 1) X l
“Changing the display language” (p. 14)
Submenu 2
Languages
Application
The language for the menus and
error messages displayed on the
monitor is selected.
For information on using the menus, see “Using the Menu” (p. 4).
Restoring the shooting functions to the
default settings [RESET]
Even if a computer has USB ports, proper
operation is not guaranteed in the following
cases:
r (Settings 1) X RESET
Submenu 2
Restores the following menu
functions to the default settings.
• Flash (p. 26)
• Macro (p. 26)
• Self-timer (p. 27)
• Exposure compensation (p. 27)
• White balance (p. 27)
• ISO (p. 28)
• Drive (p. 29)
• Menu functions in [I, J,
A] (p. 30 to 33)
YES
The current settings will not be
changed.
NO
Selecting a method for connecting
the camera to other devices
[USB CONNECTION]
r (Settings 1) X USB CONNECTION
Submenu 2
Application
When the camera is connected
to another device, the settings
selection screen is displayed.
AUTO
● Computers with USB ports installed using an
expansion card, etc.
Application
STORAGE
Select when connecting the
camera to a computer via a
storage device.
PC
Select when connecting a camera
and computer.
PRINT
Select when connecting to a
PictBridge-compatible printer.
System requirements
Windows
: Windows 2000 Professional/
XP Home Edition/
XP Professional/Vista/
Windows 7
Macintosh : Mac OS X v10.3 or later
When using another system other than
Windows XP (SP2 or later)/Windows Vista/
Windows 7, set to [STORAGE].
● Computers without a factory-installed OS and
home-built computers
Turning on the camera with the q
button [q POWER ON]
s (Settings 2) X q POWER ON
Submenu 2
Application
YES
Pressing the q button turns on
the camera and starts the camera
in the playback mode.
NO
The camera is not turned on. To
turn on the camera, press the
n button.
Saving the mode when the camera is
turned off [SAVE SETTINGS]
s (Settings 2) X SAVE SETTINGS
Submenu 2
Application
YES
The shooting mode is saved
when the camera is turned off and
is reactivated the next time the
camera is turned on.
NO
The shooting mode is set to P
mode when the camera is turned
on.
Choosing the opening screen display
[PW ON SETUP]
s (Settings 2) X PW ON SETUP
Submenu 2
Application
OFF
No opening screen is displayed.
ON
The opening screen is displayed
when the camera is turned on.
EN
41
Selecting the camera sound and its volume [SOUND SETTINGS]
s (Settings 2) X SOUND SETTINGS
Submenu 2
Submenu 3
SILENT MODE*1, 2
Submenu 4
OFF/ON
BEEP
SHUTTER SOUND
—
SOUND TYPE
1/2/3
VOLUME
OFF (No Sound)/
LOW/HIGH
SOUND TYPE
1/2/3
VOLUME
OFF (No Sound)/
LOW/HIGH
Selects the type and volume of the shutter
sound.
OFF (No Sound)/
LOW/HIGH
—
Selects the warning sound volume.
q VOLUME
OFF (No Sound) or
5 levels of volume
—
Selects the image playback volume.
*2
Even when [SILENT MODE] is [ON], FG can be used to adjust volume during playback.
Even when [SILENT MODE] is [ON], sound is played when images are displayed on a television.
Resetting the file names of pictures
[FILE NAME]
s (Settings 2) X FILE NAME
Folder name
DCIM
Folder name
100OLYMP
999OLYMP
Submenu 2
Automatic
numbering
RESET
AUTO
Even when a new card is inserted,
this continues the numbering for
the folder name and file name from
the previous card. This is useful for
managing all image folder names
and files names with sequential
numbers.
File name
Pmdd0001.jpg
Pmdd9999.jpg
Pmdd
Automatic
numbering
Month: 1 to C
(A=October,
B=November,
C=December)
Day: 01 to 31
Application
This resets the sequential number
for the folder name and file name
whenever a new card is inserted.*1
This is useful when grouping
images on separate cards.
*1
EN
Selects the operating sound and volume
of the camera buttons (except the shutter
button).
8
*1
42
Application
Select [ON] to disable camera sounds
(operation sounds, shutter sound, and
warning sounds) and mute sound during
playback.
The number for the folder name is reset to 100, and
the one for the file name is reset to 0001.
For information on using the menus, see “Using the Menu” (p. 4).
Adjusting the CCD and the image
processing function [PIXEL MAPPING]
s (Settings 2) X PIXEL MAPPING
This function has already been adjusted
at factory shipping, and no adjustment is
needed right after purchase. Approximately
once a year is recommended.
For best results, wait at least one minute
after taking or viewing pictures before
performing pixel mapping. If the camera is
turned off during pixel mapping, be sure to
perform it again.
Setting the date and time [X]
t (Settings 3) X X
“Setting the date, time and time zone”
(p. 13)
To select the date display order
1 Press I after setting Minute, and use
FG to select the date display order.
X
Y
M D
TIME
2010 . 02 . 26 12 : 30
To adjust the CCD and the image
processing function
Y/M/D
Date order
Press the A button when [START]
(Submenu 2) is displayed.
CANCEL MENU
SET OK
● The camera checks and adjusts the CCD and the
image processing function at the same time.
Adjusting the brightness of the monitor
[s]
s (Settings 2) X s
To adjust the monitor brightness
1 Use FG to adjust the brightness while
viewing the screen, and then press the
A button.
s
BACK MENU
SET OK
EN
43
Choosing home and alternate time zones [WORLD TIME]
t (Settings 3) X WORLD TIME
You will not be able to select a time zone using [WORLD TIME] if the camera clock has not first been
set using [X].
Submenu 2
Submenu 3
Application
x
The time in the home time zone (the time zone selected for x in
submenu 2).
y
The time in the travel destination time zone (the time zone selected
for y in submenu 2).
HOME/ALTERNATE
x*1
—
Select the home time zone (x).
y*1, 2
—
Select the travel destination time zone (y).
*1
*2
In areas where daylight saving time is in effect, use FG to turn daylight saving time ([SUMMER]) on.
When you select a time zone, the camera automatically calculates the time difference between the selected
zone and the home time zone (x) to display the time in the travel destination time zone (y).
Playing back images on a TV [TV OUT]
t (Settings 3) X TV OUT
The TV video signal system varies depending on the countries and regions. Before viewing camera
images on your TV, select the video output according to your TV’s video signal type.
Submenu 2
Submenu 3
480p/720p/1080i
OFF
Operate with the camera.
ON
Operate with the TV remote control.
VIDEO OUT
PAL
HDMI OUT
HDMI CONTROL
Application
Connecting the camera to a TV in North America, Taiwan, Korea,
Japan, and so on.
Connecting the camera to a TV in European countries, China, and
so on.
Set the playback format.
NTSC
The factory default settings differ according to the region where the camera is sold.
44
EN
For information on using the menus, see “Using the Menu” (p. 4).
To play back camera images on a TV
● Connection via AV cable
1 Use the camera to select the same video signal system as the one of connected TV
([NTSC]/[PAL]).
2 Connect the TV and camera.
STYLUS-9010/
μ-9010
STYLUS-7040/
μ-7040
Multi-connector
STYLUS-5010/
μ-5010
Multi-connector
Multi-connector
Connect to the TV video
input jack (yellow) and
audio input jack (white).
AV cable (supplied)
● Connection via HDMI cable
1 On the camera, select the digital signal format that will be connected ([480p]/[720p]/[1080i]).
2 Connect the TV and camera.
When set to [1080i], 1080i format takes priority for HDMI output. However, if this setting does not
match the input setting of the TV, the signal format is changed first to 720p and then to 480p. For
details on changing the input setting of the TV, refer to the TV’s instruction manual.
When the camera is connected to the computer by the USB cable, do not connect the HDMI
cable to the camera.
EN
45
STYLUS-9010/
μ-9010
STYLUS-7040/
μ-7040
HDMI micro
connector
STYLUS-5010/
μ-5010
HDMI micro
connector
HDMI micro
connector
HDMI cable (type D/sold separately)
Connect to the HDMI
connector on the TV.
3 Turn on the TV, and change “INPUT” to “VIDEO (an input jack connected to the camera).”
For details on changing the input source of the TV, refer to the TV’s instruction manual.
4 Turn on the camera, and use HI to select the image for playback.
Use an HDMI cable that matches the HDMI micro connector on the camera and the HDMI connector on
the TV.
When the camera and TV are connected by both an AV cable and an HDMI cable, the HDMI cable
will take priority.
Depending on the TV’s settings, the displayed images and information may become cropped.
To operate images with the TV remote
control
1 Set [HDMI CONTROL] to [ON], and turn
off the camera.
Saving battery power between shots
[POWER SAVE]
t (Settings 3) X POWER SAVE
Submenu 2
Application
2 Connect the camera and TV with an
HDMI cable. “Connection via HDMI cable”
(p. 45)
OFF
Cancels [POWER SAVE].
3 First turn on the TV, and then turn on the
camera.
ON
When the camera is not being
used for approx. 10 seconds, the
monitor automatically turns off to
save battery power.
● Operate by following the operation guide that
is displayed on the TV.
With some TVs, operations cannot be
performed with the TV remote control even
though the operation guide is displayed on
the screen.
If operations cannot be performed with the
TV remote control, set [HDMI CONTROL] to
[OFF] and operate using the camera.
46
EN
To resume standby mode
Press any button.
Printing
Direct printing (PictBridge*1)
By connecting the camera to a PictBridgecompatible printer, you can print images directly
without using a computer.
To find out if your printer supports PictBridge,
refer to the printer’s instruction manual.
*1
2
Turn on the printer, and then
connect the printer and camera.
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
STYLUS-9010/
μ-9010
Multi-connector
PictBridge is a standard for connecting digital
cameras and printers of different makers and
printing out pictures directly.
The printing modes, paper sizes, and other
parameters that can be set with the camera
vary depending on the printer that is used.
For details, refer to the printer’s instruction
manual.
For details on the available paper types,
loading paper, and installing ink cassettes,
refer to the printer’s instruction manual.
USB cable (supplied)
Printing images at the
printer’s standard settings
[EASY PRINT]
I button
In the [SETUP] menu, set [USB
CONNECTION] to [PRINT]. “Using the
Menu” (p. 4)
1
Display the image to be printed on
the monitor.
EASYPRINT START
CUSTOM PRINT OK
“Viewing images” (p. 17)
3
4
Press I to start printing.
To print another image, use HI
to select an image, and press the
A button.
To exit printing
After a selected image is displayed on the
screen, disconnect the USB cable from the
camera and printer.
EXIT
PRINT OK
EN
47
Changing the printer’s settings
for printing [CUSTOM PRINT]
1
2
3
5
Follow Steps 1 and 2 for [EASY
PRINT] (p. 47).
Submenu 4
Press the A button.
OFF/ON*1
Use FG to select the print mode,
and press the A button.
(The number of
images per sheet
varies depending
on the printer.)
The number of images per sheet
([PICS/SHEET]) is selectable only
when [MULTI PRINT] is selected
in Step 3.
*1
PRINT
ALL PRINT
MULTI PRINT
ALL INDEX
The available settings for [BORDERLESS] vary
depending on the printer.
If [STANDARD] is selected in Steps 4 and 5,
the image is printed at the printer’s standard
settings.
PRINT ORDER
EXIT MENU
Submenu 2
SET OK
This prints the image selected in
Step 6.
ALL PRINT
This prints all images stored in the
internal memory or card.
MULTI PRINT
This prints one image in a multiple
layout format.
ALL INDEX
This prints an index of all images
stored in the internal memory
or card.
PRINT ORDER*1
This prints images based on the
print reservation data on the card.
[PRINT ORDER] is available only when print
reservations have been made. “Print Reservations
(DPOF)” (p. 50)
Use FG to select [SIZE] (Submenu
3), and press I.
If the [PRINTPAPER] screen is not
displayed, the [SIZE], [BORDERLESS],
and [PICS/SHEET] are set to the printer’s
standard.
PRINTPAPER
SIZE
BORDERLESS
STANDARD
STANDARD
BACK MENU
48
EN
4/30
Application
PRINT
4
Application
The image is printed with a border
around it ([OFF]).
The image is printed to fill the
entire paper ([ON]).
PRINT MODE SELECT
*1
Use FG to select the
[BORDERLESS] or [PICS/SHEET]
settings, and press the A button.
SET OK
NORM 14M
100 0004
’10/02/26 12:30
FILE
PRINT OK
MORE
SINGLE PRINT
6
7
Use HI to select an image.
Press F to make a print reservation
for the current image. Press G to
make the detailed printer settings
for the current image.
To make the detailed printer settings
1 Use FGHI to select the setting, and
press the A button.
PRINT INFO
<x
DATE
FILE NAME
P
EXIT MENU
1
WITHOUT
WITHOUT
SET OK
Submenu
5
Submenu
6
9
Application
<×
0 to 10
This selects the number
of prints.
DATE
WITH/
WITHOUT
Selecting [WITH] prints the
images with the date.
Selecting [WITHOUT]
prints the images without
the date.
FILE NAME
WITH/
WITHOUT
Selecting [WITH] prints the
file name on the image.
Selecting [WITHOUT] does
not print any file name on
the image.
P
(Proceeds
to the
setting
screen.)
This selects a portion of
the image for printing.
Press the A button.
PRINT
PRINT
CANCEL
BACK MENU
SET OK
10 Use FG to select [PRINT], and
press the A button.
● Printing starts.
● When [OPTION SET] is selected in [ALL PRINT]
mode, [PRINT INFO] screen is displayed.
● When printing is finished, the [PRINT MODE
SELECT] screen is displayed.
To crop an image [P]
1 Use the zoom buttons to select the size
of the cropping frame, use FGHI
to move the frame, and then press the
A button.
PRINT MODE SELECT
PRINT
ALL PRINT
MULTI PRINT
ALL INDEX
PRINT ORDER
EXIT MENU
SET OK
Cropping frame
To cancel printing
SET OK
2 Use FG to select [OK], and press the
A button.
1 Press the m button while [DO NOT
REMOVE USB CABLE] is displayed.
2 Select [CANCEL] using FG and then
press the A button.
P
DO NOT REMOVE USB CABLE
OK
CANCEL
BACK MENU
8
CANCEL MENU
PRINT
SET OK
CONTINUE
CANCEL
If necessary, repeat Steps 6 and 7
to select the image to be printed,
make the detailed settings, and set
[SINGLEPRINT].
SET OK
EN
49
11 Press the m button.
3
Use FG to select [<], and press
the A button.
12 When the message [REMOVE USB
4/30
CABLE] is displayed, disconnect
the USB cable from the camera and
printer.
0
NORM 14M
100 0004
’10/02/26 12:30
Print Reservations (DPOF*1)
In print reservations, the number of prints and
date imprint option are saved in the image on
the card. This enables easy printing at a printer
or print shop supporting DPOF by using only the
print reservations on the card without a computer
or a camera.
*1
FILE
SET OK
4
Use HI to select the image for
print reservation. Use FG to select
the quantity. Press the A button.
DPOF is a standard for storing automatic printout
information from digital cameras.
X
Print reservations can be set only for the
images stored on the card. Insert a card
with recorded images before making print
reservations.
DPOF reservations set by another DPOF
device cannot be changed by this camera.
Make changes using the original device.
Making new DPOF reservations with this
camera will erase the reservations made by
the other device.
NO
DATE
TIME
BACK MENU
5
Use FG to select the [X] (date
print) screen option, and press the
A button.
DPOF print reservations can be made for up
to 999 images per card.
Submenu 2
Single-frame print
reservations [<]
1
Display the [SETUP] menu.
SET OK
Application
NO
This prints the image only.
DATE
This prints the image with the
shooting date.
TIME
This prints the image with the
shooting time.
“Using the Menu” (p. 4)
2
PRINT ORDER
From the playback menu q, select
[PRINT ORDER] and then press the
A button.
1 ( 1)
SET
CANCEL
PRINT ORDER
BACK MENU
<
U
EXIT MENU
50
EN
6
SET OK
SET OK
Use FG to select [SET], and press
the A button.
Reserving one print each of all
images on the card [U]
1
2
3
Follow Steps 1 and 2 in [<] (p. 50).
Use FG to select [U], and press
the A button.
2
1
2
3
Follow Steps 5 and 6 in [<].
Resetting all print reservation
data
1
Resetting the print reservation
data for selected images
4
Follow Steps 1 and 2 in [<] (p. 40).
Select either [<] or [U], and press
the A button.
5
6
PRINT ORDER SETTING
PRINT ORDERED
3
Use FG to select [<], and press
the A button.
Use FG to select [KEEP] and
press the A button.
Use HI to select the image with
the print reservation you want to
cancel. Use FG to set the print
quantity to “0”.
If necessary, repeat Step 4, and then
press the A button when finished.
Use FG to select the [X] (date
print) screen option, and press the
A button.
● The settings are applied to the remaining images
RESET
KEEP
BACK MENU
Follow Steps 1 and 2 in [<] (p. 50).
with the print reservation data.
SET OK
7
Use FG to select [SET], and press
the A button.
Use FG to select [RESET], and
press the A button.
EN
51
Usage Tips
If the camera does not work as intended, or if
an error message is displayed on the screen,
and you are unsure of what to do, refer to the
information below to fix the problem(s).
Troubleshooting
Battery
“The camera does not work even when
batteries are installed”.
● Insert recharged batteries in the correct direction.
“Inserting the battery” (p. 10), “Battery charge and
camera setup” (p. 10), “Charging the battery with
the included USB-AC adapter” (p. 12)
● Battery performance may have been reduced
temporarily due to low temperature. Take the
batteries out of the camera, and warm them by
putting them in your pocket for a while.
Card/Internal memory
“An error message is displayed”.
“Error message” (p. 53)
Shutter button
“No picture is taken when the shutter
button is pressed”.
● Cancel sleep mode.
To save battery power, the camera automatically
goes into sleep mode and the monitor turns off
if there is no operation for 3 minutes when the
camera is turned on. No picture is taken even if
the shutter button is fully pressed in this mode.
Operate the zoom buttons or other buttons to
restore the camera from sleep mode before
taking a picture. If the camera is left for another
12 minutes, it automatically turns off. Press the
n button to turn the camera on.
● Press the q button to switch to the shooting
mode.
● Wait until #(flash charge) stops blinking before
taking pictures.
● With prolonged camera use, the internal
temperature may increase, resulting in automatic
shutdown. If this occurs, remove the battery
from the camera and wait until the camera
has sufficiently cooled. The camera’s external
temperature may also increase during use,
however this is normal and does not indicate
malfunction.
52
EN
Monitor
“Difficult to see”.
● Condensation*1 may have occurred. Turn off the
power, and wait for the camera body to become
acclimated to the surrounding temperature and dry
out before taking pictures.
*1
Dew drops can form in the camera when it is
suddenly taken from a cold location into a warm,
humid room.
“Vertical lines appear on the screen”.
● This condition may occur when the camera is
pointed at an extremely bright subject under a
clear sky and so on. The lines do not appear,
however, in the final image.
“The light is caught in the picture”.
● Shooting with flash in dark situations results in
an image with many flash reflections on dust in
the air.
Date and time function
“Date and time settings return to the
default setting”.
● If the batteries are removed and left out of the
camera for about 3 days*2, the date and time
settings return to the default setting, and must
be reset.
*2
The time until the date and time settings return
to the default setting varies depending on how
long the batteries have been loaded.
“Setting the date, time and time zone” (p. 13)
Miscellaneous
“The camera makes a noise when taking
pictures”.
● The camera may activate the lens and make a
noise even if no operation is performed. This
is because the camera automatically performs
actions of auto focus as far as it is ready to shoot.
Error message
Error message
When one of the messages below is
displayed on the monitor, check the
corrective action.
Error message
NO INK
Corrective action
JAMMED
CARD ERROR
WRITE
PROTECT
Card problem
Insert a new card.
Card problem
The card write-protect switch is
set to the “LOCK” side. Release
the switch.
MEMORY FULL
Internal memory problem
• Insert a card.
• Erase unwanted images.*1
CARD FULL
Card problem
• Replace the card.
• Erase unwanted images.*1
CARD SETUP
POWER OFF
FORMAT
SET OK
MEMORY SETUP
POWER OFF
MEMORY FORMAT
SET OK
NO PICTURE
PICTURE
ERROR
THE IMAGE
CANNOT
BE EDITED
BATTERY
EMPTY
NO
CONNECTION
NO PAPER
SETTINGS
CHANGED*3
Card problem
Use FG to select [FORMAT],
and press the A button. Next,
use FG to select [YES], and
press the A button.*2
Internal memory problem
Use FG to select [MEMORY
FORMAT], and press the
A button. Next, use FG to
select [YES], and press the
A button.*2
PRINT ERROR
CANNOT PRINT*4
*1
*2
*3
*4
Corrective action
Printer problem
Refill the ink in the printer.
Printer problem
Remove the jammed paper.
Printer problem
Return to the status where the
printer can be used.
Printer problem
Turn off the camera and printer,
check the printer for any
problems, and then turn the
power on again.
Problem with selected image
Use a computer to print.
Before erasing important images, download them to
a computer.
All data will be erased.
This is displayed, for instance, when the printer’s
paper tray has been removed. Do not operate
the printer while making the print settings on the
camera.
This camera may be unable to print images taken by
other cameras.
Internal memory/Card problem
Take pictures before viewing
them.
Problem with selected image
Use photo retouch software,
etc. to view the image on a
computer. If the image still
cannot be viewed, the image file
is corrupted.
Problem with selected image
Use photo retouch software, etc.
to edit the image on a computer.
Battery problem
Charge the battery.
Connection problem
Connect the camera and
computer or printer correctly.
Printer problem
Load paper into the printer.
EN
53
Shooting tips
When you are unsure of how to take a picture
that you envision, refer to the information below.
Fast-moving object
Focusing
“Focusing on the subject”
● Taking a picture of a subject not in the center
The subject is not in the center
of the frame
of the screen
After focusing on an object at the same distance
as the subject, compose the shot, and take the
picture.
Camera shake
Pressing the shutter button halfway (p. 15)
● Set [AF MODE] (p. 31) to [FACE/iESP]
● Taking a picture in [AF TRACKING] mode
“Taking pictures without camera shake”
● Taking pictures using [IMAGE STABILIZER]
(p. 31)
(p. 32)
The camera tracks the subject movement
automatically to focus on it continuously.
When a picture is taken of a shadowy subject, the
CCD*1 shifts to correct for camera shake even if
the ISO speed is not increased. This function is
also effective when taking pictures at a high zoom
magnification.
● Taking a picture of subjects where autofocus
is difficult
In the following cases, after focusing on an object
(by pressing the shutter button halfway down) with
high contrast at the same distance as the subject,
compose the shot, and take the picture.
*1
A device that takes light received through the
lens and converts it into electric signals.
● Shooting movies using [IS MOVIE MODE]
(p. 32)
● Select C (SPORT) in the scene mode (p. 22)
Subjects with low contrast
The C (SPORT) mode uses a fast shutter speed
and can reduce the blur incurred by a moving
subject.
● Taking pictures at a high ISO sensitivity
When extremely bright objects
appear in the center of the
screen
Object with no vertical lines*1
*1
It is also effective to compose the shot by holding the
camera vertically to focus, and then returning to the
horizontal position to take the picture.
When objects are at different
distances
54
EN
If a high ISO sensitivity is selected, pictures can
be taken at a high shutter speed even at locations
where a flash cannot be used.
“Selecting the ISO sensitivity” (p. 28)
Exposure (brightness)
“Taking pictures with the right
brightness”
● Taking pictures of a subject against a backlight
Faces or backgrounds are bright even when shot
against backlight.
[SHADOW ADJUST] (p. 31)
● Taking pictures using [FACE/iESP] (p. 31)
Appropriate exposure is obtained for a face
against backlight, and the face is brightened.
● Taking pictures using [n] for [ESP/n]
(p. 31)
Brightness is matched with a subject in the center
of the screen and the image is not affected by
background light.
● Taking pictures using [FILL IN] (p. 26) flash
A subject against backlight is brightened.
● Taking pictures of a white beach or snow
scene
Set the mode to [q BEACH & SNOW] (p. 22)
● Taking pictures using exposure compensation
(p. 27)
Adjust the brightness while viewing the screen
for taking the picture. Normally, taking pictures of
white subjects (such as snow) results in images
that are darker than the actual subject. Use the
exposure compensation to adjust in the positive
(+) direction to express whites as they appear.
When taking pictures of black subjects, on the
other hand, it is effective to adjust in the negative
(-) direction.
Color hue
Image quality
“Taking sharper pictures”
● Taking pictures with the optical zoom
Avoid using digital zoom (p. 32) to take pictures.
● Taking pictures at a low ISO sensitivity
If the picture is taken with a high ISO sensitivity,
noise (small colored spots and color unevenness
that were not in the original image) can occur, and
the image can appear grainy.
“Selecting the ISO sensitivity” (p. 28)
Panorama
“Taking pictures so that the frames are
stitched smoothly”
● A tip for panoramic shooting
Taking pictures by pivoting with the camera at the
center prevents shifting of the image. When taking
pictures of close objects in particular, pivoting with
the lens end at the center produces favorable
results.
[PANORAMA] (p. 23)
Batteries
“Making batteries last longer”
● Avoid any of the following operations when not
actually taking pictures because they deplete
the battery power
● Repeatedly pressing the shutter button
halfway.
● Repeatedly using the zoom.
● Set [POWER SAVE] (p. 46) to [ON]
“Taking pictures with colors at the same
shade as they appear”
● Taking pictures by selecting white balance
(p. 28)
Best results in most environments can normally
be obtained with the [WB AUTO] setting, but for
some subjects, you should try experimenting
with different settings. (This is especially true for
sunshade under a clear sky, mixed natural and
artificial light settings, and so on.)
● Taking pictures using [FILL IN] (p. 26) flash
Use of the flash is also effective for shooting under
fluorescent and other artificial lighting.
EN
55
Playback/Editing tips
Playback
“Playing images in the internal memory
and card”
● Remove the card and display the images in
internal memory
● “Inserting the battery” (p. 10), “Inserting the
SD/SDHC memory card (sold separately)”
(p. 14)
● Selecting a storage device
[INTERNAL/SD] (p. 40)
“Viewing images with high picture quality
on a high-definition TV”
● Connect the camera to the TV using an HDMI
cable (sold separately)
● “To play back camera images on a TV” (p. 45)
Editing
“Erasing the sound recorded to a still
image”
● Record over the sound with silence when
playing back the image
“Adding sound to still images [R]” (p. 39)
56
EN
Appendix
Camera care
Exterior
• Wipe gently with a soft cloth. If the camera is
very dirty, soak the cloth in mild soapy water
and wring well. Wipe the camera with the
damp cloth and then dry it with a dry cloth. If
you have used the camera at the beach, use a
cloth soaked in clean water and wrung well.
Monitor
• Wipe gently with a soft cloth.
Lens
• Blow dust off the lens with a commercial
blower, then wipe gently with a lens cleaner.
Battery/USB-AC adapter
• Wipe gently with a soft, dry cloth.
Do not use strong solvents such as benzene
or alcohol, or chemically treated cloth.
Mold may form on the lens surface if the
lens is left dirty.
Storage
• When storing the camera for extended
periods, remove the battery, AC adapter and
card, and keep in a cool, dry place that is well
ventilated.
• Periodically insert the battery and test the
camera functions.
Avoid leaving the camera in places where
chemical products are handled since this
may result in corrosion.
Battery, USB-AC adapter
(included), Charger (sold
separately)
• This camera uses one Olympus lithium ion
battery (LI-50B*/LI-42B/LI-40B). No other type
of batteries can be used.
* STYLUS-9010/μ-9010 only
Caution:
There is a risk of explosion if the battery is
replaced with the incorrect battery type.
Dispose of the used battery following the
instructions. (p. 64)
• Power consumption by the camera varies
depending on which functions are used.
• During the conditions described below, power
is consumed continuously and the battery
becomes exhausted quickly.
• The zoom is used repeatedly.
• The shutter button is pressed halfway
repeatedly in shooting mode, activating the
auto focus.
• A picture is displayed on the monitor for an
extended period of time.
• The camera is connected to a printer.
• Using an exhausted battery may cause the
camera to turn off without displaying the
battery level warning.
• The rechargeable battery is not fully charged
at the time of purchase. Before using the
camera, charge it by connecting it to a
computer, or charge it using the included
USB-AC adapter (F-2AC), a separately
sold AC adapter (F-1AC/D-7AC) or charger
(LI-50C*/LI-41C/LI-40C).
* STYLUS-9010/μ-9010 only
• STYLUS-9010/μ-9010: When the included
USB-AC adapter (F-2AC) is used, charging
usually takes approximately 3.5 hours (varies
on usage).
STYLUS-7040/μ-7040, STYLUS-5010/μ-5010:
When the included USB-AC adapter (F-2AC)
is used, charging usually takes approximately
3 hours (varies on usage).
• The included USB-AC adapter (F-2AC) has
been designed to be used for charging and
playback. Make sure that shooting is not being
used while the USB-AC adapter is connected
to the camera.
EN
57
• The included USB-AC adapter (F-2AC) is
designed to be used only with this camera.
Other cameras cannot be charged with this
USB-AC adapter.
• Do not connect the included USB-AC adapter
(F-2AC) to equipment other than this camera.
• For plug-in type USB-AC adapter:
The included USB-AC adapter (F-2AC) is
intended to be correctly orientated in a vertical
or floor mount position.
Charging the battery by
connecting the camera to a
computer
The battery can be charged by connecting the
camera to a computer.
Using a separately sold AC
adapter
An AC adapter (D-7AC/sold separately) is useful
for time-consuming tasks such as when running
a slideshow for a long period of time. To use
a separately sold AC adapter for this camera,
the multi-adapter (CB-MA1, CB-MA3/sold
separately) is required.
Do not use any other AC adapter with this
camera.
Using a separately sold
charger
A charger (LI-50C*/LI-41C/LI-40C: sold
separately) can be used to charge the battery. In
this case, remove the battery from the camera
and set the battery to the charger.
* STYLUS-9010/μ-9010 only
Using your charger and
USB-AC adapter abroad
• The charger and USB-AC adapter can be
used in most home electrical sources within
the range of 100 V to 240 V AC (50/60Hz)
around the world. However, depending on the
country or area you are in, the AC wall outlet
may be shaped differently and the charger and
USB-AC adapter may require a plug adapter to
match the wall outlet. For details, ask at your
local electrical shop or travel agent.
• Do not use travel voltage converters as
they could damage your charger and
USB-AC adapter.
Using a SD/SDHC memory card
A card (and internal memory) also corresponds
to the film that records images in a film camera.
Otherwise, the recorded images (data) can be
erased, and retouching is also available with
the use of a computer. Cards can be removed
from the camera and exchanged, but this is
not possible with the internal memory. Use of
larger capacity cards enables you to take more
pictures.
SD/SDHC memory card write-protect
switch
The SD/SDHC memory card body has a
write-protect switch. If you set the switch to
the “LOCK” side, you will not be able to write
to the card, delete data or format. Return the
switch to enable writing.
LOCK
Cards compatible with this camera
SD/SDHC memory cards (for more
information, visit the Olympus website)
58
EN
Using a new card
Readout/recording process of the card
Cards must be formatted with this camera
before first use or after being used with other
cameras or computers.
[MEMORY FORMAT]/[FORMAT] (p. 40)
Checking the image saving location
The memory indicator shows whether the
internal memory or card is being used during
shooting and playback.
During shooting, the current memory
indicator blinks red while the camera is
writing data. Never open the battery/card
compartment cover or unplug the USB
cable. This can not only damage the image
data but also render the internal memory or
card unusable.
P
Current memory indicator
v: Internal memory is being used
w: Card is being used
P
0.0
Current memory
indicator
WB
AUTO
ISO
AUTO
00:34
4 14M
Flashes in red
0.0
WB
AUTO
ISO
AUTO
00:34
4 14M
4/30
Shooting mode
’10/02/26 12:30
Playback mode
Even if [MEMORY FORMAT]/[FORMAT],
[ERASE], [ERASE EVENT], [SEL. IMAGE],
or [ALL ERASE] is performed, the data in
the card is not completely erased. When
disposing of the card, damage the card to
prevent the disclosure of personal data.
EN
59
Number of storable pictures (still images)/Continuous recording length (movies) in the
internal memory and SD/SDHC memory cards
The figures in the following tables are quoted only as a rough guideline. The actual number of
storable pictures or continuous recording lengths will differ according to the shooting conditions and
memory cards used.
The figures in the table below are the number of the storable pictures when using the internal
memory formatted. [MEMORY FORMAT]/[FORMAT] (p. 40)
Still pictures
IMAGE SIZE
6 4288×3216
4 3264×2448
n 2560×1920
3 2048×1536
2 1600×1200
1 1280×960
7 640×480
K 3968×2232
0 1920×1080
IMAGE SIZE
6 4288×3216
4 3264×2448
n 2560×1920
3 2048×1536
2 1600×1200
1 1280×960
7 640×480
K 3968×2232
0 1920×1080
60
EN
Number of storable still pictures
Internal memory
COMPRESSTYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
SION
With
Without
With
Without
With
Without
sound
sound
sound
sound
sound
sound
265
266
265
266
123
124
L
518
523
518
523
242
244
M
452
456
452
456
210
212
L
877
891
877
891
408
414
M
722
731
722
731
335
340
L
1,426
1,463
1,426
1,462
671
688
M
1,141
1,164
1,140
1,164
530
541
L
2,194
2,282
2,194
2,281
1,020
1,060
M
1,840
1,902
1,840
1,901
855
884
L
3,356
3,566
3,355
3,565
1,607
1,711
M
2,717
2,853
2,716
2,852
1,293
1,360
L
5,187
5,706
5,186
5,704
2,411
2,652
M
8,151
9,510
8,149
9,508
4,080
4,822
L
14,265
19,020
14,262
19,016
6,630
8,841
M
350
352
349
352
163
164
L
687
695
687
695
319
323
M
1,678
1,729
1,677
1,728
791
816
L
3,170
3,356
3,169
3,355
1,515
1,607
M
Number of storable still pictures
SD/SDHC memory card (1 GB)
COMPRESSTYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
SION
With
Without
With
Without
With
Without
sound
sound
sound
sound
sound
sound
141
141
141
141
141
141
L
276
279
276
278
276
278
M
240
242
240
242
240
242
L
465
473
465
472
465
472
M
383
388
383
387
383
387
L
766
786
766
786
766
786
M
605
617
605
617
605
617
L
1,164
1,210
1,163
1,210
1,163
1,210
M
976
1,009
976
1,008
976
1,008
L
1,834
1,953
1,834
1,952
1,834
1,952
M
1,476
1,552
1,476
1,551
1,476
1,551
L
2,752
3,027
2,751
3,026
2,751
3,026
M
4,657
5,504
4,655
5,502
4,655
5,502
L
7,568
10,091
7,565
10,087
7,565
10,087
M
186
187
186
187
186
187
L
364
369
364
369
364
369
M
903
931
903
931
903
931
L
1,729
1,834
1,729
1,834
1,729
1,834
M
Movies
IMAGE SIZE
L 1280×720
IMAGE
QUALITY
L
M
L
8 640×480
M
9 320×240
IMAGE SIZE
L 1280×720
L
IMAGE
QUALITY
L
M
L
8 640×480
M
9 320×240
L
Continuous recording length
Internal memory
STYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
With
Without
With
Without
With
Without
sound
sound
sound
sound
sound
sound
19 min.
20 min.
19 min.
20 min.
9 min.
9 min.
53 sec.
13 sec.
53 sec.
13 sec.
13 sec.
22 sec.
18 min.
18 min.
29 min.
29 min.
29 min.
29 min.
9 sec.
44 sec.
39 min.
40 min.
39 min.
40 min.
18 min.
18 min.
9 sec.
25 sec.
8 sec.
24 sec.
9 sec.
44 sec.
75 min.
80 min.
75 min.
80 min.
35 min.
37 min.
51 sec.
43 sec.
50 sec.
42 sec.
10 sec.
25 sec.
75 min.
80 min.
75 min.
80 min.
35 min.
37 min.
51 sec.
43 sec.
50 sec.
42 sec.
10 sec.
25 sec.
Continuous recording length
SD/SDHC memory card (1 GB)
STYLUS-9010/μ-9010 STYLUS-7040/μ-7040 STYLUS-5010/μ-5010
With
Without
With
Without
With
Without
sound
sound
sound
sound
sound
sound
10 min.
10 min.
10 min.
10 min.
10 min.
10 min.
32 sec.
42 sec.
31 sec.
42 sec.
31 sec.
42 sec.
20 min.
21 min.
20 min.
21 min.
20 min.
21 min.
43 sec.
24 sec.
43 sec.
23 sec.
43 sec.
23 sec.
20 min.
21 min.
20 min.
21 min.
20 min.
21 min.
43 sec.
24 sec.
43 sec.
23 sec.
43 sec.
23 sec.
40 min.
42 min.
40 min.
42 min.
40 min.
42 min.
10 sec.
44 sec.
9 sec.
43 sec.
9 sec.
43 sec.
40 min.
42 min.
40 min.
42 min.
40 min.
42 min.
10 sec.
44 sec.
9 sec.
43 sec.
9 sec.
43 sec.
The maximum file size of a single movie is 4 GB, regardless of the capacity of the card.
Increasing the number of pictures that can be taken
Either erase unwanted images, or connect the camera to a computer or other device to save
the images, and then erase the images in the internal memory or card. [ERASE] (p. 18, 38),
[ERASE EVENT] (p. 38), [SEL. IMAGE] (p. 38), [ALL ERASE] (p. 38), [MEMORY FORMAT]/
[FORMAT] (p. 40)
EN
61
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED OLYMPUS
SERVICE PERSONNEL.
DANGER
WARNING
CAUTION
An exclamation mark enclosed in a
triangle alerts you to important operating
and maintenance instructions in the
documentation provided with the product.
If the product is used without observing
the information given under this symbol,
serious injury or death may result.
If the product is used without observing the
information given under this symbol, injury
or death may result.
If the product is used without observing the
information given under this symbol, minor
personal injury, damage to the equipment,
or loss of valuable data may result.
WARNING!
TO AVOID THE RISK OF FIRE OR ELECTRICAL SHOCK,
NEVER DISASSEMBLE, EXPOSE THIS PRODUCT TO
WATER OR OPERATE IN A HIGH HUMIDITY ENVIRONMENT.
General Precautions
Read All Instructions — Before you use the
product, read all operating instructions. Save all
manuals and documentation for future reference.
Cleaning — Always unplug this product from the
wall outlet before cleaning. Use only a damp
cloth for cleaning. Never use any type of liquid or
aerosol cleaner, or any type of organic solvent to
clean this product.
Attachments — For your safety, and to avoid
damaging the product, use only accessories
recommended by Olympus.
Water and Moisture — For precautions on
products with weatherproof designs, read the
weatherproofing sections.
Location — To avoid damage to the product, mount
the product securely on a stable tripod, stand,
or bracket.
Power Source — Connect this product only to the
power source described on the product label.
Lightning — If a lightning storm occurs while using
an AC adapter, remove it from the wall outlet
immediately.
Foreign Objects — To avoid personal injury, never
insert a metal object into the product.
Heat — Never use or store this product near any
heat source such as a radiator, heat register,
stove, or any type of equipment or appliance that
generates heat, including stereo amplifiers.
62
EN
Handling the Camera
WARNING
• Do not use the camera near flammable or
explosive gases.
• Do not use the flash and LED on people
(infants, small children, etc.) at close range.
• You must be at least 1 m (3 ft.) away from the
faces of your subjects. Firing the flash too close
to the subject’s eyes could cause a momentary
loss of vision.
• Keep young children and infants away from
the camera.
• Always use and store the camera out of the
reach of young children and infants to prevent
the following dangerous situations which could
cause serious injury:
• Becoming entangled in the camera strap,
causing strangulation.
• Accidentally swallowing the battery, cards or
other small parts.
• Accidentally firing the flash into their own eyes
or those of another child.
• Accidentally being injured by the moving parts
of the camera.
• Do not look at the sun or strong lights with the
camera.
• Do not use or store the camera in dusty or
humid places.
• Do not cover the flash with a hand while firing.
• Use SD/SDHC memory cards only. Never use
other types of cards.
If you accidently insert another type of card into
the camera, contact an authorized distributor or
service center. Do not try to remove the card by
force.
CAUTION
• Stop using the camera immediately if you
notice any unusual odors, noise, or smoke
around it.
• Never remove the batteries with bare hands,
which may cause a fire or burn your hands.
• Never hold or operate the camera with wet
hands.
• Do not leave the camera in places where it may
be subject to extremely high temperatures.
• Doing so may cause parts to deteriorate and, in
some circumstances, cause the camera to catch
fire. Do not use the charger or AC adapter if it is
covered (such as a blanket). This could cause
overheating, resulting in fire.
• Handle the camera with care to avoid getting a
low-temperature burn.
• When the camera contains metal parts,
overheating can result in a low-temperature
burn. Pay attention to the following:
• When used for a long period, the camera will
get hot. If you hold on to the camera in this
state, a low-temperature burn may be caused.
• In places subject to extremely cold
temperatures, the temperature of the camera’s
body may be lower than the environmental
temperature. If possible, wear gloves when
handling the camera in cold temperatures.
• Be careful with the strap.
• Be careful with the strap when you carry the
camera. It could easily catch on stray objects
and cause serious damage.
Battery Handling Precautions
Follow these important guidelines to prevent
batteries from leaking, overheating, burning,
exploding, or causing electrical shocks or
burns.
DANGER
• The camera uses a lithium ion battery specified
by Olympus. Charge the battery with the specified
AC adapter or charger. Do not use any other AC
adapters or chargers.
• Never heat or incinerate batteries.
• Take precautions when carrying or storing
batteries to prevent them from coming into contact
with any metal objects such as jewelry, pins,
fasteners, etc.
• Never store batteries where they will be
exposed to direct sunlight, or subjected to high
temperatures in a hot vehicle, near a heat source,
etc.
• To prevent causing battery leaks or damaging their
terminals, carefully follow all instructions regarding
the use of batteries. Never attempt to disassemble
a battery or modify it in any way, solder, etc.
• If battery fluid gets into your eyes, flush your eyes
immediately with clear, cold running water and
seek medical attention immediately.
• Always store batteries out of the reach of small
children. If a child accidentally swallows a battery,
seek medical attention immediately.
WARNING
• Keep batteries dry at all times.
• To prevent batteries from leaking, overheating,
or causing a fire or explosion, use only batteries
recommended for use with this product.
• Insert the battery carefully as described in the
operating instructions.
• If rechargeable batteries have not been recharged
within the specified time, stop charging them and
do not use them.
• Do not use a battery if it is cracked or broken.
• If a battery leaks, becomes discolored or
deformed, or becomes abnormal in any other way
during operation, stop using the camera.
• If a battery leaks fluid onto your clothing or skin,
remove the clothing and flush the affected area
with clean, running cold water immediately. If
the fluid burns your skin, seek medical attention
immediately.
• Never subject batteries to strong shocks or
continuous vibration.
CAUTION
• Before loading, always inspect the battery carefully
for leaks, discoloration, warping, or any other
abnormality.
• The battery may become hot during prolonged
use. To avoid minor burns, do not remove it
immediately after using the camera.
• Always unload the battery from the camera before
storing the camera for a long period.
Caution for Usage Environment
• To protect the high-precision technology contained
in this product, never leave the camera in the
places listed below, no matter if in use or storage:
• Places where temperatures and/or humidity
are high or go through extreme changes.
Direct sunlight, beaches, locked cars, or near
other heat sources (stove, radiator, etc.) or
humidifiers.
• In sandy or dusty environments.
• Near flammable items or explosives.
• In wet places, such as bathrooms or in the rain.
When using products with weatherproof designs,
read their manuals as well.
• In places prone to strong vibrations.
• Never drop the camera or subject it to severe
shocks or vibrations.
• When mounted on a tripod, adjust the position of
the camera with the tripod head. Do not twist the
camera.
• Do not touch electric contacts on cameras.
• Do not leave the camera pointed directly at the
sun. This may cause lens or shutter curtain
damage, color failure, ghosting on the CCD, or
may possibly cause fires.
• Do not push or pull severely on the lens.
• Before storing the camera for a long period,
remove the batteries. Select a cool, dry location
for storage to prevent condensation or mold from
forming inside the camera. After storage, test the
camera by turning it on and pressing the shutter
button to make sure that it is operating normally.
• Always observe the operating environment
restrictions described in the camera’s manual.
EN
63
Battery Handling Precautions
• This camera uses a lithium ion battery specified by
Olympus. Do not use any other type of battery.
• If the battery’s terminals get wet or greasy, camera
contact failure may result. Wipe the battery well
with a dry cloth before use.
• Always charge a battery when using it for the first
time, or if it has not been used for a long period.
• When operating the camera with battery power
at low temperatures, try to keep the camera and
spare battery as warm as possible. A battery that
has run down at low temperatures may be restored
after it is warmed at room temperature.
• The number of pictures you can take may vary
depending on the shooting conditions or battery.
• Before going on a long trip, and especially before
traveling abroad, purchase extra batteries. A
recommended battery may be difficult to obtain
while traveling.
• Please recycle batteries to help save our planet’s
resources. When you throw away dead batteries,
be sure to cover their terminals and always
observe local laws and regulations.
LCD Monitor
• Do not push the monitor forcibly; otherwise the
image may become vague, resulting in a playback
mode failure or damage to the monitor.
• A strip of light may appear on the top/bottom of the
monitor, but this is not a malfunction.
• When a subject is viewed diagonally in the
camera, the edges may appear zigzagged on the
monitor. This is not a malfunction; it will be less
noticeable in playback mode.
• In places subject to low temperatures, the LCD
monitor may take a long time to turn on or its
color may change temporarily. When using the
camera in extremely cold places, it is a good idea
to occasionally place it in a warm place. An LCD
monitor exhibiting poor performance due to low
temperatures will recover in normal temperatures.
• The LCD used for the monitor is made with
high-precision technology. However, black spots
or bright spots of light may appear constantly on
the LCD Monitor. Due to its characteristics or the
angle at which you are viewing the monitor, the
spot may not be uniform in color and brightness.
This is not a malfunction.
Legal and Other Notices
• Olympus makes no representations or warranties
regarding any damages, or benefit expected by
using this unit lawfully, or any request from a third
person, which are caused by the inappropriate use
of this product.
• Olympus makes no representations or warranties
regarding any damages or any benefit expected
by using this unit lawfully which are caused by
erasing picture data.
64
EN
Disclaimer of Warranty
• Olympus makes no representations or warranties,
either expressed or implied, by or concerning any
content of these written materials or software, and
in no event shall be liable for any implied warranty
of merchantability or fitness for any particular
purpose or for any consequential, incidental or
indirect damages (including but not limited to
damages for loss of business profits, business
interruption and loss of business information)
arising from the use or inability to use these
written materials or software or equipment. Some
countries do not allow the exclusion or limitation
of liability for consequential or incidental damages
or of the implied warranty, so the above limitations
may not apply to you.
• Olympus reserves all rights to this manual.
Warning
Unauthorized photographing or use of
copyrighted material may violate applicable
copyright laws. Olympus assumes no
responsibility for unauthorized photographing,
use or other acts that infringe upon the rights of
copyright owners.
Copyright Notice
All rights reserved. No part of these written
materials or this software may be reproduced
or used in any form or by any means, electronic
or mechanical, including photocopying and
recording or the use of any type of information
storage and retrieval system, without the prior
written permission of Olympus. No liability
is assumed with respect to the use of the
information contained in these written materials
or software, or for damages resulting from
the use of the information contained therein.
Olympus reserves the right to alter the features
and contents of this publication or software
without obligation or advance notice.
FCC Notice
• Radio and Television Interference
• Changes or modifications not expressly approved
by the manufacturer may void the user’s authority
to operate this equipment. This equipment has
been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation.
• This equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
• However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Adjust or relocate the receiving antenna.
• Increase the distance between the camera and
receiver.
• Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
• Consult your dealer or an experienced radio/TV
technician for help. Only the OLYMPUS-supplied
USB cable should be used to connect the
camera to USB enabled personal computers
(PC).
Any unauthorized changes or modifications to
this equipment would void the user’s authority
to operate it.
Use Only Dedicated Rechargeable
Battery, Battery Charger and
AC adapter
We strongly recommend that you use only
the genuine Olympus dedicated rechargeable
battery, battery charger and AC adapter with
this camera. Using a non-genuine rechargeable
battery, battery charger and/or AC adapter
may result in fire or personal injury due to
leakage, heating, ignition or damage to the
battery. Olympus does not assume any liability
for accidents or damage that may result from
the use of a battery, battery charger and/or
AC adapter that are not genuine Olympus
accessories.
EN
65
Representative plug of power supply cord of countries/regions around the
world
A Type
B Type
(American Type) (British Type)
BF Type
(British Type)
B3 Type
(British Type)
C Type
(CEE Type)
SE Type
(CEE Type)
O Type
(Oceania Type)
The representative supply voltage and plug type are described in this chart.
Depending on the area, different types of plugs and supply voltages are used.
Attention: Power cord meeting demands from each country shall be used.
- For only the United States
Use a UL Listed, 1.5 - 4.5 m (5 - 15 ft), Type SPT-2 or NISPT-2, AWG no. 18 power supply cord, rated for
125 V 7 A, with a non-polarized NEMA 1-15P plug rated for 125 V 15 A”.
66
EN
Europe
Countries/Regions
Austria
Belgium
Czech
Denmark
Finland
France
Germany
Greece
Hungary
Iceland
Ireland
Italy
Luxemburg
Netherlands
Norway
Poland
Portugal
Romania
Russia
Slovak
Spain
Sweden
Switzerland
UK
Voltage
230
230
220
230
230
230
230
220
220
230
230
220
230
230
230
220
230
220
220
220
127/230
230
230
240
Frequency (Hz) Plug type
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C/BF
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
C
50
BF
Asia
Countries/Regions
China
Hong Kong
India
Indonesia
Japan
Korea (rep)
Malaysia
Philippines
Singapore
Taiwan
Thailand
Vietnam
Voltage
220
200/220
230/240
127/230
100
220
240
220/230
230
110
220
220
Frequency (Hz) Plug type
50
A
50
BF
50
C
50
C
50/60
A
60
C
50
BF
60
A/C
50
BF
60
A
50
C/BF
50
A/C
Oceania
Countries/Regions
Australia
New Zealand
Voltage
240
230/240
Frequency (Hz) Plug type
50
O
50
O
North America
Countries/Regions
Canada
USA
Voltage
120
120
Frequency (Hz) Plug type
60
A
60
A
Central America
Countries/Regions
Bahamas
Costa Rica
Cuba
Dominican (rep)
El Salvador
Guatemala
Honduras
Jamaica
Mexico
Nicaragua
Panama
Voltage
120/240
110
110/220
110
110
120
110
110
120/127
120/240
110/220
Frequency (Hz) Plug type
60
A
60
A
60
A/C
60
A
60
A
60
A
60
A
50
A
60
A
60
A
60
A
South America
Countries/Regions
Argentina
Brazil
Chile
Colombia
Peru
Venezuela
Voltage
220
127/220
220
120
220
120
Frequency (Hz) Plug type
50
C/BF/O
60
A/C
50
C
60
A
60
A/C
60
A
Middle East
Countries/Regions
Iran
Iraq
Israel
Saudi Arabia
Turkey
UAE
Voltage
220
220
230
127/220
220
240
Frequency (Hz) Plug type
50
C/BF
50
C/BF
50
C
50
A/C/BF
50
C
50
C/BF
Africa
Countries/Regions
Algeria
Congo (dem)
Egypt
Ethiopia
Kenya
Nigeria
South Africa
Tanzania
Tunisia
Voltage
127/220
220
220
220
240
230
220/230
230
220
Frequency (Hz) Plug type
50
C
50
C
50
C
50
C
50
C/BF
50
C/BF
50
C/BF
50
C/BF
50
C
For customers in North and South
America
For customers in USA
Declaration of Conformity
Model Number
: STYLUS-9010/μ-9010
STYLUS-7040/μ-7040
STYLUS-5010/μ-5010
Trade Name
: OLYMPUS
Responsible Party
:
Address
Telephone Number
: 3500 Corporate
Parkway, P.O. Box
610, Center Valley, PA
18034-0610, U.S.A.
: 484-896-5000
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
For customers in Canada
This Class B digital apparatus meets all
requirements of the Canadian InterferenceCausing Equipment Regulations.
OLYMPUS WORLDWIDE LIMITED
WARRANTY - IMAGING PRODUCTS
Olympus warrants that the enclosed Olympus®
imaging product(s) and related Olympus®
accessories (individually a “Product” and
collectively the “Products”) will be free from
defects in materials and workmanship under
normal use and service for a period of one (1)
year from the date of purchase.
If any Product proves to be defective within the
one-year warranty period, the customer must
return the defective Product to any of Olympus
Service Centers, following the procedure
set forth below (See “WHAT TO DO WHEN
SERVICE IS NEEDED”).
Olympus, at its sole discretion, will repair,
replace, or adjust the defective Product, provided
that Olympus investigation and factory inspection
disclose that (a) such defect developed under
normal and proper use and (b) the Product is
covered under this limited warranty.
Repair, replacement, or adjustment of defective
Products shall be Olympus’s sole obligation and
the customer’s sole remedy hereunder.
The customer is liable and shall pay for shipment
of the Products to the Olympus Service Center.
Olympus shall not be obligated to perform
preventive maintenance, installation,
deinstallation, or maintenance.
Olympus reserves the right to (i) use
reconditioned, refurbished, and/or serviceable
used parts (that meet Olympus’s quality
assurance standards) for warranty or any other
repairs and (ii) make any internal or external
design and/or feature changes on or to its
products without any liability to incorporate such
changes on or to the Products.
WHAT IS NOT COVERED BY THIS
LIMITED WARRANTY
Excluded from this limited warranty and not
warranted by Olympus in any fashion, either
express, implied, or by statute, are:
(a) products and accessories not manufactured by
Olympus and/or not bearing the “OLYMPUS” brand
label (the warranty coverage for products and
accessories of other manufacturers, which may be
distributed by Olympus, is the responsibility of the
manufacturers of such products and accessories
in accordance with the terms and duration of such
manufacturers’ warranties);
(b) any Product which has been disassembled,
repaired, tampered with, altered, changed, or
modified by persons other than Olympus’s own
authorized service personnel unless repair by
others is made with the written consent of Olympus;
(c) defects or damage to the Products resulting
from wear, tear, misuse, abuse, negligence,
sand, liquids, impact, improper storage,
nonperformance of scheduled operator and
maintenance items, battery leakage, use of non“OLYMPUS” brand accessories, consumables, or
supplies, or use of the Products in combination
with non-compatible devices;
(d) software programs;
(e) supplies and consumables (including but not
limited to lamps, ink, paper, film, prints, negatives,
cables and batteries); and/or
(f) Products which do not contain a validly placed
and recorded Olympus serial number, unless they
are a model on which Olympus does not place
and record serial numbers.
EXCEPT FOR THE LIMITED WARRANTY SET
FORTH ABOVE, OLYMPUS MAKES NO AND
DISCLAIMS ALL OTHER REPRESENTATIONS,
GUARANTIES, CONDITIONS, AND
WARRANTIES CONCERNING THE
PRODUCTS, WHETHER DIRECT OR INDIRECT,
EXPRESS OR IMPLIED, OR ARISING UNDER
ANY STATUTE, ORDINANCE, COMMERCIAL
USAGE OR OTHERWISE, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY OR
EN
67
REPRESENTATION AS TO THE SUITABILITY,
DURABILITY, DESIGN, OPERATION, OR
CONDITON OF THE PRODUCTS (OR ANY
PART THEREOF) OR THE MERCHANTABILITY
OF THE PRODUCTS OR THEIR FITNESS FOR
A PARTICULAR PURPOSE, OR RELATING
TO THE INFRINGEMENT OF ANY PATENT,
COPYRIGHT, OR OTHER PROPRIETARY
RIGHT USED OR INCLUDED THEREIN.
IF ANY IMPLIED WARRANTIES APPLY AS
A MATTER OF LAW, THEY ARE LIMITED
IN DURATION TO THE LENGTH OF THIS
LIMITED WARRANTY.
SOME STATES MAY NOT RECOGNIZE
A DISCLAIMER OR LIMITATION OF
WARRANTIES AND/OR LIMITATION OF
LIABILITY SO THE ABOVE DISCLAIMERS AND
EXCLUSIONS MAY NOT APPLY.
THE CUSTOMER MAY ALSO HAVE DIFFERENT
AND/OR ADDITIONAL RIGHTS AND REMEDIES
THAT VARY FROM STATE TO STATE.
THE CUSTOMER ACKNOWLEDGES AND
AGREES THAT OLYMPUS SHALL NOT
BE RESPONSIBLE FOR ANY DAMAGES
THAT THE CUSTOMER MAY INCUR FROM
DELAYED SHIPMENT, PRODUCT FAILURE,
PRODUCT DESIGN, SELECTION, OR
PRODUCTION, IMAGE OR DATA LOSS OR
IMPAIRMENT OR FROM ANY OTHER CAUSE,
WHETHER LIABILITY IS ASSERTED IN
CONTRACT, TORT (INCLUDING NEGLIGENCE
AND STRICT PRODUCT LIABILITY) OR
OTHERWISE. IN NO EVENT SHALL OLYMPUS
BE LIABLE FOR ANY INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES OF
ANY KIND (INCLUDING WITHOUT LIMITATION
LOSS OF PROFITS OR LOSS OF USE),
WHETHER OR NOT OLYMPUS SHALL BE OR
SHOULD BE AWARE OF THE POSSIBILITY OF
SUCH POTENTIAL LOSS OR DAMAGE.
68
EN
Representations and warranties made by any
person, including but not limited to dealers,
representatives, salespersons, or agents of
Olympus, which are inconsistent or in conflict
with or in addition to the terms of this limited
warranty, shall not be binding upon Olympus
unless reduced to writing and approved by an
expressly authorized officer of Olympus.
This limited warranty is the complete and
exclusive statement of warranty which
Olympus agrees to provide with respect to the
Products and it shall supersede all prior and
contemporaneous oral or written agreements,
understandings, proposals, and communications
pertaining to the subject matter hereof.
This limited warranty is exclusively for the
benefit of the original customer and cannot be
transferred or assigned.
WHAT TO DO WHEN SERVICE IS NEEDED
The customer must transfer any image or other
data saved on a Product to another image or
data storage medium and/or remove any film
from the Product prior to sending the Product to
Olympus for service.
IN NO EVENT SHALL OLYMPUS BE
RESPONSIBLE FOR SAVING, KEEPING OR
MAINTAINING ANY IMAGE OR DATA SAVED
ON A PRODUCT RECEIVED BY IT FOR
SERVICE, OR ON ANY FILM CONTAINED
WITHIN A PRODUCT RECEIVED BY IT
FOR SERVICE, NOR SHALL OLYMPUS BE
RESPONSIBLE FOR ANY DAMAGES IN
THE EVENT ANY IMAGE OR DATA IS LOST
OR IMPAIRED WHILE SERVICE IS BEING
PERFORMED (INCLUDING, WITHOUT
LIMITATION, DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES,
LOSS OF PROFITS OR LOSS OF USE),
WHETHER OR NOT OLYMPUS SHALL BE OR
SHOULD BE AWARE OF THE POSSIBILITY OF
SUCH POTENTIAL LOSS OR IMPAIRMENT.
Package the Product carefully using ample
padding material to prevent damage in transit
and either deliver it to the Authorized Olympus
Dealer that sold you the Product or ship it
postage prepaid and insured to any of our
Olympus Service Centers.
When returning Products for service, your
package should include the following:
1 Sales receipt showing date and place of
purchase.
2 Copy of this limited warranty bearing the
Product serial number corresponding to the
serial number on the Product (unless it is a
model on which Olympus does not place and
record serial numbers).
3 A detailed description of the problem.
4 Sample prints, negatives, digital prints (or files on
disk) if available and related to the problem.
When service is completed, the Product will be
returned to you postage prepaid.
WHERE TO SEND PRODUCT FOR
SERVICE
See “WORLDWIDE WARRANTY” for the
nearest service center.
INTERNATIONAL WARRANTY SERVICE
International warranty service is available under
this warranty.
For customers in Europe
“CE” mark indicates that this product complies
with the European requirements for safety,
health, environment and customer protection.
“CE” mark cameras are intended for sales in
Europe.
This symbol [crossed-out wheeled bin WEEE
Annex IV] indicates separate collection of waste
electrical and electronic equipment in the EU
countries.
Please do not throw the equipment into the
domestic refuse.
Please use the return and collection systems
available in your country for the disposal of this
product.
This symbol [crossed-out wheeled bin Directive
2006/66/EC Annex II] indicates separate
collection of waste batteries in the EU countries.
Please do not throw the batteries into the
domestic refuse. Please use the return and
collection systems available in your country for
the disposal of the waste batteries.
Provisions of warranty
1 If this product proves to be defective, although it
has been used properly (in accordance with the
written Handling Care and Operating instructions
supplied with it), during the applicable national
warranty period and has been purchased from
an authorized Olympus distributor within the
business area of Olympus Europa Holding GmbH
as stipulated on the website: http://www.olympus.
com this product will be repaired, or at Olympus’s
option replaced, free of charge. To claim under
this warranty the customer must take the product
before the end of the applicable national warranty
period to the dealer where the product was
purchased or any other Olympus service station
within the business area of Olympus Europa
Holding GmbH as stipulated on the website:
http://www.olympus.com. During the one year
period of the World Wide Guarantee the customer
may turn the product in at any Olympus service
station. Please notice that not in all countries
such Olympus service station exists.
2 The customer shall transport the product to the
dealer or Olympus authorized service station
at his own risk and shall be responsible for any
costs incurred in transporting the product.
Provisions of Guarantee
1 “OLYMPUS IMAGING CORP., Shinjuku
Monolith, 2-3-1 Nishi-Shinjuku, Shinjuku-ku,
Tokyo 163-0914, Japan grants a one year World
Wide Guarantee. This worldwide Guarantee
must be presented at an Olympus authorized
repair service station before any repair can
be made under conditions of this Guarantee.
This Guarantee is valid only if the Guarantee
Certificate and proof of purchase are presented
at the Olympus repair service station. Please note
that this Guarantee is in addition to and does not
affect the customer’s legal warranty rights under
the applicable national legislation governing the
sale of consumer goods mentioned above.
2 This Guarantee does not cover the following
and the customer will be required to pay repair
charge, even for defects occurring within the
Guarantee period referred to above.
a. Any defect that occurs due to mishandling
(such as an operation performed that is not
mentioned in the Handling Care or other
sections of the instructions, etc.)
b. Any defect that occurs due to repair,
modification, cleaning, etc. performed by
anyone other than Olympus or an Olympus
authorized service station.
c. Any defect or damage that occurs due to
transport, a fall, shock, etc. after purchase of
the product.
d. Any defect or damage that occurs due to fire,
earthquake, flood damage, thunderbolt, other
natural disasters, environmental pollution and
irregular voltage sources.
e. Any defect that occurs due to careless or
improper storage (such as keeping the
product under conditions of high temperature
and humidity, near insect repellents such as
naphthalene or harmful drugs, etc.), improper
maintenance, etc.
f. Any defect that occurs due to exhausted
batteries, etc.
g. Any defect that occurs due to sand, mud, etc.
entering the inside of the product casing.
h. When the Guarantee Certificate is not
returned with the product.
i. When any alterations whatsoever are made to
the Guarantee Certificate regarding the year,
month and date of purchase, the customer’s
name, the dealer’s name, and the serial
number.
j. When proof of purchase is not presented with
this Guarantee Certificate.
3 This Guarantee applies to the product only; the
Guarantee does not apply to any other accessory
equipment, such as the case, strap, lens cap and
batteries.
4 Olympus’s sole liability under this Guarantee shall
be limited to repairing or replacing the product.
Any liability under the Guarantee for indirect
or consequential loss or damage of any kind
incurred or suffered by the customer due to a
defect of the product, and in particular any loss
or damage caused to any lenses, films, other
equipment or accessories used with the product
or for any loss resulting from a delay in repair or
loss of data, is excluded. Compelling regulations
by law remain unaffected by this.
EN
69
Notes regarding Guarantee maintenance
1 This Guarantee will only be valid if the Guarantee
Certificate is duly completed by Olympus or an
authorized dealer or other documents contain
sufficient proof. Therefore, please make sure
that your name, the name of the dealer, the
serial number and the year, month and date of
purchase are all completed or the original invoice
or the sales receipt (indicating the dealer’s
name, the date of purchase and product type) is
attached to this Guarantee Certificate. Olympus
reserves the right to refuse free-of-charge service
if neither Guarantee Certificate is completed
nor the above document is attached or if the
information contained in it is incomplete or
illegible.
2 Since this Guarantee Certificate will not be reissued, keep it in a safe place.
* Please refer to the list on the web site: http://
www.olympus.com for the authorized international
Olympus service network.
For customers in Asia
Provisions of warranty
1 lf this product proves to be defective, although it
has been used properly (in accordance with the
written Handling Care and Operating instructions
supplied with it), during a period of up to one
year from the date of purchase this product will
be repaired, or at Olympus’s option replaced,
free of charge. To claim under warranty the
customer must take the product and this Warranty
certificate before the end of the one year warranty
period to the dealer where the product was
purchased or any Olympus authorized service
station listed in the instructions and request the
necessary repairs.
2 The customer shall transport the product to the
dealer or Olympus authorized service station
at his own risk and shall be responsible for any
costs incurred in transporting the product.
3 This warranty does not cover the following
and the customer will be required to pay repair
charge, even for defects occurring within the one
year period referred to above.
a. Any defect that occurs due to mishandling
(such as an operation performed that is not
mentioned in the Handling Care or other
sections of the instructions, etc.)
b. Any defect that occurs due to repair,
modification, cleaning, etc. performed by
anyone other than Olympus or an Olympus
authorized service station.
c. Any defect or damage that occurs due to
transport, a fall, shock, etc. after purchase of
the product.
d. Any defect or damage that occurs due to fire,
earthquake, flood damage, thunderbolt, other
natural disasters, environmental pollution and
irregular voltage sources.
70
EN
e. Any defect that occurs due to careless or
improper storage (such as keeping the
product under conditions of high temperature
and humidity, near insect repellents such as
naphthalene or harmful drugs, etc.), improper
maintenance, etc.
f. Any defect that occurs due to exhausted
batteries, etc.
g. Any defect that occurs due to sand, mud, etc.
entering the inside of the product casing.
h. When this Warranty Certificate is not returned
with the product.
i. When any alterations whatsoever are made
to the Warranty Certificate regarding the year,
month and date of purchase, the customer’s
name, the dealer’s name, and the serial
number.
j. When proof of purchase is not presented with
this Warranty Certificate.
4 This Warranty applies to the product only; the
Warranty does not apply to any other accessory
equipment, such as the case, strap, lens cap and
batteries.
5 Olympus’ sole liability under this warranty shall be
limited to repairing or replacing the product and
any liability for indirect or consequential loss or
damage of any kind incurred or suffered by the
customer due to a defect in the product, and in
particular any loss or damage caused to any film
or lenses or other equipment or accessories used
with the product or for any loss resulting from
delay in repair, is excluded.
Notes;
1 This Warranty is in addition to and does not affect
the customer’s statutory right.
2 lf you have any queries regarding this Warranty,
call any of the Olympus authorized service
stations listed in the instructions.
Notes regarding warranty maintenance
1 This Warranty will only be valid if the Warranty
Certificate is duly completed by Olympus or the
dealer. Make sure that your name, the name of
the dealer, the serial number and the year, month
and date of purchase are all completed.
2 Since this Warranty Certificate will not be
re-issued, keep it in a safe place.
3 Any request for repair by a customer in same
country where the product was purchased shall
be subject to the terms of the warranty issued by
the Olympus distributor in that country. Where
the local Olympus distributor does not issue a
separate warranty or where the customer is not in
the country where the product was purchased the
terms of this worldwide warranty shall apply.
4 Where applicable, this Warranty is valid
worldwide. The Olympus authorized service
stations listed in this Warranty will gladly honor it.
* Please refer to the appended list for the
authorized international Olympus service
network.
Disclaimer of Warranty
Olympus makes no representations or
warranties, either expressed or implied, by or
concerning any content if these written materials
or software, and in no event shall be liable
for any implied warranty of merchantability or
fitness for any particular purpose or for any
consequential, incidental or indirect damages
(including but not limited to damages for loss
of business profits, business interruption and
loss of business information) arising from the
use of inability to use these written materials or
software. Some states do not allow the exclusion
or limitation of liability for consequential or
incidental damages, so the above limitations
may not apply to you.
Trademarks
• IBM is a registered trademark of International
Business Machines Corporation.
• Microsoft and Windows are registered trademarks
of Microsoft Corporation.
• Macintosh is a trademark of Apple Inc.
• The SDHC logo is a trademark.
• All other company and product names are
registered trademarks and/or trademarks of their
respective owners.
• The standards for camera file systems referred to
in this manual are the “Design rule for Camera File
system/DCF” standards stipulated by the Japan
Electronics and Information Technology Industries
Association (JEITA).
THIS PRODUCT IS LICENSED UNDER THE
AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NONCOMMERCIAL USE
OF A CONSUMER TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD (“AVC
VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED TO PROVIDE AVC
VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG
LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
EN
71
SPECIFICATIONS
Camera
Product type
: Digital camera (for shooting and displaying)
Recording system
Still pictures
: Digital recording, JPEG (in accordance with Design rule for Camera File system (DCF))
Applicable standards : Exif 2.2, Digital Print Order Format (DPOF), PRINT Image Matching III, PictBridge
Sound with still
pictures
: Wave format
Movie
: MPEG-4AVC./H.264
Memory
: Internal memory
SD memory card
SDHC memory card
No. of effective pixels
: 14,000,000 pixels
Image pickup device
: STYLUS-9010/μ-9010: 1/2.33” CCD (primary color filter)
STYLUS-7040/μ-7040: 1/2.3” CCD (primary color filter)
STYLUS-5010/μ-5010: 1/2.33” CCD (primary color filter)
Lens
: STYLUS-9010/μ-9010: Olympus lens 5.0 to 50.0 mm, f3.2 to 5.9
(equivalent to 28 to 280 mm on a 35 mm camera)
STYLUS-7040/μ-7040: Olympus lens 5.0 to 35.0 mm, f3.0 to 5.9
(equivalent to 28 to 196 mm on a 35 mm camera)
STYLUS-5010/μ-5010: Olympus lens 4.7 to 23.5 mm, f2.8 to 6.5
(equivalent to 26 to 130 mm on a 35 mm camera)
Photometric system
: Digital ESP metering, spot metering system
Shutter speed
: 4 to 1/2000 sec.
Shooting range
: STYLUS-9010/μ-9010: 0.5 m (1.6 ft.) to (W), 1.0 m (3.3 ft.) to (T) (normal)
0.1 m (0.3 ft.) to (W), 0.9 m (3.0 ft.) to (T) (macro mode)
0.01 m (0.4 ft.) to 0.5 m (1.6 ft.) (W only) (super macro mode)
STYLUS-7040/μ-7040: 0.7 m (2.3 ft.) to (normal)
0.1 m (0.3 ft.) to (W), 0.6 m (2.0 ft.) to (T) (macro mode)
0.02 m (0.07 ft.) to 0.7 m (2.3 ft.) (W only) (super macro mode)
STYLUS-5010/μ-5010: 0.6 m (2.0 ft.) to (W), 1.0 m (3.3 ft.) to (T) (normal)
0.15 m (0.5 ft.) to (W), 0.6 m (2.0 ft.) to (T) (macro mode)
0.07 m (0.2 ft.) to 0.6 m (2.0 ft.) (f=8.3 (fixed)) (super macro mode)
Monitor
: STYLUS-9010/μ-9010: 2.7” TFT color LCD display, 230,000 dots
STYLUS-7040/μ-7040: 3.0” TFT color LCD display, 230,000 dots
STYLUS-5010/μ-5010: 2.7” TFT color LCD display, 230,000 dots
Connector
: DC-IN jack, USB connector, A/V OUT jack (Multi-connector)/
HDMI micro connector (type D)
Automatic calendar
system
: 2000 up to 2099
Operating environment
72
EN
Temperature
: 0 °C to 40 °C (32 °F to 104 °F) (operation)/
-20 °C to 60 °C (-4 °F to 140 °F) (storage)
Humidity
: 30 % to 90 % (operation)/10 % to 90 % (storage)
Power supply
: One Olympus lithium ion battery (LI-50B (STYLUS-9010/μ-9010)/LI-42B/LI-40B
(STYLUS-7040/μ-7040/STYLUS-5010/μ-5010)) or separately sold AC adapter
Dimensions
: STYLUS-9010/μ-9010: 94.0 mm (W) × 57.6 mm (H) × 31.1 mm (D)
(3.7 × 2.3 × 1.2 in.) (excluding protrusions)
STYLUS-7040/μ-7040: 94.5 mm (W) × 55.5 mm (H) × 25.9 mm (D)
(3.7 × 2.2 × 1.0 in.) (excluding protrusions)
STYLUS-5010/μ-5010: 94.7 mm (W) × 55.8 mm (H) × 19.9 mm (D)
(3.7 × 2.2 × 0.8 in.) (excluding protrusions)
Weight
: STYLUS-9010/μ-9010: 171 g (6.0 oz) (including battery and card)
STYLUS-7040/μ-7040: 144 g (5.1 oz) (including battery and card)
STYLUS-5010/μ-5010: 126 g (4.4 oz) (including battery and card)
Lithium ion battery (LI-42B)
Product type
: Lithium ion rechargeable battery
Standard voltage
: DC 3.7 V
Standard capacity
: 740 mAh
Battery life
: Approx. 300 full charges (varies on usage)
Operating environment
Temperature
: 0 °C to 40 °C (32 °F to 104 °F) (charging)/
-10 °C to 60 °C (14 °F to 140 °F) (operation)/
-20 °C to 35 °C (-4 °F to 95 °F) (storage)
Dimensions
: 31.5 mm (W) × 39.5 mm (H) × 6.0 mm (D) (1.2 × 1.5 × 0.2 in.)
Weight
: Approx. 15 g (0.5 oz)
Lithium ion battery (LI-50B)
Product type
: Lithium ion rechargeable battery
Model No.
: LI-50BA/LI-50BB
Standard voltage
: DC 3.7 V
Standard capacity
: 925 mAh
Battery life
: Approx. 300 full charges (varies on usage)
Operating environment
Temperature
: 0 °C to 40 °C (32 °F to 104 °F) (charging)/
-10 °C to 60 °C (14 °F to 140 °F) (operation)/
-10 °C to 35 °C (14 °F to 95 °F) (storage)
Dimensions
: 34.4 mm (W) × 40.0 mm (H) × 7.0 mm (D) (1.4 × 1.6 × 0.3 in.)
Weight
: Approx. 20 g (0.7 oz)
USB-AC adapter (F-2AC)
Model No.
: F-2AC-1A/F-2AC-2A/F-2AC-1B/F-2AC-2B
Power requirements
: AC 100 to 240 V (50/60 Hz)
Output
: DC 5 V, 500 mA
Operating environment
Temperature
: 0 °C to 40 °C (32 °F to 104 °F) (operation)/
-20 °C to 60 °C (-4 °F to 140 °F) (storage)
Dimensions
: 50.0 mm (W) × 54.0 mm (H) × 22.0 mm (D) (2.0 × 2.1 × 0.9 in.)
Weight
: Approx. 46.0 g (1.6 oz) (F-2AC-1A)/Approx. 42.0 g (1.5 oz) (F-2AC-2A)/
Approx. 44.0 g (1.6 oz) (F-2AC-1B)/Approx. 40.0 g (1.4 oz) (F-2AC-2B)
Design and specifications subject to change without notice.
HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
EN
73
VN688501
Download PDF