technical manual

IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
AUTHORS
DATE
REFERENCE
V. Bafour
23/01/2008
D0503022
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 2/12
TABLE OF CONTENTS
1.
INTRODUCTION ....................................................................................................................................... 3
2.
SAFETY ....................................................................................................................................................... 3
2.1
2.2
2.3
3.
OVERVIEW ................................................................................................................................................ 4
3.1
3.2
4.
SYNOPSIS .............................................................................................................................................. 5
INSTALLATION......................................................................................................................................... 5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.9.1
5.9.2
6.
REFERENCES ......................................................................................................................................... 4
FEATURES ............................................................................................................................................. 4
DESCRIPTION ........................................................................................................................................... 5
4.1
5.
OPERATING REQUIREMENTS ................................................................................................................. 3
POWER SOURCE .................................................................................................................................... 3
MAINTENANCE...................................................................................................................................... 3
INSTALLATION PROCEDURE .................................................................................................................. 5
LIST OF SUPPLIES .................................................................................................................................. 6
WALL ATTACHMENT............................................................................................................................. 6
WALLBOARD CONFIGURATION.............................................................................................................. 6
WALLBOARD CONNECTIONS ................................................................................................................. 7
COMMISSIONING ............................................................................................................................. 7
COMMISSIONING PROCEDURE ............................................................................................................... 7
POWER ON ............................................................................................................................................ 7
IP SETTING MANAGEMENT ................................................................................................................... 7
First Commissioning ....................................................................................................................... 8
Setting Change .............................................................................................................................. 11
TROUBLESHOOTING ............................................................................................................................ 12
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 3/12
1. INTRODUCTION
The Alcatel-Lucent 4x16 & 6x16 character IP wallboards are wallboards that include 4 and 6
color lines of 16 alphanumeric characters.
2. SAFETY
Please carefully read this section before using the wallboard.
2.1 Operating Requirements
Do not install the wallboard in any location exposed to direct sunlight or excessive
heat. Maximum operating temperature = 40°C.
Do not subject the wallboard to any condensation or water spray.
Do not install the wallboard in any environment where pollution exceeds level 2.
2.2 Power Source
The wallboard must be installed by a qualified staff.
The power socket must be installed near the wallboard and easily reachable.
Otherwise, a quickly-accessible shutoff device must be integrated into the fixed
installation.
2.3 Maintenance
Unplug the wallboard before any maintenance operation. Do not use any liquid
cleaners or sprays. Use a wet cloth.
Do not disassemble the wallboard. There is no user-replaceable part within the
wallboard. Any improper reassembly could cause injuries due to electric shocks.
If any maintenance or repair operation is required, supply the wallboard to a qualified
staff.
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 4/12
3. OVERVIEW
Each wallboard character consists of a 7-row x 5-column LED matrix.
3.1 References
P3540400 : 4x16 wallboard (Four 16-character lines)
P3540600 : 6x16 wallboard (Six 16-character lines)
3.2 Features
Compatible with 3BH11616AA and 3BH11617 wallboard’s protocol.
IP connection: 10Base-T Ethernet.
Display modes: Steady, flashing.
Display colors: Red, green, orange, yellow, ochre.
Buzzer.
Power Supply: 100-240V; 3.15-1.5A; 50/60Hz
Installation Class II.
Equipment can be connected to TT or TN supply network only.
Class-I equipment connected through IEC83-compliant 2P+T power plug. The socket
that supplies power to the wallboard must be grounded.
Dimensions
P3540400 (4 x 16) : 696 x 312 x 61.
P3540600 (6 x 16) : 696 x 408 x 61.
Weight
P3540400 (4 x 16) : 4,2 Kg.
P3540600 (6 x 16) : 5.7 Kg.
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 5/12
4. DESCRIPTION
The wallboard has a 10Base-T Ethernet input used to receive display controls.
The wallboard is connected to the same local Ethernet network as the CSS control panel
(managed from the Wall Board Manager application).
4.1 Synopsis
PC CCS - WBM
Wallboard
10Mbit Ethernet
5. INSTALLATION
5.1 Installation Procedure
1. Check the list of supplies.
2. Complete the wall attachment.
3. Complete the configuration (micro-switchs ).
4. Complete the connections.
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 6/12
5.2 List of Supplies
Qty
1
1
1
1
1
Reference
P2540400
or
P2340600
C1800127
C1800125
C2000010
C2130008
Designation
4x16 wallboard
6x16 wallboard
Female mains plug
Screw-on 4-way female connector
Crossed Ethernet cable
Mounting foot
5.3 Wall Attachment
The wallboard is attached with the Mounting foot
Distance between centres: 310mm
Screws Ø 3mm
Outdistance minimum ceiling 200mm.
5.4 Wallboard Configuration
The wallboard operating mode is set up using SW1-SW8 micro-switchs that can be accessed
through an opening on the top panel of the wallboard.
Micro-switchs are read when the wallboard is started: All Micro-switchs must be at Off
SW8
SW1
ON
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 7/12
5.5 Wallboard Connections
Connections are made to the top panel of the wallboard. The Ethernet cable from the HUB is
connected to the RJ45 Ethernet plug directly. . Use the crossed Ethernet cable when the
wallboard is connected to a PC directly.
To comply with EMC rules, the cable type must be FTP or STP.
1234
Main supply
Ethernet plug
V24/Current Loop Connection
5.6 COMMISSIONING
5.7 Commissioning Procedure
1. Turn the power on.
2. Manage the IP settings.
5.8 Power On
When powered on, the wallboard is started. Before the normal operating mode, there is an
identification stage followed by a self-test. In the identification stage, the odd-numbered lines
show the wallboard software version, and the second line shows the wallboard IP address.
The self-test activates every wallboard dot, line after line, in both basic colors: red and green.
This allows visually checking that every wallboard dot works properly.
5.9 IP Setting Management
IP settings can be accessed from a PC. A Web browser can be used to connect to the
wallboard’s IP address. At power on, the wallboard’s IP address is displayed in the second
line.
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 8/12
5.9.1 First Commissioning
Follow the procedure below:
1. Turn the power on.
2. Connect the wallboard to the PC directly, using the crossed Ethernet cable as supplied.
Crossed Ethernet
Wallboard
3. Change the PC network settings to an IP address compatible with the wallboard’s IP
address, e.g. 10.0.0.1 if the wallboard is set to its default address 10.0.0.88.
Windows 98 example - Change network neighborhood properties:
>
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 9/12
Windows NT example:
>
4. With a Web browser, connect to the wallboard’s IP address (http://10.0.0.88 for the
default address) to open the wallboard’s setup page.
5. Enter the new settings and validate. To apply the new settings, the wallboard will be reset
a few seconds after validation.
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 10/12
Internet Explorer example:
Address : Wallboard address (default: 0).
Baud rate : Output rate of the serial connection (default: 9,600).
Buzzer duration : Duration of the buzzer in seconds (default: 3).
IP address : IP address (default: 10.0.0.88).
Net mask : Sub-network mask (default: 255.0.0.0).
Gateway : Gateway address. To be filled in to access the settings from another
network (default: blank).
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 11/12
5.9.2 Setting Change
To change the settings of a wallboard in operation, proceed as follows:
1. Use a PC connected to the same network as the wallboard.
Wallboard
10Mbit Ethernet
2. Using a Web browser, connect to the wallboard’s IP address.
3. Change the settings. Entering new settings causes the wallboard to be reset a few seconds
after validation.
IP WALLBOARD
4 x 16 and 6 x 16 digits
TECHNICAL
MANUAL
D0503022
23/01/2008
Page 12/12
6. TROUBLESHOOTING
This section will be extended as issues are found and solutions provided. Please feel free to
give us your feedback.
Ethernet Connection: Can not communicate with the wallboard
Cause
The Web browser goes through a proxy server to connect to the Internet.
Solution
In the browser settings, remove the proxy server or specify that the proxy server
should not be used to connect to the wallboard’s IP address.
Error in the sub-network mask or gateway address.
Turn the wallboard off, install micro-switch SW4, turn the wallboard back on, and
remove micro-switch SW4. This allows resetting the wallboard to its default
parameters (IP Address: 10.0.0.88). Then, follow the first commissioning
instructions.
Download PDF