HomeWorks Remote Power Modules (RPMs) Spec Submittal Part

product specifications
369547d
10.27.15
Remote Power Modules
Remote Power Modules (RPMs) are used to
control lighting, motor, and fan loads. There are
several different models of RPMs. Each model
controls specific load types. The RPMs are
mounted in remote power panels.
All RPMs must be connected to a module
interface housed within the same panel
enclosure. RPMs within an enclosure are
connected to the module interface using a
Lutron-provided harness. To minimize the effects
of single power supply failure, each RPM is
powered by its own internal power supply.
Model Numbers
Model
Voltage
Description
HW-RPM-4A-120
120 V~
Adaptive Dimming Module
HW-RPM-4A-230
220–240 V~
Adaptive Dimming Module
HW-RPM-4E-230-CE
220–240 V~
ELV Dimming Module
HW-RPM-4FSQ-120
120 V~
Quiet Fan Speed Control Module
HW-RPM-4J-120
120 V~
Adaptive Dimming Module
HW-RPM-4M-120
120 V~
Motor Control Module
HW-RPM-4M-230
220–240 V~
Motor Control Module
HW-RPM-4R
100–277 V~
Power Relay Module
HW-RPM-4U-120
120 V~
Dimming Module
HW-RPM-4U-230-CE
220–240 V~
Dimming Module
HW-RPM-4U-240
240 V~
Dimming Module
www.lutron.com
1
Technical support: U.S.A.: 800.523.9466
Europe: +44.(0)20.7680.4481
product specifications
369547d
10.27.15
Remote Power Modules
Specifications
Model Numbers
Power
HW-RPM-4A-120, HW-RPM-4A-230, HW-RPM-4E-230-CE, HW-RPM-4FSQ-120, HW-RPM-4J-120,
HW-RPM-4M-120, HW-RPM-4M-230, HW-RPM-4R, HW-RPM-4U-120, HW-RPM-4U-230-CE,
HW-RPM-4U-240
• HW-RPM-4A-120, HW-RPM-4FSQ-120, HW-RPM-4J-120, HW-RPM-4M-120, HW-RPM-4U-120:
120 V~ 50 / 60 Hz
• HW-RPM-4A-230, HW-RPM-4M-230, HW-RPM-4U-230-CE, HW-RPM-4U-240:
220–240 V~ 50 / 60 Hz
• HW-RPM-4R: 100–277 V~ 50 / 60 Hz
Number of Outputs
4
Regulatory Approvals UL®, CSA, NOM
Environment
Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0 to 90% humidity, non-condensing.
Indoor use only.
Cooling
Passive cooling.
Heat Generated
• HW-RPM-4A-120, HW-RPM-4A-230, HW-RPM-4E-230-CE, HW-RPM-4J-120: 90 BTUs per hour.
Fully Loaded
• HW-RPM-4FSQ-120, HW-RPM-4M-120, HW-RPM-4M-230, HW-RPM-4R: 18 BTUs per hour.
• HW-RPM-4U-120, HW-RPM-4U-230-CE, HW-RPM-4U-240: 70 BTUs per hour.
Line-Voltage
Separate line-voltage feeds at the DIN rail terminal blocks for each RPM. Terminal blocks should be
Connections
tightened to 3.5 in-lb to 5.0 in-lb (0.40 N•m to 0.57 N•m).
Low-Voltage
Communication harness (included).
Communications
Wiring
Terminal blocks will accept one 18 AWG to 10 AWG (1.0 mm2 to 6.0 mm2) wire or two
18 AWG to 16 AWG (1.0 mm2 to 1.5 mm2) wires.
• HW-RPM-4M-120, HW-RPM-4M-230, HW-RPM-4R: Require the installation of four additional gray
terminal blocks (included) and three additional black terminal blocks (included) to be mounted on to
the DIN rail assembly.
• HW-RPM-4R gray terminal blocks accept one 18 AWG to 8 AWG (1.0 mm2 to 10 mm2) wire or two
16 AWG to 12 AWG (1.5 mm2 to 4.0 mm2) wires.
Addressing
Manual rotary switch. Counts as 1 of 8 RPM addresses per module interface.
Diagnostics
LED provided to indicate proper communications with module interface.
ESD Protection
Meets or exceeds the IEC 61000-4-2 standard.
Surge Protection
Meets or exceeds ANSI/IEEE standard c62.41.
Air Gap
• HW-RPM-4U-120, HW-RPM-4U-230-CE HW-RPM-4A-120, HW-RPM-4A-230, HW-RPM-4J-120,
HW-4FSQ-120, HW-RPM-4M-230: Provided when all four circuits are off.
• HW-RPM-4R: Individual output airgap provided when each circuit is off.
Fail-Safe Operation
Rotary switch on the RPM allows for manual operation of each load.
Dimensions
37⁄8 in (99 mm) wide × 7 in (178 mm) high
Lamp Buzz
Lamp debuzzing coils (Lutron® model HW-HIFC-10-2, LDC-10-TCP, LDC-16-TCP) are available from
Lutron to reduce lamp filament buzzing.
Interface Suppression EMI/RFI suppression circuitry
Warranty
www.lutron.com/TechnicalDocumentLibrary/Warranty.pdf
www.lutron.com/TechnicalDocumentLibrary/Intl_Warranty.pdf
www.lutron.com
2
Technical support: U.S.A.: 800.523.9466
Europe: +44.(0)20.7680.4481
product specifications
369547d
10.27.15
Remote Power Modules
Load Type, Rating, and Capacity
Model
Voltage/
Frequency
HW-RPM-4A-120
120 V~
50/60 Hz
HW-RPM-4A-230
220–240 V~
50/60 Hz
V~
HW-RPM-4E-230-CE 220–240
50/60 Hz
HW-RPM-4J-120
120 V~
50/60 Hz
HW-RPM-4FSQ-120
120 V~
50/60 Hz
HW-RPM-4M-120
120 V~
50/60 Hz
HW-RPM-4M-230
220–240 V~
50/60 Hz
HW-RPM-4R
100–277 V~
50/60 Hz
HW-RPM-4U-120
120 V~
50/60 Hz
V~
HW-RPM-4U-230-CE 220–240
50/60 Hz
HW-RPM-4U-240
1
2
3
4
5
6
7
8
220–240 V~
50/60 Hz
Load Types1
Minimum Maximum Load Per:
Load
Output
Module
INC, MLV, ELV,
NCC, F2W
10 W
10 A
Maximum
BTUs / Hour Technology
16 A
LED2
INC, MLV, ELV,
NCC
LED2
10 W
INC, ELV3
10 W
10 A
16 A
INC, MLV, ELV,
NCC, F2W
10 W
6A
16 A
See note 2
8A
13 A
90
See note 2
LED2
RTISS-TETM6
See note 2
Fan Motor4
0.25 A
2A
INC
Motor
(Bi-directional)
INC
Motor
(Bi-directional)
Lighting
Motor
INC5, MLV5,
NCC, F2W, SFL
LED2
INC, MLV,
NCC, SFL
LED2
INC, MLV,
NCC,SFL
LED2
0A
3A
5 A (1/4 HP)
0A
Quiet control
circuitry
8A
16 A
18
1.5 A
5 A (1/4 HP)
16 A
0A
16 A
(1/3 HP)
64 A
25 W
16 A
16 A
Mechanical
interlocked
relays
Softswitch®7
See note 2
40 W
10 A
13 A
See note 2
40 W
16 A
70
RTISS
Equipped®8
16 A
See note 2
For higher wattages or for load types other than those listed, a power booster or interface is required. For more details, refer to the
HomeWorks® software.
NOTICE: To avoid the risk of equipment damage and for specific LED lamp / fixture compatibility, refer to the LED Product Selection
tool at www.lutron.com/ledtool. For general information about minimum/maximum load requirements and LED loads refer to
Application Note #487 - Minimum and Maximum loads for LED and CFL lamps / fixtures. Please note that LED is not currently a
supported load type of UL® 508. As a result, this UL® listing does not guarantee compatibility between the remote power module and
connected LED loads.
Only use with ELV transformers. If used with MLV transformers, the module may be damaged and the warranty will be void.
Control up to 4 ceiling fans (1 per circuit). Do not use to control fans that have integrated fan speed controls (i.e., fan with a remote control).
This module may hum or buzz when at medium-high fan setting. Do not connect to lighting loads. Damage to the module could result.
In rare cases, incandescent lamps and MLV transformers will “buzz” or “hum”. The HW-HIFC-10-2 filter choke assembly reduces this hum.
The filter choke assembly can be installed in place of module 8 in an HWI-PNL-8 remote power panel.
RTISS-TETM: (Real-Time Illumination Stability System-Trailing Edge). Same as RTISS ®, but operates on the trailing edge of the A/C sine wave.
This allows for true instantaneous voltage compensation.
Softswitch®: Lutron® Softswitch® circuitry prevents the relay contacts from arcing. Even when fully loaded, the arc reduction extends a relay’s
average rated life to more than 1,000,000 on/off cycles.
RTISS Equipped® (Real-Time Illumination Stability System). This Lutron® filter circuit technology compensates for incoming line-voltage
variations, such as changes in Root Mean Square (RMS) voltage, frequency shifts, harmonics, and line noise.
www.lutron.com
3
Technical support: U.S.A.: 800.523.9466
Europe: +44.(0)20.7680.4481
product specifications
369547d
10.27.15
Remote Power Modules
Dimensions
For information on mounting an RPM
within an existing LiteTouch® panel,
please refer to the installation guide
of the Dimming & Switching Ready
Retrofit Subplate at www.lutron.com
Measurements shown as: in (mm)
37⁄8 (99)
7 (178)
Mounting
HWAP-2S, HWBP-2S
HWI-PNL-5
HWI-PNL-8 (shown), HWAP-8D, HWBP-8D
LiteTouch is a registered trademark of Savant.
www.lutron.com
4
Technical support: U.S.A.: 800.523.9466
Europe: +44.(0)20.7680.4481
product specifications
369547d
10.27.15
Remote Power Modules
Wiring
HW-RPM-4A-120, HW-RPM-4A-230, HW-RPM-4E-230-CE, HW-RPM-4FSQ-120, HW-RPM-4J-120,
HW-RPM-4U-120, HW-RPM-4U-230-CE, HW-RPM-4U-240
Removable Bypass Jumpers
Red 1
Red 2
Red 3
Red 4
Black
White
DH1
DH2
DH3
DH4
120 V~ or 220–240 V~ Hot
Neutral from Distribution Panel
N1
N2
N3
N4
Rotary Address
Switch
4-Pin connector for
Module Interface
Assembly Harness
HW-RPM-4M-120, HW-RPM-4M-230
Input 120–240 V~ from Distribution Panel (20 A)
Input Neutral from Distribution Panel
Raise
Lower
M
Raise
Red 1
Yellow 1
Red 2
Yellow 2
Red 3
Yellow 3
Red 4
Yellow 4
Black
White
R1
L1
R2
L2
R3
L3
R4
L4
H
N
N
N
N
N
Lower
M
Rotary Address
Switch
4-Pin connector for
Module Interface
Assembly Harness
HW-RPM-4R
Input 100–277 V~ from Distribution Panel
Input Neutral from Distribution Panel
www.lutron.com
SH1
H1
N1
SH2
H2
N2
SH3
H3
N3
SH4
H4
N4
Red 1
Black 1
Control Power
Control Neutral
Red 2
Black 2
Red 3
Black 3
Red 4
Black 4
5
Rotary Address
Switch
4-Pin connector for
Module Interface
Assembly Harness
Technical support: U.S.A.: 800.523.9466
Europe: +44.(0)20.7680.4481
product specifications
369547d
10.27.15
Remote Power Modules
Address Switch Position
Diagnostic LED Status
HW-RPM-4A-120, HW-RPM-4A-230,
HW-RPM-4E-230-CE, HW-RPM-4FSQ-120,
HW-RPM-4J-120, HW-RPM-4R,
HW-RPM-4U-120, HW-RPM-4U-230-CE,
HW-RPM-4U-240:
HW-RPM-4A-120, HW-RPM-4A-230,
HW-RPM-4E-230-CE, HW-RPM-4FSQ-120,
HW-RPM-4J-120, HW-RPM-4R,
HW-RPM-4U-120, HW-RPM-4U-230-CE,
HW-RPM-4U-240:
Position
0
1–8
9A
9B
9C
9D
9E
9F
Module Output/Purpose
All outputs OFF
Address for normal operation
Not used
Output 1 ON; Use for temporary lighting and
zone testing
Output 2 ON; Use for temporary lighting and
zone testing
Output 3 ON; Use for temporary lighting and
zone testing
Output 4 ON; Use for temporary lighting and
zone testing
All outputs ON; Use for temporary lighting and
zone testing
LED Status
Off
1 blink per second
(“Heartbeat”)
1 blink per 7 seconds
(“Lighthouse”)
Not communicating with
processor:
• Open control harness
• Module set on invalid or
diagnostic address
• System not properly configured
or addressed in HomeWorks®
software
4 blinks; pause; repeat Module in manual override
10 blinks per second Zone error on one or more
outputs
HW-RPM-4M, HW-RPM-4M-230:
Position
0
1–8
9 A–D
9E
9F
Zone Diagnostic LED Status
Module Output/Purpose
All relays OFF
Address for normal operation
Not used: All outputs OFF
All raise relays ON; Use for directional motor
testing
All lower relays ON; Use for directional motor
testing
HW-RPM-4E-230-CE, HW-RPM-4A-120,
HW-RPM-4J-120, HW-RPM-4A-230 only:
Zone LED Status Load Status Description
Off
OFF
Normal; Load Off
Continuously on ON
Incandescent/electronic
dimming
1 blink per
ON
Magnetic dimming
second
Error Codes
1 blink; pause;
OFF
Load short circuit1
repeat
2 blinks; pause;
OFF
Inductive load2
repeat
3 blinks; pause;
ON Full
Shorted component3
repeat
4 blinks; pause;
OFF
Overload1
repeat
10 blinks per
All outputs
Multiple errors4
second
OFF
1
2
Enlarged view of Address Switch
www.lutron.com
Possible Cause
No power or defective module
Normal operation
3
4
6
Locate and repair fault. Cycle power to RPM.
Check software configuration. MLV load detected with ELV
software setting.
Replace RPM. Internal device (FET) shorted.
Multiple errors exist on this output. The relay has opened to
protect the modules and all 4 outputs will be off.
Technical support: U.S.A.: 800.523.9466
Europe: +44.(0)20.7680.4481
Download PDF