HoyaiLink-in-a-box – Setup

HoyaiLink-in-a-box – Setup
Summary
Requirements........................................................................................................................ 2
Part I – HoyaiLink-in-a-box - Setup ........................................................................................ 3
Step 1 – Connect the tracer with the HoyaiLink-in-a-box.................................................... 3
Step 2 – Tracer Setup ........................................................................................................ 3
Step 3 – Finding the IP....................................................................................................... 4
Step 4 – Configuration on the iPad:.................................................................................... 6
Step 5 – Possible solutions in case the connection does not work: .................................... 7
Hoya Vision Care Europe
Page 1
Introduction
HoyaiLink-in-a-box is been created to offer a possibility to trace a frame from any mobile
device or in a terminal server environment. In case you want to summit an order completely
mobil you can order the lens with the HoyaiLog app and even trace from the iPad.
iPad
Requirements
•
Tracer (like the GT-5000)
•
Serial cable
•
HoyaiLink-in-a-box
•
Power cable
•
LAN cable
•
VGA cable
•
Keyboard, mouse and a monitor
•
Terminal Server environment (like an iPad)
Hoya Vision Care Europe
Page 2
Part I – HoyaiLink-in-a-box - Setup
Step 1 – Connect the tracer with the HoyaiLink-in-a-box
In order to setup HoyaiLinkHoyaiLink-inin-a-box please proceed as follows:
•
Connect the HoyaiLinkHoyaiLink-inin-a-box with the power cable and turn on the power switch on
the back side of the box
•
Connect the LAN cable with the HoyaiLinkHoyaiLink-inin-a-box
•
Connect the Tracer with the HoyaiLinkHoyaiLink-inin-a-box by using the serial cable
•
Connect the monitor with the HoyaiLinkHoyaiLink-inin-a-box with the VGA cable
•
Connect the keyboard and the mouse using the USB ports on the box
Step 2 – Tracer Setup
HoyaiLink-in-a-box supports all Tracers which are implemented in HoyaiLog.
HoyaiLog
Recommendation: GTGT-5000 which needs to have following configurations:
•
Serial
•
Hoya3 format
Hoya Vision Care Europe
Page 3
Step 3 – Finding the IP
After you have done part I please double-check that the box is on.
On the monitor you will se the following screen:
Please enter following details:
User:
hoya
Password:
root
Now go to the LX Terminal: press the bottom left button (in windows it would be the windows
button) go to Accessories and then to LX Terminal.
Terminal. Now type following command in order to
find an IP
#ifconfig
Hoya Vision Care Europe
Page 4
Now you see following:
# ifconfig
eth0
Link encap:Ethernet HWaddr 00:1b:eb:63:8c:19
inet addr:10.8.51.26 Bcast:10.8.51.255
Mask:255.255.254.0
inet6 addr: fe80::21b:ebff:fe63:8c19/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:43697 errors:0 dropped:0 overruns:0 frame:0
TX packets:13556 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:20026127 (20.0 MB) TX bytes:1253157 (1.2 MB)
Interrupt:10
lo
Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:328 (328.0 B) TX bytes:328 (328.0 B)
If you have DHCP, the box will have an IP automatically assigned to eth0 (as highlighted
above)..
In case you do not have DHCP, you need to set the IP manually
Hoya Vision Care Europe
Page 5
Step 4 – Configuration on the iPad:
Open HoyaiLog on your iPad or on the Terminal Server environment.
Press the H on the top left corner and go to Settings -> Workstation -> Advanced Settings
Please tick the checkcheck-box in order to use the Network-Tracer and enter the IP address in the
highlighted field which you saw behind eth0 (see page 5).
Further these settings have to be configured under Workstation -> Tracer as show in the
picture
Note: Please select COM0 for the COM port (as seen in the picture).
Hoya Vision Care Europe
Page 6
It will automatically apply your choice to the HoyaiLink referred by the IP address.
Save your configurations
After everything is done you can remove the monitor including the keyboard and the mouse
from the HoyaiLink-in-a-box.
It is only needed in order to see the IP address which had to be entered in Hoyailog.
Start to trace , enjoy !
Hoya Vision Care Europe
Page 7
Step 5 – Possible solutions in case the connection does not work:
You might not see an IP which is assigned to eth0.
eth0.
Therefore please remove the following file by using the LX Terminal.
Terminal.
Please use following commands in order to delete the file:
# cd /etc/udev/rules.d/70-persistent-net.rules
# sudo rm /etc/udev/rules.d/70-persistent-net.rules
Then reboot the “HoyaiLink-in-a-box” and you will have eth0 active again.
Now repeat the steps 1 till 4.
Hoya Vision Care Europe
Page 8
Download PDF