High Performance Security Display Devices - Tri-Ed

LCD15HDMI/LCD17HDMI/LCD19HDMI
SECURITY RATED 15”, 17” & 19” LCD MONITORS w/ 2xBNC, HDMI AUDIO & 3D COMB FILTER
High Performance
Security Display Devices
3625 Cincinnati Avenue, Rocklin, CA 95765 ♦ 855-388-7422 ♦ www.northernvideo.com
Rev. 081214
LCD15HDMI / LCD17HDMI / LCD19HDMI
1 INTRODUCTION AND PACKAGE CONTENTS
Congratulations on your purchase. You can expect only the sharpest and most
brilliant color images from this monitor. Featuring OSD controls and built in
speakers, you will find this monitor both easy to use and a pleasure to look at.
Package Contents
(1) LCD Monitor
(1) 12 Volts DC Power Adapter/Power Cord
(1) D-Sub 15-pin VGA Connector Cable
(1) HDMI Cable
(1) User’s Guide
2 REGULATIONS
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generation, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
■■ Reorient or relocate the receiving antenna.
■■ Increase the separation between the equipment and receiver.
■■ Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
■■ Consult the dealer or an experienced radio/TV technician for help.
LCD15HDMI / LCD17HDMI / LCD19HDMI
3 PRECAUTIONS AND MAINTENANCE
Read all of these instructions and save them for later use.
Follow all warnings and instructions on the product.
Product
II Do not cover or block the vent holes in the case.
II Do not insert sharp objects or spill liquid into the LCD monitor through
cabinet slots. They may cause an accidental fire, electric shock or failure.
II Disconnect the power plug from the AC outlet if you will not use it for an
indefinite period of time.
II Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage potentials or other risks.
II Do not touch the screen directly with your fingers. You may damage the
screen, and oil from your skin is difficult to remove.
II Do not apply pressure to the screen. The LCD is very delicate.
Power
-- Use only the type of power indicated on the marking label.
Plugs
Do not remove any of the prongs of the monitor’s three-pronged power plug.
Disconnect the power plug from the AC outlet under following conditions:
-- If you will not use it for an indefinite period time.
-- When the power cord or plug is damaged or frayed.
-- If the product does not operate normally when the operation instructions
are followed. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore
the product to normal operation.
-- If the product has been dropped or the cabinet has been damaged.
-- If the product exhibits a distinct change in performance, indicate a need
for service.
LCD15HDMI / LCD17HDMI / LCD19HDMI
Power and Extension Cords
-- Do not allow anything to rest on the power cord.
-- Do not locate this product where a person could walk on or trip over the
cords.
-- Use the proper power cord with correct attachment plug type. If the power
source is 120 V AC, use a power cord that has UL and C-UL approvals. If
the power source is a 240 V AC supply, use the tandem (T blade) type
attachment plug with ground conductor power cord that meets the
respective European country’s safety regulations, such as VDE for Germany.
-- Do not overload wall outlets or power cords. Ensure that the total of all
units plugged into the wall outlet does not exceed 10 amperes.
-- Ensure that the total ampere rating of all units plugged into the extension
cord is not over the cord’s rating.
-- If the power supply cord, which came with your monitor, is to be
connected to the PC instead of the wall outlet, this equipment is to be
used with UL/TUV approved computers with receptacle rated 100~240V
AC, 50/60Hz, 2.0A(minimum).
Environment
II
II
II
II
Place the monitor on a flat and leveled surface.
Place the monitor in a well-ventilated place.
Keep the monitor away from
Extremely hot, cold or humid places, places directly under sunlight, dusty
surroundings, equipment that generate strong magnetic fields.
4 HARDWARE INSTALLATION
The following sections in this guide give clear, step-by-step descriptions of the
installation process and explain how to use the monitor for optimum results.
Please pay attention to the Regulations and Warnings Section of this user’s
manual before setting up the display monitor. Failure to do so may inadvertently
result in personal injuries or machine damage.
LCD15HDMI / LCD17HDMI / LCD19HDMI
Step 1 Video Cable Connections
Your LCD monitor can accept BNC, VGA and HDMI video input cables.
When Using a BNC Cable: Attach the BNC cable to the AV1 or AV2 input. Secure
the BNC cable by twisting the connector to lock the cable into position.
When Using A VGA Cable: Attach the VGA cable making sure not to damage any
of the pins on the cable. Once the cable is properly seated, twist both side screws
to secure the VGA cable in place. Note that the shape of the VGA cable will only
allow it to be inserted into the VGA input in one way.
When Using A HDMI Cable: Attach the HDMI cable by gently pushing the cable
into the HDMI input making sure it is properly seated. Note that the shape of the
HDMI cable will only allow it be inserted into the HDMI input in one way.
Step 2 Audio Cable Connections
Your LCD monitor can accept both RCA and PC audio input cables.
When using RCA cables: Attach the male ends of both RCA cables into the AV
audio inputs. Match the color of the cable to the color of the RCA cable input.
When using PC cables: Attach the male end of the PC cable into the PC audio
input.
Step 3 Power Cable Connections
Connect the 3-prong power cord to a wall outlet or surge protected power strip.
It is recommended to always use a surge protection device for providing power to
the LCD.
Insert the power cord into the power adapter provided with your LCD.
Insert the 2.1-5.5mm power connector into the DC power input.
AV2
OUTPUT
(BNC)
AV2
INPUT
(BNC)
AV1
AV1
AV
OUTPUT INPUT AUDIO
(BNC) (BNC) (RCAx2)
PC
AUDIO
(mini)
VGA
HDMI
DC
LCD15HDMI / LCD17HDMI / LCD19HDMI
5 MONITOR AND OSD CONTROL
The LCD color monitor has a simple control layout for controlling the monitor and
OSD (On Screen Display) functions. The table below summarizes the control keys
and their related functions.
KEYS
FUNCTION DESCRIPTION
POWER
PRESSING THIS KEY TURNS THE DISPLAY SYSTEM POWER ON/OFF.
MENU
ENTER THE MAIN MENU OF THE ON-SCREEN DISPLAY (OSD).
AUTO
AUTOMATICALLY ADJUSTS H-POSITION, V-POSITION,
PIXEL CLOCK AND PHASE FOR AN OPTIMAL IMAGE. (PC MODE ONLY)
SELEC T
SWITCH MODE “PC”,”AV1”,”AV2”,”HDMI”.
ADJUST
INCREASE OR DECREASE THE VALUE OF THE CHOSEN ITEM.
MENU
SELECT ADJUST
Menu
Select
AUTO
POWER
Auto
LED INDICATOR
LED Status Display
The following table describes the various power states of the LCD monitor which
are represented by different LED colors.
POWER STATE
LED COLOR
ON
GREEN
STANDBY
RED
NO POWER
BLANK
LCD15HDMI / LCD17HDMI / LCD19HDMI
6 OSD CONTROL FUNCTION LIST
Picture Mode
1. PIC TURE MODE
2. CONTRAST
3. BRIGHTNESS
5. TINT
6. SHARPNESS
7. COLOR TEMP.
8. DNR
PRESS “◄” OR “►” TO SELEC T THE PIC TURE MODE
“USER, STANDARD, MOVIE, VIVID”
THIS IS USED TO ADJUST THE IMAGE CONTRAST.
PRESS “◄” OR “►” TO ADJUST THE PARAMETER.
THIS IS USED TO SET THE BRIGHTNESS OF THE SCREEN.
PRESS “◄” OR “►” TO ADJUST THE PARAMETER.
ADJUST THE SCREEN DEFLEC TION OF RED OR GREEN.
PRESS “◄” OR “►” TO ADJUST THE PARAMETER.
ADJUST THE SOFTNESS OR SHARPNESS OF THE IMAGE.
PRESS “◄” OR “►” TO ADJUST THE PARAMETER.
PRESS “◄” OR “►” TO ADJUST THE COLOR TONES.
“ COOL , WARM , NORMAL “
PRESS “◄” OR “►” TO ADJUST THE NOISE REDUC TION.
“HIGH , MEDIUM , LOW , OFF “
NOTE: NO. 2,3 & 7 ONLY IN PC MODE.
LCD15HDMI / LCD17HDMI / LCD19HDMI
Sound Mode
1. VOLUME
PRESS “◄” OR “►” TO INCREASE OR DECREASE VOLUME LEVEL.
2. MUTE
PRESS “◄” OR “►” TO SELEC T “SOUND OR MUTE” MODE.
Video Setting Mode
1. MULTI WINDOW
PRESS “◄” OR “►” TO SELEC T “PIP, POP, OFF ” MODE.
2. SUB SOURCE
PRESS “◄” OR “►” TO SELEC T “AV, VGA” MODE.
3. SIZE
ADJUST THE SIZE OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “LARGE, SMALL”.
4. POSITION
5. BORDER COLOR
6. SOUND SOURCE
7. SWAP
MOVE THE POSITION OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “L U, R D, R U, L R” POSITION.
CHOOSE THE BORDER COLOR OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “BLACK, BLUE” COLOR.
PRESS “◄” OR “►” TO SELEC T “MAIN, SUB” MODE.
PRESS S/SELEC T TO SWAP THE SOURCE OF MAIN AND SUB.
5. BORDER COLOR
CHOOSE THE BORDER COLOR OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “BLACK, BLUE” COLOR.
6. SOUND SOURCE
PRESS “◄” OR “►” TO SELEC T “MAIN, SUB” MODE.
LCD15HDMI / LCD17HDMI / LCD19HDMI
PIP/POP SETUP MODE
1. MULTI WINDOW
PRESS “◄” OR “►” TO SELEC T “PIP, POP, OFF ” MODE.
2. SUB SOURCE
PRESS “◄” OR “►” TO SELEC T “AV, VGA” MODE.
3. SIZE
ADJUST THE SIZE OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “LARGE, SMALL”.
4. POSITION
MOVE THE POSITION OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “L U, R D, R U, L R” POSITION.
5. BORDER COLOR
CHOOSE THE BORDER COLOR OF SUB SOURCE WINDOW.
PRESS “◄” OR “►” TO SELEC T “BLACK, BLUE” COLOR.
6. SOUND SOURCE
PRESS “◄” OR “►” TO SELEC T “MAIN, SUB” MODE.
7. SWAP
PRESS S/SELEC T TO SWAP THE SOURCE OF MAIN AND SUB.
LCD15HDMI / LCD17HDMI / LCD19HDMI
7 CARING FOR YOUR LCD MONITOR
The LCD color monitor is a sensitive piece of electronic equipment. Proper
care can prevent accidentally damaging the LCD panel or the monitor itself. By
following these guidelines you can ensure many years of trouble free use.
1. The LCD monitor’s plastic casing and LCD panel can be cleaned with a soft,
lint-free cloth. Never use scrub pads or other cleaning materials with abrasive
surfaces to clean your LCD monitor!
a. A slightly damp cloth may be used to clean fingerprints or smudges from
the LCD screen.
b. For the plastic case, a mild detergent may be used to clean the surface.
However, you should ensure not to use too much detergent or water as
this could leak into the interior of the casing.
2. Avoid direct contact with water or other liquids. Never use the LCD monitor
in or around areas where water may pose a potential hazard to normal
operation.
3. Only use the LCD monitor indoors, and avoid monitor contact with oil, vapor,
steam, moisture and dust. The LCD monitor should be used in a clean and low
humidity environment.
4. Keep the LCD monitor away from heaters or other heat sources such as
lighting equipment or direct sunlight.
5. Do not touch the LCD monitor screen with sharp objects like fingernails or
pencils.
WARNING: Any unauthorized modification to this equipment will void the
product warranty.
LCD15HDMI / LCD17HDMI / LCD19HDMI
8 FREQUENTLY ASKED QUESTIONS
Power Button Does Not Respond
Check the power cord to ensure that it is securely plugged into the monitor base
and also into the electrical outlet.
Ensure there is electrical power coming from the AC outlet. (Use another device to
check for power.)
Unplug the power cord of the monitor from the AC outlet; wait a few minutes,
then to plug the power cord into the AC outlet again. This will reset the monitor
and power supply.
No Image On The Screen
Ensure that the DB-15 signal cable is properly connected to the display card/
computer. Check the DB-15 signal cable connector on both ends for bent or
pushed-in pins.
The display card should be properly seated in its card slot.
Ensure that the computer’s power switch is ON.
Ensure that the monitor’s power switch is ON.
Unplug the power cord of the monitor from the AC outlet; wait a few minutes,
then to plug the power cord into the AC outlet again. This will reset the monitor
and power supply.
Power LED is RED (With No Image On The Screen)
Check the DB-15 signal cable to ensure that it is properly attached to the graphics
display card.
Check the DB-15 signal cable on both ends for bent or pushed-in pins.
Make sure the computer is not in a power-saving mode (move the mouse or press
a key on the keyboard).
No Sound Coming From The Audio Speakers
The audio cable should be connected to the lineout on the audio card and the
line-in on the monitor. Ensure that the audio cable is properly connected.
Inspect the audio cable for any apparent damage. Double check by switching to
another audio cable to see if the audio works.
LCD15HDMI / LCD17HDMI / LCD19HDMI
9 MOUNTING THE LCD MONITOR
Your monitor comes pre-assembled with a desk-top mount but can also be wall
or ceiling mounted using the VESA standard mounting holes on the back of the
monitor. 17” and 19” models are compatible with VESA 100 mounting brackets.
3.94” (100mm)
3.94” (100mm)
10 FREQUENCY CHART AND SPECIFICATIONS
Frequency Chart
ITEM
RESOLUTION
H FREQ.(KHZ)
V FREQ.(HZ)
NOTE
1
640x400@70
31.460
70.080
VGA
2
640x480@60
31.469
59.940
VGA
3
640x480@72
37.861
72.809
VGA
4
640x480@75
37.500
75.000
VGA
5
720x400@70
31.460
70.080
SVGA
6
800x600@60
37.879
60.317
SVGA
7
800x600@72
48.077
72.188
SVGA
8
800x600@75
46.875
75.000
SVGA
9
1024x768@60
48.363
60.004
XGA
10
1024x768@70
56.476
70.069
XGA
11
1024x768@75
60.023
75.029
XGA
12
1280x1024@60
63.981
60.020
SXGA
13
1280x1024@75
79.976
75.025
SXGA
Note: These preset timings are recommended. Users will have to adjust
the timing manually, if they are not in this preset list.
LCD15HDMI / LCD17HDMI / LCD19HDMI
11SPECIFICATIONS
Specifications
SPECIFICATIONS
Native Resolution
Active Display Area
LCD15HDMI
LCD17HDMI
1024 x 768 @ XGA
LCD19HDMI
1280 x 1024 SXGA
11.96" x 8.97"
13.38" x 10.7"
Supported Resolution
14.88" x 11.96"
640 x 480 VGA
800 x 600 SVGA
1024 x 768 XGA
N/A
1280 x 1024 SXGA
Impedance
75 Ohms
Video Input Signal
1V (p-p)
Aspect Ratio
Pixel Pitch
4:3
0.297 x 0.297 (mm)
0.264 x 0.264 (mm)
Color Depth
Brightness
Contrast Ratio
260 cd/m2
300 cd/m2
700:1
800:1
Viewing Angle (H/V)
Response Time
160° / 160°
8ms
5ms
Lamp Life Time (Min.)
> 25,000 Hours
Auto Adjustment
Yes
Certificates
Energy Star, UL/CUL, FCC-DOC, CE, ROHS
Input Voltage
AC 100 ~ 240V
Power Supply
12 Volts DC
Power Consumption
BNC
0.294 x 0.294 (mm)
16.7M
35 Watts
Picture Mode - Contrast, Brightness, Color, Tint, Sharpness, Color , DNR
Sound Mode - Volume
Setup Mode - Language, Source,
Video Settings - H.Position, V.Position,
VGA / HDMI
Picture Mode - Contrast, Brightness, Color
Sound Mode - Volume
Setup Mode - Language, Source,
Video Settings - H.Position, V.Position,
Video
BNC In/Out (x2)
VGA (x1) / HDMI (x1)
Audio
RCA (x2 - Stereo)
PC Audio In (x1)
Dimensions (Monitor only)
12.25" x 14.4" x 1.9" (H x W x D)
14.6" x 16.5" x 2.4" (H x W x D)
14.6" x 16.9" x 2.5" (H x W x D)
Weight
6.6lb
12.8lb
13.2lb
Package Weight
8.6lb
13.3lb
14.4lb
17.0" x 19.5" x 5.0”
19.6" x 22.0" x 6.12”
19.6” x 22.0” x 6.12”
Package Dimensions
Operating Temp
23° ~ 104°F
Storage Temp
-13° ~ 140°F
* All specifications subject to change without notice for quality improvement.
LCD15HDMI / LCD17HDMI / LCD19HDMI
1 ACCESSORIES
Included Accessories:
(1) 12 Volts DC Power Adapter/Power Cord
(1) D-Sub 15-pin VGA Connector Cable
(1) HDMI Cable
(1) User’s Guide
Recommended Accessories:
MONWM1
MONWM2
MONWM3
Pivoting LCD
Monitor Mount
Fully Adjustable
LCD Monitor Mount
Dual Arm Fully Adjustable
LCD Monitor Mount
CBL3BNC
CBL6BNC
3’ BNC Cable
Also Available in
6’, 25’, 50’ and 100’
6’ BNC Cable
Also Available in
3’, 25’, 50’ and 100’
LCD15HDMI / LCD17HDMI / LCD19HDMI
NOTES
Download PDF