ASM-LS - AEM Corp

ASM-LS
LSxxx Series
High Power Loud Speaker
INSTALLATION AND OPERATION MANUAL
REV 1.00 April 24, 2015
Anodyne Electronics Manufacturing Corp.
15-1925 Kirschner Road
Kelowna BC, Canada
V1Y 4N7
Telephone (250) 763-1088
Facsimile (250) 763-1089
Website: www.aem-corp.com
© 2015 Anodyne Electronics Manufacturing Corp. (AEM),
All Rights Reserved
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
COPYRIGHT STATEMENT
© 2015 Anodyne Electronics Manufacturing Corp. (AEM), All Rights
Reserved
This publication is the property of AEM and is protected by Canadian
copyright laws. No part of this document may be reproduced or transmitted
in any form or by any means including electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission
of AEM.
Installation and Operation Manual
Page ii
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
Prepared By:
Checked By:
Rick Gostlin
Designer
Apr 29, 2015
Tony Pearson
Designer
Apr 29, 2015
Approved By:
Tom Betzelt
Product Support
Manager
April 29th, 2015
Todd Blackstock
R&D Manager
Apr 29/15
The status of this installation and operation manual is controlled by the revision shown on the title page.
The status of each section is controlled by revision shown in the footer of each page. All revisions
affecting sections of this manual have been incorporated.
AEM MANUAL REVISIONS
Section
Revision Number
Revision Description
Date
All
Rev 1.00
Initial Release
April 24, 2015
Installation and Operation Manual
Page iii
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
Table of Contents
Section
Title
1.0
Description
1.1
1.2
1.3
1.4
1.4.1
1.4.2
1.4.3
1.5
Introduction
Product Description
Design Features
Specifications
Electrical Specifications
Physical Specifications
Environmental Specifications
System Configuration
2.0
Installation
2.1
2.2
2.2.1
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.4
2.5
2.6
2.7
Introduction
Unpacking and Inspection
Warranty
Installation Procedures
Warnings
Cautions
Cabling and Wiring
Mechanical Installation
Post-Installation Checks
Accessories Required But Not Supplied
Continued Airworthiness
Speaker Location and Orientation
Installation Drawings
3.0
Operation
3.1
Operation Specifics
Installation and Operation Manual
Page
1-1
1-1
1-2
1-2
1-2
1-2
1-2
1-3
2-1
2-1
2-1
2-1
2-1
2-2
2-2
2-3
2-3
2-3
2-3
2-4
2-6
3-1
Page iv
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
Section 1.0 Description
1.1
Introduction
Information in this section consists of product description, design features and specifications for the
LSxxx Series High Power Loud Speakers.
Review all notes, warnings and cautions.
1.2
Product Description
The LSxxx Series Loud Speakers are high output power loud speakers for use in air-to-ground, air-to-sea, or
ground-to-ground audible communication systems. The LSxxx Series speakers are intended for use with the
LSA400 or LSA800 series amplifiers and a siren controller as a complete system.
Siren Controller
April 24, 2015 Rev: 1.00
Loud Speaker Amplifier
Loud Speakers
Page 1-1
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
1.3
Design Features
This series of speakers is available in a single, double, or triple bell configuration, which allows the user to
vary the range and/or dispersal pattern depending on the mounting configurations.
The speaker drivers have been updated to provide much better conversion of electrical power (Watts) to
sound pressure (SPL).
The driver assembly and newly designed mechanical parts are field replaceable for ease of maintenance.
The LSxxx Series speakers are designed and qualified to meet many operational roles of current and
future light, medium, and heavy helicopters as well as fixed wing aircraft.
1.4
Specifications
1.4.1
Electrical Specifications
Loudspeaker
Total Bell
Configuration
Impedance
LS300-200
1
5.5 ȍ
LS600-200
2
2 Channels at
5.5 ȍ each
Rated Peak
Power
Output Level
@ 1m & Rated
Peak Power
300 Watts
Peak
600 Watts
Peak
130dB
135dB
Weight
15 lbs
[6 kg]
28 lbs
[12.7 kg]
At the time of publication, performance information was available only for the speakers listed above. For
details of other units, please contact the Product Support department at AEM.
1.4.2
Physical Specifications
See Mechanical Installation drawings (LSxxx-xxx-922-0) for speaker physical specifications
(where x is the model reference of the specific unit under consideration, i.e. LS300-200-922-0)
1.4.3
Environmental Specifications
Temperature
-40 to +60qC (operating)
-55 to +85qC (survival)
Altitude
+25,000 ft. (+7,620 m) max.
Humidity
95% Non-condensing
Shock
6g (any axis)
Vibration
DO-160G Category ‘S’ Curves B & M
and Category ‘U2’ Curves F & F1
Magnetic Effect
DO-160G category ‘B’
April 24, 2015 Rev: 1.00
Page 1-2
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
1.5
System Configuration
Loud Speaker
LS300-200
LS600-200
LS600-200
1 X LS300-200
1 X LS600-200
2 X LS300-200
2 X LS600-200
Total Bell
Configuration
1
2
2
Amplifier
Input Power
LSA400
LSA400
LSA800
28 Vdc
28 Vdc
28 Vdc
Output Level
@ 1m
130dB
135dB
135dB
3
LSA800
28 Vdc
137dB
2
4
LSA800
LSA800
28 Vdc
28 Vdc
135dB
141dB
At the time of publication, performance information was available only for the speakers listed above. For
details of other units, please contact the Product Support department at AEM.
End of Section 1.0
April 24, 2015 Rev: 1.00
Page 1-3
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
Section 2.0 Installation
2.1
Introduction
Information in this section consists of: unpacking and inspection procedures, installation procedures,
post-installation checks, and installation drawings.
2.2
Unpacking and Inspection
Unpack the equipment carefully. Inspect the unit visually for damage due to shipping and report all such
claims immediately to the carrier involved. Note that each unit should have the following:
- LSxxx Series High Power Loud Speaker
- Product Information Card
- Certificate of Conformity or Release Certification
Verify that all items are present before proceeding and report any shortage immediately to your supplier.
2.2.1
Warranty
All Anodyne Electronics Manufacturing Corp. (AEM) products are warranted for 2 years. See the website
www.aem-corp.com/warranty for complete details.
2.3
Installation Procedures
2.3.1
Warnings
WARNING:
When the speaker is connected to an appropriate amplifier, the system
is capable of producing high sound pressure levels. Proper personal
protective equipment is required to prevent hearing damage.
Stand clear, this equipment operates at an intense sound level.
Personnel must be kept away from the direct loud speaker beam.
April 24, 2015 Rev: 1.00
Page 2-1
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
2.3.2
Cautions
CAUTION:
Do not operate the equipment in a hangar or in confined areas.
Do not operate the equipment with snow, water or other foreign matter in the
loud speaker horn.
Do not clean the loud speaker with compressed air.
Bundle and route the Speaker Output wires separately from low level Audio
Input lines.
Always check ADF and compass calibration after installing external speakers
or power amplifiers.
2.3.3
Cabling and Wiring
All wire shall be selected in accordance with the original aircraft manufacturer's Maintenance Instructions
or AC43.13-1B Change 1, Paragraphs 11-76 through 11-78. Unshielded wire types shall qualify to MILW-22759 as specified in AC43.13-1B Change 1, Paragraphs 11-85, 11-86, and listed in Table 11-11. For
shielded wire applications, use Tefzel MIL-C-27500 shielded wire with solder sleeves (for shield
terminations) to make the most compact and easily terminated interconnect. Follow the interconnect
drawing in Section 2.7 as required.
Allow 3" from the end of the shielded wiring to the shield termination to allow the connector hood to be
easily installed. Refer to the interconnect drawing in Section 2.7 for shield termination details. Note that
the hood is a "clamshell" hood, and is installed after the wiring is complete. Aircraft harnessing shall
permit the unit to be removed for easy access to all adjustments.
Maintain wire segregation and route wiring in accordance with the original aircraft manufacturers
Maintenance Instructions.
April 24, 2015 Rev: 1.00
Page 2-2
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
2.3.4
Mechanical Installation
The installing agency is responsible for the design, engineering and installation of the mounting bracket
for the LSxxx Series High Power Loud Speakers. Careful consideration should be given to the operating
environment and the mechanical forces acting upon the LSxxx Series unit(s). The LSxxx-200 series of
loud speakers, Rev 2.00 or later, can be mounted using the AFM-SB-XX series of Meeker Aviation mount
brackets.
AEM Part Number
LS300-200
LS600-200
Required Meeker Aviation
Mounting Bracket
AFM-SB-1D
AFM-SB-1B
For information and availability of the AFM-SB-XX series of mounting brackets contact Meeker Aviation:
Meeker Aviation
#206 19142 122nd Ave
Pitt Meadows, BC
Canada V3Y 2P9
PH: 604-644-1125
FAX: 760-758-9612
www.meekeraviation.com
2.3.5
Post-Installation Checks
Ensure all connectors are tight and the speaker array mechanical installation is sound.
Ensure that the speakers are secure and adjusted with the line of sight focused towards the intended
target. See section 2.6 for speaker location and orientation information.
When the PA system installation is complete, carry out a full performance test to ensure that all
components of the system (including the loud speaker array) are functioning correctly.
2.4
Accessories Required But Not Supplied
LS300-IK
LS300 and LS600 90° Sealed Screw Terminal Installation Kit
2.5
Continued Airworthiness
Maintenance of the LSxxx Series is ‘on condition’ only. Periodic maintenance of this product is not
required.
April 24, 2015 Rev: 1.00
Page 2-3
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
2.6
Speaker Location and Orientation
April 24, 2015 Rev: 1.00
Page 2-4
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
April 24, 2015 Rev: 1.00
Page 2-5
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
2.7
Installation Drawings
DRAWING
LSxxx-403-0
LS300-405-0
LS300-405-0
LS600-405-0
LS600-405-0
LS300-200-922-0
LS300-200-922-0
LS600-200-922-0
LS600-200-922-0
REV.
1.00
2.00
1.00
2.00
1.00
2.00
1.10
2.00
1.00
DESCRIPTION
Loud Speaker Configurations
Loud Speaker, LS300
Loud Speaker, LS300
Loud Speaker, LS600
Loud Speaker, LS600
Loud Speaker, LS300
Loud Speaker, LS300
Loud Speaker, LS600
Loud Speaker, LS600
TYPE
Interconnect
Connector Map
Connector Map
Connector Map
Connector Map
Mechanical Installation
Mechanical Installation
Mechanical Installation
Mechanical Installation
SERIAL NO.
All
1006 and up
Up to 1005
1006 and up
Up to 1005
1006 and up
Up to 1005
1006 and up
Up to 1005
Section 2.0 ends following the above documents
April 24, 2015 Rev: 1.00
Page 2-6
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
NAME
DATE
UNLESS OTHERWISE SPECIFIED:
Apr 24/15
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
FRACTIONAL_____________ ±0.0625"
ANGULAR_______________ ±0.5°
TWO DECIMAL PLACE____ ±0.010"
THREE DECIMAL PLACE___ ±0.005"
LAC
Apr 28/15
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
TITLE:
MATERIAL:
FINISH:
LOUD SPEAKER CONFIGURATIONS
INTERCONNECT
REVISION
PAPER SIZE: CAGE CODE PART No.:
A
SCALE:1:1
L9015
DO NOT SCALE DRAWING
LSxxx
DRAWING No.: 403-0
1.00
SHEET: 1 of 2
NAME
DATE
UNLESS OTHERWISE SPECIFIED:
Apr 24/15
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
FRACTIONAL_____________ ±0.0625"
ANGULAR_______________ ±0.5°
TWO DECIMAL PLACE____ ±0.010"
THREE DECIMAL PLACE___ ±0.005"
LAC
Apr 28/15
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
TITLE:
MATERIAL:
FINISH:
LOUD SPEAKER CONFIGURATIONS
INTERCONNECT
REVISION
PAPER SIZE: CAGE CODE PART No.:
A
SCALE:1:1
L9015
DO NOT SCALE DRAWING
LSxxx
DRAWING No.: 403-0
1.00
SHEET: 2 of 2
16-Feb-14
Apr 28/15
NAME
DATE
UNLESS OTHERWISE SPECIFIED:
12-Nov-14
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
FRACTIONAL_____________ ±0.0625"
ANGULAR_______________ ±0.5°
TWO DECIMAL PLACE____ ±0.010"
THREE DECIMAL PLACE___ ±0.005"
DMF
Nov 14/14
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
TITLE:
LOUD SPEAKER
CONNECTOR MAP
MATERIAL:
FINISH:
REVISION
PAPER SIZE: CAGE CODE PART No.:
A
L9015
SCALE:NTS
LS300
DO NOT SCALE DRAWING DRAWING No.: 405-0
1.00
SHEET:1 of 1
16-Feb-14
Apr 9/15
DRAWN
NAME
DATE
UNLESS OTHERWISE SPECIFIED:
DMF
13-Nov-14
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
FRACTIONAL_____________ ±0.0625"
ANGULAR_______________ ±0.5°
TWO DECIMAL PLACE____ ±0.010"
THREE DECIMAL PLACE___ ±0.005"
CHECKED
13-Nov-14
APPROVED
16-Dec-14
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
ANODYNE
ELECTRONICS
MANUFACTURING CORP.
TITLE:
LOUD SPEAKER
CONNECTOR MAP
MATERIAL:
NA
FINISH:
NA
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
REVISION
PAPER SIZE: CAGE CODE PART No.:
A
L9015
LS600
SCALE:NTS DO NOT SCALE DRAWING DRAWING No.: 405-0
1.00
SHEET:1 of 1
REVISIONS
REV.
2.00
DESCRIPTION
ECO# 1037, NEW DESIGN AFTER VIBRATION TESTING
DATE
NAME
02-Mar-15
DMF
NOTES:
1. MASS 15 lbs [6.8 kg] MAX.
2.
DENOTES CENTER OF GRAVITY (est.)
167.9
6.61
147.1
5.79
126 MAX
5.0 MAX
325 MAX
12.8 MAX
2.000 BOLT PATTERN
198 MAX
7.8 MAX
1/4"-28 THREADED
3/4" MAX DEPTH OF SCREW
DETAIL A
MOUNTING HOLE PATTERN
SCALE 2 : 5
82.6
3.25
32.6
1.28
86
3.4
37.8
1.49
168 MAX
6.6 MAX
A
260 MAX
10.3 MAX
126
4.96
168 MAX
6.6 MAX
DRAWN
NAME
DATE
DMF
14-Nov-14
CHECKED
11-Mar-15
APPROVED
Apr 28/15
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS DRAWING
IS THE SOLE PROPERTY OF ANODYNE
ELECTRONICS MANUFACTURING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF ANODYNE
ELECTRONICS MANUFACTURING IS PROHIBITED.
15-1925 KIRSCHNER RD.
KELOWNA BC V1Y 4N7
(250)-763-1088
WWW.AEM-CORP.COM
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
ANGULAR_________________ 0.5
FRACTIONAL______________ 0.0625"
ONE DECIMAL PLACE_______ 0.100"
TWO DECIMAL PLACE______ 0.030"
THREE DECIMAL PLACE_____ 0.010"
TITLE:
MATERIAL:
N/A
LOUD SPEAKER
MECHANICAL INSTALLATION
REVISION
PAPER SIZE: CAGE CODE PART No. :
FINISH:
N/A
A
SCALE: 1:5
L9015
DO NOT SCALE DRAWING
LS300-200
DRAWING No. : 922-0
2.00
SHEET: 1 OF 1
REVISIONS
REV.
1.10
DESCRIPTION
RAS# 379, ADDED 3/8-16 THREADED NOTE, UPDATED DIMENSION SIZES
DATE
NAME
17-Nov-14
DMF
NOTES:
1. MASS 15 lbs [6 kg] MAX.
2.
DENOTES CENTER OF GRAVITY (est.)
5.89
147.3 MAX
5.8 MAX
2.250
345.4 MAX
13.6 MAX
197 MAX
7.8 MAX
2.250
1/4-20 THREADED MAX
3/4" PROTRUSION OF
BOLT INTO LOUD
SPEAKER CHASSIS
SCALE 1 : 3
DIAMOND MOUNTING PATTERN
84.8
3.3
100.1
3.9
1.10
271.8 MAX
10.7 MAX
172.7 MAX
6.8 MAX
132.9
5.2
1.10
3/8-16 THREADED
1.10
DRAWN
172.7 MAX
6.8 MAX
NAME
DATE
DMF
14-Nov-14
CHECKED
14-Nov-14
APPROVED
Nov 17/14
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS DRAWING
IS THE SOLE PROPERTY OF ANODYNE
ELECTRONICS MANUFACTURING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF ANODYNE
ELECTRONICS MANUFACTURING IS PROHIBITED.
1.10
15-1925 KIRSCHNER RD.
KELOWNA BC V1Y 4N7
(250)-763-1088
WWW.AEM-CORP.COM
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
ANGULAR_________________ 0.5
FRACTIONAL______________ 0.0625"
ONE DECIMAL PLACE_______ 0.100"
TWO DECIMAL PLACE______ 0.030"
THREE DECIMAL PLACE_____ 0.010"
TITLE:
MATERIAL:
N/A
LOUD SPEAKER
MECHANICAL INSTALLATION
REVISION
PAPER SIZE: CAGE CODE PART No. :
FINISH:
N/A
-
A
SCALE: 1:5
L9015
DO NOT SCALE DRAWING
LS300-200
DRAWING No. : 922-0
1.10
SHEET: 1 OF 1
8
7
6
5
6
7
8
5
REVISIONS
REV.
334
13.15
2.00
DESCRIPTION
ECO# 1037, NEW DESIGN AFTER VIBRATION TESTING
DATE
NAME
11-Mar-15
DMF
313.2
12.33
D
D
NOTES:
1. MASS 28 lbs [12.7 kg] MAX.
126 MAX
5.0 MAX
2.
DENOTES CENTER OF GRAVITY (est.)
325 MAX
12.8 MAX
198 MAX
7.8 MAX
C
C
165.5
6.51
89
3.5
2.000 BOLT PATTERN
40.5
1.59
B
B
168 MAX
6.6 MAX
A
260 MAX
10.3 MAX
1/4"-28 THREADED
3/4" MAX DEPTH OF SCREW
126
4.96
DETAIL A
MOUNTING HOLE PATTERN
SCALE 1 : 2
335 MAX
13.2 MAX
NAME
A
DRAWN
DMF
DATE
14-Oct-14
CHECKED
11-Mar-15
APPROVED
Apr 8/15
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED IN THIS DRAWING
IS THE SOLE PROPERTY OF ANODYNE
ELECTRONICS MANUFACTURING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF ANODYNE
ELECTRONICS MANUFACTURING IS PROHIBITED.
8
7
6
5
8
15-1925 KIRSCHNER RD.
KELOWNA BC V1Y 4N7
(250)-763-1088
WWW.AEM-CORP.COM
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
ANGULAR_________________ 0.5
FRACTIONAL______________ 0.0625"
ONE DECIMAL PLACE_______ 0.100"
TWO DECIMAL PLACE______ 0.030"
THREE DECIMAL PLACE_____ 0.010"
TITLE:
MATERIAL:
N/A
LOUD SPEAKER
MECHANICAL INSTALLATION
REVISION
PAPER SIZE: CAGE CODE PART No. :
FINISH:
B
N/A
SCALE: 1:4
7
L9015
2.00
LS600-200
DO NOT SCALE DRAWING
6
DRAWING No. : 922-0
SHEET: 1 OF 1
5
A
8
7
6
5
6
7
8
5
12.41
2.250
D
D
1/4-20 THREADED
MAX 3/4" PROTRUSION
OF BOLT INTO LOUD SPEAKER
2.250
342.9 MAX
13.5 MAX
198.1 MAX
7.8 MAX
DETAIL A
SCALE 1 : 2
DIAMOND MOUNTING PATTERN
C
C
13.4 MAX
158.052
6.2
4.6
B
B
A
265.7 MAX
10.5 MAX
170.2 MAX
6.7 MAX
132.858
5.2
A
DRAWN
Notes:
1. MASS 29 lbs [13.2 kg] MAX.
2.
8
DATE
DMF
14-Nov-14
CHECKED
Dec 10/14
APPROVED
16-Dec-14
CONFIDENTIAL AND PROPRIETARY
DENOTES CENTER OF GRAVITY (est.)
7
NAME
THE INFORMATION CONTAINED IN THIS DRAWING
IS THE SOLE PROPERTY OF ANODYNE
ELECTRONICS MANUFACTURING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF ANODYNE
ELECTRONICS MANUFACTURING IS PROHIBITED.
6
5
8
15-1925 KIRSCHNER RD.
KELOWNA BC V1Y 4N7
(250)-763-1088
WWW.AEM-CORP.COM
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [MM]
TOLERANCES:
ANGULAR_________________ 0.5
FRACTIONAL______________ 0.0625"
ONE DECIMAL PLACE_______ 0.100"
TWO DECIMAL PLACE______ 0.030"
THREE DECIMAL PLACE_____ 0.010"
TITLE:
MATERIAL:
N/A
LOUD SPEAKER
MECHANICAL INSTALLATION
REVISION
PAPER SIZE: CAGE CODE PART No. :
FINISH:
B
N/A
-
SCALE: 1:4
7
L9015
LS600-200
DO NOT SCALE DRAWING
6
1.00
DRAWING No. : 922-0
SHEET: 1 OF 1
5
A
LSxxx Series High Power Loud Speaker
Installation and Operation Manual
Section 3.0 Operation
3.1
Operation Specifics
The LSxxx Series High Power Loud Speaker has no normal user operational aspects.
End of Section 3.0
April 24, 2015 Rev: 1.00
Page 3-1
ENG-FORM: 806-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Download PDF