TAP-20BT 40BT TOPP PRO_V1.0

TAP SER IES
TAP20BT
TAP40BT
INDOORS MINI SPEAKER
Bluetooth
xxxxxxx-1.0
Technical Specifications
Model:
TAP20BT
Power System
Class D,20W Continuous , 40W Peak
Maximum SPL @ 1m
85dB Continuous/ 88dB Peak
Frequency Response
150Hz-20KHz (-10dB)
BT Frequency Range
2400~2500MHz
Transducer Driver
3" (78x78mm) Full Range, 0.8" (20.4mm) voice coil
Inputs
L/R RCA and 1/4" Balanced Input
External Controls
Volume Control/ Bluetooth Link with Red LED/ Bluetooth Pair with
9
Green LED / Bluetooth Pair Switch / Power Switch
Wireless connectivity
Bluetooth(A2DP)
Wireless range
30-40 feet (9-12 meters ), Typical
Power Supply
AC 220-240V or AC 110-120 Volt, 50/60Hz
Protection features
Over-excursion, thermal , short circuit protection
Enclosure Construction
Injection-molded polypropilene enclosure ; perforated steel grille.
Mounting information
PP plastic carton can revolve for 180 O with revolved fixing shelf
Dimensions (HxWxD)
115x110x175 mm (4.53" x 4.33" x 6.89")
Net Weight
1.35kg / 2.98 lbs
Model:
TAP40BT
Power System
Class D,40W Continuous ,60W Peak
Maximum SPL @ 1m
87dB Continuous/ 90dB Peak
Frequency Response
95Hz-18KHz (-10dB)
BT Frequency Range
2400~2500MHz
Transducer Driver
4" (106x106mm) Full Range, 1.0" (25.4mm) voice coil
Inputs
L/R RCA and 1/4" Balanced Input
External Controls
Volume Control/ Bluetooth Link with Red LED/ Bluetooth Pair with
Green LED / Bluetooth Pair Switch / Power Switch
Wireless connectivity
Bluetooth(A2DP)
Wireless range
30-40 feet (9-12 meters ), Typical
Power Supply
AC 220-240V or AC 110-120 Volt, 50/60Hz
Protection features
Over-excursion, thermal , short circuit protection
Enclosure Construction
Injection-molded polypropilene enclosure ; perforated steel grille.
Mounting information
PP plastic carton can revolve for 180 O with revolved fixing shelf
Dimensions (HxWxD)
136 x 140 x 206 mm(5.35" x 5.51" x 8.11")
Net Weight
2.56kg / 5.64 lbs
8
8
Block Diagram
Table of contents
1 Introduction .................................................................................................................................. 1
2 Useful Tips ..................................................................................................................................... 1
3 Useful Date ................................................................................................................................... 1
4 Control Elements ........................................................................................................................... 2
5 Installation Description ................................................................................................................. 3
6 To Set-up 2 Loudspeakers(Stereo) ................................................................................................. 5
TAP20BT/40BT BLOCK DIAGRAM
7 To Set-up 1 Loudspeaker ............................................................................................................... 6
8 Block Diagram .............................................................................................................................. 7
9 Technical Specifications ................................................................................................................ 8
Bluetooth PIN#:2013
7
1
Introduction
To Set-up 1 Loudspeaker
TAP20BT/40BT series is designed for indoor installation and most public address system. It provides
quality performance,Furthermore, we offer optional metal rotatable mounting bracket, thus you can
install TAP speaker on wall easily. This new compact speaker series meet every demands for restaurants,
supermarket, shopping mall, pubs, and so on.
The wireless loudspeakers will remember their pairing and linking settings even after they are
powered off. When you turn the loudspeakers back on, they will automatically reconnect to each
other. When the connections are re-established between the loudspeakers, the LINK LEDs will light
continuously.
1.Press and release PAIR BUTTON on the loudspeaker.You should hear a tone (beep) ; the PAIR
BLUE LED will flash.
Enjoy your TAP series speaker cabinet and make sure that read this manual carefully before operation.
2
Useful Tips
3
Useful Date
7
2.Select SEIKAKU BT2.1ONS on your Bluetooth audio device(iPhone, iPad ,Bluetooth adapter etc.).
3.Wait for device to pair. This may take a while (roughly 10 seconds or longer). When successfully
paired, the tones will stop and the PAIR BLUE LED will light solid. If the device fails to connect try
steps 2-3 again.
4.Play Music.
TO RECONNECT AFTER POWER OFF/ON:
MASTER and SLAVE loudspeakers will reconnect automatically. On your Bluetooth audio
device, pick SEIKAKU BT2.1ONS and press connect.
-Speakers should be placed in a position that allows for unobstructe sound projection. In many
instances is beneficial for speakers to be elevated on tripod stands to achieve maximum dispersion
and reach.
-Use professional advice or service when hanging and installing speakers. Please take precautions to
secure them to prevent them from falling and hurting someone. Care should be taken as to not
damage the cabinet or its components. Please comply with all pertinent Regulations.
-Using quality cables will ensure the best possible sound.
-For best results match the speakers to a good amplifier that matches the wattage & impedance of
your speakers. Proper amplification power results in good quality audio & longer component life.
Check out the power requirement for your cabinet.
-Avoid pointing a microphone directly at an amplified speaker doing because it may cause feedback
possibly damaging speaker components and your hearing.
Serial Number:
Data of Purchase:
Purchased at:
1
6
6
To Set-up 2 Loudspeakers(Stereo)
4
Control Elements
REAR PANEL OVERVIEW
RIGHT AUDIO SIGNAL
STER
TAP20BT/40BT
(MASTER/LEFT)
EO A
UDIO
SIGN
AL
TAP20BT/40BT
(SLAVE/RIGHT)
Bluetooth audio device
Note: The loudspeaker that is connected to your source device is the "master"; the linked
loudspeaker is the "slave". The source device sends its signal to the master, and the master
relays the signal to the slave.The stereo signal will be splited between the two loudspeakers:
the master loudspeaker will play the left channel; the slave loudspeaker will play the right
channel.
Tip: When using two loudspeakers, we recommend labeling the master loudspeaker so you
can distinguish between the two units in future setups.
1.Press and hold the PAIR BUTTOM for 3 seconds on both loudspeakers first.
BT RED LEDs will flash and you will hear a tone (beep), wait 10 seconds.
2.Wait for MASTER and SLAVE to link.
When successfully linked, the tones will stop and BT RED LEDs will light solid on both
speakers.
(1) POWER INPUT
Turns the loudspeaker on/off.Make sure the VOLUME
knob is set to "zero" before turning it on.
(2) PAIR BUTTON
Press and release this pair button to pair the loudspeaker (7)
to your Bluetooth device.
Press and hold this pair button for 3 seconds on each
speaker to "link" them for wireless stereo audio.
(3) BALANCED INPUT
Use a standard 1/4" TRS cable to connect your sound
source to this input.
(4) INPUT VOLUME
Turn this knob to adjust the input volume.
(5) PAIR LED
The Bluetooth BLUE LED will flash when the MASTER (7)
speaker is pairing your Bluetooth device.
(6) LINK LED
The Bluetooth RED LED will flash when the both speakers
are linking. The Bluetooth RED LED will light solid when
successfully linked.
(7) STEREO INPUT
Use a standard stereo RCA cable to connect your sound
source to this inputs.
(5)
(6)
TAP20BT
STEREO
INPUT
ON
(1)
PAIR
L
(2)
R
LINE INPUT
OF F
(3)
MADE IN CHINA
MIN
MAX POWER:40W
AC 220-240V/50Hz
MAX
(4)
(5)
(6)
TAP40BT
STEREO
INPUT
L
ON
(1)
PAIR
(2)
R
LINE INPUT
OF F
(3)
MADE IN CHINA
MIN
MAX
MAX POWER:60W
AC 220-240V/50Hz
(4)
3.Choose a MASTER loudspeaker.
MASTER can be either loudspeaker. Be sure to choose only one. The remaining speaker will
be the SLAVE.
4.Press and release PAIR BUTTON on the MASTER loudspeaker only.
You should hear a tone (beep) ; the PAIR BLUE LED will flash.
5.Select SEIKAKU BT2.1ONS on your Bluetooth audio device.
(iPhone, iPad ,Bluetooth adapter etc.)
You should enter the password "2013", When your device's Bluetooth will pair.
5
2
5
Note: Commercial audio installation system must
conform to local building laws. When install speaker
on wall or ceiling, please consult a building constructer
with a license or a professional engineer.The corporation
won't be responsible for the improper installation or
damage because of not conforming to installation
description.
(3)
(1)
(2)
5
Installation Description
Installation Description
Installation procedure of CS-2 bracket is very
simple and convenient, the appearance is pleasing
to the eye.
Step 1: Fasten the CS-2 bracket(1) on the wall with
screws. The wall material must support the weight
of the cabinet.
INDOOR INSTALLATION DESCRIPTION:
TAP series speakers are designed specially for fixing and using in different circumstances. The
property of speakers may be different due to different circumstances. There is an acoustic surface
(wall, floor and ceiling) in a closed room, so the acoustic indoor will turn complex. When acoustic
wave hits the surface, a part of acoustic energy is reflected, and others are absorbed. Reflection and
absorption are depending on the frequencies of acoustic wave and angle of hitting surface. When
operate the cabinet, both man and furniture can absorb the acoustic energy. Please note the
position of man and furniture when installing. Reverberation is the results of the reflected acoustic
wave continue bouncing between the surfaces. Every reflection will loss the energy. When the
acoustic hit the reflection surface, the room will be filled with random reflected acoustic wave. The
music and address will be complex. It is recommended that install more speakers and make the
volume of speakers lower to reduce the reverberation in high reverberating room. (Please see
figure 5B)
Step 2: Place the body of cabinet in CS-2 bracket(2)
and lock the screws tightly
Step 3: Use screw (3) lock CS-2 bracket(1) and
CS-2 bracket(2) and use steel rope (4) to connect
two brackets.
(4)
(eg:TAP20BT)
ONE LOUD SPEAKER
MULTIPLE QUIET SPEAKERS
(figure5A)
(figure5B)
Speaker coverage range
Direct the center axile of the speaker to the flat surface of receiving
area. The speakers of 90 90 series can spread the speaker tone to all the directions at the axile
of 45 . If you use the speakers in large room, you can divide the room to some zones. Then decide
the installing location of the speakers . (Please see figure 6)
45
45
45
45
45
45
45
45
HORIZONTAL
VERTICAL
(figure6)
3
4
Download PDF