! Warning: No operating with power on
F17 Installation Guide
Version: V1.0
Date: April, 2011
3.Lock Connection
(1) Share power with the lock:
+
+12V
GND
-
F17 Mounting Paper
(only for your reference)
In st ru ct io n fo r th e Mo un ti ng P ap er
Be fo re t he d ev ic e is f as te ne d, p le as e
st ic k th e pa pe r to t he p la ce w he re y ou
wa nt t o in st al l it , th en m ak e ho le s an d
la y ca bl es a cc or di ng t o th e mo un ti ng
pa pe r.
DC12V
Wiring Hole
10
NC LOCK
Fixing Hole
-
12
13
+
11
FR 107
(2) Remove the screws on the bottom
(3) Take away the back plate.
+
-
of device.
DC12V
NO LOCK
FR 107
+
BELLBELL+
SEN
GND
BUT
NO1
COM1
NC1
COM2
NO2
Device share power with the lock:
A. ULOCK=12V, I-ILOCK>1A…… ①
B. The lock is near to the device.
(2) Does not share power with the lock:
+
+
FR 107
+
-
(5) Tighten the screws on the bottom,
NC LOCK
BELLBELL+
SEN
GND
BUT
NO1
COM1
NC1
COM2
NO2
+12V
GND
DC12V
-
+
DC power
+
+12V
GND
-
DC12V
(4) Fix the plastic pad and the back
plate on the wall according to the
mounting paper.
-
+
(1) Post the mounting template on the
wall.Drill the holes according to
the marks on the template (holes
for screws and wiring).
BELLBELL+
SEN
GND
BUT
NO1
COM1
NC1
COM2
NO2
+12V
GND
-
-
Fixing Hole
Fixing Hole
+
+
1. Equipment Installation
NO LOCK
FR 107
+
+
DC power
Device does not share power with the lock:
BELLBELL+
SEN
GND
BUT
NO1
COM1
NC1
COM2
NO2
A. ULOCK=12V I-ILOCK≤1A;
B. ULOCK≠12V;
C. The lock is far apart from the device.
fix the device to the back plate.
(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at power on) is connected
with ’NO’ and ’COM’ terminals, and the NC LOCK is connected with ‘NC’ and ’COM’ terminals.
2. Structure and Function
(2) When the Electrical Lock is connected to the Access Control System, you need to parallel one FR107 diode
Access Control System Function
RS485 Converter
(1) If a registered user verified, the device will export the signal
to unlock the door.
TCP/IP
RS485
⑦
⑤
④
①
Exit Button
⑥
②
EXIT
BUTTON
(2) Door sensor will detect the on-off state If the door is unexpected
opened or improperly closed, the alarm signal (digital value) will be
(equipped in the package) to prevent the self-inductance EMF affect the system, do not reverse the polarities.
4. Other Parts Connection:
triggered.
Door Bell
% (4) External card reader is supported.
Door Bell External Reader
③
Alarm
EXIT
BUTTON
Exit Button
Alarm Power
(5) External exit button is supported, it is convenient to open the
door inside.
+
(6) External door bell is supported.
-
(7) Supports RS485, TCP/IP modes to connect with PC. One PC can
manage multiple devices.
Input DC 12V, 500mA (50mA standby)
Positive is connected with ‘+12V’, negative is connected
with ’GND’ (do not reverse the polarities).
%
(3) If only the device being illegally removed, the device will
export alarm signal.
Lock Sensor
BELLBELL+
SEN
GND
BUT
NO1
COM1
NC1
COM2
NO2
5. Power Connection:
Alarm
+
Door Sensor
-
DC12V
Voltage output ≤ DC 12V for Alarm
①:‘I’: device output current, ‘ULOCK’: lock voltage,‘ILOCK’: lock current
+12V
GND
! Warning: No operating with power on
6. Wiegand Output
7. Wiegand Input
The device supports standard Wiegand 26 output,
The device has the function of Wiegand signal input. It supports to
so you can connect it with most of the access control
connect with an independent card reader. They are installed each
devices by now.
side of the door, to control the lock and access together.
Access Control Panel
DATA0
DATA1
GND
WD0
+12V
485+ 485-
RS485
Converter
+12V
GND
WD1
GND
GND
IWD0
RXD
IWD1
TXD
RLED
GND
GLED
485+
485-
485+
485-
BEEP
RS485 Bus
485+
485-
485+
485-
DATA0
DATA1
RLED
GLED
(2) TCP/IP Mode:
BEEP
Two ways for TCP/IP connection.
(1) Please keep the distance between the device and Access Control or Card Reader less than 90 meters(Please use
Wiegand signal extender in long distance or interference environment).
(2) To keep the stability of Wiegand signal, connect the device and the Access Control or Card Reader in same ‘GND’
in any case.
(A) Crossover cable: The device and PC connected
directly.
(B) Straight cable: The device and PC connected to
LAN/WAN through switch/Lanswitch.
Switch
8.Other Functions
…
(1) Manual Reset:
IP Address:192.168.1.124
Side View
If the device does not work properly because of misoperation or
other abnormality, you can use ‘Reset’ function to restart it.
Operation: Remove the black rubber cap, then stick the Reset
button hole with a sharp tool (the tip diameter less than 2mm).
Back View
IP Address:192.168.1.100
Subnet Mask:255.255.255.0
Subnet Mask:255.255.255.0
10. Cautions:
(2) Tamper Function:
In device installation, user need to put a magnet between the device and
the back plate. If the device being illegally moved, and the magnet being
away from the device, it will trigger the alarm.
Reset Button
Tamper Magnet
(1)Power cable is connected after all the other wiring. If the device is working abnormally, please shut down the power
first, then make the necessary check . Kindly reminds you that any hot-plugging may damage the device, and
it is not included in the warranty.
(2)We recommend the DC 3A/12V power supply. Please contact our technical staff for details.
(3)Please read carefully the terminal description and wiring by rule strictly. Any damage caused by improper
operations will be out of the range of our guarantee.
9. Communication
(4)Keep the exposed part of wire less than 5mm, to avoid unexpected connection.
There are two modes that the PC software communicate and exchange information with the device: RS485 and TCP/IP, and
(5)Please connect the ‘GND’ before all the other wiring especially under the environment with much electrostatic.
supports remote control.
(1) RS485 Mode:
Please use specified RS485 wire, RS485 active converter and
bus-type wiring.
Terminals definition please refer to the right table.
(6)Do not change the cable type because of long distance between the power and the device.
Terminals
PC Serial Ports
485+
RS485+
485-
RS485-
(7) Please use specified RS485 wire, RS485 active converter and bus-type wiring. If the communication wire is longer than 100
meters, it is needed to parallel a terminal resistance on the last device of RS485 bus, and the value is about 120 ohm.
Download PDF