SATA DE110 IG.indd

Rugged, Reliable, Mobile, Secure
TM
DataPort
™
SATA DE110 Install Guide
Removable SATA 1.5Gb/s Drive Enclosure
NOTE: For SATA 1.5Gb/s operation, a SATA controller and
appropriate SATA cable are required.
Drive Carrier
JP1
Provides a signal to the Activity Indicator when connected via cable
(provided) to the SATA drive. Some SATA drives/host controllers provide support for the Activity Indicator feature (refer to the SATA drive/
host controller manufacturer’s documentation for further information).
JP1
Key Lock/Drive
Power Switch
Red Cable
Black Cable
(connect to
drive activity on
drive)
Serial ATA
Logo
Reserved
(Pin 14)
Factory Reserved Pins
(J2 - no jumper installed)
I/O Connector
(JP1)
Factory-Installed Jumper (ID0 & ID1)
Factory-installed jumper. Refer to Figures 2 & 4 for further information.
2. Fasten the drive into place with four (4) #6-32 Phillips Flat Hd.
screws. Some drives may require minor adjustment before
securing into carrier with screws. If drive supports the Activity
Indicator feature, connect one end of the Activity Indicator Cable
(provided) to the drive and the other end to JP1 located on Drive
Carrier Board (Figure 1).
NOTE: Some SATA drives/host controllers provide support for the
Activity Indicator feature (refer to the SATA drive/host controller
manufacturer’s documentation for further information). There are two
ways to utilize the Activity Indicator:
a. Drive connection (cable included) to JP1 located on Drive
Carrier Board (Figure 1).
or
b. Host connection (cable not included) to J2 Pin 13 located on
Receiving Frame Motherboard (Figure 2).
Activity Indicator
Pin 13 is used for host connection (cable not included) to the Activity Indicator. Some SATA drives/host controllers provide support for
the Activity Indicator feature (refer to the SATA drive/host controller
manufacturer’s documentation for further information).
3. Install the provided drive cover.
Installation
Spacer Plates (optional)
1. Carefully insert the drive into the carrier. Slide the drive towards
the Drive Carrier Board, so that the I/O connector on the drive
mates with the connector on the Drive Carrier Board. Turn the
drive/carrier assembly over.
Factory
Installed
Jumper
Figure 2: Receiving Frame
Motherboard (Rear View)
“Universal” Receiving Frame Motherboard
Factory Reserved Pins
These pins are reserved for factory use only - Do not install jumper
under any circumstances!
Factory Installed
Jumper
Activity
Indicator
(Pin 13)
Figure 1: Drive Carrier
Remote Activity LED (RLED)
These pins provide a remote LED device activity indicator (Pin 13 =
Cathode, Pin 14 = Anode).
Option Pin
Connector (W1)
DC Power
Connector (P1)
The SATA DE110 is designed to fit most computer systems with
standard 5.25” peripheral slots. The installation of the spacer plates
(provided) may or may not be necessary.
NOTE: Depending on the computer system, spacer plates may be
positioned on the receiving frame to utilize either top or bottom row
of side-mounting holes.
1-800-260-9800
www.CRU-DataPort.com
Rugged, Reliable, Mobile, Secure
TM
DataPort
™
Selecting the Unit ID Number: Use the alignment tool (provided)
to select the ID number of the disk drive.
Drive Cover (provided)
Universal
Receiving
Frame
Serial ATA Drive
(not included)
Drive Carrier
Board
Drive
Carrier
NOTE: The lock on the Data Express serves as a power switch. It must
be engaged (turned counterclockwise) for the Data Express to power
up and function properly.
Figure 5: Unit ID Select
Switch Location
Figure 3: Drive Installation Assembly
Optional Activity Indicator
Cable (included)
Spacer Plate*
(2 total)
*NOTE: Installation
of Spacer Plates is
optional
#6-32 Philips
F.H. Screw
(6 total)
Important Notes Regarding the “Universal” Receiving Frame
Existing PATA DE110 carriers and new SATA DE110 carriers will both
work in SATA “universal” receiving frames. “Universal” receiving
frames are indicated by their BLUE LED. Existing DE110 carriers are
indicated by a Data Express Logo, while the new SATA DE110 carriers
are indicated by the SATA logo.
SATA DE110 carriers will only work in SATA DE110 “universal” receiving frames (indicated by their BLUE LED). Existing PATA DE110 receiving
frames are indicated by their GREEN LED.
For SATA 1.5Gb/s operation, a SATA controller and appropriate SATA
cable are required.
Unit ID Select Switch Settings
Unit ID Select
Rotating Switch
Drive Carrier
Guide
Typical Data Express
Receiving Frame
Product Warranty
CRU-DataPort (CRU) warrants the Data Express DE110 to be free of
significant defects in material and workmanship for a period of five years
from the original date of purchase. CRU’s warranty is nontransferable and is
limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties. CRU expressly disclaims all other warranties, including but not limited to, the implied
warranties of merchantability and fitness for a particular purpose and non-infringement of third-party rights with respect to the documentation and hardware.
No CRU dealer, agent or employee is authorized to make any modification, extension, or addition to this warranty. In no event will CRU or its suppliers be liable
for any costs of procurement of substitute products or services, lost profits, loss
of information or data, computer malfunction, or any other special, indirect, consequential, or incidental damages arising in any way out of the sale of, use of,
or inability to use any CRU product or service, even if CRU has been advised of
the possibility of such damages. In no case shall CRU’s liability exceed the actual
money paid for the products at issue. CRU reserves the right to make modifications and additions to this product without notice or taking on additional liability.
Certification
NOTE: The unit ID number display is for ID display purposes only.
The following table lists the unit ID select switch settings and the valid
AT/IDE unit numbers. Please note that all invalid switch settings have
X’s and result in a blank display in the receiving frame window.
EMI Standard:
EMC Standard:
FCC Part 15 Class B, CE
EN55022, EN55024
FCC Certification
This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received;
including interference that may cause undesired operation.
Register your product at www.CRU-DataPort.com and be
automatically entered to win a free prize!
A7-110-0001 Rev. 1.1
Figure 4: Unit ID Select Switch Settings
1-800-260-9800
www.CRU-DataPort.com
Download PDF